1/* $NetBSD: aic79xx.reg,v 1.12 2006/02/25 00:58:35 wiz Exp $ */ 2 3/* 4 * Aic79xx register and scratch ram definitions. 5 * 6 * Copyright (c) 1994-2001 Justin T. Gibbs. 7 * Copyright (c) 2000-2002 Adaptec Inc. 8 * All rights reserved. 9 * 10 * Redistribution and use in source and binary forms, with or without 11 * modification, are permitted provided that the following conditions 12 * are met: 13 * 1. Redistributions of source code must retain the above copyright 14 * notice, this list of conditions, and the following disclaimer, 15 * without modification. 16 * 2. Redistributions in binary form must reproduce at minimum a disclaimer 17 * substantially similar to the "NO WARRANTY" disclaimer below 18 * ("Disclaimer") and any redistribution must be conditioned upon 19 * including a substantially similar Disclaimer requirement for further 20 * binary redistribution. 21 * 3. Neither the names of the above-listed copyright holders nor the names 22 * of any contributors may be used to endorse or promote products derived 23 * from this software without specific prior written permission. 24 * 25 * Alternatively, this software may be distributed under the terms of the 26 * GNU General Public License ("GPL") version 2 as published by the Free 27 * Software Foundation. 28 * 29 * NO WARRANTY 30 * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS 31 * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT 32 * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTIBILITY AND FITNESS FOR 33 * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT 34 * HOLDERS OR CONTRIBUTORS BE LIABLE FOR SPECIAL, EXEMPLARY, OR CONSEQUENTIAL 35 * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS 36 * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) 37 * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, 38 * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING 39 * IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE 40 * POSSIBILITY OF SUCH DAMAGES. 41 * 42 * $FreeBSD: src/sys/dev/aic7xxx/aic79xx.reg,v 1.15 2003/06/10 03:25:24 gibbs Exp $ 43 */ 44VERSION = "Id: //depot/aic7xxx/aic7xxx/aic79xx.reg#70 $" 45 46/* 47 * This file is processed by the aic7xxx_asm utility for use in assembling 48 * firmware for the aic79xx family of SCSI host adapters as well as to generate 49 * a C header file for use in the kernel portion of the Aic79xx driver. 50 */ 51 52/* Register window Modes */ 53#define M_DFF0 0 54#define M_DFF1 1 55#define M_CCHAN 2 56#define M_SCSI 3 57#define M_CFG 4 58#define M_DST_SHIFT 4 59 60#define MK_MODE(src, dst) ((src) | ((dst) << M_DST_SHIFT)) 61#define SET_MODE(src, dst) \ 62 SET_SRC_MODE src; \ 63 SET_DST_MODE dst; \ 64 if ((ahd->bugs & AHD_SET_MODE_BUG) != 0) { \ 65 mvi MK_MODE(src, dst) call set_mode_work_around; \ 66 } else { \ 67 mvi MODE_PTR, MK_MODE(src, dst); \ 68 } 69 70#define TOGGLE_DFF_MODE \ 71 if ((ahd->bugs & AHD_SET_MODE_BUG) != 0) { \ 72 call toggle_dff_mode_work_around; \ 73 } else { \ 74 xor MODE_PTR, MK_MODE(M_DFF1, M_DFF1); \ 75 } 76 77#define RESTORE_MODE(mode) \ 78 if ((ahd->bugs & AHD_SET_MODE_BUG) != 0) { \ 79 mov mode call set_mode_work_around; \ 80 } else { \ 81 mov MODE_PTR, mode; \ 82 } 83 84#define SET_SEQINTCODE(code) \ 85 if ((ahd->bugs & AHD_INTCOLLISION_BUG) != 0) { \ 86 mvi code call set_seqint_work_around; \ 87 } else { \ 88 mvi SEQINTCODE, code; \ 89 } 90 91/* 92 * Mode Pointer 93 * Controls which of the 5, 512byte, address spaces should be used 94 * as the source and destination of any register accesses in our 95 * register window. 96 */ 97register MODE_PTR { 98 address 0x000 99 access_mode RW 100 field DST_MODE 0x70 101 field SRC_MODE 0x07 102 mode_pointer 103} 104 105const SRC_MODE_SHIFT 0 106const DST_MODE_SHIFT 4 107 108/* 109 * Host Interrupt Status 110 */ 111register INTSTAT { 112 address 0x001 113 access_mode RW 114 field HWERRINT 0x80 115 field BRKADRINT 0x40 116 field SWTMINT 0x20 117 field PCIINT 0x10 118 field SCSIINT 0x08 119 field SEQINT 0x04 120 field CMDCMPLT 0x02 121 field SPLTINT 0x01 122 mask INT_PEND 0xFF 123} 124 125/* 126 * Sequencer Interrupt Code 127 */ 128register SEQINTCODE { 129 address 0x002 130 access_mode RW 131 field { 132 NO_SEQINT, /* No seqint pending. */ 133 BAD_PHASE, /* unknown scsi bus phase */ 134 SEND_REJECT, /* sending a message reject */ 135 PROTO_VIOLATION, /* Protocol Violation */ 136 NO_MATCH, /* no cmd match for reconnect */ 137 IGN_WIDE_RES, /* Complex IGN Wide Res Msg */ 138 PDATA_REINIT, /* 139 * Returned to data phase 140 * that requires data 141 * transfer pointers to be 142 * recalculated from the 143 * transfer residual. 144 */ 145 HOST_MSG_LOOP, /* 146 * The bus is ready for the 147 * host to perform another 148 * message transaction. This 149 * mechanism is used for things 150 * like sync/wide negotiation 151 * that require a kernel based 152 * message state engine. 153 */ 154 BAD_STATUS, /* Bad status from target */ 155 DATA_OVERRUN, /* 156 * Target attempted to write 157 * beyond the bounds of its 158 * command. 159 */ 160 MKMSG_FAILED, /* 161 * Target completed command 162 * without honoring our ATN 163 * request to issue a message. 164 */ 165 MISSED_BUSFREE, /* 166 * The sequencer never saw 167 * the bus go free after 168 * either a command complete 169 * or disconnect message. 170 */ 171 DUMP_CARD_STATE, 172 ILLEGAL_PHASE, 173 INVALID_SEQINT, 174 CFG4ISTAT_INTR, 175 STATUS_OVERRUN, 176 CFG4OVERRUN, 177 ENTERING_NONPACK, 178 TASKMGMT_FUNC_COMPLETE, /* 179 * Task management function 180 * request completed with 181 * an expected busfree. 182 */ 183 TASKMGMT_CMD_CMPLT_OKAY, /* 184 * A command with a non-zero 185 * task management function 186 * has completed via the normal 187 * command completion method 188 * for commands with a zero 189 * task management function. 190 * This happens when an attempt 191 * to abort a command loses 192 * the race for the command to 193 * complete normally. 194 */ 195 TRACEPOINT0, 196 TRACEPOINT1, 197 TRACEPOINT2, 198 TRACEPOINT3, 199 SAW_HWERR, 200 BAD_SCB_STATUS 201 } 202} 203 204/* 205 * Clear Host Interrupt 206 */ 207register CLRINT { 208 address 0x003 209 access_mode WO 210 field CLRHWERRINT 0x80 /* Rev B or greater */ 211 field CLRBRKADRINT 0x40 212 field CLRSWTMINT 0x20 213 field CLRPCIINT 0x10 214 field CLRSCSIINT 0x08 215 field CLRSEQINT 0x04 216 field CLRCMDINT 0x02 217 field CLRSPLTINT 0x01 218} 219 220/* 221 * Error Register 222 */ 223register ERROR { 224 address 0x004 225 access_mode RO 226 field CIOPARERR 0x80 227 field CIOACCESFAIL 0x40 /* Rev B or greater */ 228 field MPARERR 0x20 229 field DPARERR 0x10 230 field SQPARERR 0x08 231 field ILLOPCODE 0x04 232 field DSCTMOUT 0x02 233} 234 235/* 236 * Clear Error 237 */ 238register CLRERR { 239 address 0x004 240 access_mode WO 241 field CLRCIOPARERR 0x80 242 field CLRCIOACCESFAIL 0x40 /* Rev B or greater */ 243 field CLRMPARERR 0x20 244 field CLRDPARERR 0x10 245 field CLRSQPARERR 0x08 246 field CLRILLOPCODE 0x04 247 field CLRDSCTMOUT 0x02 248} 249 250/* 251 * Host Control Register 252 * Overall host control of the device. 253 */ 254register HCNTRL { 255 address 0x005 256 access_mode RW 257 field SEQ_RESET 0x80 /* Rev B or greater */ 258 field POWRDN 0x40 259 field SWINT 0x10 260 field SWTIMER_START_B 0x08 /* Rev B or greater */ 261 field PAUSE 0x04 262 field INTEN 0x02 263 field CHIPRST 0x01 264 field CHIPRSTACK 0x01 265} 266 267/* 268 * Host New SCB Queue Offset 269 */ 270register HNSCB_QOFF { 271 address 0x006 272 access_mode RW 273 size 2 274} 275 276/* 277 * Host Empty SCB Queue Offset 278 */ 279register HESCB_QOFF { 280 address 0x008 281 access_mode RW 282} 283 284/* 285 * Host Mailbox 286 */ 287register HS_MAILBOX { 288 address 0x00B 289 access_mode RW 290 mask HOST_TQINPOS 0x80 /* Boundary at either 0 or 128 */ 291 mask ENINT_COALESCE 0x40 /* Perform interrupt coalescing */ 292} 293 294/* 295 * Sequencer Interrupt Status 296 */ 297register SEQINTSTAT { 298 address 0x00C 299 access_mode RO 300 field SEQ_SWTMRTO 0x10 301 field SEQ_SEQINT 0x08 302 field SEQ_SCSIINT 0x04 303 field SEQ_PCIINT 0x02 304 field SEQ_SPLTINT 0x01 305} 306 307/* 308 * Clear SEQ Interrupt 309 */ 310register CLRSEQINTSTAT { 311 address 0x00C 312 access_mode WO 313 field CLRSEQ_SWTMRTO 0x10 314 field CLRSEQ_SEQINT 0x08 315 field CLRSEQ_SCSIINT 0x04 316 field CLRSEQ_PCIINT 0x02 317 field CLRSEQ_SPLTINT 0x01 318} 319 320/* 321 * Software Timer 322 */ 323register SWTIMER { 324 address 0x00E 325 access_mode RW 326 size 2 327} 328 329/* 330 * SEQ New SCB Queue Offset 331 */ 332register SNSCB_QOFF { 333 address 0x010 334 access_mode RW 335 size 2 336 modes M_CCHAN 337} 338 339/* 340 * SEQ Empty SCB Queue Offset 341 */ 342register SESCB_QOFF { 343 address 0x012 344 access_mode RW 345 modes M_CCHAN 346} 347 348/* 349 * SEQ Done SCB Queue Offset 350 */ 351register SDSCB_QOFF { 352 address 0x014 353 access_mode RW 354 modes M_CCHAN 355 size 2 356} 357 358/* 359 * Queue Offset Control & Status 360 */ 361register QOFF_CTLSTA { 362 address 0x016 363 access_mode RW 364 modes M_CCHAN 365 field EMPTY_SCB_AVAIL 0x80 366 field NEW_SCB_AVAIL 0x40 367 field SDSCB_ROLLOVR 0x20 368 field HS_MAILBOX_ACT 0x10 369 field SCB_QSIZE 0x0F { 370 SCB_QSIZE_4, 371 SCB_QSIZE_8, 372 SCB_QSIZE_16, 373 SCB_QSIZE_32, 374 SCB_QSIZE_64, 375 SCB_QSIZE_128, 376 SCB_QSIZE_256, 377 SCB_QSIZE_512, 378 SCB_QSIZE_1024, 379 SCB_QSIZE_2048, 380 SCB_QSIZE_4096, 381 SCB_QSIZE_8192, 382 SCB_QSIZE_16384 383 } 384} 385 386/* 387 * Interrupt Control 388 */ 389register INTCTL { 390 address 0x018 391 access_mode RW 392 field SWTMINTMASK 0x80 393 field SWTMINTEN 0x40 394 field SWTIMER_START 0x20 395 field AUTOCLRCMDINT 0x10 396 field PCIINTEN 0x08 397 field SCSIINTEN 0x04 398 field SEQINTEN 0x02 399 field SPLTINTEN 0x01 400} 401 402/* 403 * Data FIFO Control 404 */ 405register DFCNTRL { 406 address 0x019 407 access_mode RW 408 modes M_DFF0, M_DFF1 409 field PRELOADEN 0x80 410 field SCSIENWRDIS 0x40 /* Rev B only. */ 411 field SCSIEN 0x20 412 field SCSIENACK 0x20 413 field HDMAEN 0x08 414 field HDMAENACK 0x08 415 field DIRECTION 0x04 416 field DIRECTIONACK 0x04 417 field FIFOFLUSH 0x02 418 field FIFOFLUSHACK 0x02 419 field DIRECTIONEN 0x01 420} 421 422/* 423 * Device Space Command 0 424 */ 425register DSCOMMAND0 { 426 address 0x019 427 access_mode RW 428 modes M_CFG 429 field CACHETHEN 0x80 /* Cache Threshold enable */ 430 field DPARCKEN 0x40 /* Data Parity Check Enable */ 431 field MPARCKEN 0x20 /* Memory Parity Check Enable */ 432 field EXTREQLCK 0x10 /* External Request Lock */ 433 field DISABLE_TWATE 0x02 /* Rev B or greater */ 434 field CIOPARCKEN 0x01 /* Internal bus parity error enable */ 435} 436 437/* 438 * Data FIFO Status 439 */ 440register DFSTATUS { 441 address 0x01A 442 access_mode RO 443 modes M_DFF0, M_DFF1 444 field PRELOAD_AVAIL 0x80 445 field PKT_PRELOAD_AVAIL 0x40 446 field MREQPEND 0x10 447 field HDONE 0x08 448 field DFTHRESH 0x04 449 field FIFOFULL 0x02 450 field FIFOEMP 0x01 451} 452 453/* 454 * S/G Cache Pointer 455 */ 456register SG_CACHE_PRE { 457 address 0x01B 458 access_mode WO 459 modes M_DFF0, M_DFF1 460 field SG_ADDR_MASK 0xf8 461 field ODD_SEG 0x04 462 field LAST_SEG 0x02 463} 464 465register SG_CACHE_SHADOW { 466 address 0x01B 467 access_mode RO 468 modes M_DFF0, M_DFF1 469 field SG_ADDR_MASK 0xf8 470 field ODD_SEG 0x04 471 field LAST_SEG 0x02 472 field LAST_SEG_DONE 0x01 473} 474 475/* 476 * Arbiter Control 477 */ 478register ARBCTL { 479 address 0x01B 480 access_mode RW 481 modes M_CFG 482 field RESET_HARB 0x80 483 field RETRY_SWEN 0x08 484 field USE_TIME 0x07 485} 486 487/* 488 * Data Channel Host Address 489 */ 490register HADDR { 491 address 0x070 492 access_mode RW 493 size 8 494 modes M_DFF0, M_DFF1 495} 496 497/* 498 * Host Overlay DMA Address 499 */ 500register HODMAADR { 501 address 0x070 502 access_mode RW 503 size 8 504 modes M_SCSI 505} 506 507/* 508 * PCI PLL Delay. 509 */ 510register PLLDELAY { 511 address 0x070 512 access_mode RW 513 size 1 514 modes M_CFG 515 field SPLIT_DROP_REQ 0x80 516} 517 518/* 519 * Data Channel Host Count 520 */ 521register HCNT { 522 address 0x078 523 access_mode RW 524 size 3 525 modes M_DFF0, M_DFF1 526} 527 528/* 529 * Host Overlay DMA Count 530 */ 531register HODMACNT { 532 address 0x078 533 access_mode RW 534 size 2 535 modes M_SCSI 536} 537 538/* 539 * Host Overlay DMA Enable 540 */ 541register HODMAEN { 542 address 0x07A 543 access_mode RW 544 modes M_SCSI 545} 546 547/* 548 * Scatter/Gather Host Address 549 */ 550register SGHADDR { 551 address 0x07C 552 access_mode RW 553 size 8 554 modes M_DFF0, M_DFF1 555} 556 557/* 558 * SCB Host Address 559 */ 560register SCBHADDR { 561 address 0x07C 562 access_mode RW 563 size 8 564 modes M_CCHAN 565} 566 567/* 568 * Scatter/Gather Host Count 569 */ 570register SGHCNT { 571 address 0x084 572 access_mode RW 573 modes M_DFF0, M_DFF1 574} 575 576/* 577 * SCB Host Count 578 */ 579register SCBHCNT { 580 address 0x084 581 access_mode RW 582 modes M_CCHAN 583} 584 585/* 586 * Data FIFO Threshold 587 */ 588register DFF_THRSH { 589 address 0x088 590 access_mode RW 591 modes M_CFG 592 field WR_DFTHRSH 0x70 { 593 WR_DFTHRSH_MIN, 594 WR_DFTHRSH_25, 595 WR_DFTHRSH_50, 596 WR_DFTHRSH_63, 597 WR_DFTHRSH_75, 598 WR_DFTHRSH_85, 599 WR_DFTHRSH_90, 600 WR_DFTHRSH_MAX 601 } 602 field RD_DFTHRSH 0x07 { 603 RD_DFTHRSH_MIN, 604 RD_DFTHRSH_25, 605 RD_DFTHRSH_50, 606 RD_DFTHRSH_63, 607 RD_DFTHRSH_75, 608 RD_DFTHRSH_85, 609 RD_DFTHRSH_90, 610 RD_DFTHRSH_MAX 611 } 612} 613 614/* 615 * ROM Address 616 */ 617register ROMADDR { 618 address 0x08A 619 access_mode RW 620 size 3 621} 622 623/* 624 * ROM Control 625 */ 626register ROMCNTRL { 627 address 0x08D 628 access_mode RW 629 field ROMOP 0xE0 630 field ROMSPD 0x18 631 field REPEAT 0x02 632 field RDY 0x01 633} 634 635/* 636 * ROM Data 637 */ 638register ROMDATA { 639 address 0x08E 640 access_mode RW 641} 642 643/* 644 * Data Channel Receive Message 0 645 */ 646register DCHRXMSG0 { 647 address 0x090 648 access_mode RO 649 modes M_DFF0, M_DFF1 650 field CDNUM 0xF8 651 field CFNUM 0x07 652} 653 654/* 655 * CMC Recieve Message 0 656 */ 657register CMCRXMSG0 { 658 address 0x090 659 access_mode RO 660 modes M_CCHAN 661 field CDNUM 0xF8 662 field CFNUM 0x07 663} 664 665/* 666 * Overlay Recieve Message 0 667 */ 668register OVLYRXMSG0 { 669 address 0x090 670 access_mode RO 671 modes M_SCSI 672 field CDNUM 0xF8 673 field CFNUM 0x07 674} 675 676/* 677 * Relaxed Order Enable 678 */ 679register ROENABLE { 680 address 0x090 681 access_mode RW 682 modes M_CFG 683 field MSIROEN 0x20 684 field OVLYROEN 0x10 685 field CMCROEN 0x08 686 field SGROEN 0x04 687 field DCH1ROEN 0x02 688 field DCH0ROEN 0x01 689} 690 691/* 692 * Data Channel Receive Message 1 693 */ 694register DCHRXMSG1 { 695 address 0x091 696 access_mode RO 697 modes M_DFF0, M_DFF1 698 field CBNUM 0xFF 699} 700 701/* 702 * CMC Recieve Message 1 703 */ 704register CMCRXMSG1 { 705 address 0x091 706 access_mode RO 707 modes M_CCHAN 708 field CBNUM 0xFF 709} 710 711/* 712 * Overlay Recieve Message 1 713 */ 714register OVLYRXMSG1 { 715 address 0x091 716 access_mode RO 717 modes M_SCSI 718 field CBNUM 0xFF 719} 720 721/* 722 * No Snoop Enable 723 */ 724register NSENABLE { 725 address 0x091 726 access_mode RW 727 modes M_CFG 728 field MSINSEN 0x20 729 field OVLYNSEN 0x10 730 field CMCNSEN 0x08 731 field SGNSEN 0x04 732 field DCH1NSEN 0x02 733 field DCH0NSEN 0x01 734} 735 736/* 737 * Data Channel Receive Message 2 738 */ 739register DCHRXMSG2 { 740 address 0x092 741 access_mode RO 742 modes M_DFF0, M_DFF1 743 field MINDEX 0xFF 744} 745 746/* 747 * CMC Recieve Message 2 748 */ 749register CMCRXMSG2 { 750 address 0x092 751 access_mode RO 752 modes M_CCHAN 753 field MINDEX 0xFF 754} 755 756/* 757 * Overlay Recieve Message 2 758 */ 759register OVLYRXMSG2 { 760 address 0x092 761 access_mode RO 762 modes M_SCSI 763 field MINDEX 0xFF 764} 765 766/* 767 * Outstanding Split Transactions 768 */ 769register OST { 770 address 0x092 771 access_mode RW 772 modes M_CFG 773} 774 775/* 776 * Data Channel Receive Message 3 777 */ 778register DCHRXMSG3 { 779 address 0x093 780 access_mode RO 781 modes M_DFF0, M_DFF1 782 field MCLASS 0x0F 783} 784 785/* 786 * CMC Recieve Message 3 787 */ 788register CMCRXMSG3 { 789 address 0x093 790 access_mode RO 791 modes M_CCHAN 792 field MCLASS 0x0F 793} 794 795/* 796 * Overlay Recieve Message 3 797 */ 798register OVLYRXMSG3 { 799 address 0x093 800 access_mode RO 801 modes M_SCSI 802 field MCLASS 0x0F 803} 804 805/* 806 * PCI-X Control 807 */ 808register PCIXCTL { 809 address 0x093 810 access_mode RW 811 modes M_CFG 812 field SERRPULSE 0x80 813 field UNEXPSCIEN 0x20 814 field SPLTSMADIS 0x10 815 field SPLTSTADIS 0x08 816 field SRSPDPEEN 0x04 817 field TSCSERREN 0x02 818 field CMPABCDIS 0x01 819} 820 821/* 822 * CMC Sequencer Byte Count 823 */ 824register CMCSEQBCNT { 825 address 0x094 826 access_mode RO 827 modes M_CCHAN 828} 829 830/* 831 * Overlay Sequencer Byte Count 832 */ 833register OVLYSEQBCNT { 834 address 0x094 835 access_mode RO 836 modes M_SCSI 837} 838 839/* 840 * Data Channel Sequencer Byte Count 841 */ 842register DCHSEQBCNT { 843 address 0x094 844 access_mode RO 845 size 2 846 modes M_DFF0, M_DFF1 847} 848 849/* 850 * Data Channel Split Status 0 851 */ 852register DCHSPLTSTAT0 { 853 address 0x096 854 access_mode RW 855 modes M_DFF0, M_DFF1 856 field STAETERM 0x80 857 field SCBCERR 0x40 858 field SCADERR 0x20 859 field SCDATBUCKET 0x10 860 field CNTNOTCMPLT 0x08 861 field RXOVRUN 0x04 862 field RXSCEMSG 0x02 863 field RXSPLTRSP 0x01 864} 865 866/* 867 * CMC Split Status 0 868 */ 869register CMCSPLTSTAT0 { 870 address 0x096 871 access_mode RW 872 modes M_CCHAN 873 field STAETERM 0x80 874 field SCBCERR 0x40 875 field SCADERR 0x20 876 field SCDATBUCKET 0x10 877 field CNTNOTCMPLT 0x08 878 field RXOVRUN 0x04 879 field RXSCEMSG 0x02 880 field RXSPLTRSP 0x01 881} 882 883/* 884 * Overlay Split Status 0 885 */ 886register OVLYSPLTSTAT0 { 887 address 0x096 888 access_mode RW 889 modes M_SCSI 890 field STAETERM 0x80 891 field SCBCERR 0x40 892 field SCADERR 0x20 893 field SCDATBUCKET 0x10 894 field CNTNOTCMPLT 0x08 895 field RXOVRUN 0x04 896 field RXSCEMSG 0x02 897 field RXSPLTRSP 0x01 898} 899 900/* 901 * Data Channel Split Status 1 902 */ 903register DCHSPLTSTAT1 { 904 address 0x097 905 access_mode RW 906 modes M_DFF0, M_DFF1 907 field RXDATABUCKET 0x01 908} 909 910/* 911 * CMC Split Status 1 912 */ 913register CMCSPLTSTAT1 { 914 address 0x097 915 access_mode RW 916 modes M_CCHAN 917 field RXDATABUCKET 0x01 918} 919 920/* 921 * Overlay Split Status 1 922 */ 923register OVLYSPLTSTAT1 { 924 address 0x097 925 access_mode RW 926 modes M_SCSI 927 field RXDATABUCKET 0x01 928} 929 930/* 931 * S/G Receive Message 0 932 */ 933register SGRXMSG0 { 934 address 0x098 935 access_mode RO 936 modes M_DFF0, M_DFF1 937 field CDNUM 0xF8 938 field CFNUM 0x07 939} 940 941/* 942 * S/G Receive Message 1 943 */ 944register SGRXMSG1 { 945 address 0x099 946 access_mode RO 947 modes M_DFF0, M_DFF1 948 field CBNUM 0xFF 949} 950 951/* 952 * S/G Receive Message 2 953 */ 954register SGRXMSG2 { 955 address 0x09A 956 access_mode RO 957 modes M_DFF0, M_DFF1 958 field MINDEX 0xFF 959} 960 961/* 962 * S/G Receive Message 3 963 */ 964register SGRXMSG3 { 965 address 0x09B 966 access_mode RO 967 modes M_DFF0, M_DFF1 968 field MCLASS 0x0F 969} 970 971/* 972 * Slave Split Out Address 0 973 */ 974register SLVSPLTOUTADR0 { 975 address 0x098 976 access_mode RO 977 modes M_SCSI 978 field LOWER_ADDR 0x7F 979} 980 981/* 982 * Slave Split Out Address 1 983 */ 984register SLVSPLTOUTADR1 { 985 address 0x099 986 access_mode RO 987 modes M_SCSI 988 field REQ_DNUM 0xF8 989 field REQ_FNUM 0x07 990} 991 992/* 993 * Slave Split Out Address 2 994 */ 995register SLVSPLTOUTADR2 { 996 address 0x09A 997 access_mode RO 998 modes M_SCSI 999 field REQ_BNUM 0xFF 1000} 1001 1002/* 1003 * Slave Split Out Address 3 1004 */ 1005register SLVSPLTOUTADR3 { 1006 address 0x09B 1007 access_mode RO 1008 modes M_SCSI 1009 field RLXORD 020 1010 field TAG_NUM 0x1F 1011} 1012 1013/* 1014 * SG Sequencer Byte Count 1015 */ 1016register SGSEQBCNT { 1017 address 0x09C 1018 access_mode RO 1019 modes M_DFF0, M_DFF1 1020} 1021 1022/* 1023 * Slave Split Out Attribute 0 1024 */ 1025register SLVSPLTOUTATTR0 { 1026 address 0x09C 1027 access_mode RO 1028 modes M_SCSI 1029 field LOWER_BCNT 0xFF 1030} 1031 1032/* 1033 * Slave Split Out Attribute 1 1034 */ 1035register SLVSPLTOUTATTR1 { 1036 address 0x09D 1037 access_mode RO 1038 modes M_SCSI 1039 field CMPLT_DNUM 0xF8 1040 field CMPLT_FNUM 0x07 1041} 1042 1043/* 1044 * Slave Split Out Attribute 2 1045 */ 1046register SLVSPLTOUTATTR2 { 1047 address 0x09E 1048 access_mode RO 1049 size 2 1050 modes M_SCSI 1051 field CMPLT_BNUM 0xFF 1052} 1053/* 1054 * S/G Split Status 0 1055 */ 1056register SGSPLTSTAT0 { 1057 address 0x09E 1058 access_mode RW 1059 modes M_DFF0, M_DFF1 1060 field STAETERM 0x80 1061 field SCBCERR 0x40 1062 field SCADERR 0x20 1063 field SCDATBUCKET 0x10 1064 field CNTNOTCMPLT 0x08 1065 field RXOVRUN 0x04 1066 field RXSCEMSG 0x02 1067 field RXSPLTRSP 0x01 1068} 1069 1070/* 1071 * S/G Split Status 1 1072 */ 1073register SGSPLTSTAT1 { 1074 address 0x09F 1075 access_mode RW 1076 modes M_DFF0, M_DFF1 1077 field RXDATABUCKET 0x01 1078} 1079 1080/* 1081 * Special Function 1082 */ 1083register SFUNCT { 1084 address 0x09f 1085 access_mode RW 1086 modes M_CFG 1087 field TEST_GROUP 0xF0 1088 field TEST_NUM 0x0F 1089} 1090 1091/* 1092 * Data FIFO 0 PCI Status 1093 */ 1094register DF0PCISTAT { 1095 address 0x0A0 1096 access_mode RW 1097 modes M_CFG 1098 field DPE 0x80 1099 field SSE 0x40 1100 field RMA 0x20 1101 field RTA 0x10 1102 field SCAAPERR 0x08 1103 field RDPERR 0x04 1104 field TWATERR 0x02 1105 field DPR 0x01 1106} 1107 1108/* 1109 * Data FIFO 1 PCI Status 1110 */ 1111register DF1PCISTAT { 1112 address 0x0A1 1113 access_mode RW 1114 modes M_CFG 1115 field DPE 0x80 1116 field SSE 0x40 1117 field RMA 0x20 1118 field RTA 0x10 1119 field SCAAPERR 0x08 1120 field RDPERR 0x04 1121 field TWATERR 0x02 1122 field DPR 0x01 1123} 1124 1125/* 1126 * S/G PCI Status 1127 */ 1128register SGPCISTAT { 1129 address 0x0A2 1130 access_mode RW 1131 modes M_CFG 1132 field DPE 0x80 1133 field SSE 0x40 1134 field RMA 0x20 1135 field RTA 0x10 1136 field SCAAPERR 0x08 1137 field RDPERR 0x04 1138 field DPR 0x01 1139} 1140 1141/* 1142 * CMC PCI Status 1143 */ 1144register CMCPCISTAT { 1145 address 0x0A3 1146 access_mode RW 1147 modes M_CFG 1148 field DPE 0x80 1149 field SSE 0x40 1150 field RMA 0x20 1151 field RTA 0x10 1152 field SCAAPERR 0x08 1153 field RDPERR 0x04 1154 field TWATERR 0x02 1155 field DPR 0x01 1156} 1157 1158/* 1159 * Overlay PCI Status 1160 */ 1161register OVLYPCISTAT { 1162 address 0x0A4 1163 access_mode RW 1164 modes M_CFG 1165 field DPE 0x80 1166 field SSE 0x40 1167 field RMA 0x20 1168 field RTA 0x10 1169 field SCAAPERR 0x08 1170 field RDPERR 0x04 1171 field DPR 0x01 1172} 1173 1174/* 1175 * PCI Status for MSI Master DMA Transfer 1176 */ 1177register MSIPCISTAT { 1178 address 0x0A6 1179 access_mode RW 1180 modes M_CFG 1181 field SSE 0x40 1182 field RMA 0x20 1183 field RTA 0x10 1184 field CLRPENDMSI 0x08 1185 field TWATERR 0x02 1186 field DPR 0x01 1187} 1188 1189/* 1190 * PCI Status for Target 1191 */ 1192register TARGPCISTAT { 1193 address 0x0A7 1194 access_mode RW 1195 modes M_CFG 1196 field DPE 0x80 1197 field SSE 0x40 1198 field STA 0x08 1199 field TWATERR 0x02 1200} 1201 1202/* 1203 * LQ Packet In 1204 * The last LQ Packet recieved 1205 */ 1206register LQIN { 1207 address 0x020 1208 access_mode RW 1209 size 20 1210 modes M_DFF0, M_DFF1, M_SCSI 1211} 1212 1213/* 1214 * SCB Type Pointer 1215 * SCB offset for Target Mode SCB type information 1216 */ 1217register TYPEPTR { 1218 address 0x020 1219 access_mode RW 1220 modes M_CFG 1221} 1222 1223/* 1224 * Queue Tag Pointer 1225 * SCB offset to the Two Byte tag identifier used for target mode. 1226 */ 1227register TAGPTR { 1228 address 0x021 1229 access_mode RW 1230 modes M_CFG 1231} 1232 1233/* 1234 * Logical Unit Number Pointer 1235 * SCB offset to the LSB (little endian) of the lun field. 1236 */ 1237register LUNPTR { 1238 address 0x022 1239 access_mode RW 1240 modes M_CFG 1241} 1242 1243/* 1244 * Data Length Pointer 1245 * SCB offset for the 4 byte data length field in target mode. 1246 */ 1247register DATALENPTR { 1248 address 0x023 1249 access_mode RW 1250 modes M_CFG 1251} 1252 1253/* 1254 * Status Length Pointer 1255 * SCB offset to the two byte status field in target SCBs. 1256 */ 1257register STATLENPTR { 1258 address 0x024 1259 access_mode RW 1260 modes M_CFG 1261} 1262 1263/* 1264 * Command Length Pointer 1265 * Scb offset for the CDB length field in initiator SCBs. 1266 */ 1267register CMDLENPTR { 1268 address 0x025 1269 access_mode RW 1270 modes M_CFG 1271} 1272 1273/* 1274 * Task Attribute Pointer 1275 * Scb offset for the byte field specifying the attribute byte 1276 * to be used in command packets. 1277 */ 1278register ATTRPTR { 1279 address 0x026 1280 access_mode RW 1281 modes M_CFG 1282} 1283 1284/* 1285 * Task Management Flags Pointer 1286 * Scb offset for the byte field specifying the attribute flags 1287 * byte to be used in command packets. 1288 */ 1289register FLAGPTR { 1290 address 0x027 1291 access_mode RW 1292 modes M_CFG 1293} 1294 1295/* 1296 * Command Pointer 1297 * Scb offset for the first byte in the CDB for initiator SCBs. 1298 */ 1299register CMDPTR { 1300 address 0x028 1301 access_mode RW 1302 modes M_CFG 1303} 1304 1305/* 1306 * Queue Next Pointer 1307 * Scb offset for the 2 byte "next scb link". 1308 */ 1309register QNEXTPTR { 1310 address 0x029 1311 access_mode RW 1312 modes M_CFG 1313} 1314 1315/* 1316 * SCSI ID Pointer 1317 * Scb offset to the value to place in the SCSIID register 1318 * during target mode connections. 1319 */ 1320register IDPTR { 1321 address 0x02A 1322 access_mode RW 1323 modes M_CFG 1324} 1325 1326/* 1327 * Command Aborted Byte Pointer 1328 * Offset to the SCB flags field that includes the 1329 * "SCB aborted" status bit. 1330 */ 1331register ABRTBYTEPTR { 1332 address 0x02B 1333 access_mode RW 1334 modes M_CFG 1335} 1336 1337/* 1338 * Command Aborted Bit Pointer 1339 * Bit offset in the SCB flags field for "SCB aborted" status. 1340 */ 1341register ABRTBITPTR { 1342 address 0x02C 1343 access_mode RW 1344 modes M_CFG 1345} 1346 1347/* 1348 * Rev B or greater. 1349 */ 1350register MAXCMDBYTES { 1351 address 0x02D 1352 access_mode RW 1353 modes M_CFG 1354} 1355 1356/* 1357 * Rev B or greater. 1358 */ 1359register MAXCMD2RCV { 1360 address 0x02E 1361 access_mode RW 1362 modes M_CFG 1363} 1364 1365/* 1366 * Rev B or greater. 1367 */ 1368register SHORTTHRESH { 1369 address 0x02F 1370 access_mode RW 1371 modes M_CFG 1372} 1373 1374/* 1375 * Logical Unit Number Length 1376 * The length, in bytes, of the SCB lun field. 1377 */ 1378register LUNLEN { 1379 address 0x030 1380 access_mode RW 1381 modes M_CFG 1382 mask ILUNLEN 0x0F 1383 mask TLUNLEN 0xF0 1384} 1385const LUNLEN_SINGLE_LEVEL_LUN 0xF 1386 1387/* 1388 * CDB Limit 1389 * The size, in bytes, of the embedded CDB field in initator SCBs. 1390 */ 1391register CDBLIMIT { 1392 address 0x031 1393 access_mode RW 1394 modes M_CFG 1395} 1396 1397/* 1398 * Maximum Commands 1399 * The maximum number of commands to issue during a 1400 * single packetized connection. 1401 */ 1402register MAXCMD { 1403 address 0x032 1404 access_mode RW 1405 modes M_CFG 1406} 1407 1408/* 1409 * Maximum Command Counter 1410 * The number of commands already sent during this connection 1411 */ 1412register MAXCMDCNT { 1413 address 0x033 1414 access_mode RW 1415 modes M_CFG 1416} 1417 1418/* 1419 * LQ Packet Reserved Bytes 1420 * The bytes to be sent in the currently reserved fileds 1421 * of all LQ packets. 1422 */ 1423register LQRSVD01 { 1424 address 0x034 1425 access_mode RW 1426 modes M_SCSI 1427} 1428register LQRSVD16 { 1429 address 0x035 1430 access_mode RW 1431 modes M_SCSI 1432} 1433register LQRSVD17 { 1434 address 0x036 1435 access_mode RW 1436 modes M_SCSI 1437} 1438 1439/* 1440 * Command Reserved 0 1441 * The byte to be sent for the reserved byte 0 of 1442 * outgoing command packets. 1443 */ 1444register CMDRSVD0 { 1445 address 0x037 1446 access_mode RW 1447 modes M_CFG 1448} 1449 1450/* 1451 * LQ Manager Control 0 1452 */ 1453register LQCTL0 { 1454 address 0x038 1455 access_mode RW 1456 modes M_CFG 1457 field LQITARGCLT 0xC0 1458 field LQIINITGCLT 0x30 1459 field LQ0TARGCLT 0x0C 1460 field LQ0INITGCLT 0x03 1461} 1462 1463/* 1464 * LQ Manager Control 1 1465 */ 1466register LQCTL1 { 1467 address 0x038 1468 access_mode RW 1469 modes M_DFF0, M_DFF1, M_SCSI 1470 field PCI2PCI 0x04 1471 field SINGLECMD 0x02 1472 field ABORTPENDING 0x01 1473} 1474 1475/* 1476 * LQ Manager Control 2 1477 */ 1478register LQCTL2 { 1479 address 0x039 1480 access_mode RW 1481 modes M_DFF0, M_DFF1, M_SCSI 1482 field LQIRETRY 0x80 1483 field LQICONTINUE 0x40 1484 field LQITOIDLE 0x20 1485 field LQIPAUSE 0x10 1486 field LQORETRY 0x08 1487 field LQOCONTINUE 0x04 1488 field LQOTOIDLE 0x02 1489 field LQOPAUSE 0x01 1490} 1491 1492/* 1493 * SCSI RAM BIST0 1494 */ 1495register SCSBIST0 { 1496 address 0x039 1497 access_mode RW 1498 modes M_CFG 1499 field GSBISTERR 0x40 1500 field GSBISTDONE 0x20 1501 field GSBISTRUN 0x10 1502 field OSBISTERR 0x04 1503 field OSBISTDONE 0x02 1504 field OSBISTRUN 0x01 1505} 1506 1507/* 1508 * SCSI Sequence Control0 1509 */ 1510register SCSISEQ0 { 1511 address 0x03A 1512 access_mode RW 1513 modes M_DFF0, M_DFF1, M_SCSI 1514 field TEMODEO 0x80 1515 field ENSELO 0x40 1516 field ENARBO 0x20 1517 field FORCEBUSFREE 0x10 1518 field SCSIRSTO 0x01 1519} 1520 1521/* 1522 * SCSI RAM BIST 1 1523 */ 1524register SCSBIST1 { 1525 address 0x03A 1526 access_mode RW 1527 modes M_CFG 1528 field NTBISTERR 0x04 1529 field NTBISTDONE 0x02 1530 field NTBISTRUN 0x01 1531} 1532 1533/* 1534 * SCSI Sequence Control 1 1535 */ 1536register SCSISEQ1 { 1537 address 0x03B 1538 access_mode RW 1539 modes M_DFF0, M_DFF1, M_SCSI 1540 field MANUALCTL 0x40 1541 field ENSELI 0x20 1542 field ENRSELI 0x10 1543 field MANUALP 0x0C 1544 field ENAUTOATNP 0x02 1545 field ALTSTIM 0x01 1546} 1547 1548/* 1549 * SCSI Transfer Control 0 1550 */ 1551register SXFRCTL0 { 1552 address 0x03C 1553 access_mode RW 1554 modes M_SCSI 1555 field DFON 0x80 1556 field DFPEXP 0x40 1557 field BIOSCANCELEN 0x10 1558 field SPIOEN 0x08 1559} 1560 1561/* 1562 * SCSI Transfer Control 1 1563 */ 1564register SXFRCTL1 { 1565 address 0x03D 1566 access_mode RW 1567 modes M_SCSI 1568 field BITBUCKET 0x80 1569 field ENSACHK 0x40 1570 field ENSPCHK 0x20 1571 field STIMESEL 0x18 1572 field ENSTIMER 0x04 1573 field ACTNEGEN 0x02 1574 field STPWEN 0x01 1575} 1576 1577/* 1578 * SCSI Transfer Control 2 1579 */ 1580register SXFRCTL2 { 1581 address 0x03E 1582 access_mode RW 1583 modes M_SCSI 1584 field AUTORSTDIS 0x10 1585 field CMDDMAEN 0x08 1586 field ASU 0x07 1587} 1588 1589/* 1590 * SCSI Bus Initiator IDs 1591 * Bitmask of observed initiators on the bus. 1592 */ 1593register BUSINITID { 1594 address 0x03C 1595 access_mode RW 1596 modes M_CFG 1597 size 2 1598} 1599 1600/* 1601 * Data Length Counters 1602 * Packet byte counter. 1603 */ 1604register DLCOUNT { 1605 address 0x03C 1606 access_mode RW 1607 modes M_DFF0, M_DFF1 1608 size 3 1609} 1610 1611/* 1612 * Data FIFO Status 1613 */ 1614register DFFSTAT { 1615 address 0x03F 1616 access_mode RW 1617 modes M_SCSI 1618 field FIFO1FREE 0x20 1619 field FIFO0FREE 0x10 1620 /* 1621 * On the B, this enum only works 1622 * in the read direction. For writes, 1623 * you must use the B version of the 1624 * CURRFIFO_0 definition which is defined 1625 * as a constant outside of this register 1626 * definition to avoid confusing the 1627 * register pretty printing code. 1628 */ 1629 enum CURRFIFO 0x03 { 1630 CURRFIFO_0, 1631 CURRFIFO_1, 1632 CURRFIFO_NONE 0x3 1633 } 1634} 1635 1636const B_CURRFIFO_0 0x2 1637 1638/* 1639 * SCSI Bus Target IDs 1640 * Bitmask of observed targets on the bus. 1641 */ 1642register BUSTARGID { 1643 address 0x03E 1644 access_mode RW 1645 modes M_CFG 1646 size 2 1647} 1648 1649/* 1650 * SCSI Control Signal Out 1651 */ 1652register SCSISIGO { 1653 address 0x040 1654 access_mode RW 1655 modes M_DFF0, M_DFF1, M_SCSI 1656 field CDO 0x80 1657 field IOO 0x40 1658 field MSGO 0x20 1659 field ATNO 0x10 1660 field SELO 0x08 1661 field BSYO 0x04 1662 field REQO 0x02 1663 field ACKO 0x01 1664/* 1665 * Possible phases to write into SCSISIG0 1666 */ 1667 enum PHASE_MASK CDO|IOO|MSGO { 1668 P_DATAOUT 0x0, 1669 P_DATAIN IOO, 1670 P_DATAOUT_DT P_DATAOUT|MSGO, 1671 P_DATAIN_DT P_DATAIN|MSGO, 1672 P_COMMAND CDO, 1673 P_MESGOUT CDO|MSGO, 1674 P_STATUS CDO|IOO, 1675 P_MESGIN CDO|IOO|MSGO 1676 } 1677} 1678 1679register SCSISIGI { 1680 address 0x041 1681 access_mode RO 1682 modes M_DFF0, M_DFF1, M_SCSI 1683 field CDI 0x80 1684 field IOI 0x40 1685 field MSGI 0x20 1686 field ATNI 0x10 1687 field SELI 0x08 1688 field BSYI 0x04 1689 field REQI 0x02 1690 field ACKI 0x01 1691/* 1692 * Possible phases in SCSISIGI 1693 */ 1694 enum PHASE_MASK CDO|IOO|MSGO { 1695 P_DATAOUT 0x0, 1696 P_DATAIN IOO, 1697 P_DATAOUT_DT P_DATAOUT|MSGO, 1698 P_DATAIN_DT P_DATAIN|MSGO, 1699 P_COMMAND CDO, 1700 P_MESGOUT CDO|MSGO, 1701 P_STATUS CDO|IOO, 1702 P_MESGIN CDO|IOO|MSGO 1703 } 1704} 1705 1706/* 1707 * Multiple Target IDs 1708 * Bitmask of ids to respond as a target. 1709 */ 1710register MULTARGID { 1711 address 0x040 1712 access_mode RW 1713 modes M_CFG 1714 size 2 1715} 1716 1717/* 1718 * SCSI Phase 1719 */ 1720register SCSIPHASE { 1721 address 0x042 1722 access_mode RO 1723 modes M_DFF0, M_DFF1, M_SCSI 1724 field STATUS_PHASE 0x20 1725 field COMMAND_PHASE 0x10 1726 field MSG_IN_PHASE 0x08 1727 field MSG_OUT_PHASE 0x04 1728 field DATA_PHASE_MASK 0x03 { 1729 DATA_OUT_PHASE 0x01, 1730 DATA_IN_PHASE 0x02 1731 } 1732} 1733 1734/* 1735 * SCSI Data 0 Image 1736 */ 1737register SCSIDAT0_IMG { 1738 address 0x043 1739 access_mode RW 1740 modes M_DFF0, M_DFF1, M_SCSI 1741} 1742 1743/* 1744 * SCSI Latched Data 1745 */ 1746register SCSIDAT { 1747 address 0x044 1748 access_mode RW 1749 modes M_DFF0, M_DFF1, M_SCSI 1750 size 2 1751} 1752 1753/* 1754 * SCSI Data Bus 1755 */ 1756register SCSIBUS { 1757 address 0x046 1758 access_mode RW 1759 modes M_DFF0, M_DFF1, M_SCSI 1760 size 2 1761} 1762 1763/* 1764 * Target ID In 1765 */ 1766register TARGIDIN { 1767 address 0x048 1768 access_mode RO 1769 modes M_DFF0, M_DFF1, M_SCSI 1770 field CLKOUT 0x80 1771 field TARGID 0x0F 1772} 1773 1774/* 1775 * Selection/Reselection ID 1776 * Upper four bits are the device id. The ONEBIT is set when the re/selecting 1777 * device did not set its own ID. 1778 */ 1779register SELID { 1780 address 0x049 1781 access_mode RW 1782 modes M_DFF0, M_DFF1, M_SCSI 1783 field SELID_MASK 0xf0 1784 field ONEBIT 0x08 1785} 1786 1787/* 1788 * SCSI Block Control 1789 * Controls Bus type and channel selection. SELWIDE allows for the 1790 * coexistence of 8bit and 16bit devices on a wide bus. 1791 */ 1792register SBLKCTL { 1793 address 0x04A 1794 access_mode RW 1795 modes M_DFF0, M_DFF1, M_SCSI 1796 field DIAGLEDEN 0x80 1797 field DIAGLEDON 0x40 1798 field ENAB40 0x08 /* LVD transceiver active */ 1799 field ENAB20 0x04 /* SE/HVD transceiver active */ 1800 field SELWIDE 0x02 1801} 1802 1803/* 1804 * Option Mode 1805 */ 1806register OPTIONMODE { 1807 address 0x04A 1808 access_mode RW 1809 modes M_CFG 1810 field BIOSCANCTL 0x80 1811 field AUTOACKEN 0x40 1812 field BIASCANCTL 0x20 1813 field BUSFREEREV 0x10 1814 field ENDGFORMCHK 0x04 1815 field AUTO_MSGOUT_DE 0x02 1816 mask OPTIONMODE_DEFAULTS AUTO_MSGOUT_DE 1817} 1818 1819/* 1820 * SCSI Status 0 1821 */ 1822register SSTAT0 { 1823 address 0x04B 1824 access_mode RO 1825 modes M_DFF0, M_DFF1, M_SCSI 1826 field TARGET 0x80 /* Board acting as target */ 1827 field SELDO 0x40 /* Selection Done */ 1828 field SELDI 0x20 /* Board has been selected */ 1829 field SELINGO 0x10 /* Selection In Progress */ 1830 field IOERR 0x08 /* LVD Tranceiver mode changed */ 1831 field OVERRUN 0x04 /* SCSI Offset overrun detected */ 1832 field SPIORDY 0x02 /* SCSI PIO Ready */ 1833 field ARBDO 0x01 /* Arbitration Done Out */ 1834} 1835 1836/* 1837 * Clear SCSI Interrupt 0 1838 * Writing a 1 to a bit clears the associated SCSI Interrupt in SSTAT0. 1839 */ 1840register CLRSINT0 { 1841 address 0x04B 1842 access_mode WO 1843 modes M_DFF0, M_DFF1, M_SCSI 1844 field CLRSELDO 0x40 1845 field CLRSELDI 0x20 1846 field CLRSELINGO 0x10 1847 field CLRIOERR 0x08 1848 field CLROVERRUN 0x04 1849 field CLRSPIORDY 0x02 1850 field CLRARBDO 0x01 1851} 1852 1853/* 1854 * SCSI Interrupt Mode 0 1855 * Setting any bit will enable the corresponding function 1856 * in SIMODE0 to interrupt via the IRQ pin. 1857 */ 1858register SIMODE0 { 1859 address 0x04B 1860 access_mode RW 1861 modes M_CFG 1862 field ENSELDO 0x40 1863 field ENSELDI 0x20 1864 field ENSELINGO 0x10 1865 field ENIOERR 0x08 1866 field ENOVERRUN 0x04 1867 field ENSPIORDY 0x02 1868 field ENARBDO 0x01 1869} 1870 1871/* 1872 * SCSI Status 1 1873 */ 1874register SSTAT1 { 1875 address 0x04C 1876 access_mode RO 1877 modes M_DFF0, M_DFF1, M_SCSI 1878 field SELTO 0x80 1879 field ATNTARG 0x40 1880 field SCSIRSTI 0x20 1881 field PHASEMIS 0x10 1882 field BUSFREE 0x08 1883 field SCSIPERR 0x04 1884 field STRB2FAST 0x02 1885 field REQINIT 0x01 1886} 1887 1888/* 1889 * Clear SCSI Interrupt 1 1890 * Writing a 1 to a bit clears the associated SCSI Interrupt in SSTAT1. 1891 */ 1892register CLRSINT1 { 1893 address 0x04C 1894 access_mode WO 1895 modes M_DFF0, M_DFF1, M_SCSI 1896 field CLRSELTIMEO 0x80 1897 field CLRATNO 0x40 1898 field CLRSCSIRSTI 0x20 1899 field CLRBUSFREE 0x08 1900 field CLRSCSIPERR 0x04 1901 field CLRSTRB2FAST 0x02 1902 field CLRREQINIT 0x01 1903} 1904 1905/* 1906 * SCSI Status 2 1907 */ 1908register SSTAT2 { 1909 address 0x04d 1910 access_mode RO 1911 modes M_DFF0, M_DFF1, M_SCSI 1912 field BUSFREETIME 0xc0 { 1913 BUSFREE_LQO 0x40, 1914 BUSFREE_DFF0 0x80, 1915 BUSFREE_DFF1 0xC0 1916 } 1917 field NONPACKREQ 0x20 1918 field EXP_ACTIVE 0x10 /* SCSI Expander Active */ 1919 field BSYX 0x08 /* Busy Expander */ 1920 field WIDE_RES 0x04 /* Modes 0 and 1 only */ 1921 field SDONE 0x02 /* Modes 0 and 1 only */ 1922 field DMADONE 0x01 /* Modes 0 and 1 only */ 1923} 1924 1925/* 1926 * Clear SCSI Interrupt 2 1927 */ 1928register CLRSINT2 { 1929 address 0x04D 1930 access_mode WO 1931 modes M_DFF0, M_DFF1, M_SCSI 1932 field CLRNONPACKREQ 0x20 1933 field CLRWIDE_RES 0x04 /* Modes 0 and 1 only */ 1934 field CLRSDONE 0x02 /* Modes 0 and 1 only */ 1935 field CLRDMADONE 0x01 /* Modes 0 and 1 only */ 1936} 1937 1938/* 1939 * SCSI Interrupt Mode 2 1940 */ 1941register SIMODE2 { 1942 address 0x04D 1943 access_mode RW 1944 modes M_CFG 1945 field ENWIDE_RES 0x04 1946 field ENSDONE 0x02 1947 field ENDMADONE 0x01 1948} 1949 1950/* 1951 * Physical Error Diagnosis 1952 */ 1953register PERRDIAG { 1954 address 0x04E 1955 access_mode RO 1956 modes M_DFF0, M_DFF1, M_SCSI 1957 field HIZERO 0x80 1958 field HIPERR 0x40 1959 field PREVPHASE 0x20 1960 field PARITYERR 0x10 1961 field AIPERR 0x08 1962 field CRCERR 0x04 1963 field DGFORMERR 0x02 1964 field DTERR 0x01 1965} 1966 1967/* 1968 * LQI Manager Current State 1969 */ 1970register LQISTATE { 1971 address 0x04E 1972 access_mode RO 1973 modes M_CFG 1974} 1975 1976/* 1977 * SCSI Offset Count 1978 */ 1979register SOFFCNT { 1980 address 0x04F 1981 access_mode RO 1982 modes M_DFF0, M_DFF1, M_SCSI 1983} 1984 1985/* 1986 * LQO Manager Current State 1987 */ 1988register LQOSTATE { 1989 address 0x04F 1990 access_mode RO 1991 modes M_CFG 1992} 1993 1994/* 1995 * LQI Manager Status 1996 */ 1997register LQISTAT0 { 1998 address 0x050 1999 access_mode RO 2000 modes M_DFF0, M_DFF1, M_SCSI 2001 field LQIATNQAS 0x20 2002 field LQICRCT1 0x10 2003 field LQICRCT2 0x08 2004 field LQIBADLQT 0x04 2005 field LQIATNLQ 0x02 2006 field LQIATNCMD 0x01 2007} 2008 2009/* 2010 * Clear LQI Interrupts 0 2011 */ 2012register CLRLQIINT0 { 2013 address 0x050 2014 access_mode WO 2015 modes M_DFF0, M_DFF1, M_SCSI 2016 field CLRLQIATNQAS 0x20 2017 field CLRLQICRCT1 0x10 2018 field CLRLQICRCT2 0x08 2019 field CLRLQIBADLQT 0x04 2020 field CLRLQIATNLQ 0x02 2021 field CLRLQIATNCMD 0x01 2022} 2023 2024/* 2025 * LQI Manager Interrupt Mode 0 2026 */ 2027register LQIMODE0 { 2028 address 0x050 2029 access_mode RW 2030 modes M_CFG 2031 field ENLQIATNQASK 0x20 2032 field ENLQICRCT1 0x10 2033 field ENLQICRCT2 0x08 2034 field ENLQIBADLQT 0x04 2035 field ENLQIATNLQ 0x02 2036 field ENLQIATNCMD 0x01 2037} 2038 2039/* 2040 * LQI Manager Status 1 2041 */ 2042register LQISTAT1 { 2043 address 0x051 2044 access_mode RO 2045 modes M_DFF0, M_DFF1, M_SCSI 2046 field LQIPHASE_LQ 0x80 2047 field LQIPHASE_NLQ 0x40 2048 field LQIABORT 0x20 2049 field LQICRCI_LQ 0x10 2050 field LQICRCI_NLQ 0x08 2051 field LQIBADLQI 0x04 2052 field LQIOVERI_LQ 0x02 2053 field LQIOVERI_NLQ 0x01 2054} 2055 2056/* 2057 * Clear LQI Manager Interrupts1 2058 */ 2059register CLRLQIINT1 { 2060 address 0x051 2061 access_mode WO 2062 modes M_DFF0, M_DFF1, M_SCSI 2063 field CLRLQIPHASE_LQ 0x80 2064 field CLRLQIPHASE_NLQ 0x40 2065 field CLRLIQABORT 0x20 2066 field CLRLQICRCI_LQ 0x10 2067 field CLRLQICRCI_NLQ 0x08 2068 field CLRLQIBADLQI 0x04 2069 field CLRLQIOVERI_LQ 0x02 2070 field CLRLQIOVERI_NLQ 0x01 2071} 2072 2073/* 2074 * LQI Manager Interrupt Mode 1 2075 */ 2076register LQIMODE1 { 2077 address 0x051 2078 access_mode RW 2079 modes M_CFG 2080 field ENLQIPHASE_LQ 0x80 /* LQIPHASE1 */ 2081 field ENLQIPHASE_NLQ 0x40 /* LQIPHASE2 */ 2082 field ENLIQABORT 0x20 2083 field ENLQICRCI_LQ 0x10 /* LQICRCI1 */ 2084 field ENLQICRCI_NLQ 0x08 /* LQICRCI2 */ 2085 field ENLQIBADLQI 0x04 2086 field ENLQIOVERI_LQ 0x02 /* LQIOVERI1 */ 2087 field ENLQIOVERI_NLQ 0x01 /* LQIOVERI2 */ 2088} 2089 2090/* 2091 * LQI Manager Status 2 2092 */ 2093register LQISTAT2 { 2094 address 0x052 2095 access_mode RO 2096 modes M_DFF0, M_DFF1, M_SCSI 2097 field PACKETIZED 0x80 2098 field LQIPHASE_OUTPKT 0x40 2099 field LQIWORKONLQ 0x20 2100 field LQIWAITFIFO 0x10 2101 field LQISTOPPKT 0x08 2102 field LQISTOPLQ 0x04 2103 field LQISTOPCMD 0x02 2104 field LQIGSAVAIL 0x01 2105} 2106 2107/* 2108 * SCSI Status 3 2109 */ 2110register SSTAT3 { 2111 address 0x053 2112 access_mode RO 2113 modes M_DFF0, M_DFF1, M_SCSI 2114 field NTRAMPERR 0x02 2115 field OSRAMPERR 0x01 2116} 2117 2118/* 2119 * Clear SCSI Status 3 2120 */ 2121register CLRSINT3 { 2122 address 0x053 2123 access_mode WO 2124 modes M_DFF0, M_DFF1, M_SCSI 2125 field CLRNTRAMPERR 0x02 2126 field CLROSRAMPERR 0x01 2127} 2128 2129/* 2130 * SCSI Interrupt Mode 3 2131 */ 2132register SIMODE3 { 2133 address 0x053 2134 access_mode RW 2135 modes M_CFG 2136 field ENNTRAMPERR 0x02 2137 field ENOSRAMPERR 0x01 2138} 2139 2140/* 2141 * LQO Manager Status 0 2142 */ 2143register LQOSTAT0 { 2144 address 0x054 2145 access_mode RO 2146 modes M_DFF0, M_DFF1, M_SCSI 2147 field LQOTARGSCBPERR 0x10 2148 field LQOSTOPT2 0x08 2149 field LQOATNLQ 0x04 2150 field LQOATNPKT 0x02 2151 field LQOTCRC 0x01 2152} 2153 2154/* 2155 * Clear LQO Manager interrupt 0 2156 */ 2157register CLRLQOINT0 { 2158 address 0x054 2159 access_mode WO 2160 modes M_DFF0, M_DFF1, M_SCSI 2161 field CLRLQOTARGSCBPERR 0x10 2162 field CLRLQOSTOPT2 0x08 2163 field CLRLQOATNLQ 0x04 2164 field CLRLQOATNPKT 0x02 2165 field CLRLQOTCRC 0x01 2166} 2167 2168/* 2169 * LQO Manager Interrupt Mode 0 2170 */ 2171register LQOMODE0 { 2172 address 0x054 2173 access_mode RW 2174 modes M_CFG 2175 field ENLQOTARGSCBPERR 0x10 2176 field ENLQOSTOPT2 0x08 2177 field ENLQOATNLQ 0x04 2178 field ENLQOATNPKT 0x02 2179 field ENLQOTCRC 0x01 2180} 2181 2182/* 2183 * LQO Manager Status 1 2184 */ 2185register LQOSTAT1 { 2186 address 0x055 2187 access_mode RO 2188 modes M_DFF0, M_DFF1, M_SCSI 2189 field LQOINITSCBPERR 0x10 2190 field LQOSTOPI2 0x08 2191 field LQOBADQAS 0x04 2192 field LQOBUSFREE 0x02 2193 field LQOPHACHGINPKT 0x01 2194} 2195 2196/* 2197 * Clear LOQ Interrupt 1 2198 */ 2199register CLRLQOINT1 { 2200 address 0x055 2201 access_mode WO 2202 modes M_DFF0, M_DFF1, M_SCSI 2203 field CLRLQOINITSCBPERR 0x10 2204 field CLRLQOSTOPI2 0x08 2205 field CLRLQOBADQAS 0x04 2206 field CLRLQOBUSFREE 0x02 2207 field CLRLQOPHACHGINPKT 0x01 2208} 2209 2210/* 2211 * LQO Manager Interrupt Mode 1 2212 */ 2213register LQOMODE1 { 2214 address 0x055 2215 access_mode RW 2216 modes M_CFG 2217 field ENLQOINITSCBPERR 0x10 2218 field ENLQOSTOPI2 0x08 2219 field ENLQOBADQAS 0x04 2220 field ENLQOBUSFREE 0x02 2221 field ENLQOPHACHGINPKT 0x01 2222} 2223 2224/* 2225 * LQO Manager Status 2 2226 */ 2227register LQOSTAT2 { 2228 address 0x056 2229 access_mode RO 2230 modes M_DFF0, M_DFF1, M_SCSI 2231 field LQOPKT 0xE0 2232 field LQOWAITFIFO 0x10 2233 field LQOPHACHGOUTPKT 0x02 /* outside of packet boundaries. */ 2234 field LQOSTOP0 0x01 /* Stopped after sending all packets */ 2235} 2236 2237/* 2238 * Output Synchronizer Space Count 2239 */ 2240register OS_SPACE_CNT { 2241 address 0x056 2242 access_mode RO 2243 modes M_CFG 2244} 2245 2246/* 2247 * SCSI Interrupt Mode 1 2248 * Setting any bit will enable the corresponding function 2249 * in SIMODE1 to interrupt via the IRQ pin. 2250 */ 2251register SIMODE1 { 2252 address 0x057 2253 access_mode RW 2254 modes M_DFF0, M_DFF1, M_SCSI 2255 field ENSELTIMO 0x80 2256 field ENATNTARG 0x40 2257 field ENSCSIRST 0x20 2258 field ENPHASEMIS 0x10 2259 field ENBUSFREE 0x08 2260 field ENSCSIPERR 0x04 2261 field ENSTRB2FAST 0x02 2262 field ENREQINIT 0x01 2263} 2264 2265/* 2266 * Good Status FIFO 2267 */ 2268register GSFIFO { 2269 address 0x058 2270 access_mode RO 2271 size 2 2272 modes M_DFF0, M_DFF1, M_SCSI 2273} 2274 2275/* 2276 * Data FIFO SCSI Transfer Control 2277 */ 2278register DFFSXFRCTL { 2279 address 0x05A 2280 access_mode RW 2281 modes M_DFF0, M_DFF1 2282 field DFFBITBUCKET 0x08 2283 field CLRSHCNT 0x04 2284 field CLRCHN 0x02 2285 field RSTCHN 0x01 2286} 2287 2288/* 2289 * Next SCSI Control Block 2290 */ 2291register NEXTSCB { 2292 address 0x05A 2293 access_mode RW 2294 size 2 2295 modes M_SCSI 2296} 2297 2298/* Rev B only. */ 2299register LQOSCSCTL { 2300 address 0x05A 2301 access_mode RW 2302 size 1 2303 modes M_CFG 2304 field LQOH2A_VERSION 0x80 2305 field LQONOCHKOVER 0x01 2306} 2307 2308/* 2309 * SEQ Interrupts 2310 */ 2311register SEQINTSRC { 2312 address 0x05B 2313 access_mode RO 2314 modes M_DFF0, M_DFF1 2315 field CTXTDONE 0x40 2316 field SAVEPTRS 0x20 2317 field CFG4DATA 0x10 2318 field CFG4ISTAT 0x08 2319 field CFG4TSTAT 0x04 2320 field CFG4ICMD 0x02 2321 field CFG4TCMD 0x01 2322} 2323 2324/* 2325 * Clear Arp Interrupts 2326 */ 2327register CLRSEQINTSRC { 2328 address 0x05B 2329 access_mode WO 2330 modes M_DFF0, M_DFF1 2331 field CLRCTXTDONE 0x40 2332 field CLRSAVEPTRS 0x20 2333 field CLRCFG4DATA 0x10 2334 field CLRCFG4ISTAT 0x08 2335 field CLRCFG4TSTAT 0x04 2336 field CLRCFG4ICMD 0x02 2337 field CLRCFG4TCMD 0x01 2338} 2339 2340/* 2341 * SEQ Interrupt Enabled (Shared) 2342 */ 2343register SEQIMODE { 2344 address 0x05C 2345 access_mode RW 2346 modes M_DFF0, M_DFF1 2347 field ENCTXTDONE 0x40 2348 field ENSAVEPTRS 0x20 2349 field ENCFG4DATA 0x10 2350 field ENCFG4ISTAT 0x08 2351 field ENCFG4TSTAT 0x04 2352 field ENCFG4ICMD 0x02 2353 field ENCFG4TCMD 0x01 2354} 2355 2356/* 2357 * Current SCSI Control Block 2358 */ 2359register CURRSCB { 2360 address 0x05C 2361 access_mode RW 2362 size 2 2363 modes M_SCSI 2364} 2365 2366/* 2367 * Data FIFO Status 2368 */ 2369register MDFFSTAT { 2370 address 0x05D 2371 access_mode RO 2372 modes M_DFF0, M_DFF1 2373 field SHCNTNEGATIVE 0x40 /* Rev B or higher */ 2374 field SHCNTMINUS1 0x20 /* Rev B or higher */ 2375 field LASTSDONE 0x10 2376 field SHVALID 0x08 2377 field DLZERO 0x04 /* FIFO data ends on packet boundary. */ 2378 field DATAINFIFO 0x02 2379 field FIFOFREE 0x01 2380} 2381 2382/* 2383 * CRC Control 2384 */ 2385register CRCCONTROL { 2386 address 0x05d 2387 access_mode RW 2388 modes M_CFG 2389 field CRCVALCHKEN 0x40 2390} 2391 2392/* 2393 * SCSI Test Control 2394 */ 2395register SCSITEST { 2396 address 0x05E 2397 access_mode RW 2398 modes M_CFG 2399 field CNTRTEST 0x08 2400 field SEL_TXPLL_DEBUG 0x04 2401} 2402 2403/* 2404 * Data FIFO Queue Tag 2405 */ 2406register DFFTAG { 2407 address 0x05E 2408 access_mode RW 2409 size 2 2410 modes M_DFF0, M_DFF1 2411} 2412 2413/* 2414 * Last SCSI Control Block 2415 */ 2416register LASTSCB { 2417 address 0x05E 2418 access_mode RW 2419 size 2 2420 modes M_SCSI 2421} 2422 2423/* 2424 * SCSI I/O Cell Power-down Control 2425 */ 2426register IOPDNCTL { 2427 address 0x05F 2428 access_mode RW 2429 modes M_CFG 2430 field DISABLE_OE 0x80 2431 field PDN_IDIST 0x04 2432 field PDN_DIFFSENSE 0x01 2433} 2434 2435/* 2436 * Shaddow Host Address. 2437 */ 2438register SHADDR { 2439 address 0x060 2440 access_mode RO 2441 size 8 2442 modes M_DFF0, M_DFF1 2443} 2444 2445/* 2446 * Data Group CRC Interval. 2447 */ 2448register DGRPCRCI { 2449 address 0x060 2450 access_mode RW 2451 size 2 2452 modes M_CFG 2453} 2454 2455/* 2456 * Data Transfer Negotiation Address 2457 */ 2458register NEGOADDR { 2459 address 0x060 2460 access_mode RW 2461 modes M_SCSI 2462} 2463 2464/* 2465 * Data Transfer Negotiation Data - Period Byte 2466 */ 2467register NEGPERIOD { 2468 address 0x061 2469 access_mode RW 2470 modes M_SCSI 2471} 2472 2473/* 2474 * Packetized CRC Interval 2475 */ 2476register PACKCRCI { 2477 address 0x062 2478 access_mode RW 2479 size 2 2480 modes M_CFG 2481} 2482 2483/* 2484 * Data Transfer Negotiation Data - Offset Byte 2485 */ 2486register NEGOFFSET { 2487 address 0x062 2488 access_mode RW 2489 modes M_SCSI 2490} 2491 2492/* 2493 * Data Transfer Negotiation Data - PPR Options 2494 */ 2495register NEGPPROPTS { 2496 address 0x063 2497 access_mode RW 2498 modes M_SCSI 2499 field PPROPT_PACE 0x08 2500 field PPROPT_QAS 0x04 2501 field PPROPT_DT 0x02 2502 field PPROPT_IUT 0x01 2503} 2504 2505/* 2506 * Data Transfer Negotiation Data - Connection Options 2507 */ 2508register NEGCONOPTS { 2509 address 0x064 2510 access_mode RW 2511 modes M_SCSI 2512 field ENSNAPSHOT 0x40 2513 field RTI_WRTDIS 0x20 2514 field RTI_OVRDTRN 0x10 2515 field ENSLOWCRC 0x08 2516 field ENAUTOATNI 0x04 2517 field ENAUTOATNO 0x02 2518 field WIDEXFER 0x01 2519} 2520 2521/* 2522 * Negotiation Table Annex Column Index. 2523 */ 2524register ANNEXCOL { 2525 address 0x065 2526 access_mode RW 2527 modes M_SCSI 2528} 2529 2530register SCSCHKN { 2531 address 0x066 2532 access_mode RW 2533 modes M_CFG 2534 field STSELSKIDDIS 0x40 2535 field CURRFIFODEF 0x20 2536 field WIDERESEN 0x10 2537 field SDONEMSKDIS 0x08 2538 field DFFACTCLR 0x04 2539 field SHVALIDSTDIS 0x02 2540 field LSTSGCLRDIS 0x01 2541} 2542 2543const AHD_ANNEXCOL_PER_DEV0 4 2544const AHD_NUM_PER_DEV_ANNEXCOLS 4 2545const AHD_ANNEXCOL_PRECOMP_SLEW 4 2546const AHD_PRECOMP_MASK 0x07 2547const AHD_PRECOMP_SHIFT 0 2548const AHD_PRECOMP_CUTBACK_17 0x04 2549const AHD_PRECOMP_CUTBACK_29 0x06 2550const AHD_PRECOMP_CUTBACK_37 0x07 2551const AHD_SLEWRATE_MASK 0x78 2552const AHD_SLEWRATE_SHIFT 3 2553/* 2554 * Rev A has only a single bit (high bit of field) of slew adjustment. 2555 * Rev B has 4 bits. The current default happens to be the same for both. 2556 */ 2557const AHD_SLEWRATE_DEF_REVA 0x08 2558const AHD_SLEWRATE_DEF_REVB 0x08 2559 2560/* Rev A does not have any amplitude setting. */ 2561const AHD_ANNEXCOL_AMPLITUDE 6 2562const AHD_AMPLITUDE_MASK 0x7 2563const AHD_AMPLITUDE_SHIFT 0 2564const AHD_AMPLITUDE_DEF 0x7 2565 2566/* 2567 * Negotiation Table Annex Data Port. 2568 */ 2569register ANNEXDAT { 2570 address 0x066 2571 access_mode RW 2572 modes M_SCSI 2573} 2574 2575/* 2576 * Initiator's Own Id. 2577 * The SCSI ID to use for Selection Out and seen during a reselection.. 2578 */ 2579register IOWNID { 2580 address 0x067 2581 access_mode RW 2582 modes M_SCSI 2583} 2584 2585/* 2586 * 960MHz Phase-Locked Loop Control 0 2587 */ 2588register PLL960CTL0 { 2589 address 0x068 2590 access_mode RW 2591 modes M_CFG 2592 field PLL_VCOSEL 0x80 2593 field PLL_PWDN 0x40 2594 field PLL_NS 0x30 2595 field PLL_ENLUD 0x08 2596 field PLL_ENLPF 0x04 2597 field PLL_DLPF 0x02 2598 field PLL_ENFBM 0x01 2599} 2600 2601/* 2602 * Target Own Id 2603 */ 2604register TOWNID { 2605 address 0x069 2606 access_mode RW 2607 modes M_SCSI 2608} 2609 2610/* 2611 * 960MHz Phase-Locked Loop Control 1 2612 */ 2613register PLL960CTL1 { 2614 address 0x069 2615 access_mode RW 2616 modes M_CFG 2617 field PLL_CNTEN 0x80 2618 field PLL_CNTCLR 0x40 2619 field PLL_RST 0x01 2620} 2621 2622/* 2623 * Expander Signature 2624 */ 2625register XSIG { 2626 address 0x06A 2627 access_mode RW 2628 modes M_SCSI 2629} 2630 2631/* 2632 * Shadow Byte Count 2633 */ 2634register SHCNT { 2635 address 0x068 2636 access_mode RW 2637 size 3 2638 modes M_DFF0, M_DFF1 2639} 2640 2641/* 2642 * Selection Out ID 2643 */ 2644register SELOID { 2645 address 0x06B 2646 access_mode RW 2647 modes M_SCSI 2648} 2649 2650/* 2651 * 960-MHz Phase-Locked Loop Test Count 2652 */ 2653register PLL960CNT0 { 2654 address 0x06A 2655 access_mode RO 2656 size 2 2657 modes M_CFG 2658} 2659 2660/* 2661 * 400-MHz Phase-Locked Loop Control 0 2662 */ 2663register PLL400CTL0 { 2664 address 0x06C 2665 access_mode RW 2666 modes M_CFG 2667 field PLL_VCOSEL 0x80 2668 field PLL_PWDN 0x40 2669 field PLL_NS 0x30 2670 field PLL_ENLUD 0x08 2671 field PLL_ENLPF 0x04 2672 field PLL_DLPF 0x02 2673 field PLL_ENFBM 0x01 2674} 2675 2676/* 2677 * Arbitration Fairness 2678 */ 2679register FAIRNESS { 2680 address 0x06C 2681 access_mode RW 2682 size 2 2683 modes M_SCSI 2684} 2685 2686/* 2687 * 400-MHz Phase-Locked Loop Control 1 2688 */ 2689register PLL400CTL1 { 2690 address 0x06D 2691 access_mode RW 2692 modes M_CFG 2693 field PLL_CNTEN 0x80 2694 field PLL_CNTCLR 0x40 2695 field PLL_RST 0x01 2696} 2697 2698/* 2699 * Arbitration Unfairness 2700 */ 2701register UNFAIRNESS { 2702 address 0x06E 2703 access_mode RW 2704 size 2 2705 modes M_SCSI 2706} 2707 2708/* 2709 * 400-MHz Phase-Locked Loop Test Count 2710 */ 2711register PLL400CNT0 { 2712 address 0x06E 2713 access_mode RO 2714 size 2 2715 modes M_CFG 2716} 2717 2718/* 2719 * SCB Page Pointer 2720 */ 2721register SCBPTR { 2722 address 0x0A8 2723 access_mode RW 2724 size 2 2725 modes M_DFF0, M_DFF1, M_CCHAN, M_SCSI 2726} 2727 2728/* 2729 * CMC SCB Array Count 2730 * Number of bytes to transfer between CMC SCB memory and SCBRAM. 2731 * Transfers must be 8byte aligned and sized. 2732 */ 2733register CCSCBACNT { 2734 address 0x0AB 2735 access_mode RW 2736 modes M_CCHAN 2737} 2738 2739/* 2740 * SCB Autopointer 2741 * SCB-Next Address Snooping logic. When an SCB is transferred to 2742 * the card, the next SCB address to be used by the CMC array can 2743 * be autoloaded from that transfer. 2744 */ 2745register SCBAUTOPTR { 2746 address 0x0AB 2747 access_mode RW 2748 modes M_CFG 2749 field AUSCBPTR_EN 0x80 2750 field SCBPTR_ADDR 0x38 2751 field SCBPTR_OFF 0x07 2752} 2753 2754/* 2755 * CMC SG Ram Address Pointer 2756 */ 2757register CCSGADDR { 2758 address 0x0AC 2759 access_mode RW 2760 modes M_DFF0, M_DFF1 2761} 2762 2763/* 2764 * CMC SCB RAM Address Pointer 2765 */ 2766register CCSCBADDR { 2767 address 0x0AC 2768 access_mode RW 2769 modes M_CCHAN 2770} 2771 2772/* 2773 * CMC SCB Ram Back-up Address Pointer 2774 * Indicates the true stop location of transfers halted prior 2775 * to SCBHCNT going to 0. 2776 */ 2777register CCSCBADR_BK { 2778 address 0x0AC 2779 access_mode RO 2780 modes M_CFG 2781} 2782 2783/* 2784 * CMC SG Control 2785 */ 2786register CCSGCTL { 2787 address 0x0AD 2788 access_mode RW 2789 modes M_DFF0, M_DFF1 2790 field CCSGDONE 0x80 2791 field SG_CACHE_AVAIL 0x10 2792 field CCSGENACK 0x08 2793 mask CCSGEN 0x0C 2794 field SG_FETCH_REQ 0x02 2795 field CCSGRESET 0x01 2796} 2797 2798/* 2799 * CMD SCB Control 2800 */ 2801register CCSCBCTL { 2802 address 0x0AD 2803 access_mode RW 2804 modes M_CCHAN 2805 field CCSCBDONE 0x80 2806 field ARRDONE 0x40 2807 field CCARREN 0x10 2808 field CCSCBEN 0x08 2809 field CCSCBDIR 0x04 2810 field CCSCBRESET 0x01 2811} 2812 2813/* 2814 * CMC Ram BIST 2815 */ 2816register CMC_RAMBIST { 2817 address 0x0AD 2818 access_mode RW 2819 modes M_CFG 2820 field SG_ELEMENT_SIZE 0x80 2821 field SCBRAMBIST_FAIL 0x40 2822 field SG_BIST_FAIL 0x20 2823 field SG_BIST_EN 0x10 2824 field CMC_BUFFER_BIST_FAIL 0x02 2825 field CMC_BUFFER_BIST_EN 0x01 2826} 2827 2828/* 2829 * CMC SG RAM Data Port 2830 */ 2831register CCSGRAM { 2832 address 0x0B0 2833 access_mode RW 2834 modes M_DFF0, M_DFF1 2835} 2836 2837/* 2838 * CMC SCB RAM Data Port 2839 */ 2840register CCSCBRAM { 2841 address 0x0B0 2842 access_mode RW 2843 modes M_CCHAN 2844} 2845 2846/* 2847 * Flex DMA Address. 2848 */ 2849register FLEXADR { 2850 address 0x0B0 2851 access_mode RW 2852 size 3 2853 modes M_SCSI 2854} 2855 2856/* 2857 * Flex DMA Byte Count 2858 */ 2859register FLEXCNT { 2860 address 0x0B3 2861 access_mode RW 2862 size 2 2863 modes M_SCSI 2864} 2865 2866/* 2867 * Flex DMA Status 2868 */ 2869register FLEXDMASTAT { 2870 address 0x0B5 2871 access_mode RW 2872 modes M_SCSI 2873 field FLEXDMAERR 0x02 2874 field FLEXDMADONE 0x01 2875} 2876 2877/* 2878 * Flex DMA Data Port 2879 */ 2880register FLEXDATA { 2881 address 0x0B6 2882 access_mode RW 2883 modes M_SCSI 2884} 2885 2886/* 2887 * Board Data 2888 */ 2889register BRDDAT { 2890 address 0x0B8 2891 access_mode RW 2892 modes M_SCSI 2893} 2894 2895/* 2896 * Board Control 2897 */ 2898register BRDCTL { 2899 address 0x0B9 2900 access_mode RW 2901 modes M_SCSI 2902 field FLXARBACK 0x80 2903 field FLXARBREQ 0x40 2904 field BRDADDR 0x38 2905 field BRDEN 0x04 2906 field BRDRW 0x02 2907 field BRDSTB 0x01 2908} 2909 2910/* 2911 * Serial EEPROM Address 2912 */ 2913register SEEADR { 2914 address 0x0BA 2915 access_mode RW 2916 modes M_SCSI 2917} 2918 2919/* 2920 * Serial EEPROM Data 2921 */ 2922register SEEDAT { 2923 address 0x0BC 2924 access_mode RW 2925 size 2 2926 modes M_SCSI 2927} 2928 2929/* 2930 * Serial EEPROM Status 2931 */ 2932register SEESTAT { 2933 address 0x0BE 2934 access_mode RO 2935 modes M_SCSI 2936 field INIT_DONE 0x80 2937 field SEEOPCODE 0x70 2938 field LDALTID_L 0x08 2939 field SEEARBACK 0x04 2940 field SEEBUSY 0x02 2941 field SEESTART 0x01 2942} 2943 2944/* 2945 * Serial EEPROM Control 2946 */ 2947register SEECTL { 2948 address 0x0BE 2949 access_mode RW 2950 modes M_SCSI 2951 field SEEOPCODE 0x70 { 2952 SEEOP_ERASE 0x70, 2953 SEEOP_READ 0x60, 2954 SEEOP_WRITE 0x50, 2955 /* 2956 * The following four commands use special 2957 * addresses for differentiation. 2958 */ 2959 SEEOP_ERAL 0x40 2960 } 2961 mask SEEOP_EWEN 0x40 2962 mask SEEOP_WALL 0x40 2963 mask SEEOP_EWDS 0x40 2964 field SEERST 0x02 2965 field SEESTART 0x01 2966} 2967 2968const SEEOP_ERAL_ADDR 0x80 2969const SEEOP_EWEN_ADDR 0xC0 2970const SEEOP_WRAL_ADDR 0x40 2971const SEEOP_EWDS_ADDR 0x00 2972 2973/* 2974 * SCB Counter 2975 */ 2976register SCBCNT { 2977 address 0x0BF 2978 access_mode RW 2979 modes M_SCSI 2980} 2981 2982/* 2983 * Data FIFO Write Address 2984 * Pointer to the next QWD location to be written to the data FIFO. 2985 */ 2986register DFWADDR { 2987 address 0x0C0 2988 access_mode RW 2989 size 2 2990 modes M_DFF0, M_DFF1 2991} 2992 2993/* 2994 * DSP Filter Control 2995 */ 2996register DSPFLTRCTL { 2997 address 0x0C0 2998 access_mode RW 2999 modes M_CFG 3000 field FLTRDISABLE 0x20 3001 field EDGESENSE 0x10 3002 field DSPFCNTSEL 0x0F 3003} 3004 3005/* 3006 * DSP Data Channel Control 3007 */ 3008register DSPDATACTL { 3009 address 0x0C1 3010 access_mode RW 3011 modes M_CFG 3012 field BYPASSENAB 0x80 3013 field DESQDIS 0x10 3014 field RCVROFFSTDIS 0x04 3015 field XMITOFFSTDIS 0x02 3016} 3017 3018/* 3019 * Data FIFO Read Address 3020 * Pointer to the next QWD location to be read from the data FIFO. 3021 */ 3022register DFRADDR { 3023 address 0x0C2 3024 access_mode RW 3025 size 2 3026 modes M_DFF0, M_DFF1 3027} 3028 3029/* 3030 * DSP REQ Control 3031 */ 3032register DSPREQCTL { 3033 address 0x0C2 3034 access_mode RW 3035 modes M_CFG 3036 field MANREQCTL 0xC0 3037 field MANREQDLY 0x3F 3038} 3039 3040/* 3041 * DSP ACK Control 3042 */ 3043register DSPACKCTL { 3044 address 0x0C3 3045 access_mode RW 3046 modes M_CFG 3047 field MANACKCTL 0xC0 3048 field MANACKDLY 0x3F 3049} 3050 3051/* 3052 * Data FIFO Data 3053 * Read/Write byte port into the data FIFO. The read and write 3054 * FIFO pointers increment with each read and write respectively 3055 * to this port. 3056 */ 3057register DFDAT { 3058 address 0x0C4 3059 access_mode RW 3060 modes M_DFF0, M_DFF1 3061} 3062 3063/* 3064 * DSP Channel Select 3065 */ 3066register DSPSELECT { 3067 address 0x0C4 3068 access_mode RW 3069 modes M_CFG 3070 field AUTOINCEN 0x80 3071 field DSPSEL 0x1F 3072} 3073 3074const NUMDSPS 0x14 3075 3076/* 3077 * Write Bias Control 3078 */ 3079register WRTBIASCTL { 3080 address 0x0C5 3081 access_mode WO 3082 modes M_CFG 3083 field AUTOXBCDIS 0x80 3084 field XMITMANVAL 0x3F 3085} 3086 3087/* 3088 * Currently the WRTBIASCTL is the same as the default. 3089 */ 3090const WRTBIASCTL_HP_DEFAULT 0x0 3091 3092/* 3093 * Receiver Bias Control 3094 */ 3095register RCVRBIOSCTL { 3096 address 0x0C6 3097 access_mode WO 3098 modes M_CFG 3099 field AUTORBCDIS 0x80 3100 field RCVRMANVAL 0x3F 3101} 3102 3103/* 3104 * Write Bias Calculator 3105 */ 3106register WRTBIASCALC { 3107 address 0x0C7 3108 access_mode RO 3109 modes M_CFG 3110} 3111 3112/* 3113 * Data FIFO Pointers 3114 * Contains the byte offset from DFWADDR and DWRADDR to the current 3115 * FIFO write/read locations. 3116 */ 3117register DFPTRS { 3118 address 0x0C8 3119 access_mode RW 3120 modes M_DFF0, M_DFF1 3121} 3122 3123/* 3124 * Receiver Bias Calculator 3125 */ 3126register RCVRBIASCALC { 3127 address 0x0C8 3128 access_mode RO 3129 modes M_CFG 3130} 3131 3132/* 3133 * Data FIFO Backup Read Pointer 3134 * Contains the data FIFO address to be restored if the last 3135 * data accessed from the data FIFO was not transferred successfully. 3136 */ 3137register DFBKPTR { 3138 address 0x0C9 3139 access_mode RW 3140 size 2 3141 modes M_DFF0, M_DFF1 3142} 3143 3144/* 3145 * Skew Calculator 3146 */ 3147register SKEWCALC { 3148 address 0x0C9 3149 access_mode RO 3150 modes M_CFG 3151} 3152 3153/* 3154 * Data FIFO Debug Control 3155 */ 3156register DFDBCTL { 3157 address 0x0CB 3158 access_mode RW 3159 modes M_DFF0, M_DFF1 3160 field DFF_CIO_WR_RDY 0x20 3161 field DFF_CIO_RD_RDY 0x10 3162 field DFF_DIR_ERR 0x08 3163 field DFF_RAMBIST_FAIL 0x04 3164 field DFF_RAMBIST_DONE 0x02 3165 field DFF_RAMBIST_EN 0x01 3166} 3167 3168/* 3169 * Data FIFO Space Count 3170 * Number of FIFO locations that are free. 3171 */ 3172register DFSCNT { 3173 address 0x0CC 3174 access_mode RO 3175 size 2 3176 modes M_DFF0, M_DFF1 3177} 3178 3179/* 3180 * Data FIFO Byte Count 3181 * Number of filled FIFO locations. 3182 */ 3183register DFBCNT { 3184 address 0x0CE 3185 access_mode RO 3186 size 2 3187 modes M_DFF0, M_DFF1 3188} 3189 3190/* 3191 * Sequencer Program Overlay Address. 3192 * Low address must be written prior to high address. 3193 */ 3194register OVLYADDR { 3195 address 0x0D4 3196 modes M_SCSI 3197 size 2 3198 access_mode RW 3199} 3200 3201/* 3202 * Sequencer Control 0 3203 * Error detection mode, speed configuration, 3204 * single step, breakpoints and program load. 3205 */ 3206register SEQCTL0 { 3207 address 0x0D6 3208 access_mode RW 3209 field PERRORDIS 0x80 3210 field PAUSEDIS 0x40 3211 field FAILDIS 0x20 3212 field FASTMODE 0x10 3213 field BRKADRINTEN 0x08 3214 field STEP 0x04 3215 field SEQRESET 0x02 3216 field LOADRAM 0x01 3217} 3218 3219/* 3220 * Sequencer Control 1 3221 * Instruction RAM Diagnostics 3222 */ 3223register SEQCTL1 { 3224 address 0x0D7 3225 access_mode RW 3226 field OVRLAY_DATA_CHK 0x08 3227 field RAMBIST_DONE 0x04 3228 field RAMBIST_FAIL 0x02 3229 field RAMBIST_EN 0x01 3230} 3231 3232/* 3233 * Sequencer Flags 3234 * Zero and Carry state of the ALU. 3235 */ 3236register FLAGS { 3237 address 0x0D8 3238 access_mode RO 3239 field ZERO 0x02 3240 field CARRY 0x01 3241} 3242 3243/* 3244 * Sequencer Interrupt Control 3245 */ 3246register SEQINTCTL { 3247 address 0x0D9 3248 access_mode RW 3249 field INTVEC1DSL 0x80 3250 field INT1_CONTEXT 0x20 3251 field SCS_SEQ_INT1M1 0x10 3252 field SCS_SEQ_INT1M0 0x08 3253 field INTMASK2 0x04 3254 field INTMASK1 0x02 3255 field IRET 0x01 3256} 3257 3258/* 3259 * Sequencer RAM Data Port 3260 * Single byte window into the Sequencer Instruction Ram area starting 3261 * at the address specified by OVLYADDR. To write a full instruction word, 3262 * simply write four bytes in succession. OVLYADDR will increment after the 3263 * most significant instruction byte (the byte with the parity bit) is written. 3264 */ 3265register SEQRAM { 3266 address 0x0DA 3267 access_mode RW 3268} 3269 3270/* 3271 * Sequencer Program Counter 3272 * Low byte must be written prior to high byte. 3273 */ 3274register PRGMCNT { 3275 address 0x0DE 3276 access_mode RW 3277 size 2 3278} 3279 3280/* 3281 * Accumulator 3282 */ 3283register ACCUM { 3284 address 0x0E0 3285 access_mode RW 3286 accumulator 3287} 3288 3289/* 3290 * Source Index Register 3291 * Incrementing index for reads of SINDIR and the destination (low byte only) 3292 * for any immediate operands passed in jmp, jc, jnc, call instructions. 3293 * Example: 3294 * mvi 0xFF call some_routine; 3295 * 3296 * Will set SINDEX[0] to 0xFF and call the routine "some_routine. 3297 */ 3298register SINDEX { 3299 address 0x0E2 3300 access_mode RW 3301 size 2 3302 sindex 3303} 3304 3305/* 3306 * Destination Index Register 3307 * Incrementing index for writes to DINDIR. Can be used as a scratch register. 3308 */ 3309register DINDEX { 3310 address 0x0E4 3311 access_mode RW 3312 size 2 3313} 3314 3315/* 3316 * Break Address 3317 * Sequencer instruction breakpoint address address. 3318 */ 3319register BRKADDR0 { 3320 address 0x0E6 3321 access_mode RW 3322} 3323 3324register BRKADDR1 { 3325 address 0x0E6 3326 access_mode RW 3327 field BRKDIS 0x80 /* Disable Breakpoint */ 3328} 3329 3330/* 3331 * All Ones 3332 * All reads to this register return the value 0xFF. 3333 */ 3334register ALLONES { 3335 address 0x0E8 3336 access_mode RO 3337 allones 3338} 3339 3340/* 3341 * All Zeros 3342 * All reads to this register return the value 0. 3343 */ 3344register ALLZEROS { 3345 address 0x0EA 3346 access_mode RO 3347 allzeros 3348} 3349 3350/* 3351 * No Destination 3352 * Writes to this register have no effect. 3353 */ 3354register NONE { 3355 address 0x0EA 3356 access_mode WO 3357 none 3358} 3359 3360/* 3361 * Source Index Indirect 3362 * Reading this register is equivalent to reading (register_base + SINDEX) and 3363 * incrementing SINDEX by 1. 3364 */ 3365register SINDIR { 3366 address 0x0EC 3367 access_mode RO 3368} 3369 3370/* 3371 * Destination Index Indirect 3372 * Writing this register is equivalent to writing to (register_base + DINDEX) 3373 * and incrementing DINDEX by 1. 3374 */ 3375register DINDIR { 3376 address 0x0ED 3377 access_mode WO 3378} 3379 3380/* 3381 * Function One 3382 * 2's complement to bit value conversion. Write the 2's complement value 3383 * (0-7 only) to the top nibble and retrieve the bit indexed by that value 3384 * on the next read of this register. 3385 * Example: 3386 * Write 0x60 3387 * Read 0x40 3388 */ 3389register FUNCTION1 { 3390 address 0x0F0 3391 access_mode RW 3392} 3393 3394/* 3395 * Stack 3396 * Window into the stack. Each stack location is 10 bits wide reported 3397 * low byte followed by high byte. There are 8 stack locations. 3398 */ 3399register STACK { 3400 address 0x0F2 3401 access_mode RW 3402} 3403 3404/* 3405 * Interrupt Vector 1 Address 3406 * Interrupt branch address for SCS SEQ_INT1 mode 0 and 1 interrupts. 3407 */ 3408register INTVEC1_ADDR { 3409 address 0x0F4 3410 access_mode RW 3411 size 2 3412 modes M_CFG 3413} 3414 3415/* 3416 * Current Address 3417 * Address of the SEQRAM instruction currently executing instruction. 3418 */ 3419register CURADDR { 3420 address 0x0F4 3421 access_mode RW 3422 size 2 3423 modes M_SCSI 3424} 3425 3426/* 3427 * Interrupt Vector 2 Address 3428 * Interrupt branch address for HST_SEQ_INT2 interrupts. 3429 */ 3430register INTVEC2_ADDR { 3431 address 0x0F6 3432 access_mode RW 3433 size 2 3434 modes M_CFG 3435} 3436 3437/* 3438 * Last Address 3439 * Address of the SEQRAM instruction executed prior to the current instruction. 3440 */ 3441register LASTADDR { 3442 address 0x0F6 3443 access_mode RW 3444 size 2 3445 modes M_SCSI 3446} 3447 3448register AHD_PCI_CONFIG_BASE { 3449 address 0x100 3450 access_mode RW 3451 size 256 3452 modes M_CFG 3453} 3454 3455/* ---------------------- Scratch RAM Offsets ------------------------- */ 3456scratch_ram { 3457 /* Mode Specific */ 3458 address 0x0A0 3459 size 8 3460 modes 0, 1, 2, 3 3461 REG0 { 3462 size 2 3463 } 3464 REG1 { 3465 size 2 3466 } 3467 REG_ISR { 3468 size 2 3469 } 3470 SG_STATE { 3471 size 1 3472 field SEGS_AVAIL 0x01 3473 field LOADING_NEEDED 0x02 3474 field FETCH_INPROG 0x04 3475 } 3476 /* 3477 * Track whether the transfer byte count for 3478 * the current data phase is odd. 3479 */ 3480 DATA_COUNT_ODD { 3481 size 1 3482 } 3483} 3484 3485scratch_ram { 3486 /* Mode Specific */ 3487 address 0x0F8 3488 size 8 3489 modes 0, 1, 2, 3 3490 LONGJMP_ADDR { 3491 size 2 3492 } 3493 ACCUM_SAVE { 3494 size 1 3495 } 3496} 3497 3498 3499scratch_ram { 3500 address 0x100 3501 size 128 3502 modes 0, 1, 2, 3 3503 /* 3504 * Per "other-id" execution queues. We use an array of 3505 * tail pointers into lists of SCBs sorted by "other-id". 3506 * The execution head pointer threads the head SCBs for 3507 * each list. 3508 */ 3509 WAITING_SCB_TAILS { 3510 size 32 3511 } 3512 WAITING_TID_HEAD { 3513 size 2 3514 } 3515 WAITING_TID_TAIL { 3516 size 2 3517 } 3518 /* 3519 * SCBID of the next SCB in the new SCB queue. 3520 */ 3521 NEXT_QUEUED_SCB_ADDR { 3522 size 4 3523 } 3524 /* 3525 * head of list of SCBs that have 3526 * completed but have not been 3527 * put into the qoutfifo. 3528 */ 3529 COMPLETE_SCB_HEAD { 3530 size 2 3531 } 3532 /* 3533 * The list of completed SCBs in 3534 * the active DMA. 3535 */ 3536 COMPLETE_SCB_DMAINPROG_HEAD { 3537 size 2 3538 } 3539 /* 3540 * head of list of SCBs that have 3541 * completed but need to be uploaded 3542 * to the host prior to being completed. 3543 */ 3544 COMPLETE_DMA_SCB_HEAD { 3545 size 2 3546 } 3547 /* Counting semaphore to prevent new select-outs */ 3548 QFREEZE_COUNT { 3549 size 2 3550 } 3551 /* 3552 * Mode to restore on legacy idle loop exit. 3553 */ 3554 SAVED_MODE { 3555 size 1 3556 } 3557 /* 3558 * Single byte buffer used to designate the type or message 3559 * to send to a target. 3560 */ 3561 MSG_OUT { 3562 size 1 3563 } 3564 /* Parameters for DMA Logic */ 3565 DMAPARAMS { 3566 size 1 3567 field PRELOADEN 0x80 3568 field WIDEODD 0x40 3569 field SCSIEN 0x20 3570 field SDMAEN 0x10 3571 field SDMAENACK 0x10 3572 field HDMAEN 0x08 3573 field HDMAENACK 0x08 3574 field DIRECTION 0x04 /* Set indicates PCI->SCSI */ 3575 field FIFOFLUSH 0x02 3576 field FIFORESET 0x01 3577 } 3578 SEQ_FLAGS { 3579 size 1 3580 field NOT_IDENTIFIED 0x80 3581 field NO_CDB_SENT 0x40 3582 field TARGET_CMD_IS_TAGGED 0x40 3583 field DPHASE 0x20 3584 /* Target flags */ 3585 field TARG_CMD_PENDING 0x10 3586 field CMDPHASE_PENDING 0x08 3587 field DPHASE_PENDING 0x04 3588 field SPHASE_PENDING 0x02 3589 field NO_DISCONNECT 0x01 3590 } 3591 /* 3592 * Temporary storage for the 3593 * target/channel/lun of a 3594 * reconnecting target 3595 */ 3596 SAVED_SCSIID { 3597 size 1 3598 } 3599 SAVED_LUN { 3600 size 1 3601 } 3602 /* 3603 * The last bus phase as seen by the sequencer. 3604 */ 3605 LASTPHASE { 3606 size 1 3607 field CDI 0x80 3608 field IOI 0x40 3609 field MSGI 0x20 3610 field P_BUSFREE 0x01 3611 enum PHASE_MASK CDO|IOO|MSGO { 3612 P_DATAOUT 0x0, 3613 P_DATAIN IOO, 3614 P_DATAOUT_DT P_DATAOUT|MSGO, 3615 P_DATAIN_DT P_DATAIN|MSGO, 3616 P_COMMAND CDO, 3617 P_MESGOUT CDO|MSGO, 3618 P_STATUS CDO|IOO, 3619 P_MESGIN CDO|IOO|MSGO 3620 } 3621 } 3622 /* 3623 * Value to "or" into the SCBPTR[1] value to 3624 * indicate that an entry in the QINFIFO is valid. 3625 */ 3626 QOUTFIFO_ENTRY_VALID_TAG { 3627 size 1 3628 } 3629 /* 3630 * Base address of our shared data with the kernel driver in host 3631 * memory. This includes the qoutfifo and target mode 3632 * incoming command queue. 3633 */ 3634 SHARED_DATA_ADDR { 3635 size 4 3636 } 3637 /* 3638 * Pointer to location in host memory for next 3639 * position in the qoutfifo. 3640 */ 3641 QOUTFIFO_NEXT_ADDR { 3642 size 4 3643 } 3644 /* 3645 * Kernel and sequencer offsets into the queue of 3646 * incoming target mode command descriptors. The 3647 * queue is full when the KERNEL_TQINPOS == TQINPOS. 3648 */ 3649 KERNEL_TQINPOS { 3650 size 1 3651 } 3652 TQINPOS { 3653 size 1 3654 } 3655 ARG_1 { 3656 size 1 3657 mask SEND_MSG 0x80 3658 mask SEND_SENSE 0x40 3659 mask SEND_REJ 0x20 3660 mask MSGOUT_PHASEMIS 0x10 3661 mask EXIT_MSG_LOOP 0x08 3662 mask CONT_MSG_LOOP_WRITE 0x04 3663 mask CONT_MSG_LOOP_READ 0x03 3664 mask CONT_MSG_LOOP_TARG 0x02 3665 alias RETURN_1 3666 } 3667 ARG_2 { 3668 size 1 3669 alias RETURN_2 3670 } 3671 3672 /* 3673 * Snapshot of MSG_OUT taken after each message is sent. 3674 */ 3675 LAST_MSG { 3676 size 1 3677 } 3678 3679 /* 3680 * Sequences the kernel driver has okayed for us. This allows 3681 * the driver to do things like prevent initiator or target 3682 * operations. 3683 */ 3684 SCSISEQ_TEMPLATE { 3685 size 1 3686 field MANUALCTL 0x40 3687 field ENSELI 0x20 3688 field ENRSELI 0x10 3689 field MANUALP 0x0C 3690 field ENAUTOATNP 0x02 3691 field ALTSTIM 0x01 3692 } 3693 3694 /* 3695 * The initiator specified tag for this target mode transaction. 3696 */ 3697 INITIATOR_TAG { 3698 size 1 3699 } 3700 3701 SEQ_FLAGS2 { 3702 size 1 3703 field TARGET_MSG_PENDING 0x02 3704 field SELECTOUT_QFROZEN 0x04 3705 } 3706 3707 ALLOCFIFO_SCBPTR { 3708 size 2 3709 } 3710 3711 /* 3712 * The maximum amount of time to wait, when interrupt coalescing 3713 * is enabled, before issueing a CMDCMPLT interrupt for a completed 3714 * command. 3715 */ 3716 INT_COALESCING_TIMER { 3717 size 2 3718 } 3719 3720 /* 3721 * The maximum number of commands to coalesce into a single interrupt. 3722 * Actually the 2's complement of that value to simplify sequencer 3723 * code. 3724 */ 3725 INT_COALESCING_MAXCMDS { 3726 size 1 3727 } 3728 3729 /* 3730 * The minimum number of commands still outstanding required 3731 * to continue coalescing (2's complement of value). 3732 */ 3733 INT_COALESCING_MINCMDS { 3734 size 1 3735 } 3736 3737 /* 3738 * Number of commands "in-flight". 3739 */ 3740 CMDS_PENDING { 3741 size 2 3742 } 3743 3744 /* 3745 * The count of commands that have been coalesced. 3746 */ 3747 INT_COALESCING_CMDCOUNT { 3748 size 1 3749 } 3750 3751 /* 3752 * Since the HS_MAIBOX is self clearing, copy its contents to 3753 * this position in scratch ram every time it changes. 3754 */ 3755 LOCAL_HS_MAILBOX { 3756 size 1 3757 } 3758 /* 3759 * Target-mode CDB type to CDB length table used 3760 * in non-packetized operation. 3761 */ 3762 CMDSIZE_TABLE { 3763 size 8 3764 } 3765} 3766 3767/************************* Hardware SCB Definition ****************************/ 3768scb { 3769 address 0x180 3770 size 64 3771 modes 0, 1, 2, 3 3772 SCB_RESIDUAL_DATACNT { 3773 size 4 3774 alias SCB_CDB_STORE 3775 alias SCB_HOST_CDB_PTR 3776 } 3777 SCB_RESIDUAL_SGPTR { 3778 size 4 3779 field SG_ADDR_MASK 0xf8 /* In the last byte */ 3780 field SG_OVERRUN_RESID 0x02 /* In the first byte */ 3781 field SG_LIST_NULL 0x01 /* In the first byte */ 3782 } 3783 SCB_SCSI_STATUS { 3784 size 1 3785 alias SCB_HOST_CDB_LEN 3786 } 3787 SCB_TARGET_PHASES { 3788 size 1 3789 } 3790 SCB_TARGET_DATA_DIR { 3791 size 1 3792 } 3793 SCB_TARGET_ITAG { 3794 size 1 3795 } 3796 SCB_SENSE_BUSADDR { 3797 /* 3798 * Only valid if CDB length is less than 13 bytes or 3799 * we are using a CDB pointer. Otherwise contains 3800 * the last 4 bytes of embedded cdb information. 3801 */ 3802 size 4 3803 alias SCB_NEXT_COMPLETE 3804 } 3805 SCB_TAG { 3806 alias SCB_FIFO_USE_COUNT 3807 size 2 3808 } 3809 SCB_CONTROL { 3810 size 1 3811 field TARGET_SCB 0x80 3812 field DISCENB 0x40 3813 field TAG_ENB 0x20 3814 field MK_MESSAGE 0x10 3815 field STATUS_RCVD 0x08 3816 field DISCONNECTED 0x04 3817 field SCB_TAG_TYPE 0x03 3818 } 3819 SCB_SCSIID { 3820 size 1 3821 field TID 0xF0 3822 field OID 0x0F 3823 } 3824 SCB_LUN { 3825 size 1 3826 field LID 0xff 3827 } 3828 SCB_TASK_ATTRIBUTE { 3829 size 1 3830 /* 3831 * Overloaded field for non-packetized 3832 * ignore wide residue message handling. 3833 */ 3834 field SCB_XFERLEN_ODD 0x01 3835 } 3836 SCB_CDB_LEN { 3837 size 1 3838 field SCB_CDB_LEN_PTR 0x80 /* CDB in host memory */ 3839 } 3840 SCB_TASK_MANAGEMENT { 3841 size 1 3842 } 3843 SCB_DATAPTR { 3844 size 8 3845 } 3846 SCB_DATACNT { 3847 /* 3848 * The last byte is really the high address bits for 3849 * the data address. 3850 */ 3851 size 4 3852 field SG_LAST_SEG 0x80 /* In the fourth byte */ 3853 field SG_HIGH_ADDR_BITS 0x7F /* In the fourth byte */ 3854 } 3855 SCB_SGPTR { 3856 size 4 3857 field SG_STATUS_VALID 0x04 /* In the first byte */ 3858 field SG_FULL_RESID 0x02 /* In the first byte */ 3859 field SG_LIST_NULL 0x01 /* In the first byte */ 3860 } 3861 SCB_BUSADDR { 3862 size 4 3863 } 3864 SCB_NEXT { 3865 alias SCB_NEXT_SCB_BUSADDR 3866 size 2 3867 } 3868 SCB_NEXT2 { 3869 size 2 3870 } 3871 SCB_SPARE { 3872 size 8 3873 alias SCB_PKT_LUN 3874 } 3875 SCB_DISCONNECTED_LISTS { 3876 size 8 3877 } 3878} 3879 3880/*********************************** Constants ********************************/ 3881const MK_MESSAGE_BIT_OFFSET 4 3882const TID_SHIFT 4 3883const TARGET_CMD_CMPLT 0xfe 3884const INVALID_ADDR 0x80 3885#define SCB_LIST_NULL 0xff 3886#define QOUTFIFO_ENTRY_VALID_TOGGLE 0x80 3887 3888const CCSGADDR_MAX 0x80 3889const CCSCBADDR_MAX 0x80 3890const CCSGRAM_MAXSEGS 16 3891 3892/* Selection Timeout Timer Constants */ 3893const STIMESEL_SHIFT 3 3894const STIMESEL_MIN 0x18 3895const STIMESEL_BUG_ADJ 0x8 3896 3897/* WDTR Message values */ 3898const BUS_8_BIT 0x00 3899const BUS_16_BIT 0x01 3900const BUS_32_BIT 0x02 3901 3902/* Offset maximums */ 3903const MAX_OFFSET 0xfe 3904const MAX_OFFSET_PACED 0xfe 3905const MAX_OFFSET_PACED_BUG 0x7f 3906/* 3907 * Some 160 devices incorrectly accept 0xfe as a 3908 * sync offset, but will overrun this value. Limit 3909 * to 0x7f for speed lower than U320 which will 3910 * avoid the persistent sync offset overruns. 3911 */ 3912const MAX_OFFSET_NON_PACED 0x7f 3913const HOST_MSG 0xff 3914 3915/* 3916 * The size of our sense buffers. 3917 * Sense buffer mapping can be handled in either of two ways. 3918 * The first is to allocate a dmamap for each transaction. 3919 * Depending on the architecture, dmamaps can be costly. The 3920 * alternative is to statically map the buffers in much the same 3921 * way we handle our scatter gather lists. The driver implements 3922 * the later. 3923 */ 3924const AHD_SENSE_BUFSIZE 256 3925 3926/* Target mode command processing constants */ 3927const CMD_GROUP_CODE_SHIFT 0x05 3928 3929const STATUS_BUSY 0x08 3930const STATUS_QUEUE_FULL 0x28 3931const STATUS_PKT_SENSE 0xFF 3932const TARGET_DATA_IN 1 3933 3934const SCB_TRANSFER_SIZE_FULL_LUN 56 3935const SCB_TRANSFER_SIZE_1BYTE_LUN 48 3936/* PKT_OVERRUN_BUFSIZE must be a multiple of 256 less than 64K */ 3937const PKT_OVERRUN_BUFSIZE 512 3938 3939/* 3940 * Timer parameters. 3941 */ 3942const AHD_TIMER_US_PER_TICK 25 3943const AHD_TIMER_MAX_TICKS 0xFFFF 3944const AHD_TIMER_MAX_US (AHD_TIMER_MAX_TICKS * AHD_TIMER_US_PER_TICK) 3945 3946/* 3947 * Downloaded (kernel inserted) constants 3948 */ 3949const SG_PREFETCH_CNT download 3950const SG_PREFETCH_CNT_LIMIT download 3951const SG_PREFETCH_ALIGN_MASK download 3952const SG_PREFETCH_ADDR_MASK download 3953const SG_SIZEOF download 3954const PKT_OVERRUN_BUFOFFSET download 3955const SCB_TRANSFER_SIZE download 3956 3957/* 3958 * BIOS SCB offsets 3959 */ 3960const NVRAM_SCB_OFFSET 0x2C 3961