1 // SPDX-License-Identifier: GPL-2.0-only 2 /* 3 * Ilitek ILI9322 TFT LCD drm_panel driver. 4 * 5 * This panel can be configured to support: 6 * - 8-bit serial RGB interface 7 * - 24-bit parallel RGB interface 8 * - 8-bit ITU-R BT.601 interface 9 * - 8-bit ITU-R BT.656 interface 10 * - Up to 320RGBx240 dots resolution TFT LCD displays 11 * - Scaling, brightness and contrast 12 * 13 * The scaling means that the display accepts a 640x480 or 720x480 14 * input and rescales it to fit to the 320x240 display. So what we 15 * present to the system is something else than what comes out on the 16 * actual display. 17 * 18 * Copyright (C) 2017 Linus Walleij <linus.walleij@linaro.org> 19 * Derived from drivers/drm/gpu/panel/panel-samsung-ld9040.c 20 */ 21 22 #include <linux/bitops.h> 23 #include <linux/gpio/consumer.h> 24 #include <linux/module.h> 25 #include <linux/of_device.h> 26 #include <linux/regmap.h> 27 #include <linux/regulator/consumer.h> 28 #include <linux/spi/spi.h> 29 30 #include <video/mipi_display.h> 31 #include <video/of_videomode.h> 32 #include <video/videomode.h> 33 34 #include <drm/drm_modes.h> 35 #include <drm/drm_panel.h> 36 #include <drm/drm_print.h> 37 38 #define ILI9322_CHIP_ID 0x00 39 #define ILI9322_CHIP_ID_MAGIC 0x96 40 41 /* 42 * Voltage on the communication interface, from 0.7 (0x00) 43 * to 1.32 (0x1f) times the VREG1OUT voltage in 2% increments. 44 * 1.00 (0x0f) is the default. 45 */ 46 #define ILI9322_VCOM_AMP 0x01 47 48 /* 49 * High voltage on the communication signals, from 0.37 (0x00) to 50 * 1.0 (0x3f) times the VREGOUT1 voltage in 1% increments. 51 * 0.83 (0x2e) is the default. 52 */ 53 #define ILI9322_VCOM_HIGH 0x02 54 55 /* 56 * VREG1 voltage regulator from 3.6V (0x00) to 6.0V (0x18) in 0.1V 57 * increments. 5.4V (0x12) is the default. This is the reference 58 * voltage for the VCOM levels and the greyscale level. 59 */ 60 #define ILI9322_VREG1_VOLTAGE 0x03 61 62 /* Describes the incoming signal */ 63 #define ILI9322_ENTRY 0x06 64 /* 0 = right-to-left, 1 = left-to-right (default), horizontal flip */ 65 #define ILI9322_ENTRY_HDIR BIT(0) 66 /* 0 = down-to-up, 1 = up-to-down (default), vertical flip */ 67 #define ILI9322_ENTRY_VDIR BIT(1) 68 /* NTSC, PAL or autodetect */ 69 #define ILI9322_ENTRY_NTSC (0 << 2) 70 #define ILI9322_ENTRY_PAL (1 << 2) 71 #define ILI9322_ENTRY_AUTODETECT (3 << 2) 72 /* Input format */ 73 #define ILI9322_ENTRY_SERIAL_RGB_THROUGH (0 << 4) 74 #define ILI9322_ENTRY_SERIAL_RGB_ALIGNED (1 << 4) 75 #define ILI9322_ENTRY_SERIAL_RGB_DUMMY_320X240 (2 << 4) 76 #define ILI9322_ENTRY_SERIAL_RGB_DUMMY_360X240 (3 << 4) 77 #define ILI9322_ENTRY_DISABLE_1 (4 << 4) 78 #define ILI9322_ENTRY_PARALLEL_RGB_THROUGH (5 << 4) 79 #define ILI9322_ENTRY_PARALLEL_RGB_ALIGNED (6 << 4) 80 #define ILI9322_ENTRY_YUV_640Y_320CBCR_25_54_MHZ (7 << 4) 81 #define ILI9322_ENTRY_YUV_720Y_360CBCR_27_MHZ (8 << 4) 82 #define ILI9322_ENTRY_DISABLE_2 (9 << 4) 83 #define ILI9322_ENTRY_ITU_R_BT_656_720X360 (10 << 4) 84 #define ILI9322_ENTRY_ITU_R_BT_656_640X320 (11 << 4) 85 86 /* Power control */ 87 #define ILI9322_POW_CTRL 0x07 88 #define ILI9322_POW_CTRL_STB BIT(0) /* 0 = standby, 1 = normal */ 89 #define ILI9322_POW_CTRL_VGL BIT(1) /* 0 = off, 1 = on */ 90 #define ILI9322_POW_CTRL_VGH BIT(2) /* 0 = off, 1 = on */ 91 #define ILI9322_POW_CTRL_DDVDH BIT(3) /* 0 = off, 1 = on */ 92 #define ILI9322_POW_CTRL_VCOM BIT(4) /* 0 = off, 1 = on */ 93 #define ILI9322_POW_CTRL_VCL BIT(5) /* 0 = off, 1 = on */ 94 #define ILI9322_POW_CTRL_AUTO BIT(6) /* 0 = interactive, 1 = auto */ 95 #define ILI9322_POW_CTRL_STANDBY (ILI9322_POW_CTRL_VGL | \ 96 ILI9322_POW_CTRL_VGH | \ 97 ILI9322_POW_CTRL_DDVDH | \ 98 ILI9322_POW_CTRL_VCL | \ 99 ILI9322_POW_CTRL_AUTO | \ 100 BIT(7)) 101 #define ILI9322_POW_CTRL_DEFAULT (ILI9322_POW_CTRL_STANDBY | \ 102 ILI9322_POW_CTRL_STB) 103 104 /* Vertical back porch bits 0..5 */ 105 #define ILI9322_VBP 0x08 106 107 /* Horizontal back porch, 8 bits */ 108 #define ILI9322_HBP 0x09 109 110 /* 111 * Polarity settings: 112 * 1 = positive polarity 113 * 0 = negative polarity 114 */ 115 #define ILI9322_POL 0x0a 116 #define ILI9322_POL_DCLK BIT(0) /* 1 default */ 117 #define ILI9322_POL_HSYNC BIT(1) /* 0 default */ 118 #define ILI9322_POL_VSYNC BIT(2) /* 0 default */ 119 #define ILI9322_POL_DE BIT(3) /* 1 default */ 120 /* 121 * 0 means YCBCR are ordered Cb0,Y0,Cr0,Y1,Cb2,Y2,Cr2,Y3 (default) 122 * in RGB mode this means RGB comes in RGBRGB 123 * 1 means YCBCR are ordered Cr0,Y0,Cb0,Y1,Cr2,Y2,Cb2,Y3 124 * in RGB mode this means RGB comes in BGRBGR 125 */ 126 #define ILI9322_POL_YCBCR_MODE BIT(4) 127 /* Formula A for YCbCR->RGB = 0, Formula B = 1 */ 128 #define ILI9322_POL_FORMULA BIT(5) 129 /* Reverse polarity: 0 = 0..255, 1 = 255..0 */ 130 #define ILI9322_POL_REV BIT(6) 131 132 #define ILI9322_IF_CTRL 0x0b 133 #define ILI9322_IF_CTRL_HSYNC_VSYNC 0x00 134 #define ILI9322_IF_CTRL_HSYNC_VSYNC_DE BIT(2) 135 #define ILI9322_IF_CTRL_DE_ONLY BIT(3) 136 #define ILI9322_IF_CTRL_SYNC_DISABLED (BIT(2) | BIT(3)) 137 #define ILI9322_IF_CTRL_LINE_INVERSION BIT(0) /* Not set means frame inv */ 138 139 #define ILI9322_GLOBAL_RESET 0x04 140 #define ILI9322_GLOBAL_RESET_ASSERT 0x00 /* bit 0 = 0 -> reset */ 141 142 /* 143 * 4+4 bits of negative and positive gamma correction 144 * Upper nybble, bits 4-7 are negative gamma 145 * Lower nybble, bits 0-3 are positive gamma 146 */ 147 #define ILI9322_GAMMA_1 0x10 148 #define ILI9322_GAMMA_2 0x11 149 #define ILI9322_GAMMA_3 0x12 150 #define ILI9322_GAMMA_4 0x13 151 #define ILI9322_GAMMA_5 0x14 152 #define ILI9322_GAMMA_6 0x15 153 #define ILI9322_GAMMA_7 0x16 154 #define ILI9322_GAMMA_8 0x17 155 156 /** 157 * enum ili9322_input - the format of the incoming signal to the panel 158 * 159 * The panel can be connected to various input streams and four of them can 160 * be selected by electronic straps on the display. However it is possible 161 * to select another mode or override the electronic default with this 162 * setting. 163 */ 164 enum ili9322_input { 165 ILI9322_INPUT_SRGB_THROUGH = 0x0, 166 ILI9322_INPUT_SRGB_ALIGNED = 0x1, 167 ILI9322_INPUT_SRGB_DUMMY_320X240 = 0x2, 168 ILI9322_INPUT_SRGB_DUMMY_360X240 = 0x3, 169 ILI9322_INPUT_DISABLED_1 = 0x4, 170 ILI9322_INPUT_PRGB_THROUGH = 0x5, 171 ILI9322_INPUT_PRGB_ALIGNED = 0x6, 172 ILI9322_INPUT_YUV_640X320_YCBCR = 0x7, 173 ILI9322_INPUT_YUV_720X360_YCBCR = 0x8, 174 ILI9322_INPUT_DISABLED_2 = 0x9, 175 ILI9322_INPUT_ITU_R_BT656_720X360_YCBCR = 0xa, 176 ILI9322_INPUT_ITU_R_BT656_640X320_YCBCR = 0xb, 177 ILI9322_INPUT_UNKNOWN = 0xc, 178 }; 179 180 static const char * const ili9322_inputs[] = { 181 "8 bit serial RGB through", 182 "8 bit serial RGB aligned", 183 "8 bit serial RGB dummy 320x240", 184 "8 bit serial RGB dummy 360x240", 185 "disabled 1", 186 "24 bit parallel RGB through", 187 "24 bit parallel RGB aligned", 188 "24 bit YUV 640Y 320CbCr", 189 "24 bit YUV 720Y 360CbCr", 190 "disabled 2", 191 "8 bit ITU-R BT.656 720Y 360CbCr", 192 "8 bit ITU-R BT.656 640Y 320CbCr", 193 }; 194 195 /** 196 * struct ili9322_config - the system specific ILI9322 configuration 197 * @width_mm: physical panel width [mm] 198 * @height_mm: physical panel height [mm] 199 * @flip_horizontal: flip the image horizontally (right-to-left scan) 200 * (only in RGB and YUV modes) 201 * @flip_vertical: flip the image vertically (down-to-up scan) 202 * (only in RGB and YUV modes) 203 * @input: the input/entry type used in this system, if this is set to 204 * ILI9322_INPUT_UNKNOWN the driver will try to figure it out by probing 205 * the hardware 206 * @vreg1out_mv: the output in microvolts for the VREGOUT1 regulator used 207 * to drive the physical display. Valid ranges are 3600 thru 6000 in 100 208 * microvolt increments. If not specified, hardware defaults will be 209 * used (4.5V). 210 * @vcom_high_percent: the percentage of VREGOUT1 used for the peak 211 * voltage on the communications link. Valid ranges are 37 thru 100 212 * percent. If not specified, hardware defaults will be used (91%). 213 * @vcom_amplitude_percent: the percentage of VREGOUT1 used for the 214 * peak-to-peak amplitude of the communcation signals to the physical 215 * display. Valid ranges are 70 thru 132 percent in increments if two 216 * percent. Odd percentages will be truncated. If not specified, hardware 217 * defaults will be used (114%). 218 * @dclk_active_high: data/pixel clock active high, data will be clocked 219 * in on the rising edge of the DCLK (this is usually the case). 220 * @syncmode: The synchronization mode, what sync signals are emitted. 221 * See the enum for details. 222 * @de_active_high: DE (data entry) is active high 223 * @hsync_active_high: HSYNC is active high 224 * @vsync_active_high: VSYNC is active high 225 * @gamma_corr_pos: a set of 8 nybbles describing positive 226 * gamma correction for voltages V1 thru V8. Valid range 0..15 227 * @gamma_corr_neg: a set of 8 nybbles describing negative 228 * gamma correction for voltages V1 thru V8. Valid range 0..15 229 * 230 * These adjust what grayscale voltage will be output for input data V1 = 0, 231 * V2 = 16, V3 = 48, V4 = 96, V5 = 160, V6 = 208, V7 = 240 and V8 = 255. 232 * The curve is shaped like this: 233 * 234 * ^ 235 * | V8 236 * | V7 237 * | V6 238 * | V5 239 * | V4 240 * | V3 241 * | V2 242 * | V1 243 * +-----------------------------------------------------------> 244 * 0 16 48 96 160 208 240 255 245 * 246 * The negative and postive gamma values adjust the V1 thru V8 up/down 247 * according to the datasheet specifications. This is a property of the 248 * physical display connected to the display controller and may vary. 249 * If defined, both arrays must be supplied in full. If the properties 250 * are not supplied, hardware defaults will be used. 251 */ 252 struct ili9322_config { 253 u32 width_mm; 254 u32 height_mm; 255 bool flip_horizontal; 256 bool flip_vertical; 257 enum ili9322_input input; 258 u32 vreg1out_mv; 259 u32 vcom_high_percent; 260 u32 vcom_amplitude_percent; 261 bool dclk_active_high; 262 bool de_active_high; 263 bool hsync_active_high; 264 bool vsync_active_high; 265 u8 syncmode; 266 u8 gamma_corr_pos[8]; 267 u8 gamma_corr_neg[8]; 268 }; 269 270 struct ili9322 { 271 struct device *dev; 272 const struct ili9322_config *conf; 273 struct drm_panel panel; 274 struct regmap *regmap; 275 struct regulator_bulk_data supplies[3]; 276 struct gpio_desc *reset_gpio; 277 enum ili9322_input input; 278 struct videomode vm; 279 u8 gamma[8]; 280 u8 vreg1out; 281 u8 vcom_high; 282 u8 vcom_amplitude; 283 }; 284 285 static inline struct ili9322 *panel_to_ili9322(struct drm_panel *panel) 286 { 287 return container_of(panel, struct ili9322, panel); 288 } 289 290 static int ili9322_regmap_spi_write(void *context, const void *data, 291 size_t count) 292 { 293 struct device *dev = context; 294 struct spi_device *spi = to_spi_device(dev); 295 u8 buf[2]; 296 297 /* Clear bit 7 to write */ 298 memcpy(buf, data, 2); 299 buf[0] &= ~0x80; 300 301 dev_dbg(dev, "WRITE: %02x %02x\n", buf[0], buf[1]); 302 return spi_write_then_read(spi, buf, 2, NULL, 0); 303 } 304 305 static int ili9322_regmap_spi_read(void *context, const void *reg, 306 size_t reg_size, void *val, size_t val_size) 307 { 308 struct device *dev = context; 309 struct spi_device *spi = to_spi_device(dev); 310 u8 buf[1]; 311 312 /* Set bit 7 to 1 to read */ 313 memcpy(buf, reg, 1); 314 dev_dbg(dev, "READ: %02x reg size = %zu, val size = %zu\n", 315 buf[0], reg_size, val_size); 316 buf[0] |= 0x80; 317 318 return spi_write_then_read(spi, buf, 1, val, 1); 319 } 320 321 static struct regmap_bus ili9322_regmap_bus = { 322 .write = ili9322_regmap_spi_write, 323 .read = ili9322_regmap_spi_read, 324 .reg_format_endian_default = REGMAP_ENDIAN_BIG, 325 .val_format_endian_default = REGMAP_ENDIAN_BIG, 326 }; 327 328 static bool ili9322_volatile_reg(struct device *dev, unsigned int reg) 329 { 330 return false; 331 } 332 333 static bool ili9322_writeable_reg(struct device *dev, unsigned int reg) 334 { 335 /* Just register 0 is read-only */ 336 if (reg == 0x00) 337 return false; 338 return true; 339 } 340 341 static const struct regmap_config ili9322_regmap_config = { 342 .reg_bits = 8, 343 .val_bits = 8, 344 .max_register = 0x44, 345 .cache_type = REGCACHE_RBTREE, 346 .volatile_reg = ili9322_volatile_reg, 347 .writeable_reg = ili9322_writeable_reg, 348 }; 349 350 static int ili9322_init(struct drm_panel *panel, struct ili9322 *ili) 351 { 352 u8 reg; 353 int ret; 354 int i; 355 356 /* Reset display */ 357 ret = regmap_write(ili->regmap, ILI9322_GLOBAL_RESET, 358 ILI9322_GLOBAL_RESET_ASSERT); 359 if (ret) { 360 dev_err(ili->dev, "can't issue GRESET (%d)\n", ret); 361 return ret; 362 } 363 364 /* Set up the main voltage regulator */ 365 if (ili->vreg1out != U8_MAX) { 366 ret = regmap_write(ili->regmap, ILI9322_VREG1_VOLTAGE, 367 ili->vreg1out); 368 if (ret) { 369 dev_err(ili->dev, "can't set up VREG1OUT (%d)\n", ret); 370 return ret; 371 } 372 } 373 374 if (ili->vcom_amplitude != U8_MAX) { 375 ret = regmap_write(ili->regmap, ILI9322_VCOM_AMP, 376 ili->vcom_amplitude); 377 if (ret) { 378 dev_err(ili->dev, 379 "can't set up VCOM amplitude (%d)\n", ret); 380 return ret; 381 } 382 }; 383 384 if (ili->vcom_high != U8_MAX) { 385 ret = regmap_write(ili->regmap, ILI9322_VCOM_HIGH, 386 ili->vcom_high); 387 if (ret) { 388 dev_err(ili->dev, "can't set up VCOM high (%d)\n", ret); 389 return ret; 390 } 391 }; 392 393 /* Set up gamma correction */ 394 for (i = 0; i < ARRAY_SIZE(ili->gamma); i++) { 395 ret = regmap_write(ili->regmap, ILI9322_GAMMA_1 + i, 396 ili->gamma[i]); 397 if (ret) { 398 dev_err(ili->dev, 399 "can't write gamma V%d to 0x%02x (%d)\n", 400 i + 1, ILI9322_GAMMA_1 + i, ret); 401 return ret; 402 } 403 } 404 405 /* 406 * Polarity and inverted color order for RGB input. 407 * None of this applies in the BT.656 mode. 408 */ 409 reg = 0; 410 if (ili->conf->dclk_active_high) 411 reg = ILI9322_POL_DCLK; 412 if (ili->conf->de_active_high) 413 reg |= ILI9322_POL_DE; 414 if (ili->conf->hsync_active_high) 415 reg |= ILI9322_POL_HSYNC; 416 if (ili->conf->vsync_active_high) 417 reg |= ILI9322_POL_VSYNC; 418 ret = regmap_write(ili->regmap, ILI9322_POL, reg); 419 if (ret) { 420 dev_err(ili->dev, "can't write POL register (%d)\n", ret); 421 return ret; 422 } 423 424 /* 425 * Set up interface control. 426 * This is not used in the BT.656 mode (no H/Vsync or DE signals). 427 */ 428 reg = ili->conf->syncmode; 429 reg |= ILI9322_IF_CTRL_LINE_INVERSION; 430 ret = regmap_write(ili->regmap, ILI9322_IF_CTRL, reg); 431 if (ret) { 432 dev_err(ili->dev, "can't write IF CTRL register (%d)\n", ret); 433 return ret; 434 } 435 436 /* Set up the input mode */ 437 reg = (ili->input << 4); 438 /* These are inverted, setting to 1 is the default, clearing flips */ 439 if (!ili->conf->flip_horizontal) 440 reg |= ILI9322_ENTRY_HDIR; 441 if (!ili->conf->flip_vertical) 442 reg |= ILI9322_ENTRY_VDIR; 443 reg |= ILI9322_ENTRY_AUTODETECT; 444 ret = regmap_write(ili->regmap, ILI9322_ENTRY, reg); 445 if (ret) { 446 dev_err(ili->dev, "can't write ENTRY reg (%d)\n", ret); 447 return ret; 448 } 449 dev_info(ili->dev, "display is in %s mode, syncmode %02x\n", 450 ili9322_inputs[ili->input], 451 ili->conf->syncmode); 452 453 dev_info(ili->dev, "initialized display\n"); 454 455 return 0; 456 } 457 458 /* 459 * This power-on sequence if from the datasheet, page 57. 460 */ 461 static int ili9322_power_on(struct ili9322 *ili) 462 { 463 int ret; 464 465 /* Assert RESET */ 466 gpiod_set_value(ili->reset_gpio, 1); 467 468 ret = regulator_bulk_enable(ARRAY_SIZE(ili->supplies), ili->supplies); 469 if (ret < 0) { 470 dev_err(ili->dev, "unable to enable regulators\n"); 471 return ret; 472 } 473 msleep(20); 474 475 /* De-assert RESET */ 476 gpiod_set_value(ili->reset_gpio, 0); 477 478 msleep(10); 479 480 return 0; 481 } 482 483 static int ili9322_power_off(struct ili9322 *ili) 484 { 485 return regulator_bulk_disable(ARRAY_SIZE(ili->supplies), ili->supplies); 486 } 487 488 static int ili9322_disable(struct drm_panel *panel) 489 { 490 struct ili9322 *ili = panel_to_ili9322(panel); 491 int ret; 492 493 ret = regmap_write(ili->regmap, ILI9322_POW_CTRL, 494 ILI9322_POW_CTRL_STANDBY); 495 if (ret) { 496 dev_err(ili->dev, "unable to go to standby mode\n"); 497 return ret; 498 } 499 500 return 0; 501 } 502 503 static int ili9322_unprepare(struct drm_panel *panel) 504 { 505 struct ili9322 *ili = panel_to_ili9322(panel); 506 507 return ili9322_power_off(ili); 508 } 509 510 static int ili9322_prepare(struct drm_panel *panel) 511 { 512 struct ili9322 *ili = panel_to_ili9322(panel); 513 int ret; 514 515 ret = ili9322_power_on(ili); 516 if (ret < 0) 517 return ret; 518 519 ret = ili9322_init(panel, ili); 520 if (ret < 0) 521 ili9322_unprepare(panel); 522 523 return ret; 524 } 525 526 static int ili9322_enable(struct drm_panel *panel) 527 { 528 struct ili9322 *ili = panel_to_ili9322(panel); 529 int ret; 530 531 ret = regmap_write(ili->regmap, ILI9322_POW_CTRL, 532 ILI9322_POW_CTRL_DEFAULT); 533 if (ret) { 534 dev_err(ili->dev, "unable to enable panel\n"); 535 return ret; 536 } 537 538 return 0; 539 } 540 541 /* Serial RGB modes */ 542 static const struct drm_display_mode srgb_320x240_mode = { 543 .clock = 2453500, 544 .hdisplay = 320, 545 .hsync_start = 320 + 359, 546 .hsync_end = 320 + 359 + 1, 547 .htotal = 320 + 359 + 1 + 241, 548 .vdisplay = 240, 549 .vsync_start = 240 + 4, 550 .vsync_end = 240 + 4 + 1, 551 .vtotal = 262, 552 .vrefresh = 60, 553 .flags = 0, 554 }; 555 556 static const struct drm_display_mode srgb_360x240_mode = { 557 .clock = 2700000, 558 .hdisplay = 360, 559 .hsync_start = 360 + 35, 560 .hsync_end = 360 + 35 + 1, 561 .htotal = 360 + 35 + 1 + 241, 562 .vdisplay = 240, 563 .vsync_start = 240 + 21, 564 .vsync_end = 240 + 21 + 1, 565 .vtotal = 262, 566 .vrefresh = 60, 567 .flags = 0, 568 }; 569 570 /* This is the only mode listed for parallel RGB in the datasheet */ 571 static const struct drm_display_mode prgb_320x240_mode = { 572 .clock = 6400000, 573 .hdisplay = 320, 574 .hsync_start = 320 + 38, 575 .hsync_end = 320 + 38 + 1, 576 .htotal = 320 + 38 + 1 + 50, 577 .vdisplay = 240, 578 .vsync_start = 240 + 4, 579 .vsync_end = 240 + 4 + 1, 580 .vtotal = 262, 581 .vrefresh = 60, 582 .flags = 0, 583 }; 584 585 /* YUV modes */ 586 static const struct drm_display_mode yuv_640x320_mode = { 587 .clock = 2454000, 588 .hdisplay = 640, 589 .hsync_start = 640 + 252, 590 .hsync_end = 640 + 252 + 1, 591 .htotal = 640 + 252 + 1 + 28, 592 .vdisplay = 320, 593 .vsync_start = 320 + 4, 594 .vsync_end = 320 + 4 + 1, 595 .vtotal = 320 + 4 + 1 + 18, 596 .vrefresh = 60, 597 .flags = 0, 598 }; 599 600 static const struct drm_display_mode yuv_720x360_mode = { 601 .clock = 2700000, 602 .hdisplay = 720, 603 .hsync_start = 720 + 252, 604 .hsync_end = 720 + 252 + 1, 605 .htotal = 720 + 252 + 1 + 24, 606 .vdisplay = 360, 607 .vsync_start = 360 + 4, 608 .vsync_end = 360 + 4 + 1, 609 .vtotal = 360 + 4 + 1 + 18, 610 .vrefresh = 60, 611 .flags = 0, 612 }; 613 614 /* BT.656 VGA mode, 640x480 */ 615 static const struct drm_display_mode itu_r_bt_656_640_mode = { 616 .clock = 2454000, 617 .hdisplay = 640, 618 .hsync_start = 640 + 3, 619 .hsync_end = 640 + 3 + 1, 620 .htotal = 640 + 3 + 1 + 272, 621 .vdisplay = 480, 622 .vsync_start = 480 + 4, 623 .vsync_end = 480 + 4 + 1, 624 .vtotal = 500, 625 .vrefresh = 60, 626 .flags = 0, 627 }; 628 629 /* BT.656 D1 mode 720x480 */ 630 static const struct drm_display_mode itu_r_bt_656_720_mode = { 631 .clock = 2700000, 632 .hdisplay = 720, 633 .hsync_start = 720 + 3, 634 .hsync_end = 720 + 3 + 1, 635 .htotal = 720 + 3 + 1 + 272, 636 .vdisplay = 480, 637 .vsync_start = 480 + 4, 638 .vsync_end = 480 + 4 + 1, 639 .vtotal = 500, 640 .vrefresh = 60, 641 .flags = 0, 642 }; 643 644 static int ili9322_get_modes(struct drm_panel *panel) 645 { 646 struct drm_connector *connector = panel->connector; 647 struct ili9322 *ili = panel_to_ili9322(panel); 648 struct drm_display_mode *mode; 649 struct drm_display_info *info; 650 651 info = &connector->display_info; 652 info->width_mm = ili->conf->width_mm; 653 info->height_mm = ili->conf->height_mm; 654 if (ili->conf->dclk_active_high) 655 info->bus_flags |= DRM_BUS_FLAG_PIXDATA_DRIVE_POSEDGE; 656 else 657 info->bus_flags |= DRM_BUS_FLAG_PIXDATA_DRIVE_NEGEDGE; 658 659 if (ili->conf->de_active_high) 660 info->bus_flags |= DRM_BUS_FLAG_DE_HIGH; 661 else 662 info->bus_flags |= DRM_BUS_FLAG_DE_LOW; 663 664 switch (ili->input) { 665 case ILI9322_INPUT_SRGB_DUMMY_320X240: 666 mode = drm_mode_duplicate(panel->drm, &srgb_320x240_mode); 667 break; 668 case ILI9322_INPUT_SRGB_DUMMY_360X240: 669 mode = drm_mode_duplicate(panel->drm, &srgb_360x240_mode); 670 break; 671 case ILI9322_INPUT_PRGB_THROUGH: 672 case ILI9322_INPUT_PRGB_ALIGNED: 673 mode = drm_mode_duplicate(panel->drm, &prgb_320x240_mode); 674 break; 675 case ILI9322_INPUT_YUV_640X320_YCBCR: 676 mode = drm_mode_duplicate(panel->drm, &yuv_640x320_mode); 677 break; 678 case ILI9322_INPUT_YUV_720X360_YCBCR: 679 mode = drm_mode_duplicate(panel->drm, &yuv_720x360_mode); 680 break; 681 case ILI9322_INPUT_ITU_R_BT656_720X360_YCBCR: 682 mode = drm_mode_duplicate(panel->drm, &itu_r_bt_656_720_mode); 683 break; 684 case ILI9322_INPUT_ITU_R_BT656_640X320_YCBCR: 685 mode = drm_mode_duplicate(panel->drm, &itu_r_bt_656_640_mode); 686 break; 687 default: 688 mode = NULL; 689 break; 690 } 691 if (!mode) { 692 DRM_ERROR("bad mode or failed to add mode\n"); 693 return -EINVAL; 694 } 695 drm_mode_set_name(mode); 696 /* 697 * This is the preferred mode because most people are going 698 * to want to use the display with VGA type graphics. 699 */ 700 mode->type = DRM_MODE_TYPE_DRIVER | DRM_MODE_TYPE_PREFERRED; 701 702 /* Set up the polarity */ 703 if (ili->conf->hsync_active_high) 704 mode->flags |= DRM_MODE_FLAG_PHSYNC; 705 else 706 mode->flags |= DRM_MODE_FLAG_NHSYNC; 707 if (ili->conf->vsync_active_high) 708 mode->flags |= DRM_MODE_FLAG_PVSYNC; 709 else 710 mode->flags |= DRM_MODE_FLAG_NVSYNC; 711 712 mode->width_mm = ili->conf->width_mm; 713 mode->height_mm = ili->conf->height_mm; 714 drm_mode_probed_add(connector, mode); 715 716 return 1; /* Number of modes */ 717 } 718 719 static const struct drm_panel_funcs ili9322_drm_funcs = { 720 .disable = ili9322_disable, 721 .unprepare = ili9322_unprepare, 722 .prepare = ili9322_prepare, 723 .enable = ili9322_enable, 724 .get_modes = ili9322_get_modes, 725 }; 726 727 static int ili9322_probe(struct spi_device *spi) 728 { 729 struct device *dev = &spi->dev; 730 struct ili9322 *ili; 731 const struct regmap_config *regmap_config; 732 u8 gamma; 733 u32 val; 734 int ret; 735 int i; 736 737 ili = devm_kzalloc(dev, sizeof(struct ili9322), GFP_KERNEL); 738 if (!ili) 739 return -ENOMEM; 740 741 spi_set_drvdata(spi, ili); 742 743 ili->dev = dev; 744 745 /* 746 * Every new incarnation of this display must have a unique 747 * data entry for the system in this driver. 748 */ 749 ili->conf = of_device_get_match_data(dev); 750 if (!ili->conf) { 751 dev_err(dev, "missing device configuration\n"); 752 return -ENODEV; 753 } 754 755 val = ili->conf->vreg1out_mv; 756 if (!val) { 757 /* Default HW value, do not touch (should be 4.5V) */ 758 ili->vreg1out = U8_MAX; 759 } else { 760 if (val < 3600) { 761 dev_err(dev, "too low VREG1OUT\n"); 762 return -EINVAL; 763 } 764 if (val > 6000) { 765 dev_err(dev, "too high VREG1OUT\n"); 766 return -EINVAL; 767 } 768 if ((val % 100) != 0) { 769 dev_err(dev, "VREG1OUT is no even 100 microvolt\n"); 770 return -EINVAL; 771 } 772 val -= 3600; 773 val /= 100; 774 dev_dbg(dev, "VREG1OUT = 0x%02x\n", val); 775 ili->vreg1out = val; 776 } 777 778 val = ili->conf->vcom_high_percent; 779 if (!val) { 780 /* Default HW value, do not touch (should be 91%) */ 781 ili->vcom_high = U8_MAX; 782 } else { 783 if (val < 37) { 784 dev_err(dev, "too low VCOM high\n"); 785 return -EINVAL; 786 } 787 if (val > 100) { 788 dev_err(dev, "too high VCOM high\n"); 789 return -EINVAL; 790 } 791 val -= 37; 792 dev_dbg(dev, "VCOM high = 0x%02x\n", val); 793 ili->vcom_high = val; 794 } 795 796 val = ili->conf->vcom_amplitude_percent; 797 if (!val) { 798 /* Default HW value, do not touch (should be 114%) */ 799 ili->vcom_high = U8_MAX; 800 } else { 801 if (val < 70) { 802 dev_err(dev, "too low VCOM amplitude\n"); 803 return -EINVAL; 804 } 805 if (val > 132) { 806 dev_err(dev, "too high VCOM amplitude\n"); 807 return -EINVAL; 808 } 809 val -= 70; 810 val >>= 1; /* Increments of 2% */ 811 dev_dbg(dev, "VCOM amplitude = 0x%02x\n", val); 812 ili->vcom_amplitude = val; 813 } 814 815 for (i = 0; i < ARRAY_SIZE(ili->gamma); i++) { 816 val = ili->conf->gamma_corr_neg[i]; 817 if (val > 15) { 818 dev_err(dev, "negative gamma %u > 15, capping\n", val); 819 val = 15; 820 } 821 gamma = val << 4; 822 val = ili->conf->gamma_corr_pos[i]; 823 if (val > 15) { 824 dev_err(dev, "positive gamma %u > 15, capping\n", val); 825 val = 15; 826 } 827 gamma |= val; 828 ili->gamma[i] = gamma; 829 dev_dbg(dev, "gamma V%d: 0x%02x\n", i + 1, gamma); 830 } 831 832 ili->supplies[0].supply = "vcc"; /* 2.7-3.6 V */ 833 ili->supplies[1].supply = "iovcc"; /* 1.65-3.6V */ 834 ili->supplies[2].supply = "vci"; /* 2.7-3.6V */ 835 ret = devm_regulator_bulk_get(dev, ARRAY_SIZE(ili->supplies), 836 ili->supplies); 837 if (ret < 0) 838 return ret; 839 ret = regulator_set_voltage(ili->supplies[0].consumer, 840 2700000, 3600000); 841 if (ret) 842 return ret; 843 ret = regulator_set_voltage(ili->supplies[1].consumer, 844 1650000, 3600000); 845 if (ret) 846 return ret; 847 ret = regulator_set_voltage(ili->supplies[2].consumer, 848 2700000, 3600000); 849 if (ret) 850 return ret; 851 852 ili->reset_gpio = devm_gpiod_get_optional(dev, "reset", GPIOD_OUT_HIGH); 853 if (IS_ERR(ili->reset_gpio)) { 854 dev_err(dev, "failed to get RESET GPIO\n"); 855 return PTR_ERR(ili->reset_gpio); 856 } 857 858 spi->bits_per_word = 8; 859 ret = spi_setup(spi); 860 if (ret < 0) { 861 dev_err(dev, "spi setup failed.\n"); 862 return ret; 863 } 864 regmap_config = &ili9322_regmap_config; 865 ili->regmap = devm_regmap_init(dev, &ili9322_regmap_bus, dev, 866 regmap_config); 867 if (IS_ERR(ili->regmap)) { 868 dev_err(dev, "failed to allocate register map\n"); 869 return PTR_ERR(ili->regmap); 870 } 871 872 ret = regmap_read(ili->regmap, ILI9322_CHIP_ID, &val); 873 if (ret) { 874 dev_err(dev, "can't get chip ID (%d)\n", ret); 875 return ret; 876 } 877 if (val != ILI9322_CHIP_ID_MAGIC) { 878 dev_err(dev, "chip ID 0x%0x2, expected 0x%02x\n", val, 879 ILI9322_CHIP_ID_MAGIC); 880 return -ENODEV; 881 } 882 883 /* Probe the system to find the display setting */ 884 if (ili->conf->input == ILI9322_INPUT_UNKNOWN) { 885 ret = regmap_read(ili->regmap, ILI9322_ENTRY, &val); 886 if (ret) { 887 dev_err(dev, "can't get entry setting (%d)\n", ret); 888 return ret; 889 } 890 /* Input enum corresponds to HW setting */ 891 ili->input = (val >> 4) & 0x0f; 892 if (ili->input >= ILI9322_INPUT_UNKNOWN) 893 ili->input = ILI9322_INPUT_UNKNOWN; 894 } else { 895 ili->input = ili->conf->input; 896 } 897 898 drm_panel_init(&ili->panel); 899 ili->panel.dev = dev; 900 ili->panel.funcs = &ili9322_drm_funcs; 901 902 return drm_panel_add(&ili->panel); 903 } 904 905 static int ili9322_remove(struct spi_device *spi) 906 { 907 struct ili9322 *ili = spi_get_drvdata(spi); 908 909 ili9322_power_off(ili); 910 drm_panel_remove(&ili->panel); 911 912 return 0; 913 } 914 915 /* 916 * The D-Link DIR-685 panel is marked LM918A01-1A SY-B4-091116-E0199 917 */ 918 static const struct ili9322_config ili9322_dir_685 = { 919 .width_mm = 65, 920 .height_mm = 50, 921 .input = ILI9322_INPUT_ITU_R_BT656_640X320_YCBCR, 922 .vreg1out_mv = 4600, 923 .vcom_high_percent = 91, 924 .vcom_amplitude_percent = 114, 925 .syncmode = ILI9322_IF_CTRL_SYNC_DISABLED, 926 .dclk_active_high = true, 927 .gamma_corr_neg = { 0xa, 0x5, 0x7, 0x7, 0x7, 0x5, 0x1, 0x6 }, 928 .gamma_corr_pos = { 0x7, 0x7, 0x3, 0x2, 0x3, 0x5, 0x7, 0x2 }, 929 }; 930 931 static const struct of_device_id ili9322_of_match[] = { 932 { 933 .compatible = "dlink,dir-685-panel", 934 .data = &ili9322_dir_685, 935 }, 936 { 937 .compatible = "ilitek,ili9322", 938 .data = NULL, 939 }, 940 { } 941 }; 942 MODULE_DEVICE_TABLE(of, ili9322_of_match); 943 944 static struct spi_driver ili9322_driver = { 945 .probe = ili9322_probe, 946 .remove = ili9322_remove, 947 .driver = { 948 .name = "panel-ilitek-ili9322", 949 .of_match_table = ili9322_of_match, 950 }, 951 }; 952 module_spi_driver(ili9322_driver); 953 954 MODULE_AUTHOR("Linus Walleij <linus.walleij@linaro.org>"); 955 MODULE_DESCRIPTION("ILI9322 LCD panel driver"); 956 MODULE_LICENSE("GPL v2"); 957