1# $NetBSD: GENERIC,v 1.226 2011/01/17 13:43:02 jdc Exp $ 2# 3# GENERIC machine description file 4# 5# This machine description file is used to generate the default NetBSD 6# kernel. The generic kernel does not include all options, subsystems 7# and device drivers, but should be useful for most applications. 8# 9# The machine description file can be customised for your specific 10# machine to reduce the kernel size and improve its performance. 11# 12# For further information on compiling NetBSD kernels, see the config(8) 13# man page. 14# 15# For further information on hardware support for this architecture, see 16# the intro(4) man page. For further information about kernel options 17# for this architecture, see the options(4) man page. For an explanation 18# of each device driver in this file see the section 4 man page for the 19# device. 20 21include "arch/sparc/conf/std.sparc" 22 23options INCLUDE_CONFIG_FILE # embed config file in kernel binary 24 25#ident "GENERIC-$Revision: 1.226 $" 26 27maxusers 32 28 29## System kernel configuration. See options(4) for more detail. 30 31 32# Options for variants of the Sun SPARC architecure. 33# We currently support three architecture types; at least one is required. 34options SUN4 # sun4/100, sun4/200, sun4/300 35options SUN4C # sun4c - SS1, 1+, 2, ELC, SLC, IPC, IPX, etc. 36options SUN4M # sun4m - SS10, SS20, Classic, etc. 37options SUN4D # sun4d - SS1000, SC2000 38 39options SUN4_MMU3L # sun4/400 3-level MMU 40 41## System options specific to the sparc machine type 42 43# Blink the power LED on some machines to indicate the system load. 44#options BLINK 45 46## Use a faster console than the PROM's slow drawing routines. Not needed 47## for headless (no framebuffer) machines. 48## These is obsolete for wscons kernels 49#options RASTERCONSOLE # fast rasterop console 50#options RASTERCONSOLE_FGCOL=WSCOL_BLACK 51#options RASTERCONSOLE_BGCOL=WSCOL_WHITE 52 53# wscons stuff 54options WSEMUL_SUN 55#options WSEMUL_VT100 56options WSDISPLAY_COMPAT_RAWKBD 57options WSDISPLAY_CUSTOM_OUTPUT 58options WS_DEFAULT_FG=WSCOL_BLACK 59options WS_DEFAULT_BG=WSCOL_LIGHT_WHITE 60options WS_KERNEL_FG=WSCOL_GREEN 61options WS_KERNEL_BG=WSCOL_LIGHT_WHITE 62options WSDISPLAY_COMPAT_PCVT 63options WSDISPLAY_COMPAT_SYSCONS 64options WSDISPLAY_COMPAT_USL 65 66options WSDISPLAY_SCROLLSUPPORT 67 68# generic options vlid for both wscons and RASTERCONSOLE 69options FONT_GALLANT12x22 # the console font 70#options FONT_BOLD8x16 # a somewhat smaller font 71 72#### System options that are the same for all ports 73 74## Root device configuration: change the ?'s if you are going to use a 75## nonstandard root partition (other than where the kernel is booted from) 76## and/or nonstandard root type (not ffs or nfs). Normally this can be 77## automagically determined at boot time. 78 79config netbsd root on ? type ? 80 81## System call tracing (see ktrace(1)). 82options KTRACE 83 84## Collect statistics on kernel malloc's and free's. This does have a 85## significant performance hit on slower machines, so it is intended for 86## diagnostic use only. 87#options KMEMSTATS 88 89## System V compatible IPC subsystem. (msgctl(2), semctl(2), and shmctl(2)) 90options SYSVMSG # System V message queues 91options SYSVSEM # System V semaphores 92options SYSVSHM # System V shared memory 93options P1003_1B_SEMAPHORE # p1003.1b semaphore support 94 95## Loadable kernel module support; still under development. 96 97options USERCONF # userconf(4) support 98#options PIPE_SOCKETPAIR # smaller, but slower pipe(2) 99options SYSCTL_INCLUDE_DESCR # Include sysctl descriptions in kernel 100 101# Enable experimental buffer queue strategy for better responsiveness under 102# high disk I/O load. Use it with caution - it's not proven to be stable yet. 103#options BUFQ_READPRIO 104#options BUFQ_PRIOCSCAN 105 106## NFS boot options; tries DHCP/BOOTP then BOOTPARAM 107options NFS_BOOT_BOOTPARAM 108#options NFS_BOOT_BOOTP 109options NFS_BOOT_DHCP 110 111#### Debugging options 112 113## The DDB in-kernel debugger runs at panic (unless DDB_ONPANIC=0), or at 114## serial console break or keyboard reset, where the PROM would normally 115## intercept. DDB_HISTORY_SIZE adds up/down arrow command history. 116options DDB # kernel dynamic debugger 117options DDB_HISTORY_SIZE=100 # enable history editing in DDB 118#options DDB_ONPANIC=1 # see also sysctl(8): `ddb.onpanic' 119 120## You may also use gdb, on another computer connected to this machine over 121## a serial port. Both KGDB_DEV and KGDB_DEVRATE should be specified; 122## KGDB_DEV is a dev_t encoded device number of the serial port to use, where 123## the minor device number encodes the PROM enumeration of the serial ports, 124## i.e.: 125## 0xc00 = ttya, 0xc01 = ttyb, 0xc02 = ttyc, 0xc03 = ttyd. 126## (Note: ttyc and ttyd are available only on some sun4 models) 127#options KGDB # support for kernel gdb 128#options KGDB_DEV=0xc01 # kgdb device number (this is `ttyb') 129#options KGDB_DEVRATE=38400 # baud rate 130 131 132## Compile the kernel with debugging symbols (`netbsd.gdb' is the debug file), 133## such that gdb(1) can be used on a kernel coredump. 134 135#makeoptions DEBUG="-g" 136 137 138## Adds code to the kernel that does internal consistency checks, and will 139## cause the kernel to panic if corruption of internal data structures 140## is detected. 141#options DIAGNOSTIC # extra kernel sanity checking 142 143## Enable (possibly expensive) debugging code that may also display messages 144## on the system console 145#options DEBUG 146#options LOCKDEBUG 147#options SYSCALL_DEBUG 148 149## Make SCSI error messages more verbose when explaining their meanings. 150options SCSIVERBOSE 151 152options MIIVERBOSE # verbose PHY autoconfig messages 153 154## `INSECURE' turns off the kernel security level (securelevel = 0 always). 155## This allows writing to /dev/mem, loading kernel modules while multi-user, 156## and other insecurities good only for development work. Do not use this 157## option on a production machine. 158#options INSECURE 159 160## `FDSCRIPTS' allows non-readable but executable scripts by providing a 161## pre-opened opaque file to the script interpreter. `SETUIDSCRIPTS', 162## which implies FDSCRIPTS, allows scripts to be set-user-id using the same 163## opaque file mechanism. Perl calls this "secure setuid scripts." 164 165#options FDSCRIPTS 166#options SETUIDSCRIPTS 167 168## Options for compatibility with previous releases foreign system binaries. 169## In the cases of COMPAT_SUNOS and COMPAT_SVR4, you may need to set up 170## additional user-level utilities or system configuration files. See 171## compat_sunos(8) and compat_svr4(8). 172 173options COMPAT_43 # 4.3BSD system interfaces 174options COMPAT_10 # NetBSD 1.0 binary compatibility 175options COMPAT_11 # NetBSD 1.1 binary compatibility 176options COMPAT_12 # NetBSD 1.2 binary compatibility 177options COMPAT_13 # NetBSD 1.3 binary compatibility 178options COMPAT_14 # NetBSD 1.4 binary compatibility 179options COMPAT_15 # NetBSD 1.5 binary compatibility 180options COMPAT_16 # NetBSD 1.6 binary compatibility 181options COMPAT_20 # NetBSD 2.0 binary compatibility 182options COMPAT_30 # NetBSD 3.0 binary compatibility 183options COMPAT_40 # NetBSD 4.0 binary compatibility 184options COMPAT_50 # NetBSD 5.0 binary compatibility 185options COMPAT_SUNOS # SunOS 4.x binary compatibility 186options COMPAT_SVR4 # SunOS 5.x binary compatibility 187options COMPAT_BSDPTY # /dev/[pt]ty?? ptys. 188 189## File systems. You probably need at least one of FFS or NFS. 190file-system FFS # Berkeley Fast Filesystem 191file-system NFS # Sun NFS-compatible filesystem client 192file-system KERNFS # kernel data-structure filesystem 193file-system NULLFS # NULL layered filesystem 194file-system OVERLAY # overlay file system 195file-system MFS # memory-based filesystem 196file-system FDESC # user file descriptor filesystem 197file-system UMAPFS # uid/gid remapping filesystem 198file-system LFS # Log-based filesystem (still experimental) 199file-system PUFFS # Userspace file systems (e.g. ntfs-3g & sshfs) 200file-system PROCFS # /proc 201file-system CD9660 # ISO 9660 + Rock Ridge file system 202file-system UNION # union file system 203file-system MSDOSFS # MS-DOS FAT filesystem(s). 204file-system CODA # Coda File System; also needs vcoda (below) 205file-system PTYFS # /dev/pts/N support 206file-system TMPFS # Efficient memory file-system 207#file-system UDF # experimental - OSTA UDF CD/DVD file-system 208 209## File system options. 210options NFSSERVER # Sun NFS-compatible filesystem server 211options QUOTA # FFS quotas 212#options FFS_EI # FFS Endian Independent support 213options WAPBL # File system journaling support - Experimental 214#options UFS_DIRHASH # UFS Large Directory Hashing - Experimental 215#options FFS_NO_SNAPSHOT # No FFS snapshot support 216 217## Network protocol support. In most environments, INET is required. 218options INET # IP (Internet Protocol) v4 219options INET6 # IPV6 220#options IPSEC # IP security 221#options IPSEC_ESP # IP security (encryption part; define w/IPSEC) 222#options IPSEC_NAT_T # IPsec NAT traversal (NAT-T) 223#options IPSEC_DEBUG # debug for IP security 224#options GATEWAY # packet forwarding ("router switch") 225#options MROUTING # packet forwarding of multicast packets 226#options PIM # Protocol Independent Multicast 227#options DIRECTED_BROADCAST # allow broadcasts through routers 228#options ISO,TPIP # OSI networking 229#options EON # OSI tunneling over IP 230#options NETATALK # AppleTalk (over Ethernet) protocol 231options NTP # Network Time Protocol in-kernel support 232#options PPS_SYNC # Add serial line synchronization for NTP 233options PFIL_HOOKS # Add pfil(9) hooks, intended for custom LKMs. 234options IPFILTER_LOG # Add ipmon(8) logging for ipfilter device 235options IPFILTER_LOOKUP # ippool(8) support 236options IPFILTER_COMPAT # Compat for IP-Filter 237#options IPFILTER_DEFAULT_BLOCK # block all packets by default 238options PPP_BSDCOMP # Add BSD compression to ppp device 239options PPP_DEFLATE # Add deflate (libz) compression to ppp device 240options PPP_FILTER # Add active filters for ppp (via bpf) 241 242#options ALTQ # Manipulate network interfaces' output queues 243#options ALTQ_BLUE # Stochastic Fair Blue 244#options ALTQ_CBQ # Class-Based Queueing 245#options ALTQ_CDNR # Diffserv Traffic Conditioner 246#options ALTQ_FIFOQ # First-In First-Out Queue 247#options ALTQ_FLOWVALVE # RED/flow-valve (red-penalty-box) 248#options ALTQ_HFSC # Hierarchical Fair Service Curve 249#options ALTQ_LOCALQ # Local queueing discipline 250#options ALTQ_PRIQ # Priority Queueing 251#options ALTQ_RED # Random Early Detection 252#options ALTQ_RIO # RED with IN/OUT 253#options ALTQ_WFQ # Weighted Fair Queueing 254 255 256 257#### Main bus and CPU .. all systems. 258mainbus0 at root 259cpu0 at mainbus0 260cpuunit0 at mainbus0 # sun4d 261cpuunit* at mainbus0 # sun4d 262cpu0 at cpuunit0 # sun4d 263 264#### Bus types found on SPARC systems. 265 266sbus0 at mainbus0 # sun4c 267obio0 at mainbus0 # sun4 and sun4m 268sparcvme0 at mainbus0 # sun4 269iommu0 at mainbus0 # sun4m 270sbus0 at iommu0 # sun4m 271sparcvme0 at iommu0 # sun4m 272vme0 at sparcvme0 # MI VME attachment 273bootbus0 at cpuunit0 # sun4d 274bootbus* at cpuunit? # sun4d 275 276## SBus expander box 277xbox* at sbus? slot ? offset ? 278sbus* at xbox? 279 280## SBus to PCMCIA bridge 281nell* at sbus? slot ? offset ? # PCMCIA bridge 282pcmcia* at nell? 283tslot* at sbus? slot ? offset ? # PCMCIA bridge (tadpole 3gx) 284pcmcia* at tslot? 285 286#### Standard system devices -- all required for a given architecture 287 288## Auxiliary system registers on sun4c and sun4m 289auxreg0 at mainbus0 # sun4c 290auxreg0 at obio0 # sun4m 291auxiotwo0 at obio0 # only on Tadpole SPARCbook. 292 293## Power status and control register on Sun4m systems 294power0 at obio0 295 296## Mostek clock found on 4/300, sun4c, sun4m and sun4d systems. 297## The Mostek clock NVRAM is the "eeprom" on sun4/300 systems. 298clock0 at mainbus0 # sun4c 299clock0 at obio0 # sun4m 300clock0 at obio0 addr 0xf2000000 # sun4/300 301clock0 at bootbus0 # sun4d 302 303## Intersil clock found on 4/100 and 4/200 systems. 304oclock0 at obio0 addr 0xf3000000 # sun4/200 305oclock0 at obio0 addr 0x03000000 # sun4/100 306 307## Memory error registers. 308memreg0 at mainbus0 # sun4c 309memreg0 at obio0 # sun4m 310memreg0 at obio0 addr 0xf4000000 # sun4/200 and sun4/300 311memreg0 at obio0 addr 0x04000000 # sun4/100 312 313## ECC memory control 314eccmemctl0 at mainbus0 # sun4m 315 316## Timer chip found on 4/300, sun4c, and sun4m systems. 317timer0 at mainbus0 # sun4c 318timer0 at obio0 # sun4m 319timer0 at obio0 addr 0xef000000 # sun4/300 320 321## EEPROM found on 4/100 and 4/200 systems. Note that the 4/300 322## doesn't use this driver; the `EEPROM' is in the NVRAM on the 323## Mostek clock chip on 4/300 systems. 324eeprom0 at obio0 addr 0xf2000000 # sun4/200 325eeprom0 at obio0 addr 0x02000000 # sun4/100 326 327 328#### Serial port configuration 329 330## Zilog 8530 serial chips. Each has two-channels. 331## zs0 is ttya and ttyb. zs1 is the keyboard and mouse. 332zs0 at mainbus0 # sun4c 333zs0 at obio0 # sun4m 334zs0 at obio0 addr 0xf1000000 level 12 # sun4/200 and sun4/300 335zs0 at obio0 addr 0x01000000 level 12 # sun4/100 336zs0 at bootbus0 # sun4d 337zstty0 at zs0 channel 0 # ttya 338zstty1 at zs0 channel 1 # ttyb 339 340zs1 at mainbus0 # sun4c 341zs1 at obio0 # sun4m 342zs1 at obio0 addr 0xf0000000 level 12 # sun4/200 and sun4/300 343zs1 at obio0 addr 0x00000000 level 12 # sun4/100 344zs1 at bootbus0 # sun4d 345 346# old kbd and mouse attachments 347#kbd0 at zs1 channel 0 # keyboard 348#ms0 at zs1 channel 1 # mouse 349zstty* at zs? 350 351# these are for wscons 352kbd0 at zstty? 353ms0 at zstty? 354wskbd* at wskbddev? 355wsmouse* at wsmousedev? 356 357zs2 at obio0 addr 0xe0000000 level 12 # sun4/300 358zstty2 at zs2 channel 0 # ttyc 359zstty3 at zs2 channel 1 # ttyd 360 361zs* at bootbus? # sun4d 362zstty* at zs? 363 364## NS16x50 serial chips and clones. Present on the 365## Sun JavaStation-1 and Tadpole SPARCbook 3 366com* at obio0 # sun4m 367 368# Parallel port. 369bpp* at sbus? slot? offset ? 370 371## Magma Serial/Parallel driver 372magma* at sbus? slot ? offset ? 373mtty* at magma? 374mbpp* at magma? 375 376## SUNW,spif Serial/Parallel driver 377spif* at sbus? slot ? offset ? 378stty* at spif? 379sbpp* at spif? 380 381## PCMCIA serial interfaces 382#com* at pcmcia? 383#pcmcom* at pcmcia? 384#com* at pcmcom? 385 386#### Disk controllers and disks 387 388# 389 390## The following flags may be set for the NCR53c94 based esp driver: 391## bits 0-7: disable disconnect/reselect for the corresponding target 392## bits 8-15: disable synchronous negotiation for target [bit-8] 393 394## sun4/300, sun4c, sun4m on-board SCSI, and FSBE/S SBus SCSI cards. 395## Both `dma' and `esp' are needed in all cases. 396## Two kinds of additional SBus SCSI interfaces are available. One uses 397## "esp at sbus" like the sun4c on-board; the other uses "esp at dma". 398 399## sun4/300 SCSI - an NCR53c94 or equivalent behind 400## an LSI Logic DMA controller 401 402dma0 at obio0 addr 0xfa001000 level 4 # sun4/300 403esp0 at obio0 addr 0xfa000000 level 4 flags 0x0000 # sun4/300 404 405dma0 at sbus0 slot ? offset ? # sun4c/sun4m 406esp0 at sbus0 slot ? offset ? flags 0x0000 # sun4c 407esp0 at dma0 flags 0x0000 # sun4m 408 409# FSBE/S SCSI & SunSwift Sbus FAS366 410dma* at sbus? slot ? offset ? # SBus 411esp* at sbus? slot ? offset ? flags 0x0000 # SBus 412esp* at dma? flags 0x0000 # SBus 413 414scsibus* at esp? 415 416## Qlogic ISP SBus SCSI Card 417isp* at sbus? slot ? offset ? 418scsibus* at isp? 419 420## NCR5380-based "Sun SCSI 3" VME SCSI controller. 421## This driver has several flags which may be enabled by OR'ing 422## the values and using the "flags" directive. 423## Valid flags are: 424## 425## 0x01 Use DMA (may be polled) 426## 0x02 Use DMA completion interrupts 427## 0x04 Allow disconnect/reselect 428## 429## E.g. the following would enable DMA, interrupts, and reselect: 430## si0 at vme0 addr 0x200000 irq 3 vect 0x40 flags 0x07 431## 432## By default, DMA is enabled in the driver. 433 434si0 at vme0 addr 0x200000 irq 2 vect 0x40 435scsibus* at si? 436 437## NCR5380-based "SCSI Weird" on-board SCSI interface found 438## on sun4/100 systems. The flags are the same as the "si" 439## controller. Note, while DMA is enabled by default, only 440## polled DMA works at this time, and reselects do not work 441## on this particular controller. 442 443sw0 at obio0 addr 0x0a000000 level 3 444scsibus* at sw? 445 446## PCMCIA SCSI controllers 447#aic* at pcmcia? 448#spc* at pcmcia? 449#scsibus* at aic? 450#scsibus* at spc? 451 452 453## These entries find devices on all SCSI busses and assign 454## unit numbers dynamically. 455sd* at scsibus? target ? lun ? # SCSI disks 456st* at scsibus? target ? lun ? # SCSI tapes 457cd* at scsibus? target ? lun ? # SCSI CD-ROMs 458ch* at scsibus? target ? lun ? # SCSI changer devices 459ss* at scsibus? target ? lun ? # SCSI scanners 460ses* at scsibus? target ? lun ? # SCSI SES/SAF-TE 461uk* at scsibus? target ? lun ? # unknown SCSI 462 463 464## Xylogics 753 or 7053 VME SMD disk controllers and disks, found 465## on sun4 systems. 466xdc0 at vme0 addr 0xee80 irq 3 vect 0x44 467xdc1 at vme0 addr 0xee90 irq 3 vect 0x45 468xdc2 at vme0 addr 0xeea0 irq 3 vect 0x46 469xdc3 at vme0 addr 0xeeb0 irq 3 vect 0x47 470xd* at xdc? drive ? 471 472## Xylogics 451 or 451 VME SMD disk controllers and disks, found 473## on sun4 systems. 474xyc0 at vme0 addr 0xee40 irq 3 vect 0x48 475xyc1 at vme0 addr 0xee48 irq 3 vect 0x49 476xy* at xyc? drive ? 477 478 479## Floppy controller and drive found on SPARCstations. 480 481fdc0 at mainbus0 # sun4c controller 482fdc0 at obio0 # sun4m controller 483fd* at fdc0 # the drive itself 484 485## PCMCIA IDE controllers 486#wdc* at pcmcia? 487#atabus* at ata? 488#wd* at atabus? drive ? flags 0x0000 489 490## A disk-like interface to files. Can be used to create floppy, CD, 491## miniroot images, etc. 492 493pseudo-device vnd 494#options VND_COMPRESSION # compressed vnd(4) 495 496## Concatenated and striped disks; with this, you can create a software-based 497## disk array similar to a "RAID 0" setup. See ccd(4). 498 499pseudo-device ccd 4 500 501## Cryptographic disk devices; See cgd(4) 502 503#pseudo-device cgd 4 504 505## RAIDframe disk driver: software RAID driver. See raid(4). 506 507pseudo-device raid 8 508options RAID_AUTOCONFIG # auto-configuration of RAID components 509# Options to enable various other RAIDframe RAID types. 510# options RF_INCLUDE_EVENODD=1 511# options RF_INCLUDE_RAID5_RS=1 512# options RF_INCLUDE_PARITYLOGGING=1 513# options RF_INCLUDE_CHAINDECLUSTER=1 514# options RF_INCLUDE_INTERDECLUSTER=1 515# options RF_INCLUDE_PARITY_DECLUSTERING=1 516# options RF_INCLUDE_PARITY_DECLUSTERING_DS=1 517 518 519## Memory disk device, used on boot floppies with compressed 520## kernel-plus-root-disk images. 521 522#pseudo-device md 523 524 525#### Network interfaces 526 527## LANCE Ethernet - an AMD 7990 LANCE behind specialized DMA glue 528## Three flavors of additional SBus ethernets are available. One attaches 529## directly like the sun4c on-board, one uses the ledma device like the 530## sun4m on-board, and one uses the lebuffer device. 531 532le0 at obio0 addr 0xf9000000 level 6 # sun4/300 533le0 at sbus0 slot ? offset ? # sun4c on-board 534ledma0 at sbus0 slot ? offset ? # sun4m on-board 535le0 at ledma0 # sun4m on-board 536le* at sbus? slot ? offset ? # SBus 537ledma* at sbus? slot ? offset ? # SBus 538le* at ledma? # SBus 539lebuffer0 at sbus? slot ? offset ? # SBus 540le0 at lebuffer? # SBus 541lebuffer* at sbus? slot ? offset ? # SBus 542le* at lebuffer? # SBus 543 544 545## sun4/100 and sun4/200 Ethernet - an Intel 82586 on-board 546## or on a Multibus/VME card. 547ie0 at obio0 addr 0xf6000000 level 6 # sun4/200 on-board 548ie0 at obio0 addr 0x06000000 level 6 # sun4/100 on-board 549## VME: the first [addr,len] pair specifies the device registers; 550## the second pair specifies the on-board memory buffer 551ie1 at vme0 addr 0xe88000,0xe00000 len -1,0x40000 irq 3 vect 0x75 552ie2 at vme0 addr 0x31ff02,0x300000 len -1,0x40000 irq 3 vect 0x76 553ie3 at vme0 addr 0x35ff02,0x300000 len -1,0x40000 irq 3 vect 0x77 554ie4 at vme0 addr 0x2dff02,0x200000 len -1,0x40000 irq 3 vect 0x7c 555 556## Quad Ethernet Controller with BigMac (be, 10/100MBd) and Mace Ethernet 557## (qe, 10MBd) attached. 558qec* at sbus? slot ? offset ? # Quad Ethernet Controller 559be* at qec? # BigMac Ethernet (10/100MBd) 560qe* at qec? # Mace Ethernet (10MBd) 561 562## Happy Meal Ethernet 563hme* at sbus? slot ? offset ? 564 565# midway ATM 566en0 at sbus? slot ? offset ? 567 568# PCMCIA ethernet devices 569#ep* at pcmcia? 570#mbe* at pcmcia? 571#ne* at pcmcia? 572#sm* at pcmcia? 573 574## PCMCIA wavelan card 575#wi* at pcmcia? function ? # Lucent WaveLan IEEE (802.11) 576 577# MII/PHY support 578exphy* at mii? phy ? # 3Com internal PHYs 579icsphy* at mii? phy ? # Integrated Circuit Systems ICS189x 580inphy* at mii? phy ? # Intel 82555 PHYs 581lxtphy* at mii? phy ? # Level One LXT-970 PHYs 582nsphy* at mii? phy ? # NS83840 PHYs 583qsphy* at mii? phy ? # Quality Semiconductor QS6612 PHYs 584sqphy* at mii? phy ? # Seeq 80220/80221/80223 PHYs 585tlphy* at mii? phy ? # ThunderLAN PHYs 586ukphy* at mii? phy ? # generic unknown PHYs 587 588## Loopback network interface; required 589pseudo-device loop 590 591## SLIP and CSLIP interfaces, for IP over a serial line. 592pseudo-device sl 593 594## PPP, the successor to SLIP. See pppd(8). 595pseudo-device ppp 596 597## PPP over Ethernet (RFC 2516) 598pseudo-device pppoe 599 600## Starmode Radio IP, a special hardware network device. 601#pseudo-device strip 602 603## Network "tunnel" device, allowing protocol stacks to run in the userland. 604## This is used by the third-party user-mode "ppp" program, and others. 605pseudo-device tun 606pseudo-device tap # virtual Ethernet 607 608## Generic L3 over IP tunnel 609#pseudo-device gre # generic L3 over IP tunnel 610 611## Berkeley Packet Filter, required to run RARPD. A generic C-language 612## interface that allows selective examining of incoming packets. 613pseudo-device bpfilter 614 615#pseudo-device carp # Common Address Redundancy Protocol 616 617## IP Filter, used in firewall and NAT applications. See ipnat(8) for 618## one example of the use of the IP Filter. 619pseudo-device ipfilter 620 621## for IPv6 622pseudo-device gif # IPv[46] over IPv[46] tunnel (RFC1933) 623#pseudo-device faith # IPv[46] tcp relay translation i/f 624pseudo-device stf # 6to4 IPv6 over IPv4 encapsulation 625 626## IEEE 802.1Q Virtual LAN encapsulation, see vlan(4). 627pseudo-device vlan 628 629## Simple inter-network traffic bridging 630pseudo-device bridge 631#options BRIDGE_IPF # bridge uses IP/IPv6 pfil hooks too 632pseudo-device agr # IEEE 802.3ad link aggregation 633 634## accept filters 635pseudo-device accf_data # "dataready" accept filter 636pseudo-device accf_http # "httpready" accept filter 637 638#### Audio and video devices 639 640## /dev/audio support (`audioamd' plus `audio') 641## 642audioamd0 at mainbus0 # sun4c 643audioamd0 at obio0 # sun4m 644audioamd0 at sbus0 slot ? offset ? # sun4m 645 646audiocs0 at sbus0 slot ? offset ? # SUNW,CS4231 647 648#options DBRI_DEBUG # noisy debug output from the dbri driver 649#options DBRI_BIG_BUFFER # use bigger DMA buffers, for slow CPUs 650dbri* at sbus? slot ? offset ? # SUNW,DBRI[s3|e] 651 652audio* at audiobus? 653 654## Sun "bwtwo" black and white framebuffer, found on sun4, sun4c, and sun4m 655## systems. If your sun4 system has a cgfour installed in the P4 slot, 656## the P4 entries for "bwtwo" will attach to the overlay plane of the 657## "cgfour". 658 659bwtwo0 at sbus0 slot ? offset ? # sun4c and sun4m 660bwtwo* at sbus? slot ? offset ? # 661bwtwo0 at obio0 addr 0xfd000000 level 4 # sun4/200 662bwtwo0 at obio0 addr 0xfb300000 level 4 # sun4/300 in P4 slot 663bwtwo0 at obio0 addr 0x0b300000 level 4 # sun4/100 in P4 slot 664 665## Sun "cgtwo" VME color framebuffer 666# XXX no wsdisplay support 667#cgtwo0 at vme0 addr 0x400000 irq ? vect 0xa8 668 669## Sun "cgthree" Sbus color framebuffer 670cgthree0 at sbus? slot ? offset ? 671cgthree* at sbus? slot ? offset ? 672 673## Sun "cgfour" color framebuffer with overlay plane. See above comment 674## regarding overlay plane. 675# XXX no wsdisplay support 676#cgfour0 at obio0 addr 0xfb300000 level 4 # sun4/300 P4 677#cgfour0 at obio0 addr 0x0b300000 level 4 # sun4/100 P4 678 679## Sun "cgsix" accelerated color framebuffer. 680cgsix0 at sbus? slot ? offset ? 681cgsix* at sbus? slot ? offset ? 682cgsix0 at obio0 addr 0xfb000000 level 4 # sun4/300 P4 683cgsix0 at obio0 addr 0x0b000000 level 4 # sun4/100 P4 684 685## Sun "cgeight" 24-bit framebuffer 686# XXX no wsdisplay support 687#cgeight0 at obio0 addr 0xfb300000 level 4 # sun4/300 P4 688#cgeight0 at obio0 addr 0x0b300000 level 4 # sun4/100 P4 689 690## Sun "tcx" accelerated color framebuffer. 691# there can be only one 692tcx0 at sbus? slot ? offset ? 693 694## Sun CG12 / Matrox SG3 accelerated 24bit framebuffer 695## runs monochrome only for now 696cgtwelve* at sbus? slot ? offset ? 697 698# Sun "cgfourteen" accelerated 24-bit framebuffer. 699cgfourteen* at obio0 # sun4m 700 701# P9100-based display on Tadpole SPARCbook 3. 702pnozz0 at sbus? slot ? offset ? 703# the SPARCbook 3 hardware docs say that accesses to P9100 registers need to be 704# 'latched in' but at least my 3GX works happily without 705# Enable it by default since we don't know which hardware really needs it. 706options PNOZZ_USE_LATCH 707 708# Sun ZX/Leo 24-bit framebuffer 709zx* at sbus? slot ? offset ? 710 711# Fujitsu AG-10e accelerated graphics 8/24-bit board 712agten* at sbus? slot ? offset ? 713 714# generic framebuffer console 715genfb* at sbus? slot ? offset ? 716 717# make sure wsdisplay0 is the console 718wsdisplay0 at wsemuldisplaydev? console 1 719wsdisplay* at wsemuldisplaydev? 720 721#### Other device configuration 722 723# Tadpole microcontroller 724tctrl0 at obio0 725 726# Aurora Personality Chip (APC) on SPARCstation-4/5 727# Not enabled by default as it may hang some systems 728#apc* at sbus? slot ? offset ? 729 730## Pseudo ttys, required for network logins and programs like screen. 731 732pseudo-device pty # pseudo-terminals 733 734## Random device, used to implement /dev/random (a source of random noise), 735## and generate randomness for some kernel formulae. 736 737pseudo-device rnd 738 739# a pseudo device needed for Coda # also needs CODA (above) 740pseudo-device vcoda 4 # coda minicache <-> venus comm. 741 742pseudo-device clockctl # user control of clock subsystem 743pseudo-device ksyms # /dev/ksyms 744#pseudo-device pf # PF packet filter 745#pseudo-device pflog # PF log if 746pseudo-device fss # file system snapshot device 747pseudo-device wsmux # mouse and keyboard multiplexor 748pseudo-device wsfont 749pseudo-device putter # for puffs and pud 750 751#options FILEASSOC # fileassoc(9) 752 753# Veriexec 754# 755# a pseudo device needed for veriexec 756#pseudo-device veriexec 1 757# 758# Uncomment the fingerprint methods below that are desired. Note that 759# removing fingerprint methods will have almost no impact on the kernel 760# code size. 761# 762#options VERIFIED_EXEC_FP_RMD160 763#options VERIFIED_EXEC_FP_SHA256 764#options VERIFIED_EXEC_FP_SHA384 765#options VERIFIED_EXEC_FP_SHA512 766#options VERIFIED_EXEC_FP_SHA1 767#options VERIFIED_EXEC_FP_MD5 768 769#options PAX_MPROTECT=0 # PaX mprotect(2) restrictions 770 # (for static binaries only for now) 771