Kconfig (revision 0be3ff0c) - OpenGrok cross reference for /linux/drivers/net/wan/Kconfig

# SPDX-License-Identifier: GPL-2.0-only
#
# wan devices configuration
#

menuconfig WAN
	bool "Wan interfaces support"
	help
	  Wide Area Networks (WANs), such as X.25, Frame Relay and leased
	  lines, are used to interconnect Local Area Networks (LANs) over vast
	  distances with data transfer rates significantly higher than those
	  achievable with commonly used asynchronous modem connections.

	  Usually, a quite expensive external device called a `WAN router' is
	  needed to connect to a WAN. As an alternative, a relatively
	  inexpensive WAN interface card can allow your Linux box to directly
	  connect to a WAN.

	  If you have one of those cards and wish to use it under Linux,
	  say Y here and also to the WAN driver for your card.

	  If unsure, say N.

if WAN

# There is no way to detect a comtrol sv11 - force it modular for now.
config HOSTESS_SV11
	tristate "Comtrol Hostess SV-11 support"
	depends on ISA && m && ISA_DMA_API && INET && HDLC && VIRT_TO_BUS
	help
	  Driver for Comtrol Hostess SV-11 network card which
	  operates on low speed synchronous serial links at up to
	  256Kbps, supporting PPP and Cisco HDLC.

	  The driver will be compiled as a module: the
	  module will be called hostess_sv11.

# The COSA/SRP driver has not been tested as non-modular yet.
config COSA
	tristate "COSA/SRP sync serial boards support"
	depends on ISA && m && ISA_DMA_API && HDLC && VIRT_TO_BUS
	help
	  Driver for COSA and SRP synchronous serial boards.

	  These boards allow to connect synchronous serial devices (for example
	  base-band modems, or any other device with the X.21, V.24, V.35 or
	  V.36 interface) to your Linux box. The cards can work as the
	  character device, synchronous PPP network device, or the Cisco HDLC
	  network device.

	  You will need user-space utilities COSA or SRP boards for downloading
	  the firmware to the cards and to set them up. Look at the
	  <http://www.fi.muni.cz/~kas/cosa/> for more information. You can also
	  read the comment at the top of the <file:drivers/net/wan/cosa.c> for
	  details about the cards and the driver itself.

	  The driver will be compiled as a module: the
	  module will be called cosa.

#
# Lan Media's board. Currently 1000, 1200, 5200, 5245
#
config LANMEDIA
	tristate "LanMedia Corp. SSI/V.35, T1/E1, HSSI, T3 boards"
	depends on PCI && VIRT_TO_BUS && HDLC
	help
	  Driver for the following Lan Media family of serial boards:

	  - LMC 1000 board allows you to connect synchronous serial devices
	  (for example base-band modems, or any other device with the X.21,
	  V.24, V.35 or V.36 interface) to your Linux box.

	  - LMC 1200 with on board DSU board allows you to connect your Linux
	  box directly to a T1 or E1 circuit.

	  - LMC 5200 board provides a HSSI interface capable of running up to
	  52 Mbits per second.

	  - LMC 5245 board connects directly to a T3 circuit saving the
	  additional external hardware.

	  To change setting such as clock source you will need lmcctl.
	  It is available at <ftp://ftp.lanmedia.com/> (broken link).

	  To compile this driver as a module, choose M here: the
	  module will be called lmc.

# There is no way to detect a Sealevel board. Force it modular
config SEALEVEL_4021
	tristate "Sealevel Systems 4021 support"
	depends on ISA && m && ISA_DMA_API && INET && HDLC && VIRT_TO_BUS
	help
	  This is a driver for the Sealevel Systems ACB 56 serial I/O adapter.

	  The driver will be compiled as a module: the
	  module will be called sealevel.

# Generic HDLC
config HDLC
	tristate "Generic HDLC layer"
	help
	  Say Y to this option if your Linux box contains a WAN (Wide Area
	  Network) card supported by this driver and you are planning to
	  connect the box to a WAN.

	  You will need supporting software from
	  <http://www.kernel.org/pub/linux/utils/net/hdlc/>.
	  Generic HDLC driver currently supports raw HDLC, Cisco HDLC, Frame
	  Relay, synchronous Point-to-Point Protocol (PPP) and X.25.

	  To compile this driver as a module, choose M here: the
	  module will be called hdlc.

	  If unsure, say N.

config HDLC_RAW
	tristate "Raw HDLC support"
	depends on HDLC
	help
	  Generic HDLC driver supporting raw HDLC over WAN connections.

	  If unsure, say N.

config HDLC_RAW_ETH
	tristate "Raw HDLC Ethernet device support"
	depends on HDLC
	help
	  Generic HDLC driver supporting raw HDLC Ethernet device emulation
	  over WAN connections.

	  You will need it for Ethernet over HDLC bridges.

	  If unsure, say N.

config HDLC_CISCO
	tristate "Cisco HDLC support"
	depends on HDLC
	help
	  Generic HDLC driver supporting Cisco HDLC over WAN connections.

	  If unsure, say N.

config HDLC_FR
	tristate "Frame Relay support"
	depends on HDLC
	help
	  Generic HDLC driver supporting Frame Relay over WAN connections.

	  If unsure, say N.

config HDLC_PPP
	tristate "Synchronous Point-to-Point Protocol (PPP) support"
	depends on HDLC
	help
	  Generic HDLC driver supporting PPP over WAN connections.

	  If unsure, say N.

config HDLC_X25
	tristate "X.25 protocol support"
	depends on HDLC && (LAPB=m && HDLC=m || LAPB=y)
	help
	  Generic HDLC driver supporting X.25 over WAN connections.

	  If unsure, say N.

comment "X.25/LAPB support is disabled"
	depends on HDLC && (LAPB!=m || HDLC!=m) && LAPB!=y

config PCI200SYN
	tristate "Goramo PCI200SYN support"
	depends on HDLC && PCI
	help
	  Driver for PCI200SYN cards by Goramo sp. j.

	  If you have such a card, say Y here and see
	  <http://www.kernel.org/pub/linux/utils/net/hdlc/>.

	  To compile this as a module, choose M here: the
	  module will be called pci200syn.

	  If unsure, say N.

config WANXL
	tristate "SBE Inc. wanXL support"
	depends on HDLC && PCI
	help
	  Driver for wanXL PCI cards by SBE Inc.

	  If you have such a card, say Y here and see
	  <http://www.kernel.org/pub/linux/utils/net/hdlc/>.

	  To compile this as a module, choose M here: the
	  module will be called wanxl.

	  If unsure, say N.

config WANXL_BUILD_FIRMWARE
	bool "rebuild wanXL firmware"
	depends on WANXL && !PREVENT_FIRMWARE_BUILD
	help
	  Allows you to rebuild firmware run by the QUICC processor.
	  It requires m68k toolchains and hexdump programs.

	  You should never need this option, say N.

config PC300TOO
	tristate "Cyclades PC300 RSV/X21 alternative support"
	depends on HDLC && PCI
	help
	  Alternative driver for PC300 RSV/X21 PCI cards made by
	  Cyclades, Inc. If you have such a card, say Y here and see
	  <http://www.kernel.org/pub/linux/utils/net/hdlc/>.

	  To compile this as a module, choose M here: the module
	  will be called pc300too.

	  If unsure, say N here.

config N2
	tristate "SDL RISCom/N2 support"
	depends on HDLC && ISA
	help
	  Driver for RISCom/N2 single or dual channel ISA cards by
	  SDL Communications Inc.

	  If you have such a card, say Y here and see
	  <http://www.kernel.org/pub/linux/utils/net/hdlc/>.

	  Note that N2csu and N2dds cards are not supported by this driver.

	  To compile this driver as a module, choose M here: the module
	  will be called n2.

	  If unsure, say N.

config C101
	tristate "Moxa C101 support"
	depends on HDLC && ISA
	help
	  Driver for C101 SuperSync ISA cards by Moxa Technologies Co., Ltd.

	  If you have such a card, say Y here and see
	  <http://www.kernel.org/pub/linux/utils/net/hdlc/>.

	  To compile this driver as a module, choose M here: the
	  module will be called c101.

	  If unsure, say N.

config FARSYNC
	tristate "FarSync T-Series support"
	depends on HDLC && PCI
	help
	  Support for the FarSync T-Series X.21 (and V.35/V.24) cards by
	  FarSite Communications Ltd.

	  Synchronous communication is supported on all ports at speeds up to
	  8Mb/s (128K on V.24) using synchronous PPP, Cisco HDLC, raw HDLC,
	  Frame Relay or X.25/LAPB.

	  If you want the module to be automatically loaded when the interface
	  is referenced then you should add "alias hdlcX farsync" to a file
	  in /etc/modprobe.d/ for each interface, where X is 0, 1, 2, ..., or
	  simply use "alias hdlc* farsync" to indicate all of them.

	  To compile this driver as a module, choose M here: the
	  module will be called farsync.

config FSL_UCC_HDLC
	tristate "Freescale QUICC Engine HDLC support"
	depends on HDLC
	depends on QUICC_ENGINE
	help
	  Driver for Freescale QUICC Engine HDLC controller. The driver
	  supports HDLC in NMSI and TDM mode.

	  To compile this driver as a module, choose M here: the
	  module will be called fsl_ucc_hdlc.

config SLIC_DS26522
	tristate "Slic Maxim ds26522 card support"
	depends on SPI
	depends on FSL_SOC || ARCH_MXC || ARCH_LAYERSCAPE || COMPILE_TEST
	select BITREVERSE
	help
	  This module initializes and configures the slic maxim card
	  in T1 or E1 mode.

	  To compile this driver as a module, choose M here: the
	  module will be called slic_ds26522.

config IXP4XX_HSS
	tristate "Intel IXP4xx HSS (synchronous serial port) support"
	depends on HDLC && IXP4XX_NPE && IXP4XX_QMGR
	depends on ARCH_IXP4XX && OF
	select MFD_SYSCON
	help
	  Say Y here if you want to use built-in HSS ports
	  on IXP4xx processor.

# X.25 network drivers
config LAPBETHER
	tristate "LAPB over Ethernet driver"
	depends on LAPB && X25
	help
	  Driver for a pseudo device (typically called /dev/lapb0) which allows
	  you to open an LAPB point-to-point connection to some other computer
	  on your Ethernet network.

	  In order to do this, you need to say Y or M to the driver for your
	  Ethernet card as well as to "LAPB Data Link Driver".

	  To compile this driver as a module, choose M here: the
	  module will be called lapbether.


	  If unsure, say N.

endif # WAN