1/* SPDX-License-Identifier: GPL-2.0-or-later */ 2/* 3 * OpenRISC entry.S 4 * 5 * Linux architectural port borrowing liberally from similar works of 6 * others. All original copyrights apply as per the original source 7 * declaration. 8 * 9 * Modifications for the OpenRISC architecture: 10 * Copyright (C) 2003 Matjaz Breskvar <phoenix@bsemi.com> 11 * Copyright (C) 2005 Gyorgy Jeney <nog@bsemi.com> 12 * Copyright (C) 2010-2011 Jonas Bonn <jonas@southpole.se> 13 */ 14 15#include <linux/linkage.h> 16 17#include <asm/processor.h> 18#include <asm/unistd.h> 19#include <asm/thread_info.h> 20#include <asm/errno.h> 21#include <asm/spr_defs.h> 22#include <asm/page.h> 23#include <asm/mmu.h> 24#include <asm/pgtable.h> 25#include <asm/asm-offsets.h> 26 27#define DISABLE_INTERRUPTS(t1,t2) \ 28 l.mfspr t2,r0,SPR_SR ;\ 29 l.movhi t1,hi(~(SPR_SR_IEE|SPR_SR_TEE)) ;\ 30 l.ori t1,t1,lo(~(SPR_SR_IEE|SPR_SR_TEE)) ;\ 31 l.and t2,t2,t1 ;\ 32 l.mtspr r0,t2,SPR_SR 33 34#define ENABLE_INTERRUPTS(t1) \ 35 l.mfspr t1,r0,SPR_SR ;\ 36 l.ori t1,t1,lo(SPR_SR_IEE|SPR_SR_TEE) ;\ 37 l.mtspr r0,t1,SPR_SR 38 39/* =========================================================[ macros ]=== */ 40 41#ifdef CONFIG_TRACE_IRQFLAGS 42/* 43 * Trace irq on/off creating a stack frame. 44 */ 45#define TRACE_IRQS_OP(trace_op) \ 46 l.sw -8(r1),r2 /* store frame pointer */ ;\ 47 l.sw -4(r1),r9 /* store return address */ ;\ 48 l.addi r2,r1,0 /* move sp to fp */ ;\ 49 l.jal trace_op ;\ 50 l.addi r1,r1,-8 ;\ 51 l.ori r1,r2,0 /* restore sp */ ;\ 52 l.lwz r9,-4(r1) /* restore return address */ ;\ 53 l.lwz r2,-8(r1) /* restore fp */ ;\ 54/* 55 * Trace irq on/off and save registers we need that would otherwise be 56 * clobbered. 57 */ 58#define TRACE_IRQS_SAVE(t1,trace_op) \ 59 l.sw -12(r1),t1 /* save extra reg */ ;\ 60 l.sw -8(r1),r2 /* store frame pointer */ ;\ 61 l.sw -4(r1),r9 /* store return address */ ;\ 62 l.addi r2,r1,0 /* move sp to fp */ ;\ 63 l.jal trace_op ;\ 64 l.addi r1,r1,-12 ;\ 65 l.ori r1,r2,0 /* restore sp */ ;\ 66 l.lwz r9,-4(r1) /* restore return address */ ;\ 67 l.lwz r2,-8(r1) /* restore fp */ ;\ 68 l.lwz t1,-12(r1) /* restore extra reg */ 69 70#define TRACE_IRQS_OFF TRACE_IRQS_OP(trace_hardirqs_off) 71#define TRACE_IRQS_ON TRACE_IRQS_OP(trace_hardirqs_on) 72#define TRACE_IRQS_ON_SYSCALL \ 73 TRACE_IRQS_SAVE(r10,trace_hardirqs_on) ;\ 74 l.lwz r3,PT_GPR3(r1) ;\ 75 l.lwz r4,PT_GPR4(r1) ;\ 76 l.lwz r5,PT_GPR5(r1) ;\ 77 l.lwz r6,PT_GPR6(r1) ;\ 78 l.lwz r7,PT_GPR7(r1) ;\ 79 l.lwz r8,PT_GPR8(r1) ;\ 80 l.lwz r11,PT_GPR11(r1) 81#define TRACE_IRQS_OFF_ENTRY \ 82 l.lwz r5,PT_SR(r1) ;\ 83 l.andi r3,r5,(SPR_SR_IEE|SPR_SR_TEE) ;\ 84 l.sfeq r5,r0 /* skip trace if irqs were already off */;\ 85 l.bf 1f ;\ 86 l.nop ;\ 87 TRACE_IRQS_SAVE(r4,trace_hardirqs_off) ;\ 881: 89#else 90#define TRACE_IRQS_OFF 91#define TRACE_IRQS_ON 92#define TRACE_IRQS_OFF_ENTRY 93#define TRACE_IRQS_ON_SYSCALL 94#endif 95 96/* 97 * We need to disable interrupts at beginning of RESTORE_ALL 98 * since interrupt might come in after we've loaded EPC return address 99 * and overwrite EPC with address somewhere in RESTORE_ALL 100 * which is of course wrong! 101 */ 102 103#define RESTORE_ALL \ 104 DISABLE_INTERRUPTS(r3,r4) ;\ 105 l.lwz r3,PT_PC(r1) ;\ 106 l.mtspr r0,r3,SPR_EPCR_BASE ;\ 107 l.lwz r3,PT_SR(r1) ;\ 108 l.mtspr r0,r3,SPR_ESR_BASE ;\ 109 l.lwz r2,PT_GPR2(r1) ;\ 110 l.lwz r3,PT_GPR3(r1) ;\ 111 l.lwz r4,PT_GPR4(r1) ;\ 112 l.lwz r5,PT_GPR5(r1) ;\ 113 l.lwz r6,PT_GPR6(r1) ;\ 114 l.lwz r7,PT_GPR7(r1) ;\ 115 l.lwz r8,PT_GPR8(r1) ;\ 116 l.lwz r9,PT_GPR9(r1) ;\ 117 l.lwz r10,PT_GPR10(r1) ;\ 118 l.lwz r11,PT_GPR11(r1) ;\ 119 l.lwz r12,PT_GPR12(r1) ;\ 120 l.lwz r13,PT_GPR13(r1) ;\ 121 l.lwz r14,PT_GPR14(r1) ;\ 122 l.lwz r15,PT_GPR15(r1) ;\ 123 l.lwz r16,PT_GPR16(r1) ;\ 124 l.lwz r17,PT_GPR17(r1) ;\ 125 l.lwz r18,PT_GPR18(r1) ;\ 126 l.lwz r19,PT_GPR19(r1) ;\ 127 l.lwz r20,PT_GPR20(r1) ;\ 128 l.lwz r21,PT_GPR21(r1) ;\ 129 l.lwz r22,PT_GPR22(r1) ;\ 130 l.lwz r23,PT_GPR23(r1) ;\ 131 l.lwz r24,PT_GPR24(r1) ;\ 132 l.lwz r25,PT_GPR25(r1) ;\ 133 l.lwz r26,PT_GPR26(r1) ;\ 134 l.lwz r27,PT_GPR27(r1) ;\ 135 l.lwz r28,PT_GPR28(r1) ;\ 136 l.lwz r29,PT_GPR29(r1) ;\ 137 l.lwz r30,PT_GPR30(r1) ;\ 138 l.lwz r31,PT_GPR31(r1) ;\ 139 l.lwz r1,PT_SP(r1) ;\ 140 l.rfe 141 142 143#define EXCEPTION_ENTRY(handler) \ 144 .global handler ;\ 145handler: ;\ 146 /* r1, EPCR, ESR a already saved */ ;\ 147 l.sw PT_GPR2(r1),r2 ;\ 148 l.sw PT_GPR3(r1),r3 ;\ 149 /* r4 already save */ ;\ 150 l.sw PT_GPR5(r1),r5 ;\ 151 l.sw PT_GPR6(r1),r6 ;\ 152 l.sw PT_GPR7(r1),r7 ;\ 153 l.sw PT_GPR8(r1),r8 ;\ 154 l.sw PT_GPR9(r1),r9 ;\ 155 /* r10 already saved */ ;\ 156 l.sw PT_GPR11(r1),r11 ;\ 157 /* r12 already saved */ ;\ 158 l.sw PT_GPR13(r1),r13 ;\ 159 l.sw PT_GPR14(r1),r14 ;\ 160 l.sw PT_GPR15(r1),r15 ;\ 161 l.sw PT_GPR16(r1),r16 ;\ 162 l.sw PT_GPR17(r1),r17 ;\ 163 l.sw PT_GPR18(r1),r18 ;\ 164 l.sw PT_GPR19(r1),r19 ;\ 165 l.sw PT_GPR20(r1),r20 ;\ 166 l.sw PT_GPR21(r1),r21 ;\ 167 l.sw PT_GPR22(r1),r22 ;\ 168 l.sw PT_GPR23(r1),r23 ;\ 169 l.sw PT_GPR24(r1),r24 ;\ 170 l.sw PT_GPR25(r1),r25 ;\ 171 l.sw PT_GPR26(r1),r26 ;\ 172 l.sw PT_GPR27(r1),r27 ;\ 173 l.sw PT_GPR28(r1),r28 ;\ 174 l.sw PT_GPR29(r1),r29 ;\ 175 /* r30 already save */ ;\ 176/* l.sw PT_GPR30(r1),r30*/ ;\ 177 l.sw PT_GPR31(r1),r31 ;\ 178 TRACE_IRQS_OFF_ENTRY ;\ 179 /* Store -1 in orig_gpr11 for non-syscall exceptions */ ;\ 180 l.addi r30,r0,-1 ;\ 181 l.sw PT_ORIG_GPR11(r1),r30 182 183#define UNHANDLED_EXCEPTION(handler,vector) \ 184 .global handler ;\ 185handler: ;\ 186 /* r1, EPCR, ESR already saved */ ;\ 187 l.sw PT_GPR2(r1),r2 ;\ 188 l.sw PT_GPR3(r1),r3 ;\ 189 l.sw PT_GPR5(r1),r5 ;\ 190 l.sw PT_GPR6(r1),r6 ;\ 191 l.sw PT_GPR7(r1),r7 ;\ 192 l.sw PT_GPR8(r1),r8 ;\ 193 l.sw PT_GPR9(r1),r9 ;\ 194 /* r10 already saved */ ;\ 195 l.sw PT_GPR11(r1),r11 ;\ 196 /* r12 already saved */ ;\ 197 l.sw PT_GPR13(r1),r13 ;\ 198 l.sw PT_GPR14(r1),r14 ;\ 199 l.sw PT_GPR15(r1),r15 ;\ 200 l.sw PT_GPR16(r1),r16 ;\ 201 l.sw PT_GPR17(r1),r17 ;\ 202 l.sw PT_GPR18(r1),r18 ;\ 203 l.sw PT_GPR19(r1),r19 ;\ 204 l.sw PT_GPR20(r1),r20 ;\ 205 l.sw PT_GPR21(r1),r21 ;\ 206 l.sw PT_GPR22(r1),r22 ;\ 207 l.sw PT_GPR23(r1),r23 ;\ 208 l.sw PT_GPR24(r1),r24 ;\ 209 l.sw PT_GPR25(r1),r25 ;\ 210 l.sw PT_GPR26(r1),r26 ;\ 211 l.sw PT_GPR27(r1),r27 ;\ 212 l.sw PT_GPR28(r1),r28 ;\ 213 l.sw PT_GPR29(r1),r29 ;\ 214 /* r31 already saved */ ;\ 215 l.sw PT_GPR30(r1),r30 ;\ 216/* l.sw PT_GPR31(r1),r31 */ ;\ 217 /* Store -1 in orig_gpr11 for non-syscall exceptions */ ;\ 218 l.addi r30,r0,-1 ;\ 219 l.sw PT_ORIG_GPR11(r1),r30 ;\ 220 l.addi r3,r1,0 ;\ 221 /* r4 is exception EA */ ;\ 222 l.addi r5,r0,vector ;\ 223 l.jal unhandled_exception ;\ 224 l.nop ;\ 225 l.j _ret_from_exception ;\ 226 l.nop 227 228/* clobbers 'reg' */ 229#define CLEAR_LWA_FLAG(reg) \ 230 l.movhi reg,hi(lwa_flag) ;\ 231 l.ori reg,reg,lo(lwa_flag) ;\ 232 l.sw 0(reg),r0 233/* 234 * NOTE: one should never assume that SPR_EPC, SPR_ESR, SPR_EEAR 235 * contain the same values as when exception we're handling 236 * occured. in fact they never do. if you need them use 237 * values saved on stack (for SPR_EPC, SPR_ESR) or content 238 * of r4 (for SPR_EEAR). for details look at EXCEPTION_HANDLE() 239 * in 'arch/openrisc/kernel/head.S' 240 */ 241 242/* =====================================================[ exceptions] === */ 243 244/* ---[ 0x100: RESET exception ]----------------------------------------- */ 245 246EXCEPTION_ENTRY(_tng_kernel_start) 247 l.jal _start 248 l.andi r0,r0,0 249 250/* ---[ 0x200: BUS exception ]------------------------------------------- */ 251 252EXCEPTION_ENTRY(_bus_fault_handler) 253 CLEAR_LWA_FLAG(r3) 254 /* r4: EA of fault (set by EXCEPTION_HANDLE) */ 255 l.jal do_bus_fault 256 l.addi r3,r1,0 /* pt_regs */ 257 258 l.j _ret_from_exception 259 l.nop 260 261/* ---[ 0x300: Data Page Fault exception ]------------------------------- */ 262EXCEPTION_ENTRY(_dtlb_miss_page_fault_handler) 263 CLEAR_LWA_FLAG(r3) 264 l.and r5,r5,r0 265 l.j 1f 266 l.nop 267 268EXCEPTION_ENTRY(_data_page_fault_handler) 269 CLEAR_LWA_FLAG(r3) 270 /* set up parameters for do_page_fault */ 271 l.ori r5,r0,0x300 // exception vector 2721: 273 l.addi r3,r1,0 // pt_regs 274 /* r4 set be EXCEPTION_HANDLE */ // effective address of fault 275 276#ifdef CONFIG_OPENRISC_NO_SPR_SR_DSX 277 l.lwz r6,PT_PC(r3) // address of an offending insn 278 l.lwz r6,0(r6) // instruction that caused pf 279 280 l.srli r6,r6,26 // check opcode for jump insn 281 l.sfeqi r6,0 // l.j 282 l.bf 8f 283 l.sfeqi r6,1 // l.jal 284 l.bf 8f 285 l.sfeqi r6,3 // l.bnf 286 l.bf 8f 287 l.sfeqi r6,4 // l.bf 288 l.bf 8f 289 l.sfeqi r6,0x11 // l.jr 290 l.bf 8f 291 l.sfeqi r6,0x12 // l.jalr 292 l.bf 8f 293 l.nop 294 295 l.j 9f 296 l.nop 297 2988: // offending insn is in delay slot 299 l.lwz r6,PT_PC(r3) // address of an offending insn 300 l.addi r6,r6,4 301 l.lwz r6,0(r6) // instruction that caused pf 302 l.srli r6,r6,26 // get opcode 3039: // offending instruction opcode loaded in r6 304 305#else 306 307 l.mfspr r6,r0,SPR_SR // SR 308 l.andi r6,r6,SPR_SR_DSX // check for delay slot exception 309 l.sfne r6,r0 // exception happened in delay slot 310 l.bnf 7f 311 l.lwz r6,PT_PC(r3) // address of an offending insn 312 313 l.addi r6,r6,4 // offending insn is in delay slot 3147: 315 l.lwz r6,0(r6) // instruction that caused pf 316 l.srli r6,r6,26 // check opcode for write access 317#endif 318 319 l.sfgeui r6,0x33 // check opcode for write access 320 l.bnf 1f 321 l.sfleui r6,0x37 322 l.bnf 1f 323 l.ori r6,r0,0x1 // write access 324 l.j 2f 325 l.nop 3261: l.ori r6,r0,0x0 // !write access 3272: 328 329 /* call fault.c handler in or32/mm/fault.c */ 330 l.jal do_page_fault 331 l.nop 332 l.j _ret_from_exception 333 l.nop 334 335/* ---[ 0x400: Insn Page Fault exception ]------------------------------- */ 336EXCEPTION_ENTRY(_itlb_miss_page_fault_handler) 337 CLEAR_LWA_FLAG(r3) 338 l.and r5,r5,r0 339 l.j 1f 340 l.nop 341 342EXCEPTION_ENTRY(_insn_page_fault_handler) 343 CLEAR_LWA_FLAG(r3) 344 /* set up parameters for do_page_fault */ 345 l.ori r5,r0,0x400 // exception vector 3461: 347 l.addi r3,r1,0 // pt_regs 348 /* r4 set be EXCEPTION_HANDLE */ // effective address of fault 349 l.ori r6,r0,0x0 // !write access 350 351 /* call fault.c handler in or32/mm/fault.c */ 352 l.jal do_page_fault 353 l.nop 354 l.j _ret_from_exception 355 l.nop 356 357 358/* ---[ 0x500: Timer exception ]----------------------------------------- */ 359 360EXCEPTION_ENTRY(_timer_handler) 361 CLEAR_LWA_FLAG(r3) 362 l.jal timer_interrupt 363 l.addi r3,r1,0 /* pt_regs */ 364 365 l.j _ret_from_intr 366 l.nop 367 368/* ---[ 0x600: Alignment exception ]-------------------------------------- */ 369 370EXCEPTION_ENTRY(_alignment_handler) 371 CLEAR_LWA_FLAG(r3) 372 /* r4: EA of fault (set by EXCEPTION_HANDLE) */ 373 l.jal do_unaligned_access 374 l.addi r3,r1,0 /* pt_regs */ 375 376 l.j _ret_from_exception 377 l.nop 378 379#if 0 380EXCEPTION_ENTRY(_alignment_handler) 381// l.mfspr r2,r0,SPR_EEAR_BASE /* Load the effective address */ 382 l.addi r2,r4,0 383// l.mfspr r5,r0,SPR_EPCR_BASE /* Load the insn address */ 384 l.lwz r5,PT_PC(r1) 385 386 l.lwz r3,0(r5) /* Load insn */ 387 l.srli r4,r3,26 /* Shift left to get the insn opcode */ 388 389 l.sfeqi r4,0x00 /* Check if the load/store insn is in delay slot */ 390 l.bf jmp 391 l.sfeqi r4,0x01 392 l.bf jmp 393 l.sfeqi r4,0x03 394 l.bf jmp 395 l.sfeqi r4,0x04 396 l.bf jmp 397 l.sfeqi r4,0x11 398 l.bf jr 399 l.sfeqi r4,0x12 400 l.bf jr 401 l.nop 402 l.j 1f 403 l.addi r5,r5,4 /* Increment PC to get return insn address */ 404 405jmp: 406 l.slli r4,r3,6 /* Get the signed extended jump length */ 407 l.srai r4,r4,4 408 409 l.lwz r3,4(r5) /* Load the real load/store insn */ 410 411 l.add r5,r5,r4 /* Calculate jump target address */ 412 413 l.j 1f 414 l.srli r4,r3,26 /* Shift left to get the insn opcode */ 415 416jr: 417 l.slli r4,r3,9 /* Shift to get the reg nb */ 418 l.andi r4,r4,0x7c 419 420 l.lwz r3,4(r5) /* Load the real load/store insn */ 421 422 l.add r4,r4,r1 /* Load the jump register value from the stack */ 423 l.lwz r5,0(r4) 424 425 l.srli r4,r3,26 /* Shift left to get the insn opcode */ 426 427 4281: 429// l.mtspr r0,r5,SPR_EPCR_BASE 430 l.sw PT_PC(r1),r5 431 432 l.sfeqi r4,0x26 433 l.bf lhs 434 l.sfeqi r4,0x25 435 l.bf lhz 436 l.sfeqi r4,0x22 437 l.bf lws 438 l.sfeqi r4,0x21 439 l.bf lwz 440 l.sfeqi r4,0x37 441 l.bf sh 442 l.sfeqi r4,0x35 443 l.bf sw 444 l.nop 445 4461: l.j 1b /* I don't know what to do */ 447 l.nop 448 449lhs: l.lbs r5,0(r2) 450 l.slli r5,r5,8 451 l.lbz r6,1(r2) 452 l.or r5,r5,r6 453 l.srli r4,r3,19 454 l.andi r4,r4,0x7c 455 l.add r4,r4,r1 456 l.j align_end 457 l.sw 0(r4),r5 458 459lhz: l.lbz r5,0(r2) 460 l.slli r5,r5,8 461 l.lbz r6,1(r2) 462 l.or r5,r5,r6 463 l.srli r4,r3,19 464 l.andi r4,r4,0x7c 465 l.add r4,r4,r1 466 l.j align_end 467 l.sw 0(r4),r5 468 469lws: l.lbs r5,0(r2) 470 l.slli r5,r5,24 471 l.lbz r6,1(r2) 472 l.slli r6,r6,16 473 l.or r5,r5,r6 474 l.lbz r6,2(r2) 475 l.slli r6,r6,8 476 l.or r5,r5,r6 477 l.lbz r6,3(r2) 478 l.or r5,r5,r6 479 l.srli r4,r3,19 480 l.andi r4,r4,0x7c 481 l.add r4,r4,r1 482 l.j align_end 483 l.sw 0(r4),r5 484 485lwz: l.lbz r5,0(r2) 486 l.slli r5,r5,24 487 l.lbz r6,1(r2) 488 l.slli r6,r6,16 489 l.or r5,r5,r6 490 l.lbz r6,2(r2) 491 l.slli r6,r6,8 492 l.or r5,r5,r6 493 l.lbz r6,3(r2) 494 l.or r5,r5,r6 495 l.srli r4,r3,19 496 l.andi r4,r4,0x7c 497 l.add r4,r4,r1 498 l.j align_end 499 l.sw 0(r4),r5 500 501sh: 502 l.srli r4,r3,9 503 l.andi r4,r4,0x7c 504 l.add r4,r4,r1 505 l.lwz r5,0(r4) 506 l.sb 1(r2),r5 507 l.srli r5,r5,8 508 l.j align_end 509 l.sb 0(r2),r5 510 511sw: 512 l.srli r4,r3,9 513 l.andi r4,r4,0x7c 514 l.add r4,r4,r1 515 l.lwz r5,0(r4) 516 l.sb 3(r2),r5 517 l.srli r5,r5,8 518 l.sb 2(r2),r5 519 l.srli r5,r5,8 520 l.sb 1(r2),r5 521 l.srli r5,r5,8 522 l.j align_end 523 l.sb 0(r2),r5 524 525align_end: 526 l.j _ret_from_intr 527 l.nop 528#endif 529 530/* ---[ 0x700: Illegal insn exception ]---------------------------------- */ 531 532EXCEPTION_ENTRY(_illegal_instruction_handler) 533 /* r4: EA of fault (set by EXCEPTION_HANDLE) */ 534 l.jal do_illegal_instruction 535 l.addi r3,r1,0 /* pt_regs */ 536 537 l.j _ret_from_exception 538 l.nop 539 540/* ---[ 0x800: External interrupt exception ]---------------------------- */ 541 542EXCEPTION_ENTRY(_external_irq_handler) 543#ifdef CONFIG_OPENRISC_ESR_EXCEPTION_BUG_CHECK 544 l.lwz r4,PT_SR(r1) // were interrupts enabled ? 545 l.andi r4,r4,SPR_SR_IEE 546 l.sfeqi r4,0 547 l.bnf 1f // ext irq enabled, all ok. 548 l.nop 549 550 l.addi r1,r1,-0x8 551 l.movhi r3,hi(42f) 552 l.ori r3,r3,lo(42f) 553 l.sw 0x0(r1),r3 554 l.jal printk 555 l.sw 0x4(r1),r4 556 l.addi r1,r1,0x8 557 558 .section .rodata, "a" 55942: 560 .string "\n\rESR interrupt bug: in _external_irq_handler (ESR %x)\n\r" 561 .align 4 562 .previous 563 564 l.ori r4,r4,SPR_SR_IEE // fix the bug 565// l.sw PT_SR(r1),r4 5661: 567#endif 568 CLEAR_LWA_FLAG(r3) 569 l.addi r3,r1,0 570 l.movhi r8,hi(do_IRQ) 571 l.ori r8,r8,lo(do_IRQ) 572 l.jalr r8 573 l.nop 574 l.j _ret_from_intr 575 l.nop 576 577/* ---[ 0x900: DTLB miss exception ]------------------------------------- */ 578 579 580/* ---[ 0xa00: ITLB miss exception ]------------------------------------- */ 581 582 583/* ---[ 0xb00: Range exception ]----------------------------------------- */ 584 585UNHANDLED_EXCEPTION(_vector_0xb00,0xb00) 586 587/* ---[ 0xc00: Syscall exception ]--------------------------------------- */ 588 589/* 590 * Syscalls are a special type of exception in that they are 591 * _explicitly_ invoked by userspace and can therefore be 592 * held to conform to the same ABI as normal functions with 593 * respect to whether registers are preserved across the call 594 * or not. 595 */ 596 597/* Upon syscall entry we just save the callee-saved registers 598 * and not the call-clobbered ones. 599 */ 600 601_string_syscall_return: 602 .string "syscall return %ld \n\r\0" 603 .align 4 604 605ENTRY(_sys_call_handler) 606 /* r1, EPCR, ESR a already saved */ 607 l.sw PT_GPR2(r1),r2 608 /* r3-r8 must be saved because syscall restart relies 609 * on us being able to restart the syscall args... technically 610 * they should be clobbered, otherwise 611 */ 612 l.sw PT_GPR3(r1),r3 613 /* 614 * r4 already saved 615 * r4 holds the EEAR address of the fault, use it as screatch reg and 616 * then load the original r4 617 */ 618 CLEAR_LWA_FLAG(r4) 619 l.lwz r4,PT_GPR4(r1) 620 l.sw PT_GPR5(r1),r5 621 l.sw PT_GPR6(r1),r6 622 l.sw PT_GPR7(r1),r7 623 l.sw PT_GPR8(r1),r8 624 l.sw PT_GPR9(r1),r9 625 /* r10 already saved */ 626 l.sw PT_GPR11(r1),r11 627 /* orig_gpr11 must be set for syscalls */ 628 l.sw PT_ORIG_GPR11(r1),r11 629 /* r12,r13 already saved */ 630 631 /* r14-r28 (even) aren't touched by the syscall fast path below 632 * so we don't need to save them. However, the functions that return 633 * to userspace via a call to switch() DO need to save these because 634 * switch() effectively clobbers them... saving these registers for 635 * such functions is handled in their syscall wrappers (see fork, vfork, 636 * and clone, below). 637 638 /* r30 is the only register we clobber in the fast path */ 639 /* r30 already saved */ 640/* l.sw PT_GPR30(r1),r30 */ 641 642_syscall_check_trace_enter: 643 /* syscalls run with interrupts enabled */ 644 TRACE_IRQS_ON_SYSCALL 645 ENABLE_INTERRUPTS(r29) // enable interrupts, r29 is temp 646 647 /* If TIF_SYSCALL_TRACE is set, then we want to do syscall tracing */ 648 l.lwz r30,TI_FLAGS(r10) 649 l.andi r30,r30,_TIF_SYSCALL_TRACE 650 l.sfne r30,r0 651 l.bf _syscall_trace_enter 652 l.nop 653 654_syscall_check: 655 /* Ensure that the syscall number is reasonable */ 656 l.sfgeui r11,__NR_syscalls 657 l.bf _syscall_badsys 658 l.nop 659 660_syscall_call: 661 l.movhi r29,hi(sys_call_table) 662 l.ori r29,r29,lo(sys_call_table) 663 l.slli r11,r11,2 664 l.add r29,r29,r11 665 l.lwz r29,0(r29) 666 667 l.jalr r29 668 l.nop 669 670_syscall_return: 671 /* All syscalls return here... just pay attention to ret_from_fork 672 * which does it in a round-about way. 673 */ 674 l.sw PT_GPR11(r1),r11 // save return value 675 676#if 0 677_syscall_debug: 678 l.movhi r3,hi(_string_syscall_return) 679 l.ori r3,r3,lo(_string_syscall_return) 680 l.ori r27,r0,1 681 l.sw -4(r1),r27 682 l.sw -8(r1),r11 683 l.addi r1,r1,-8 684 l.movhi r27,hi(printk) 685 l.ori r27,r27,lo(printk) 686 l.jalr r27 687 l.nop 688 l.addi r1,r1,8 689#endif 690 691_syscall_check_trace_leave: 692 /* r30 is a callee-saved register so this should still hold the 693 * _TIF_SYSCALL_TRACE flag from _syscall_check_trace_enter above... 694 * _syscall_trace_leave expects syscall result to be in pt_regs->r11. 695 */ 696 l.sfne r30,r0 697 l.bf _syscall_trace_leave 698 l.nop 699 700/* This is where the exception-return code begins... interrupts need to be 701 * disabled the rest of the way here because we can't afford to miss any 702 * interrupts that set NEED_RESCHED or SIGNALPENDING... really true? */ 703 704_syscall_check_work: 705 /* Here we need to disable interrupts */ 706 DISABLE_INTERRUPTS(r27,r29) 707 TRACE_IRQS_OFF 708 l.lwz r30,TI_FLAGS(r10) 709 l.andi r30,r30,_TIF_WORK_MASK 710 l.sfne r30,r0 711 712 l.bnf _syscall_resume_userspace 713 l.nop 714 715 /* Work pending follows a different return path, so we need to 716 * make sure that all the call-saved registers get into pt_regs 717 * before branching... 718 */ 719 l.sw PT_GPR14(r1),r14 720 l.sw PT_GPR16(r1),r16 721 l.sw PT_GPR18(r1),r18 722 l.sw PT_GPR20(r1),r20 723 l.sw PT_GPR22(r1),r22 724 l.sw PT_GPR24(r1),r24 725 l.sw PT_GPR26(r1),r26 726 l.sw PT_GPR28(r1),r28 727 728 /* _work_pending needs to be called with interrupts disabled */ 729 l.j _work_pending 730 l.nop 731 732_syscall_resume_userspace: 733// ENABLE_INTERRUPTS(r29) 734 735 736/* This is the hot path for returning to userspace from a syscall. If there's 737 * work to be done and the branch to _work_pending was taken above, then the 738 * return to userspace will be done via the normal exception return path... 739 * that path restores _all_ registers and will overwrite the "clobbered" 740 * registers with whatever garbage is in pt_regs -- that's OK because those 741 * registers are clobbered anyway and because the extra work is insignificant 742 * in the context of the extra work that _work_pending is doing. 743 744/* Once again, syscalls are special and only guarantee to preserve the 745 * same registers as a normal function call */ 746 747/* The assumption here is that the registers r14-r28 (even) are untouched and 748 * don't need to be restored... be sure that that's really the case! 749 */ 750 751/* This is still too much... we should only be restoring what we actually 752 * clobbered... we should even be using 'scratch' (odd) regs above so that 753 * we don't need to restore anything, hardly... 754 */ 755 756 l.lwz r2,PT_GPR2(r1) 757 758 /* Restore args */ 759 /* r3-r8 are technically clobbered, but syscall restart needs these 760 * to be restored... 761 */ 762 l.lwz r3,PT_GPR3(r1) 763 l.lwz r4,PT_GPR4(r1) 764 l.lwz r5,PT_GPR5(r1) 765 l.lwz r6,PT_GPR6(r1) 766 l.lwz r7,PT_GPR7(r1) 767 l.lwz r8,PT_GPR8(r1) 768 769 l.lwz r9,PT_GPR9(r1) 770 l.lwz r10,PT_GPR10(r1) 771 l.lwz r11,PT_GPR11(r1) 772 773 /* r30 is the only register we clobber in the fast path */ 774 l.lwz r30,PT_GPR30(r1) 775 776 /* Here we use r13-r19 (odd) as scratch regs */ 777 l.lwz r13,PT_PC(r1) 778 l.lwz r15,PT_SR(r1) 779 l.lwz r1,PT_SP(r1) 780 /* Interrupts need to be disabled for setting EPCR and ESR 781 * so that another interrupt doesn't come in here and clobber 782 * them before we can use them for our l.rfe */ 783 DISABLE_INTERRUPTS(r17,r19) 784 l.mtspr r0,r13,SPR_EPCR_BASE 785 l.mtspr r0,r15,SPR_ESR_BASE 786 l.rfe 787 788/* End of hot path! 789 * Keep the below tracing and error handling out of the hot path... 790*/ 791 792_syscall_trace_enter: 793 /* Here we pass pt_regs to do_syscall_trace_enter. Make sure 794 * that function is really getting all the info it needs as 795 * pt_regs isn't a complete set of userspace regs, just the 796 * ones relevant to the syscall... 797 * 798 * Note use of delay slot for setting argument. 799 */ 800 l.jal do_syscall_trace_enter 801 l.addi r3,r1,0 802 803 /* Restore arguments (not preserved across do_syscall_trace_enter) 804 * so that we can do the syscall for real and return to the syscall 805 * hot path. 806 */ 807 l.lwz r11,PT_GPR11(r1) 808 l.lwz r3,PT_GPR3(r1) 809 l.lwz r4,PT_GPR4(r1) 810 l.lwz r5,PT_GPR5(r1) 811 l.lwz r6,PT_GPR6(r1) 812 l.lwz r7,PT_GPR7(r1) 813 814 l.j _syscall_check 815 l.lwz r8,PT_GPR8(r1) 816 817_syscall_trace_leave: 818 l.jal do_syscall_trace_leave 819 l.addi r3,r1,0 820 821 l.j _syscall_check_work 822 l.nop 823 824_syscall_badsys: 825 /* Here we effectively pretend to have executed an imaginary 826 * syscall that returns -ENOSYS and then return to the regular 827 * syscall hot path. 828 * Note that "return value" is set in the delay slot... 829 */ 830 l.j _syscall_return 831 l.addi r11,r0,-ENOSYS 832 833/******* END SYSCALL HANDLING *******/ 834 835/* ---[ 0xd00: Trap exception ]------------------------------------------ */ 836 837UNHANDLED_EXCEPTION(_vector_0xd00,0xd00) 838 839/* ---[ 0xe00: Trap exception ]------------------------------------------ */ 840 841EXCEPTION_ENTRY(_trap_handler) 842 CLEAR_LWA_FLAG(r3) 843 /* r4: EA of fault (set by EXCEPTION_HANDLE) */ 844 l.jal do_trap 845 l.addi r3,r1,0 /* pt_regs */ 846 847 l.j _ret_from_exception 848 l.nop 849 850/* ---[ 0xf00: Reserved exception ]-------------------------------------- */ 851 852UNHANDLED_EXCEPTION(_vector_0xf00,0xf00) 853 854/* ---[ 0x1000: Reserved exception ]------------------------------------- */ 855 856UNHANDLED_EXCEPTION(_vector_0x1000,0x1000) 857 858/* ---[ 0x1100: Reserved exception ]------------------------------------- */ 859 860UNHANDLED_EXCEPTION(_vector_0x1100,0x1100) 861 862/* ---[ 0x1200: Reserved exception ]------------------------------------- */ 863 864UNHANDLED_EXCEPTION(_vector_0x1200,0x1200) 865 866/* ---[ 0x1300: Reserved exception ]------------------------------------- */ 867 868UNHANDLED_EXCEPTION(_vector_0x1300,0x1300) 869 870/* ---[ 0x1400: Reserved exception ]------------------------------------- */ 871 872UNHANDLED_EXCEPTION(_vector_0x1400,0x1400) 873 874/* ---[ 0x1500: Reserved exception ]------------------------------------- */ 875 876UNHANDLED_EXCEPTION(_vector_0x1500,0x1500) 877 878/* ---[ 0x1600: Reserved exception ]------------------------------------- */ 879 880UNHANDLED_EXCEPTION(_vector_0x1600,0x1600) 881 882/* ---[ 0x1700: Reserved exception ]------------------------------------- */ 883 884UNHANDLED_EXCEPTION(_vector_0x1700,0x1700) 885 886/* ---[ 0x1800: Reserved exception ]------------------------------------- */ 887 888UNHANDLED_EXCEPTION(_vector_0x1800,0x1800) 889 890/* ---[ 0x1900: Reserved exception ]------------------------------------- */ 891 892UNHANDLED_EXCEPTION(_vector_0x1900,0x1900) 893 894/* ---[ 0x1a00: Reserved exception ]------------------------------------- */ 895 896UNHANDLED_EXCEPTION(_vector_0x1a00,0x1a00) 897 898/* ---[ 0x1b00: Reserved exception ]------------------------------------- */ 899 900UNHANDLED_EXCEPTION(_vector_0x1b00,0x1b00) 901 902/* ---[ 0x1c00: Reserved exception ]------------------------------------- */ 903 904UNHANDLED_EXCEPTION(_vector_0x1c00,0x1c00) 905 906/* ---[ 0x1d00: Reserved exception ]------------------------------------- */ 907 908UNHANDLED_EXCEPTION(_vector_0x1d00,0x1d00) 909 910/* ---[ 0x1e00: Reserved exception ]------------------------------------- */ 911 912UNHANDLED_EXCEPTION(_vector_0x1e00,0x1e00) 913 914/* ---[ 0x1f00: Reserved exception ]------------------------------------- */ 915 916UNHANDLED_EXCEPTION(_vector_0x1f00,0x1f00) 917 918/* ========================================================[ return ] === */ 919 920_resume_userspace: 921 DISABLE_INTERRUPTS(r3,r4) 922 TRACE_IRQS_OFF 923 l.lwz r4,TI_FLAGS(r10) 924 l.andi r13,r4,_TIF_WORK_MASK 925 l.sfeqi r13,0 926 l.bf _restore_all 927 l.nop 928 929_work_pending: 930 l.lwz r5,PT_ORIG_GPR11(r1) 931 l.sfltsi r5,0 932 l.bnf 1f 933 l.nop 934 l.andi r5,r5,0 9351: 936 l.jal do_work_pending 937 l.ori r3,r1,0 /* pt_regs */ 938 939 l.sfeqi r11,0 940 l.bf _restore_all 941 l.nop 942 l.sfltsi r11,0 943 l.bnf 1f 944 l.nop 945 l.and r11,r11,r0 946 l.ori r11,r11,__NR_restart_syscall 947 l.j _syscall_check_trace_enter 948 l.nop 9491: 950 l.lwz r11,PT_ORIG_GPR11(r1) 951 /* Restore arg registers */ 952 l.lwz r3,PT_GPR3(r1) 953 l.lwz r4,PT_GPR4(r1) 954 l.lwz r5,PT_GPR5(r1) 955 l.lwz r6,PT_GPR6(r1) 956 l.lwz r7,PT_GPR7(r1) 957 l.j _syscall_check_trace_enter 958 l.lwz r8,PT_GPR8(r1) 959 960_restore_all: 961#ifdef CONFIG_TRACE_IRQFLAGS 962 l.lwz r4,PT_SR(r1) 963 l.andi r3,r4,(SPR_SR_IEE|SPR_SR_TEE) 964 l.sfeq r3,r0 /* skip trace if irqs were off */ 965 l.bf skip_hardirqs_on 966 l.nop 967 TRACE_IRQS_ON 968skip_hardirqs_on: 969#endif 970 RESTORE_ALL 971 /* This returns to userspace code */ 972 973 974ENTRY(_ret_from_intr) 975ENTRY(_ret_from_exception) 976 l.lwz r4,PT_SR(r1) 977 l.andi r3,r4,SPR_SR_SM 978 l.sfeqi r3,0 979 l.bnf _restore_all 980 l.nop 981 l.j _resume_userspace 982 l.nop 983 984ENTRY(ret_from_fork) 985 l.jal schedule_tail 986 l.nop 987 988 /* Check if we are a kernel thread */ 989 l.sfeqi r20,0 990 l.bf 1f 991 l.nop 992 993 /* ...we are a kernel thread so invoke the requested callback */ 994 l.jalr r20 995 l.or r3,r22,r0 996 9971: 998 /* _syscall_returns expect r11 to contain return value */ 999 l.lwz r11,PT_GPR11(r1) 1000 1001 /* The syscall fast path return expects call-saved registers 1002 * r12-r28 to be untouched, so we restore them here as they 1003 * will have been effectively clobbered when arriving here 1004 * via the call to switch() 1005 */ 1006 l.lwz r12,PT_GPR12(r1) 1007 l.lwz r14,PT_GPR14(r1) 1008 l.lwz r16,PT_GPR16(r1) 1009 l.lwz r18,PT_GPR18(r1) 1010 l.lwz r20,PT_GPR20(r1) 1011 l.lwz r22,PT_GPR22(r1) 1012 l.lwz r24,PT_GPR24(r1) 1013 l.lwz r26,PT_GPR26(r1) 1014 l.lwz r28,PT_GPR28(r1) 1015 1016 l.j _syscall_return 1017 l.nop 1018 1019/* ========================================================[ switch ] === */ 1020 1021/* 1022 * This routine switches between two different tasks. The process 1023 * state of one is saved on its kernel stack. Then the state 1024 * of the other is restored from its kernel stack. The memory 1025 * management hardware is updated to the second process's state. 1026 * Finally, we can return to the second process, via the 'return'. 1027 * 1028 * Note: there are two ways to get to the "going out" portion 1029 * of this code; either by coming in via the entry (_switch) 1030 * or via "fork" which must set up an environment equivalent 1031 * to the "_switch" path. If you change this (or in particular, the 1032 * SAVE_REGS macro), you'll have to change the fork code also. 1033 */ 1034 1035 1036/* _switch MUST never lay on page boundry, cause it runs from 1037 * effective addresses and beeing interrupted by iTLB miss would kill it. 1038 * dTLB miss seams to never accour in the bad place since data accesses 1039 * are from task structures which are always page aligned. 1040 * 1041 * The problem happens in RESTORE_ALL_NO_R11 where we first set the EPCR 1042 * register, then load the previous register values and only at the end call 1043 * the l.rfe instruction. If get TLB miss in beetwen the EPCR register gets 1044 * garbled and we end up calling l.rfe with the wrong EPCR. (same probably 1045 * holds for ESR) 1046 * 1047 * To avoid this problems it is sufficient to align _switch to 1048 * some nice round number smaller than it's size... 1049 */ 1050 1051/* ABI rules apply here... we either enter _switch via schedule() or via 1052 * an imaginary call to which we shall return at return_from_fork. Either 1053 * way, we are a function call and only need to preserve the callee-saved 1054 * registers when we return. As such, we don't need to save the registers 1055 * on the stack that we won't be returning as they were... 1056 */ 1057 1058 .align 0x400 1059ENTRY(_switch) 1060 /* We don't store SR as _switch only gets called in a context where 1061 * the SR will be the same going in and coming out... */ 1062 1063 /* Set up new pt_regs struct for saving task state */ 1064 l.addi r1,r1,-(INT_FRAME_SIZE) 1065 1066 /* No need to store r1/PT_SP as it goes into KSP below */ 1067 l.sw PT_GPR2(r1),r2 1068 l.sw PT_GPR9(r1),r9 1069 /* This is wrong, r12 shouldn't be here... but GCC is broken for the time being 1070 * and expects r12 to be callee-saved... */ 1071 l.sw PT_GPR12(r1),r12 1072 l.sw PT_GPR14(r1),r14 1073 l.sw PT_GPR16(r1),r16 1074 l.sw PT_GPR18(r1),r18 1075 l.sw PT_GPR20(r1),r20 1076 l.sw PT_GPR22(r1),r22 1077 l.sw PT_GPR24(r1),r24 1078 l.sw PT_GPR26(r1),r26 1079 l.sw PT_GPR28(r1),r28 1080 l.sw PT_GPR30(r1),r30 1081 1082 l.addi r11,r10,0 /* Save old 'current' to 'last' return value*/ 1083 1084 /* We use thread_info->ksp for storing the address of the above 1085 * structure so that we can get back to it later... we don't want 1086 * to lose the value of thread_info->ksp, though, so store it as 1087 * pt_regs->sp so that we can easily restore it when we are made 1088 * live again... 1089 */ 1090 1091 /* Save the old value of thread_info->ksp as pt_regs->sp */ 1092 l.lwz r29,TI_KSP(r10) 1093 l.sw PT_SP(r1),r29 1094 1095 /* Swap kernel stack pointers */ 1096 l.sw TI_KSP(r10),r1 /* Save old stack pointer */ 1097 l.or r10,r4,r0 /* Set up new current_thread_info */ 1098 l.lwz r1,TI_KSP(r10) /* Load new stack pointer */ 1099 1100 /* Restore the old value of thread_info->ksp */ 1101 l.lwz r29,PT_SP(r1) 1102 l.sw TI_KSP(r10),r29 1103 1104 /* ...and restore the registers, except r11 because the return value 1105 * has already been set above. 1106 */ 1107 l.lwz r2,PT_GPR2(r1) 1108 l.lwz r9,PT_GPR9(r1) 1109 /* No need to restore r10 */ 1110 /* ...and do not restore r11 */ 1111 1112 /* This is wrong, r12 shouldn't be here... but GCC is broken for the time being 1113 * and expects r12 to be callee-saved... */ 1114 l.lwz r12,PT_GPR12(r1) 1115 l.lwz r14,PT_GPR14(r1) 1116 l.lwz r16,PT_GPR16(r1) 1117 l.lwz r18,PT_GPR18(r1) 1118 l.lwz r20,PT_GPR20(r1) 1119 l.lwz r22,PT_GPR22(r1) 1120 l.lwz r24,PT_GPR24(r1) 1121 l.lwz r26,PT_GPR26(r1) 1122 l.lwz r28,PT_GPR28(r1) 1123 l.lwz r30,PT_GPR30(r1) 1124 1125 /* Unwind stack to pre-switch state */ 1126 l.addi r1,r1,(INT_FRAME_SIZE) 1127 1128 /* Return via the link-register back to where we 'came from', where 1129 * that may be either schedule(), ret_from_fork(), or 1130 * ret_from_kernel_thread(). If we are returning to a new thread, 1131 * we are expected to have set up the arg to schedule_tail already, 1132 * hence we do so here unconditionally: 1133 */ 1134 l.lwz r3,TI_TASK(r3) /* Load 'prev' as schedule_tail arg */ 1135 l.jr r9 1136 l.nop 1137 1138/* ==================================================================== */ 1139 1140/* These all use the delay slot for setting the argument register, so the 1141 * jump is always happening after the l.addi instruction. 1142 * 1143 * These are all just wrappers that don't touch the link-register r9, so the 1144 * return from the "real" syscall function will return back to the syscall 1145 * code that did the l.jal that brought us here. 1146 */ 1147 1148/* fork requires that we save all the callee-saved registers because they 1149 * are all effectively clobbered by the call to _switch. Here we store 1150 * all the registers that aren't touched by the syscall fast path and thus 1151 * weren't saved there. 1152 */ 1153 1154_fork_save_extra_regs_and_call: 1155 l.sw PT_GPR14(r1),r14 1156 l.sw PT_GPR16(r1),r16 1157 l.sw PT_GPR18(r1),r18 1158 l.sw PT_GPR20(r1),r20 1159 l.sw PT_GPR22(r1),r22 1160 l.sw PT_GPR24(r1),r24 1161 l.sw PT_GPR26(r1),r26 1162 l.jr r29 1163 l.sw PT_GPR28(r1),r28 1164 1165ENTRY(__sys_clone) 1166 l.movhi r29,hi(sys_clone) 1167 l.ori r29,r29,lo(sys_clone) 1168 l.j _fork_save_extra_regs_and_call 1169 l.addi r7,r1,0 1170 1171ENTRY(__sys_fork) 1172 l.movhi r29,hi(sys_fork) 1173 l.ori r29,r29,lo(sys_fork) 1174 l.j _fork_save_extra_regs_and_call 1175 l.addi r3,r1,0 1176 1177ENTRY(sys_rt_sigreturn) 1178 l.jal _sys_rt_sigreturn 1179 l.addi r3,r1,0 1180 l.sfne r30,r0 1181 l.bnf _no_syscall_trace 1182 l.nop 1183 l.jal do_syscall_trace_leave 1184 l.addi r3,r1,0 1185_no_syscall_trace: 1186 l.j _resume_userspace 1187 l.nop 1188 1189/* This is a catch-all syscall for atomic instructions for the OpenRISC 1000. 1190 * The functions takes a variable number of parameters depending on which 1191 * particular flavour of atomic you want... parameter 1 is a flag identifying 1192 * the atomic in question. Currently, this function implements the 1193 * following variants: 1194 * 1195 * XCHG: 1196 * @flag: 1 1197 * @ptr1: 1198 * @ptr2: 1199 * Atomically exchange the values in pointers 1 and 2. 1200 * 1201 */ 1202 1203ENTRY(sys_or1k_atomic) 1204 /* FIXME: This ignores r3 and always does an XCHG */ 1205 DISABLE_INTERRUPTS(r17,r19) 1206 l.lwz r29,0(r4) 1207 l.lwz r27,0(r5) 1208 l.sw 0(r4),r27 1209 l.sw 0(r5),r29 1210 ENABLE_INTERRUPTS(r17) 1211 l.jr r9 1212 l.or r11,r0,r0 1213 1214/* ============================================================[ EOF ]=== */ 1215