1/* $NetBSD: aic79xx.seq,v 1.10 2005/12/11 12:22:18 christos Exp $ */ 2 3/* 4 * Adaptec U320 device driver firmware for Linux and FreeBSD. 5 * 6 * Copyright (c) 1994-2001 Justin T. Gibbs. 7 * Copyright (c) 2000-2002 Adaptec Inc. 8 * All rights reserved. 9 * 10 * Redistribution and use in source and binary forms, with or without 11 * modification, are permitted provided that the following conditions 12 * are met: 13 * 1. Redistributions of source code must retain the above copyright 14 * notice, this list of conditions, and the following disclaimer, 15 * without modification. 16 * 2. Redistributions in binary form must reproduce at minimum a disclaimer 17 * substantially similar to the "NO WARRANTY" disclaimer below 18 * ("Disclaimer") and any redistribution must be conditioned upon 19 * including a substantially similar Disclaimer requirement for further 20 * binary redistribution. 21 * 3. Neither the names of the above-listed copyright holders nor the names 22 * of any contributors may be used to endorse or promote products derived 23 * from this software without specific prior written permission. 24 * 25 * Alternatively, this software may be distributed under the terms of the 26 * GNU General Public License ("GPL") version 2 as published by the Free 27 * Software Foundation. 28 * 29 * NO WARRANTY 30 * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS 31 * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT 32 * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTIBILITY AND FITNESS FOR 33 * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT 34 * HOLDERS OR CONTRIBUTORS BE LIABLE FOR SPECIAL, EXEMPLARY, OR CONSEQUENTIAL 35 * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS 36 * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) 37 * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, 38 * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING 39 * IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE 40 * POSSIBILITY OF SUCH DAMAGES. 41 * 42 * $FreeBSD: src/sys/dev/aic7xxx/aic79xx.seq,v 1.13 2003/06/28 04:44:10 gibbs Exp $ 43 */ 44 45VERSION = "Id: //depot/aic7xxx/aic7xxx/aic79xx.seq#96 $" 46PATCH_ARG_LIST = "struct ahd_softc *ahd" 47PREFIX = "ahd_" 48 49#include <dev/microcode/aic7xxx/aic79xx.reg> 50#include <dev/scsipi/scsi_message.h> 51 52restart: 53if ((ahd->bugs & AHD_INTCOLLISION_BUG) != 0) { 54 test SEQINTCODE, 0xFF jz idle_loop; 55 SET_SEQINTCODE(NO_SEQINT) 56} 57 58idle_loop: 59 60 if ((ahd->bugs & AHD_INTCOLLISION_BUG) != 0) { 61 /* 62 * Convert ERROR status into a sequencer 63 * interrupt to handle the case of an 64 * interrupt collision on the hardware 65 * setting of HWERR. 66 */ 67 test ERROR, 0xFF jz no_error_set; 68 SET_SEQINTCODE(SAW_HWERR) 69no_error_set: 70 } 71 SET_MODE(M_SCSI, M_SCSI) 72 test SCSISEQ0, ENSELO|ENARBO jnz idle_loop_checkbus; 73 test SEQ_FLAGS2, SELECTOUT_QFROZEN jnz idle_loop_checkbus; 74 cmp WAITING_TID_HEAD[1], SCB_LIST_NULL je idle_loop_checkbus; 75 /* 76 * ENSELO is cleared by a SELDO, so we must test for SELDO 77 * one last time. 78 */ 79BEGIN_CRITICAL; 80 test SSTAT0, SELDO jnz select_out; 81END_CRITICAL; 82 call start_selection; 83idle_loop_checkbus: 84BEGIN_CRITICAL; 85 test SSTAT0, SELDO jnz select_out; 86END_CRITICAL; 87 test SSTAT0, SELDI jnz select_in; 88 test SCSIPHASE, ~DATA_PHASE_MASK jz idle_loop_check_nonpackreq; 89 test SCSISIGO, ATNO jz idle_loop_check_nonpackreq; 90 call unexpected_nonpkt_phase_find_ctxt; 91idle_loop_check_nonpackreq: 92 test SSTAT2, NONPACKREQ jz . + 2; 93 call unexpected_nonpkt_phase_find_ctxt; 94 if ((ahd->bugs & AHD_FAINT_LED_BUG) != 0) { 95 and A, FIFO0FREE|FIFO1FREE, DFFSTAT; 96 cmp A, FIFO0FREE|FIFO1FREE jne . + 3; 97 and SBLKCTL, ~DIAGLEDEN|DIAGLEDON; 98 jmp . + 2; 99 or SBLKCTL, DIAGLEDEN|DIAGLEDON; 100 } 101 call idle_loop_gsfifo_in_scsi_mode; 102 call idle_loop_service_fifos; 103 call idle_loop_cchan; 104 jmp idle_loop; 105 106BEGIN_CRITICAL; 107idle_loop_gsfifo: 108 SET_MODE(M_SCSI, M_SCSI) 109idle_loop_gsfifo_in_scsi_mode: 110 test LQISTAT2, LQIGSAVAIL jz return; 111 /* 112 * We have received good status for this transaction. There may 113 * still be data in our FIFOs draining to the host. Complete 114 * the SCB only if all data has transferred to the host. 115 */ 116good_status_IU_done: 117 bmov SCBPTR, GSFIFO, 2; 118 clr SCB_SCSI_STATUS; 119 /* 120 * If a command completed before an attempted task management 121 * function completed, notify the host after disabling any 122 * pending select-outs. 123 */ 124 test SCB_TASK_MANAGEMENT, 0xFF jz gsfifo_complete_normally; 125 test SSTAT0, SELDO|SELINGO jnz . + 2; 126 and SCSISEQ0, ~ENSELO; 127 SET_SEQINTCODE(TASKMGMT_CMD_CMPLT_OKAY) 128gsfifo_complete_normally: 129 or SCB_CONTROL, STATUS_RCVD; 130 131 /* 132 * Since this status did not consume a FIFO, we have to 133 * be a bit more dilligent in how we check for FIFOs pertaining 134 * to this transaction. There are two states that a FIFO still 135 * transferring data may be in. 136 * 137 * 1) Configured and draining to the host, with a FIFO handler. 138 * 2) Pending cfg4data, fifo not empty. 139 * 140 * Case 1 can be detected by noticing a non-zero FIFO active 141 * count in the SCB. In this case, we allow the routine servicing 142 * the FIFO to complete the SCB. 143 * 144 * Case 2 implies either a pending or yet to occur save data 145 * pointers for this same context in the other FIFO. So, if 146 * we detect case 1, we will properly defer the post of the SCB 147 * and achieve the desired result. The pending cfg4data will 148 * notice that status has been received and complete the SCB. 149 */ 150 test SCB_FIFO_USE_COUNT, 0xFF jnz idle_loop_gsfifo_in_scsi_mode; 151 call complete; 152END_CRITICAL; 153 jmp idle_loop_gsfifo_in_scsi_mode; 154 155idle_loop_service_fifos: 156 SET_MODE(M_DFF0, M_DFF0) 157 test LONGJMP_ADDR[1], INVALID_ADDR jnz idle_loop_next_fifo; 158 call longjmp; 159idle_loop_next_fifo: 160 SET_MODE(M_DFF1, M_DFF1) 161 test LONGJMP_ADDR[1], INVALID_ADDR jz longjmp; 162return: 163 ret; 164 165idle_loop_cchan: 166 SET_MODE(M_CCHAN, M_CCHAN) 167 test QOFF_CTLSTA, HS_MAILBOX_ACT jz hs_mailbox_empty; 168 mov LOCAL_HS_MAILBOX, HS_MAILBOX; 169 or QOFF_CTLSTA, HS_MAILBOX_ACT; 170hs_mailbox_empty: 171BEGIN_CRITICAL; 172 test CCSCBCTL, CCARREN|CCSCBEN jz scbdma_idle; 173 test CCSCBCTL, CCSCBDIR jnz fetch_new_scb_inprog; 174 test CCSCBCTL, CCSCBDONE jz return; 175END_CRITICAL; 176 /* FALLTHROUGH */ 177scbdma_tohost_done: 178 test CCSCBCTL, CCARREN jz fill_qoutfifo_dmadone; 179 /* 180 * An SCB has been succesfully uploaded to the host. 181 * If the SCB was uploaded for some reason other than 182 * bad SCSI status (currently only for underruns), we 183 * queue the SCB for normal completion. Otherwise, we 184 * wait until any select-out activity has halted, and 185 * then notify the host so that the transaction can be 186 * dealt with. 187 */ 188 test SCB_SCSI_STATUS, 0xff jnz scbdma_notify_host; 189 and CCSCBCTL, ~(CCARREN|CCSCBEN); 190 bmov COMPLETE_DMA_SCB_HEAD, SCB_NEXT_COMPLETE, 2; 191 bmov SCB_NEXT_COMPLETE, COMPLETE_SCB_HEAD, 2; 192 bmov COMPLETE_SCB_HEAD, SCBPTR, 2 ret; 193scbdma_notify_host: 194 SET_MODE(M_SCSI, M_SCSI) 195 test SCSISEQ0, ENSELO jnz return; 196 test SSTAT0, (SELDO|SELINGO) jnz return; 197 SET_MODE(M_CCHAN, M_CCHAN) 198 /* 199 * Remove SCB and notify host. 200 */ 201 and CCSCBCTL, ~(CCARREN|CCSCBEN); 202 bmov COMPLETE_DMA_SCB_HEAD, SCB_NEXT_COMPLETE, 2; 203 SET_SEQINTCODE(BAD_SCB_STATUS) 204 ret; 205fill_qoutfifo_dmadone: 206 and CCSCBCTL, ~(CCARREN|CCSCBEN); 207 call qoutfifo_updated; 208 mvi COMPLETE_SCB_DMAINPROG_HEAD[1], SCB_LIST_NULL; 209 bmov QOUTFIFO_NEXT_ADDR, SCBHADDR, 4; 210 test QOFF_CTLSTA, SDSCB_ROLLOVR jz return; 211 bmov QOUTFIFO_NEXT_ADDR, SHARED_DATA_ADDR, 4; 212 xor QOUTFIFO_ENTRY_VALID_TAG, QOUTFIFO_ENTRY_VALID_TOGGLE ret; 213 214qoutfifo_updated: 215 /* 216 * If there are more commands waiting to be DMA'ed 217 * to the host, always coalesce. Otherwise honor the 218 * host's wishes. 219 */ 220 cmp COMPLETE_DMA_SCB_HEAD[1], SCB_LIST_NULL jne coalesce_by_count; 221 cmp COMPLETE_SCB_HEAD[1], SCB_LIST_NULL jne coalesce_by_count; 222 test LOCAL_HS_MAILBOX, ENINT_COALESCE jz issue_cmdcmplt; 223 224 /* 225 * If we have relatively few commands outstanding, don't 226 * bother waiting for another command to complete. 227 */ 228 test CMDS_PENDING[1], 0xFF jnz coalesce_by_count; 229 /* Add -1 so that jnc means <= not just < */ 230 add A, -1, INT_COALESCING_MINCMDS; 231 add NONE, A, CMDS_PENDING; 232 jnc issue_cmdcmplt; 233 234 /* 235 * If coalescing, only coalesce up to the limit 236 * provided by the host driver. 237 */ 238coalesce_by_count: 239 mov A, INT_COALESCING_MAXCMDS; 240 add NONE, A, INT_COALESCING_CMDCOUNT; 241 jc issue_cmdcmplt; 242 /* 243 * If the timer is not currently active, 244 * fire it up. 245 */ 246 test INTCTL, SWTMINTMASK jz return; 247 bmov SWTIMER, INT_COALESCING_TIMER, 2; 248 mvi CLRSEQINTSTAT, CLRSEQ_SWTMRTO; 249 or INTCTL, SWTMINTEN|SWTIMER_START; 250 and INTCTL, ~SWTMINTMASK ret; 251 252issue_cmdcmplt: 253 mvi INTSTAT, CMDCMPLT; 254 clr INT_COALESCING_CMDCOUNT; 255 or INTCTL, SWTMINTMASK ret; 256 257BEGIN_CRITICAL; 258fetch_new_scb_inprog: 259 test CCSCBCTL, ARRDONE jz return; 260fetch_new_scb_done: 261 and CCSCBCTL, ~(CCARREN|CCSCBEN); 262 bmov REG0, SCBPTR, 2; 263 clr A; 264 add CMDS_PENDING, 1; 265 adc CMDS_PENDING[1], A; 266 if ((ahd->bugs & AHD_PKT_LUN_BUG) != 0) { 267 /* 268 * "Short Luns" are not placed into outgoing LQ 269 * packets in the correct byte order. Use a full 270 * sized lun field instead and fill it with the 271 * one byte of lun information we support. 272 */ 273 mov SCB_PKT_LUN[6], SCB_LUN; 274 } 275 /* 276 * The FIFO use count field is shared with the 277 * tag set by the host so that our SCB dma engine 278 * knows the correct location to store the SCB. 279 * Set it to zero before processing the SCB. 280 */ 281 clr SCB_FIFO_USE_COUNT; 282 /* Update the next SCB address to download. */ 283 bmov NEXT_QUEUED_SCB_ADDR, SCB_NEXT_SCB_BUSADDR, 4; 284 mvi SCB_NEXT[1], SCB_LIST_NULL; 285 mvi SCB_NEXT2[1], SCB_LIST_NULL; 286 /* Increment our position in the QINFIFO. */ 287 mov NONE, SNSCB_QOFF; 288 /* 289 * SCBs that want to send messages are always 290 * queued independently. This ensures that they 291 * are at the head of the SCB list to select out 292 * to a target and we will see the MK_MESSAGE flag. 293 */ 294 test SCB_CONTROL, MK_MESSAGE jnz first_new_target_scb; 295 shr SINDEX, 3, SCB_SCSIID; 296 and SINDEX, ~0x1; 297 mvi SINDEX[1], (WAITING_SCB_TAILS >> 8); 298 bmov DINDEX, SINDEX, 2; 299 bmov SCBPTR, SINDIR, 2; 300 bmov DINDIR, REG0, 2; 301 cmp SCBPTR[1], SCB_LIST_NULL je first_new_target_scb; 302 bmov SCB_NEXT, REG0, 2 ret; 303first_new_target_scb: 304 cmp WAITING_TID_HEAD[1], SCB_LIST_NULL je first_new_scb; 305 bmov SCBPTR, WAITING_TID_TAIL, 2; 306 bmov SCB_NEXT2, REG0, 2; 307 bmov WAITING_TID_TAIL, REG0, 2 ret; 308first_new_scb: 309 bmov WAITING_TID_HEAD, REG0, 2; 310 bmov WAITING_TID_TAIL, REG0, 2 ret; 311END_CRITICAL; 312 313scbdma_idle: 314 /* 315 * Give precedence to downloading new SCBs to execute 316 * unless select-outs are currently frozen. 317 */ 318 test SEQ_FLAGS2, SELECTOUT_QFROZEN jnz . + 2; 319BEGIN_CRITICAL; 320 test QOFF_CTLSTA, NEW_SCB_AVAIL jnz fetch_new_scb; 321 cmp COMPLETE_DMA_SCB_HEAD[1], SCB_LIST_NULL jne dma_complete_scb; 322 cmp COMPLETE_SCB_HEAD[1], SCB_LIST_NULL je return; 323 /* FALLTHROUGH */ 324fill_qoutfifo: 325 /* 326 * Keep track of the SCBs we are DMA'ing just 327 * in case the DMA fails or is aborted. 328 */ 329 mov A, QOUTFIFO_ENTRY_VALID_TAG; 330 bmov COMPLETE_SCB_DMAINPROG_HEAD, COMPLETE_SCB_HEAD, 2; 331 mvi CCSCBCTL, CCSCBRESET; 332 bmov SCBHADDR, QOUTFIFO_NEXT_ADDR, 4; 333 bmov SCBPTR, COMPLETE_SCB_HEAD, 2; 334fill_qoutfifo_loop: 335 mov CCSCBRAM, SCBPTR; 336 or CCSCBRAM, A, SCBPTR[1]; 337 mov NONE, SDSCB_QOFF; 338 inc INT_COALESCING_CMDCOUNT; 339 add CMDS_PENDING, -1; 340 adc CMDS_PENDING[1], -1; 341 cmp SCB_NEXT_COMPLETE[1], SCB_LIST_NULL je fill_qoutfifo_done; 342 cmp CCSCBADDR, CCSCBADDR_MAX je fill_qoutfifo_done; 343 test QOFF_CTLSTA, SDSCB_ROLLOVR jnz fill_qoutfifo_done; 344 bmov SCBPTR, SCB_NEXT_COMPLETE, 2; 345 jmp fill_qoutfifo_loop; 346fill_qoutfifo_done: 347 mov SCBHCNT, CCSCBADDR; 348 mvi CCSCBCTL, CCSCBEN|CCSCBRESET; 349 bmov COMPLETE_SCB_HEAD, SCB_NEXT_COMPLETE, 2; 350 mvi SCB_NEXT_COMPLETE[1], SCB_LIST_NULL ret; 351 352fetch_new_scb: 353 bmov SCBHADDR, NEXT_QUEUED_SCB_ADDR, 4; 354 mvi CCARREN|CCSCBEN|CCSCBDIR|CCSCBRESET jmp dma_scb; 355dma_complete_scb: 356 bmov SCBPTR, COMPLETE_DMA_SCB_HEAD, 2; 357 bmov SCBHADDR, SCB_BUSADDR, 4; 358 mvi CCARREN|CCSCBEN|CCSCBRESET jmp dma_scb; 359END_CRITICAL; 360 361/* 362 * Either post or fetch an SCB from host memory. The caller 363 * is responsible for polling for transfer completion. 364 * 365 * Prerequisits: Mode == M_CCHAN 366 * SINDEX contains CCSCBCTL flags 367 * SCBHADDR set to Host SCB address 368 * SCBPTR set to SCB src location on "push" operations 369 */ 370SET_SRC_MODE M_CCHAN; 371SET_DST_MODE M_CCHAN; 372dma_scb: 373 mvi SCBHCNT, SCB_TRANSFER_SIZE; 374 mov CCSCBCTL, SINDEX ret; 375 376BEGIN_CRITICAL; 377setjmp: 378 bmov LONGJMP_ADDR, STACK, 2 ret; 379setjmp_inline: 380 bmov LONGJMP_ADDR, STACK, 2; 381longjmp: 382 bmov STACK, LONGJMP_ADDR, 2 ret; 383END_CRITICAL; 384 385/*************************** Chip Bug Work Arounds ****************************/ 386/* 387 * Must disable interrupts when setting the mode pointer 388 * register as an interrupt occurring mid update will 389 * fail to store the new mode value for restoration on 390 * an iret. 391 */ 392if ((ahd->bugs & AHD_SET_MODE_BUG) != 0) { 393set_mode_work_around: 394 mvi SEQINTCTL, INTVEC1DSL; 395 mov MODE_PTR, SINDEX; 396 clr SEQINTCTL ret; 397 398toggle_dff_mode_work_around: 399 mvi SEQINTCTL, INTVEC1DSL; 400 xor MODE_PTR, MK_MODE(M_DFF1, M_DFF1); 401 clr SEQINTCTL ret; 402} 403 404 405if ((ahd->bugs & AHD_INTCOLLISION_BUG) != 0) { 406set_seqint_work_around: 407 mov SEQINTCODE, SINDEX; 408 mvi SEQINTCODE, NO_SEQINT ret; 409} 410 411/************************ Packetized LongJmp Routines *************************/ 412SET_SRC_MODE M_SCSI; 413SET_DST_MODE M_SCSI; 414start_selection: 415BEGIN_CRITICAL; 416 if ((ahd->bugs & AHD_SENT_SCB_UPDATE_BUG) != 0) { 417 /* 418 * Razor #494 419 * Rev A hardware fails to update LAST/CURR/NEXTSCB 420 * correctly after a packetized selection in several 421 * situations: 422 * 423 * 1) If only one command existed in the queue, the 424 * LAST/CURR/NEXTSCB are unchanged. 425 * 426 * 2) In a non QAS, protocol allowed phase change, 427 * the queue is shifted 1 too far. LASTSCB is 428 * the last SCB that was correctly processed. 429 * 430 * 3) In the QAS case, if the full list of commands 431 * was successfully sent, NEXTSCB is NULL and neither 432 * CURRSCB nor LASTSCB can be trusted. We must 433 * manually walk the list counting MAXCMDCNT elements 434 * to find the last SCB that was sent correctly. 435 * 436 * To simplify the workaround for this bug in SELDO 437 * handling, we initialize LASTSCB prior to enabling 438 * selection so we can rely on it even for case #1 above. 439 */ 440 bmov LASTSCB, WAITING_TID_HEAD, 2; 441 } 442 bmov CURRSCB, WAITING_TID_HEAD, 2; 443 bmov SCBPTR, WAITING_TID_HEAD, 2; 444 shr SELOID, 4, SCB_SCSIID; 445 /* 446 * If we want to send a message to the device, ensure 447 * we are selecting with atn irregardless of our packetized 448 * agreement. Since SPI4 only allows target reset or PPR 449 * messages if this is a packetized connection, the change 450 * to our negotiation table entry for this selection will 451 * be cleared when the message is acted on. 452 */ 453 test SCB_CONTROL, MK_MESSAGE jz . + 3; 454 mov NEGOADDR, SELOID; 455 or NEGCONOPTS, ENAUTOATNO; 456 or SCSISEQ0, ENSELO ret; 457END_CRITICAL; 458 459/* 460 * Allocate a FIFO for a non-packetized transaction. 461 * In RevA hardware, both FIFOs must be free before we 462 * can allocate a FIFO for a non-packetized transaction. 463 */ 464allocate_fifo_loop: 465 /* 466 * Do whatever work is required to free a FIFO. 467 */ 468 call idle_loop_service_fifos; 469 SET_MODE(M_SCSI, M_SCSI) 470allocate_fifo: 471 if ((ahd->bugs & AHD_NONPACKFIFO_BUG) != 0) { 472 and A, FIFO0FREE|FIFO1FREE, DFFSTAT; 473 cmp A, FIFO0FREE|FIFO1FREE jne allocate_fifo_loop; 474 } else { 475 test DFFSTAT, FIFO1FREE jnz allocate_fifo1; 476 test DFFSTAT, FIFO0FREE jz allocate_fifo_loop; 477 mvi DFFSTAT, B_CURRFIFO_0; 478 SET_MODE(M_DFF0, M_DFF0) 479 bmov SCBPTR, ALLOCFIFO_SCBPTR, 2 ret; 480 } 481SET_SRC_MODE M_SCSI; 482SET_DST_MODE M_SCSI; 483allocate_fifo1: 484 mvi DFFSTAT, CURRFIFO_1; 485 SET_MODE(M_DFF1, M_DFF1) 486 bmov SCBPTR, ALLOCFIFO_SCBPTR, 2 ret; 487 488/* 489 * We have been reselected as an initiator 490 * or selected as a target. 491 */ 492SET_SRC_MODE M_SCSI; 493SET_DST_MODE M_SCSI; 494select_in: 495 if ((ahd->bugs & AHD_BUSFREEREV_BUG) != 0) { 496 /* 497 * This exposes a window whereby a 498 * busfree just after a selection will 499 * be missed, but there is no other safe 500 * way to enable busfree detection if 501 * the busfreerev function is broken. 502 */ 503 mvi CLRSINT1,CLRBUSFREE; 504 or SIMODE1, ENBUSFREE; 505 } 506 or SXFRCTL0, SPIOEN; 507 and SAVED_SCSIID, SELID_MASK, SELID; 508 and A, OID, IOWNID; 509 or SAVED_SCSIID, A; 510 mvi CLRSINT0, CLRSELDI; 511 jmp ITloop; 512 513/* 514 * We have successfully selected out. 515 * 516 * Clear SELDO. 517 * Dequeue all SCBs sent from the waiting queue 518 * Requeue all SCBs *not* sent to the tail of the waiting queue 519 * Take Razor #494 into account for above. 520 * 521 * In Packetized Mode: 522 * Return to the idle loop. Our interrupt handler will take 523 * care of any incoming L_Qs. 524 * 525 * In Non-Packetize Mode: 526 * Continue to our normal state machine. 527 */ 528SET_SRC_MODE M_SCSI; 529SET_DST_MODE M_SCSI; 530select_out: 531BEGIN_CRITICAL; 532 /* Clear out all SCBs that have been successfully sent. */ 533 if ((ahd->bugs & AHD_SENT_SCB_UPDATE_BUG) != 0) { 534 /* 535 * For packetized, the LQO manager clears ENSELO on 536 * the assertion of SELDO. If we are non-packetized, 537 * LASTSCB and CURRSCB are accurate. 538 */ 539 test SCSISEQ0, ENSELO jnz use_lastscb; 540 541 /* 542 * The update is correct for LQOSTAT1 errors. All 543 * but LQOBUSFREE are handled by kernel interrupts. 544 * If we see LQOBUSFREE, return to the idle loop. 545 * Once we are out of the select_out critical section, 546 * the kernel will cleanup the LQOBUSFREE and we will 547 * eventually restart the selection if appropriate. 548 */ 549 test LQOSTAT1, LQOBUSFREE jnz idle_loop; 550 551 /* 552 * On a phase change oustside of packet boundaries, 553 * LASTSCB points to the currently active SCB context 554 * on the bus. 555 */ 556 test LQOSTAT2, LQOPHACHGOUTPKT jnz use_lastscb; 557 558 /* 559 * If the hardware has traversed the whole list, NEXTSCB 560 * will be NULL, CURRSCB and LASTSCB cannot be trusted, 561 * but MAXCMDCNT is accurate. If we stop part way through 562 * the list or only had one command to issue, NEXTSCB[1] is 563 * not NULL and LASTSCB is the last command to go out. 564 */ 565 cmp NEXTSCB[1], SCB_LIST_NULL jne use_lastscb; 566 567 /* 568 * Brute force walk. 569 */ 570 bmov SCBPTR, WAITING_TID_HEAD, 2; 571 mvi SEQINTCTL, INTVEC1DSL; 572 mvi MODE_PTR, MK_MODE(M_CFG, M_CFG); 573 mov A, MAXCMDCNT; 574 mvi MODE_PTR, MK_MODE(M_SCSI, M_SCSI); 575 clr SEQINTCTL; 576find_lastscb_loop: 577 dec A; 578 test A, 0xFF jz found_last_sent_scb; 579 bmov SCBPTR, SCB_NEXT, 2; 580 jmp find_lastscb_loop; 581use_lastscb: 582 bmov SCBPTR, LASTSCB, 2; 583found_last_sent_scb: 584 bmov CURRSCB, SCBPTR, 2; 585curscb_ww_done: 586 } else { 587 bmov SCBPTR, CURRSCB, 2; 588 } 589 590 /* 591 * Requeue any SCBs not sent, to the tail of the waiting Q. 592 */ 593 cmp SCB_NEXT[1], SCB_LIST_NULL je select_out_list_done; 594 595 /* 596 * We know that neither the per-TID list nor the list of 597 * TIDs is empty. Use this knowledge to our advantage. 598 */ 599 bmov REG0, SCB_NEXT, 2; 600 bmov SCBPTR, WAITING_TID_TAIL, 2; 601 bmov SCB_NEXT2, REG0, 2; 602 bmov WAITING_TID_TAIL, REG0, 2; 603 jmp select_out_inc_tid_q; 604 605select_out_list_done: 606 /* 607 * The whole list made it. Just clear our TID's tail pointer 608 * unless we were queued independently due to our need to 609 * send a message. 610 */ 611 test SCB_CONTROL, MK_MESSAGE jnz select_out_inc_tid_q; 612 shr DINDEX, 3, SCB_SCSIID; 613 or DINDEX, 1; /* Want only the second byte */ 614 mvi DINDEX[1], ((WAITING_SCB_TAILS) >> 8); 615 mvi DINDIR, SCB_LIST_NULL; 616select_out_inc_tid_q: 617 bmov SCBPTR, WAITING_TID_HEAD, 2; 618 bmov WAITING_TID_HEAD, SCB_NEXT2, 2; 619 cmp WAITING_TID_HEAD[1], SCB_LIST_NULL jne . + 2; 620 mvi WAITING_TID_TAIL[1], SCB_LIST_NULL; 621 bmov SCBPTR, CURRSCB, 2; 622 mvi CLRSINT0, CLRSELDO; 623 test LQOSTAT2, LQOPHACHGOUTPKT jnz unexpected_nonpkt_phase; 624 test LQOSTAT1, LQOPHACHGINPKT jnz unexpected_nonpkt_phase; 625 626 /* 627 * If this is a packetized connection, return to our 628 * idle_loop and let our interrupt handler deal with 629 * any connection setup/teardown issues. The only 630 * exceptions are the case of MK_MESSAGE and task management 631 * SCBs. 632 */ 633 if ((ahd->bugs & AHD_LQO_ATNO_BUG) != 0) { 634 /* 635 * In the A, the LQO manager transitions to LQOSTOP0 even if 636 * we have selected out with ATN asserted and the target 637 * REQs in a non-packet phase. 638 */ 639 test SCB_CONTROL, MK_MESSAGE jz select_out_no_message; 640 test SCSISIGO, ATNO jnz select_out_non_packetized; 641select_out_no_message: 642 } 643 test LQOSTAT2, LQOSTOP0 jz select_out_non_packetized; 644 test SCB_TASK_MANAGEMENT, 0xFF jz idle_loop; 645 SET_SEQINTCODE(TASKMGMT_FUNC_COMPLETE) 646 jmp idle_loop; 647 648select_out_non_packetized: 649 /* Non packetized request. */ 650 and SCSISEQ0, ~ENSELO; 651 if ((ahd->bugs & AHD_BUSFREEREV_BUG) != 0) { 652 /* 653 * This exposes a window whereby a 654 * busfree just after a selection will 655 * be missed, but there is no other safe 656 * way to enable busfree detection if 657 * the busfreerev function is broken. 658 */ 659 mvi CLRSINT1,CLRBUSFREE; 660 or SIMODE1, ENBUSFREE; 661 } 662 mov SAVED_SCSIID, SCB_SCSIID; 663 mov SAVED_LUN, SCB_LUN; 664 mvi SEQ_FLAGS, NO_CDB_SENT; 665END_CRITICAL; 666 or SXFRCTL0, SPIOEN; 667 668 /* 669 * As soon as we get a successful selection, the target 670 * should go into the message out phase since we have ATN 671 * asserted. 672 */ 673 mvi MSG_OUT, MSG_IDENTIFYFLAG; 674 675 /* 676 * Main loop for information transfer phases. Wait for the 677 * target to assert REQ before checking MSG, C/D and I/O for 678 * the bus phase. 679 */ 680mesgin_phasemis: 681ITloop: 682 call phase_lock; 683 684 mov A, LASTPHASE; 685 686 test A, ~P_DATAIN_DT jz p_data; 687 cmp A,P_COMMAND je p_command; 688 cmp A,P_MESGOUT je p_mesgout; 689 cmp A,P_STATUS je p_status; 690 cmp A,P_MESGIN je p_mesgin; 691 692 SET_SEQINTCODE(BAD_PHASE) 693 jmp ITloop; /* Try reading the bus again. */ 694 695/* 696 * Command phase. Set up the DMA registers and let 'er rip. 697 */ 698p_command: 699 test SEQ_FLAGS, NOT_IDENTIFIED jz p_command_okay; 700 SET_SEQINTCODE(PROTO_VIOLATION) 701p_command_okay: 702 test MODE_PTR, ~(MK_MODE(M_DFF1, M_DFF1)) 703 jnz p_command_allocate_fifo; 704 /* 705 * Command retry. Free our current FIFO and 706 * re-allocate a FIFO so transfer state is 707 * reset. 708 */ 709SET_SRC_MODE M_DFF1; 710SET_DST_MODE M_DFF1; 711 mvi DFFSXFRCTL, RSTCHN|CLRSHCNT; 712 SET_MODE(M_SCSI, M_SCSI) 713p_command_allocate_fifo: 714 bmov ALLOCFIFO_SCBPTR, SCBPTR, 2; 715 call allocate_fifo; 716SET_SRC_MODE M_DFF1; 717SET_DST_MODE M_DFF1; 718 add NONE, -17, SCB_CDB_LEN; 719 jnc p_command_embedded; 720p_command_from_host: 721 bmov HADDR[0], SCB_HOST_CDB_PTR, 9; 722 mvi SG_CACHE_PRE, LAST_SEG; 723 mvi DFCNTRL, (PRELOADEN|SCSIEN|HDMAEN); 724 jmp p_command_xfer; 725p_command_embedded: 726 bmov SHCNT[0], SCB_CDB_LEN, 1; 727 bmov DFDAT, SCB_CDB_STORE, 16; 728 mvi DFCNTRL, SCSIEN; 729p_command_xfer: 730 and SEQ_FLAGS, ~NO_CDB_SENT; 731 test DFCNTRL, SCSIEN jnz .; 732 /* 733 * DMA Channel automatically disabled. 734 * Don't allow a data phase if the command 735 * was not fully transferred. 736 */ 737 test SSTAT2, SDONE jnz ITloop; 738 or SEQ_FLAGS, NO_CDB_SENT; 739 jmp ITloop; 740 741 742/* 743 * Status phase. Wait for the data byte to appear, then read it 744 * and store it into the SCB. 745 */ 746SET_SRC_MODE M_SCSI; 747SET_DST_MODE M_SCSI; 748p_status: 749 test SEQ_FLAGS,NOT_IDENTIFIED jnz mesgin_proto_violation; 750p_status_okay: 751 mov SCB_SCSI_STATUS, SCSIDAT; 752 or SCB_CONTROL, STATUS_RCVD; 753 jmp ITloop; 754 755/* 756 * Message out phase. If MSG_OUT is MSG_IDENTIFYFLAG, build a full 757 * indentify message sequence and send it to the target. The host may 758 * override this behavior by setting the MK_MESSAGE bit in the SCB 759 * control byte. This will cause us to interrupt the host and allow 760 * it to handle the message phase completely on its own. If the bit 761 * associated with this target is set, we will also interrupt the host, 762 * thereby allowing it to send a message on the next selection regardless 763 * of the transaction being sent. 764 * 765 * If MSG_OUT is == HOST_MSG, also interrupt the host and take a message. 766 * This is done to allow the host to send messages outside of an identify 767 * sequence while protecting the seqencer from testing the MK_MESSAGE bit 768 * on an SCB that might not be for the current nexus. (For example, a 769 * BDR message in responce to a bad reselection would leave us pointed to 770 * an SCB that doesn't have anything to do with the current target). 771 * 772 * Otherwise, treat MSG_OUT as a 1 byte message to send (abort, abort tag, 773 * bus device reset). 774 * 775 * When there are no messages to send, MSG_OUT should be set to MSG_NOOP, 776 * in case the target decides to put us in this phase for some strange 777 * reason. 778 */ 779p_mesgout_retry: 780 /* Turn on ATN for the retry */ 781 mvi SCSISIGO, ATNO; 782p_mesgout: 783 mov SINDEX, MSG_OUT; 784 cmp SINDEX, MSG_IDENTIFYFLAG jne p_mesgout_from_host; 785 test SCB_CONTROL,MK_MESSAGE jnz host_message_loop; 786p_mesgout_identify: 787 or SINDEX, MSG_IDENTIFYFLAG|DISCENB, SCB_LUN; 788 test SCB_CONTROL, DISCENB jnz . + 2; 789 and SINDEX, ~DISCENB; 790/* 791 * Send a tag message if TAG_ENB is set in the SCB control block. 792 * Use SCB_NONPACKET_TAG as the tag value. 793 */ 794p_mesgout_tag: 795 test SCB_CONTROL,TAG_ENB jz p_mesgout_onebyte; 796 mov SCSIDAT, SINDEX; /* Send the identify message */ 797 call phase_lock; 798 cmp LASTPHASE, P_MESGOUT jne p_mesgout_done; 799 and SCSIDAT,TAG_ENB|SCB_TAG_TYPE,SCB_CONTROL; 800 call phase_lock; 801 cmp LASTPHASE, P_MESGOUT jne p_mesgout_done; 802 mov SCBPTR jmp p_mesgout_onebyte; 803/* 804 * Interrupt the driver, and allow it to handle this message 805 * phase and any required retries. 806 */ 807p_mesgout_from_host: 808 cmp SINDEX, HOST_MSG jne p_mesgout_onebyte; 809 jmp host_message_loop; 810 811p_mesgout_onebyte: 812 mvi CLRSINT1, CLRATNO; 813 mov SCSIDAT, SINDEX; 814 815/* 816 * If the next bus phase after ATN drops is message out, it means 817 * that the target is requesting that the last message(s) be resent. 818 */ 819 call phase_lock; 820 cmp LASTPHASE, P_MESGOUT je p_mesgout_retry; 821 822p_mesgout_done: 823 mvi CLRSINT1,CLRATNO; /* Be sure to turn ATNO off */ 824 mov LAST_MSG, MSG_OUT; 825 mvi MSG_OUT, MSG_NOOP; /* No message left */ 826 jmp ITloop; 827 828/* 829 * Message in phase. Bytes are read using Automatic PIO mode. 830 */ 831p_mesgin: 832 /* read the 1st message byte */ 833 mvi ACCUM call inb_first; 834 835 test A,MSG_IDENTIFYFLAG jnz mesgin_identify; 836 cmp A,MSG_DISCONNECT je mesgin_disconnect; 837 cmp A,MSG_SAVEDATAPOINTER je mesgin_sdptrs; 838 cmp ALLZEROS,A je mesgin_complete; 839 cmp A,MSG_RESTOREPOINTERS je mesgin_rdptrs; 840 cmp A,MSG_IGN_WIDE_RESIDUE je mesgin_ign_wide_residue; 841 cmp A,MSG_NOOP je mesgin_done; 842 843/* 844 * Pushed message loop to allow the kernel to 845 * run it's own message state engine. To avoid an 846 * extra nop instruction after signaling the kernel, 847 * we perform the phase_lock before checking to see 848 * if we should exit the loop and skip the phase_lock 849 * in the ITloop. Performing back to back phase_locks 850 * shouldn't hurt, but why do it twice... 851 */ 852host_message_loop: 853 call phase_lock; /* Benign the first time through. */ 854 SET_SEQINTCODE(HOST_MSG_LOOP) 855 cmp RETURN_1, EXIT_MSG_LOOP je ITloop; 856 cmp RETURN_1, CONT_MSG_LOOP_WRITE jne . + 3; 857 mov SCSIDAT, RETURN_2; 858 jmp host_message_loop; 859 /* Must be CONT_MSG_LOOP_READ */ 860 mov NONE, SCSIDAT; /* ACK Byte */ 861 jmp host_message_loop; 862 863mesgin_ign_wide_residue: 864 mov SAVED_MODE, MODE_PTR; 865 SET_MODE(M_SCSI, M_SCSI) 866 shr NEGOADDR, 4, SAVED_SCSIID; 867 mov A, NEGCONOPTS; 868 RESTORE_MODE(SAVED_MODE) 869 test A, WIDEXFER jz mesgin_reject; 870 /* Pull the residue byte */ 871 mvi REG0 call inb_next; 872 cmp REG0, 0x01 jne mesgin_reject; 873 test SCB_RESIDUAL_SGPTR[0], SG_LIST_NULL jz . + 2; 874 test SCB_TASK_ATTRIBUTE, SCB_XFERLEN_ODD jnz mesgin_done; 875 SET_SEQINTCODE(IGN_WIDE_RES) 876 jmp mesgin_done; 877 878mesgin_proto_violation: 879 SET_SEQINTCODE(PROTO_VIOLATION) 880 jmp mesgin_done; 881mesgin_reject: 882 mvi MSG_MESSAGE_REJECT call mk_mesg; 883mesgin_done: 884 mov NONE,SCSIDAT; /*dummy read from latch to ACK*/ 885 jmp ITloop; 886 887#define INDEX_DISC_LIST(scsiid, lun) \ 888 and A, 0xC0, scsiid; \ 889 or SCBPTR, A, lun; \ 890 clr SCBPTR[1]; \ 891 and SINDEX, 0x30, scsiid; \ 892 shr SINDEX, 3; /* Multiply by 2 */ \ 893 add SINDEX, (SCB_DISCONNECTED_LISTS & 0xFF); \ 894 mvi SINDEX[1], ((SCB_DISCONNECTED_LISTS >> 8) & 0xFF) 895 896mesgin_identify: 897 /* 898 * Determine whether a target is using tagged or non-tagged 899 * transactions by first looking at the transaction stored in 900 * the per-device, disconnected array. If there is no untagged 901 * transaction for this target, this must be a tagged transaction. 902 */ 903 and SAVED_LUN, MSG_IDENTIFY_LUNMASK, A; 904 INDEX_DISC_LIST(SAVED_SCSIID, SAVED_LUN); 905 bmov DINDEX, SINDEX, 2; 906 bmov REG0, SINDIR, 2; 907 cmp REG0[1], SCB_LIST_NULL je snoop_tag; 908 /* Untagged. Clear the busy table entry and setup the SCB. */ 909 bmov DINDIR, ALLONES, 2; 910 bmov SCBPTR, REG0, 2; 911 jmp setup_SCB; 912 913/* 914 * Here we "snoop" the bus looking for a SIMPLE QUEUE TAG message. 915 * If we get one, we use the tag returned to find the proper 916 * SCB. After receiving the tag, look for the SCB at SCB locations tag and 917 * tag + 256. 918 */ 919snoop_tag: 920 if ((ahd->flags & AHD_SEQUENCER_DEBUG) != 0) { 921 or SEQ_FLAGS, 0x80; 922 } 923 mov NONE, SCSIDAT; /* ACK Identify MSG */ 924 call phase_lock; 925 if ((ahd->flags & AHD_SEQUENCER_DEBUG) != 0) { 926 or SEQ_FLAGS, 0x1; 927 } 928 cmp LASTPHASE, P_MESGIN jne not_found_ITloop; 929 if ((ahd->flags & AHD_SEQUENCER_DEBUG) != 0) { 930 or SEQ_FLAGS, 0x2; 931 } 932 cmp SCSIBUS, MSG_SIMPLE_Q_TAG jne not_found; 933get_tag: 934 clr SCBPTR[1]; 935 mvi SCBPTR call inb_next; /* tag value */ 936verify_scb: 937 test SCB_CONTROL,DISCONNECTED jz verify_other_scb; 938 mov A, SAVED_SCSIID; 939 cmp SCB_SCSIID, A jne verify_other_scb; 940 mov A, SAVED_LUN; 941 cmp SCB_LUN, A je setup_SCB_disconnected; 942verify_other_scb: 943 xor SCBPTR[1], 1; 944 test SCBPTR[1], 0xFF jnz verify_scb; 945 jmp not_found; 946 947/* 948 * Ensure that the SCB the tag points to is for 949 * an SCB transaction to the reconnecting target. 950 */ 951setup_SCB: 952 if ((ahd->flags & AHD_SEQUENCER_DEBUG) != 0) { 953 or SEQ_FLAGS, 0x10; 954 } 955 test SCB_CONTROL,DISCONNECTED jz not_found; 956setup_SCB_disconnected: 957 and SCB_CONTROL,~DISCONNECTED; 958 clr SEQ_FLAGS; /* make note of IDENTIFY */ 959 test SCB_SGPTR, SG_LIST_NULL jnz . + 3; 960 bmov ALLOCFIFO_SCBPTR, SCBPTR, 2; 961 call allocate_fifo; 962 /* See if the host wants to send a message upon reconnection */ 963 test SCB_CONTROL, MK_MESSAGE jz mesgin_done; 964 mvi HOST_MSG call mk_mesg; 965 jmp mesgin_done; 966 967not_found: 968 SET_SEQINTCODE(NO_MATCH) 969 jmp mesgin_done; 970 971not_found_ITloop: 972 SET_SEQINTCODE(NO_MATCH) 973 jmp ITloop; 974 975/* 976 * We received a "command complete" message. Put the SCB on the complete 977 * queue and trigger a completion interrupt via the idle loop. Before doing 978 * so, check to see if there 979 * is a residual or the status byte is something other than STATUS_GOOD (0). 980 * In either of these conditions, we upload the SCB back to the host so it can 981 * process this information. In the case of a non zero status byte, we 982 * additionally interrupt the kernel driver synchronously, allowing it to 983 * decide if sense should be retrieved. If the kernel driver wishes to request 984 * sense, it will fill the kernel SCB with a request sense command, requeue 985 * it to the QINFIFO and tell us not to post to the QOUTFIFO by setting 986 * RETURN_1 to SEND_SENSE. 987 */ 988mesgin_complete: 989 990 /* 991 * If ATN is raised, we still want to give the target a message. 992 * Perhaps there was a parity error on this last message byte. 993 * Either way, the target should take us to message out phase 994 * and then attempt to complete the command again. We should use a 995 * critical section here to guard against a timeout triggering 996 * for this command and setting ATN while we are still processing 997 * the completion. 998 test SCSISIGI, ATNI jnz mesgin_done; 999 */ 1000 1001 /* 1002 * If we are identified and have successfully sent the CDB, 1003 * any status will do. Optimize this fast path. 1004 */ 1005 test SCB_CONTROL, STATUS_RCVD jz mesgin_proto_violation; 1006 test SEQ_FLAGS, NOT_IDENTIFIED|NO_CDB_SENT jz complete_accepted; 1007 1008 /* 1009 * If the target never sent an identify message but instead went 1010 * to mesgin to give an invalid message, let the host abort us. 1011 */ 1012 test SEQ_FLAGS, NOT_IDENTIFIED jnz mesgin_proto_violation; 1013 1014 /* 1015 * If we recevied good status but never successfully sent the 1016 * cdb, abort the command. 1017 */ 1018 test SCB_SCSI_STATUS,0xff jnz complete_accepted; 1019 test SEQ_FLAGS, NO_CDB_SENT jnz mesgin_proto_violation; 1020complete_accepted: 1021 1022 /* 1023 * See if we attempted to deliver a message but the target ingnored us. 1024 */ 1025 test SCB_CONTROL, MK_MESSAGE jz complete_nomsg; 1026 SET_SEQINTCODE(MKMSG_FAILED) 1027complete_nomsg: 1028 call queue_scb_completion; 1029 jmp await_busfree; 1030 1031freeze_queue: 1032 /* Cancel any pending select-out. */ 1033 test SSTAT0, SELDO|SELINGO jnz . + 2; 1034 and SCSISEQ0, ~ENSELO; 1035 mov ACCUM_SAVE, A; 1036 clr A; 1037 add QFREEZE_COUNT, 1; 1038 adc QFREEZE_COUNT[1], A; 1039 or SEQ_FLAGS2, SELECTOUT_QFROZEN; 1040 mov A, ACCUM_SAVE ret; 1041 1042/* 1043 * Complete the current FIFO's SCB if data for this same 1044 * SCB is not transferring in the other FIFO. 1045 */ 1046SET_SRC_MODE M_DFF1; 1047SET_DST_MODE M_DFF1; 1048pkt_complete_scb_if_fifos_idle: 1049 bmov ARG_1, SCBPTR, 2; 1050 mvi DFFSXFRCTL, CLRCHN; 1051 SET_MODE(M_SCSI, M_SCSI) 1052 bmov SCBPTR, ARG_1, 2; 1053 test SCB_FIFO_USE_COUNT, 0xFF jnz return; 1054queue_scb_completion: 1055 test SCB_SCSI_STATUS,0xff jnz bad_status; 1056 /* 1057 * Check for residuals 1058 */ 1059 test SCB_SGPTR, SG_LIST_NULL jnz complete; /* No xfer */ 1060 test SCB_SGPTR, SG_FULL_RESID jnz upload_scb;/* Never xfered */ 1061 test SCB_RESIDUAL_SGPTR, SG_LIST_NULL jz upload_scb; 1062complete: 1063 bmov SCB_NEXT_COMPLETE, COMPLETE_SCB_HEAD, 2; 1064 bmov COMPLETE_SCB_HEAD, SCBPTR, 2 ret; 1065bad_status: 1066 cmp SCB_SCSI_STATUS, STATUS_PKT_SENSE je upload_scb; 1067 call freeze_queue; 1068upload_scb: 1069 /* 1070 * Restore SCB TAG since we reuse this field 1071 * in the sequencer. We don't want to corrupt 1072 * it on the host. 1073 */ 1074 bmov SCB_TAG, SCBPTR, 2; 1075 bmov SCB_NEXT_COMPLETE, COMPLETE_DMA_SCB_HEAD, 2; 1076 bmov COMPLETE_DMA_SCB_HEAD, SCBPTR, 2; 1077 or SCB_SGPTR, SG_STATUS_VALID ret; 1078 1079/* 1080 * Is it a disconnect message? Set a flag in the SCB to remind us 1081 * and await the bus going free. If this is an untagged transaction 1082 * store the SCB id for it in our untagged target table for lookup on 1083 * a reselction. 1084 */ 1085mesgin_disconnect: 1086 /* 1087 * If ATN is raised, we still want to give the target a message. 1088 * Perhaps there was a parity error on this last message byte 1089 * or we want to abort this command. Either way, the target 1090 * should take us to message out phase and then attempt to 1091 * disconnect again. 1092 * XXX - Wait for more testing. 1093 test SCSISIGI, ATNI jnz mesgin_done; 1094 */ 1095 test SEQ_FLAGS, NOT_IDENTIFIED|NO_CDB_SENT 1096 jnz mesgin_proto_violation; 1097 or SCB_CONTROL,DISCONNECTED; 1098 test SCB_CONTROL, TAG_ENB jnz await_busfree; 1099queue_disc_scb: 1100 bmov REG0, SCBPTR, 2; 1101 INDEX_DISC_LIST(SAVED_SCSIID, SAVED_LUN); 1102 bmov DINDEX, SINDEX, 2; 1103 bmov DINDIR, REG0, 2; 1104 bmov SCBPTR, REG0, 2; 1105 /* FALLTHROUGH */ 1106await_busfree: 1107 and SIMODE1, ~ENBUSFREE; 1108 if ((ahd->bugs & AHD_BUSFREEREV_BUG) == 0) { 1109 /* 1110 * In the BUSFREEREV_BUG case, the 1111 * busfree status was cleared at the 1112 * beginning of the connection. 1113 */ 1114 mvi CLRSINT1,CLRBUSFREE; 1115 } 1116 mov NONE, SCSIDAT; /* Ack the last byte */ 1117 test MODE_PTR, ~(MK_MODE(M_DFF1, M_DFF1)) 1118 jnz await_busfree_not_m_dff; 1119SET_SRC_MODE M_DFF1; 1120SET_DST_MODE M_DFF1; 1121await_busfree_clrchn: 1122 mvi DFFSXFRCTL, CLRCHN; 1123await_busfree_not_m_dff: 1124 call clear_target_state; 1125 test SSTAT1,REQINIT|BUSFREE jz .; 1126 test SSTAT1, BUSFREE jnz idle_loop; 1127 SET_SEQINTCODE(MISSED_BUSFREE) 1128 1129 1130/* 1131 * Save data pointers message: 1132 * Copying RAM values back to SCB, for Save Data Pointers message, but 1133 * only if we've actually been into a data phase to change them. This 1134 * protects against bogus data in scratch ram and the residual counts 1135 * since they are only initialized when we go into data_in or data_out. 1136 * Ack the message as soon as possible. 1137 */ 1138SET_SRC_MODE M_DFF1; 1139SET_DST_MODE M_DFF1; 1140mesgin_sdptrs: 1141 mov NONE,SCSIDAT; /*dummy read from latch to ACK*/ 1142 test SEQ_FLAGS, DPHASE jz ITloop; 1143 call save_pointers; 1144 jmp ITloop; 1145 1146save_pointers: 1147 /* 1148 * If we are asked to save our position at the end of the 1149 * transfer, just mark us at the end rather than perform a 1150 * full save. 1151 */ 1152 test SCB_RESIDUAL_SGPTR[0], SG_LIST_NULL jz save_pointers_full; 1153 or SCB_SGPTR, SG_LIST_NULL ret; 1154 1155save_pointers_full: 1156 /* 1157 * The SCB_DATAPTR becomes the current SHADDR. 1158 * All other information comes directly from our residual 1159 * state. 1160 */ 1161 bmov SCB_DATAPTR, SHADDR, 8; 1162 bmov SCB_DATACNT, SCB_RESIDUAL_DATACNT, 8 ret; 1163 1164/* 1165 * Restore pointers message? Data pointers are recopied from the 1166 * SCB anytime we enter a data phase for the first time, so all 1167 * we need to do is clear the DPHASE flag and let the data phase 1168 * code do the rest. We also reset/reallocate the FIFO to make 1169 * sure we have a clean start for the next data or command phase. 1170 */ 1171mesgin_rdptrs: 1172 and SEQ_FLAGS, ~DPHASE; 1173 test MODE_PTR, ~(MK_MODE(M_DFF1, M_DFF1)) jnz msgin_rdptrs_get_fifo; 1174 mvi DFFSXFRCTL, RSTCHN|CLRSHCNT; 1175 SET_MODE(M_SCSI, M_SCSI) 1176msgin_rdptrs_get_fifo: 1177 call allocate_fifo; 1178 jmp mesgin_done; 1179 1180clear_target_state: 1181 mvi LASTPHASE, P_BUSFREE; 1182 /* clear target specific flags */ 1183 mvi SEQ_FLAGS, NOT_IDENTIFIED|NO_CDB_SENT ret; 1184 1185phase_lock: 1186 if ((ahd->bugs & AHD_EARLY_REQ_BUG) != 0) { 1187 /* 1188 * Don't ignore persistent REQ assertions just because 1189 * they were asserted within the bus settle delay window. 1190 * This allows us to tolerate devices like the GEM318 1191 * that violate the SCSI spec. We are careful not to 1192 * count REQ while we are waiting for it to fall during 1193 * an async phase due to our asserted ACK. Each 1194 * sequencer instruction takes ~25ns, so the REQ must 1195 * last at least 100ns in order to be counted as a true 1196 * REQ. 1197 */ 1198 test SCSIPHASE, 0xFF jnz phase_locked; 1199 test SCSISIGI, ACKI jnz phase_lock; 1200 test SCSISIGI, REQI jz phase_lock; 1201 test SCSIPHASE, 0xFF jnz phase_locked; 1202 test SCSISIGI, ACKI jnz phase_lock; 1203 test SCSISIGI, REQI jz phase_lock; 1204phase_locked: 1205 } else { 1206 test SCSIPHASE, 0xFF jz .; 1207 } 1208 test SSTAT1, SCSIPERR jnz phase_lock; 1209phase_lock_latch_phase: 1210 and LASTPHASE, PHASE_MASK, SCSISIGI ret; 1211 1212/* 1213 * Functions to read data in Automatic PIO mode. 1214 * 1215 * An ACK is not sent on input from the target until SCSIDATL is read from. 1216 * So we wait until SCSIDATL is latched (the usual way), then read the data 1217 * byte directly off the bus using SCSIBUSL. When we have pulled the ATN 1218 * line, or we just want to acknowledge the byte, then we do a dummy read 1219 * from SCISDATL. The SCSI spec guarantees that the target will hold the 1220 * data byte on the bus until we send our ACK. 1221 * 1222 * The assumption here is that these are called in a particular sequence, 1223 * and that REQ is already set when inb_first is called. inb_{first,next} 1224 * use the same calling convention as inb. 1225 */ 1226inb_next: 1227 mov NONE,SCSIDAT; /*dummy read from latch to ACK*/ 1228inb_next_wait: 1229 /* 1230 * If there is a parity error, wait for the kernel to 1231 * see the interrupt and prepare our message response 1232 * before continuing. 1233 */ 1234 test SCSIPHASE, 0xFF jz .; 1235 test SSTAT1, SCSIPERR jnz inb_next_wait; 1236inb_next_check_phase: 1237 and LASTPHASE, PHASE_MASK, SCSISIGI; 1238 cmp LASTPHASE, P_MESGIN jne mesgin_phasemis; 1239inb_first: 1240 clr DINDEX[1]; 1241 mov DINDEX,SINDEX; 1242 mov DINDIR,SCSIBUS ret; /*read byte directly from bus*/ 1243inb_last: 1244 mov NONE,SCSIDAT ret; /*dummy read from latch to ACK*/ 1245 1246mk_mesg: 1247 mvi SCSISIGO, ATNO; 1248 mov MSG_OUT,SINDEX ret; 1249 1250SET_SRC_MODE M_DFF1; 1251SET_DST_MODE M_DFF1; 1252disable_ccsgen: 1253 test SG_STATE, FETCH_INPROG jz disable_ccsgen_fetch_done; 1254 clr CCSGCTL; 1255disable_ccsgen_fetch_done: 1256 clr SG_STATE ret; 1257 1258service_fifo: 1259 /* 1260 * Do we have any prefetch left??? 1261 */ 1262 test SG_STATE, SEGS_AVAIL jnz idle_sg_avail; 1263 1264 /* 1265 * Can this FIFO have access to the S/G cache yet? 1266 */ 1267 test CCSGCTL, SG_CACHE_AVAIL jz return; 1268 1269 /* Did we just finish fetching segs? */ 1270 test CCSGCTL, CCSGDONE jnz idle_sgfetch_complete; 1271 1272 /* Are we actively fetching segments? */ 1273 test CCSGCTL, CCSGENACK jnz return; 1274 1275 /* 1276 * We fetch a "cacheline aligned" and sized amount of data 1277 * so we don't end up referencing a non-existant page. 1278 * Cacheline aligned is in quotes because the kernel will 1279 * set the prefetch amount to a reasonable level if the 1280 * cacheline size is unknown. 1281 */ 1282 bmov SGHADDR, SCB_RESIDUAL_SGPTR, 4; 1283 mvi SGHCNT, SG_PREFETCH_CNT; 1284 if ((ahd->bugs & AHD_REG_SLOW_SETTLE_BUG) != 0) { 1285 /* 1286 * Need two instruction between "touches" of SGHADDR. 1287 */ 1288 nop; 1289 } 1290 and SGHADDR[0], SG_PREFETCH_ALIGN_MASK, SCB_RESIDUAL_SGPTR; 1291 mvi CCSGCTL, CCSGEN|CCSGRESET; 1292 or SG_STATE, FETCH_INPROG ret; 1293idle_sgfetch_complete: 1294 /* 1295 * Guard against SG_CACHE_AVAIL activating during sg fetch 1296 * request in the other FIFO. 1297 */ 1298 test SG_STATE, FETCH_INPROG jz return; 1299 clr CCSGCTL; 1300 and CCSGADDR, SG_PREFETCH_ADDR_MASK, SCB_RESIDUAL_SGPTR; 1301 mvi SG_STATE, SEGS_AVAIL|LOADING_NEEDED; 1302idle_sg_avail: 1303 /* Does the hardware have space for another SG entry? */ 1304 test DFSTATUS, PRELOAD_AVAIL jz return; 1305 /* 1306 * On the A, preloading a segment before HDMAENACK 1307 * comes true can clobber the shaddow address of the 1308 * first segment in the S/G FIFO. Wait until it is 1309 * safe to proceed. 1310 */ 1311 if ((ahd->features & AHD_NEW_DFCNTRL_OPTS) == 0) { 1312 test DFCNTRL, HDMAENACK jz return; 1313 } 1314 if ((ahd->flags & AHD_64BIT_ADDRESSING) != 0) { 1315 bmov HADDR, CCSGRAM, 8; 1316 } else { 1317 bmov HADDR, CCSGRAM, 4; 1318 } 1319 bmov HCNT, CCSGRAM, 3; 1320 bmov SCB_RESIDUAL_DATACNT[3], CCSGRAM, 1; 1321 if ((ahd->flags & AHD_39BIT_ADDRESSING) != 0) { 1322 and HADDR[4], SG_HIGH_ADDR_BITS, SCB_RESIDUAL_DATACNT[3]; 1323 } 1324 if ((ahd->flags & AHD_64BIT_ADDRESSING) != 0) { 1325 /* Skip 4 bytes of pad. */ 1326 add CCSGADDR, 4; 1327 } 1328sg_advance: 1329 clr A; /* add sizeof(struct scatter) */ 1330 add SCB_RESIDUAL_SGPTR[0],SG_SIZEOF; 1331 adc SCB_RESIDUAL_SGPTR[1],A; 1332 adc SCB_RESIDUAL_SGPTR[2],A; 1333 adc SCB_RESIDUAL_SGPTR[3],A; 1334 mov SINDEX, SCB_RESIDUAL_SGPTR[0]; 1335 test SCB_RESIDUAL_DATACNT[3], SG_LAST_SEG jz . + 3; 1336 or SINDEX, LAST_SEG; 1337 clr SG_STATE; 1338 mov SG_CACHE_PRE, SINDEX; 1339 if ((ahd->features & AHD_NEW_DFCNTRL_OPTS) != 0) { 1340 /* 1341 * Use SCSIENWRDIS so that SCSIEN is never 1342 * modified by this operation. 1343 */ 1344 or DFCNTRL, PRELOADEN|HDMAEN|SCSIENWRDIS; 1345 } else { 1346 or DFCNTRL, PRELOADEN|HDMAEN; 1347 } 1348 /* 1349 * Do we have another segment in the cache? 1350 */ 1351 add NONE, SG_PREFETCH_CNT_LIMIT, CCSGADDR; 1352 jnc return; 1353 and SG_STATE, ~SEGS_AVAIL ret; 1354 1355/* 1356 * Initialize the DMA address and counter from the SCB. 1357 */ 1358load_first_seg: 1359 bmov HADDR, SCB_DATAPTR, 11; 1360 and REG_ISR, ~SG_FULL_RESID, SCB_SGPTR[0]; 1361 test SCB_DATACNT[3], SG_LAST_SEG jz . + 2; 1362 or REG_ISR, LAST_SEG; 1363 mov SG_CACHE_PRE, REG_ISR; 1364 mvi DFCNTRL, (PRELOADEN|SCSIEN|HDMAEN); 1365 /* 1366 * Since we've are entering a data phase, we will 1367 * rely on the SCB_RESID* fields. Initialize the 1368 * residual and clear the full residual flag. 1369 */ 1370 and SCB_SGPTR[0], ~SG_FULL_RESID; 1371 bmov SCB_RESIDUAL_DATACNT[3], SCB_DATACNT[3], 5; 1372 /* If we need more S/G elements, tell the idle loop */ 1373 test SCB_RESIDUAL_DATACNT[3], SG_LAST_SEG jnz . + 2; 1374 mvi SG_STATE, LOADING_NEEDED ret; 1375 clr SG_STATE ret; 1376 1377p_data_handle_xfer: 1378 call setjmp; 1379 test SG_STATE, LOADING_NEEDED jnz service_fifo; 1380p_data_clear_handler: 1381 or LONGJMP_ADDR[1], INVALID_ADDR ret; 1382 1383p_data: 1384 test SEQ_FLAGS, NOT_IDENTIFIED|NO_CDB_SENT jz p_data_allowed; 1385 SET_SEQINTCODE(PROTO_VIOLATION) 1386p_data_allowed: 1387 1388 test SEQ_FLAGS, DPHASE jz data_phase_initialize; 1389 1390 /* 1391 * If we re-enter the data phase after going through another 1392 * phase, our transfer location has almost certainly been 1393 * corrupted by the interveining, non-data, transfers. Ask 1394 * the host driver to fix us up based on the transfer residual 1395 * unless we already know that we should be bitbucketing. 1396 */ 1397 test SCB_RESIDUAL_SGPTR[0], SG_LIST_NULL jnz p_data_bitbucket; 1398 SET_SEQINTCODE(PDATA_REINIT) 1399 jmp data_phase_inbounds; 1400 1401p_data_bitbucket: 1402 /* 1403 * Turn on `Bit Bucket' mode, wait until the target takes 1404 * us to another phase, and then notify the host. 1405 */ 1406 mov SAVED_MODE, MODE_PTR; 1407 test MODE_PTR, ~(MK_MODE(M_DFF1, M_DFF1)) 1408 jnz bitbucket_not_m_dff; 1409 /* 1410 * Ensure that any FIFO contents are cleared out and the 1411 * FIFO free'd prior to starting the BITBUCKET. BITBUCKET 1412 * doesn't discard data already in the FIFO. 1413 */ 1414 mvi DFFSXFRCTL, RSTCHN|CLRSHCNT; 1415 SET_MODE(M_SCSI, M_SCSI) 1416bitbucket_not_m_dff: 1417 or SXFRCTL1,BITBUCKET; 1418 /* Wait for non-data phase. */ 1419 test SCSIPHASE, ~DATA_PHASE_MASK jz .; 1420 and SXFRCTL1, ~BITBUCKET; 1421 RESTORE_MODE(SAVED_MODE) 1422SET_SRC_MODE M_DFF1; 1423SET_DST_MODE M_DFF1; 1424 SET_SEQINTCODE(DATA_OVERRUN) 1425 jmp ITloop; 1426 1427data_phase_initialize: 1428 test SCB_SGPTR[0], SG_LIST_NULL jnz p_data_bitbucket; 1429 call load_first_seg; 1430data_phase_inbounds: 1431 /* We have seen a data phase at least once. */ 1432 or SEQ_FLAGS, DPHASE; 1433 mov SAVED_MODE, MODE_PTR; 1434 test SG_STATE, LOADING_NEEDED jz data_group_dma_loop; 1435 call p_data_handle_xfer; 1436data_group_dma_loop: 1437 /* 1438 * The transfer is complete if either the last segment 1439 * completes or the target changes phase. Both conditions 1440 * will clear SCSIEN. 1441 */ 1442 call idle_loop_service_fifos; 1443 call idle_loop_cchan; 1444 call idle_loop_gsfifo; 1445 RESTORE_MODE(SAVED_MODE) 1446 test DFCNTRL, SCSIEN jnz data_group_dma_loop; 1447 1448data_group_dmafinish: 1449 /* 1450 * The transfer has terminated either due to a phase 1451 * change, and/or the completion of the last segment. 1452 * We have two goals here. Do as much other work 1453 * as possible while the data fifo drains on a read 1454 * and respond as quickly as possible to the standard 1455 * messages (save data pointers/disconnect and command 1456 * complete) that usually follow a data phase. 1457 */ 1458 call calc_residual; 1459 1460 /* 1461 * Go ahead and shut down the DMA engine now. 1462 */ 1463 test DFCNTRL, DIRECTION jnz data_phase_finish; 1464data_group_fifoflush: 1465 if ((ahd->bugs & AHD_AUTOFLUSH_BUG) != 0) { 1466 or DFCNTRL, FIFOFLUSH; 1467 } 1468 /* 1469 * We have enabled the auto-ack feature. This means 1470 * that the controller may have already transferred 1471 * some overrun bytes into the data FIFO and acked them 1472 * on the bus. The only way to detect this situation is 1473 * to wait for LAST_SEG_DONE to come true on a completed 1474 * transfer and then test to see if the data FIFO is 1475 * non-empty. We know there is more data yet to transfer 1476 * if SG_LIST_NULL is not yet set, thus there cannot be 1477 * an overrun. 1478 */ 1479 test SCB_RESIDUAL_SGPTR[0], SG_LIST_NULL jz data_phase_finish; 1480 test SG_CACHE_SHADOW, LAST_SEG_DONE jz .; 1481 test DFSTATUS, FIFOEMP jnz data_phase_finish; 1482 /* Overrun */ 1483 jmp p_data; 1484data_phase_finish: 1485 /* 1486 * If the target has left us in data phase, loop through 1487 * the DMA code again. We will only loop if there is a 1488 * data overrun. 1489 */ 1490 if ((ahd->flags & AHD_TARGETROLE) != 0) { 1491 test SSTAT0, TARGET jnz data_phase_done; 1492 } 1493 if ((ahd->flags & AHD_INITIATORROLE) != 0) { 1494 test SSTAT1, REQINIT jz .; 1495 test SCSIPHASE, DATA_PHASE_MASK jnz p_data; 1496 } 1497 1498data_phase_done: 1499 /* Kill off any pending prefetch */ 1500 call disable_ccsgen; 1501 or LONGJMP_ADDR[1], INVALID_ADDR; 1502 1503 if ((ahd->flags & AHD_TARGETROLE) != 0) { 1504 test SEQ_FLAGS, DPHASE_PENDING jz ITloop; 1505 /* 1506 and SEQ_FLAGS, ~DPHASE_PENDING; 1507 * For data-in phases, wait for any pending acks from the 1508 * initiator before changing phase. We only need to 1509 * send Ignore Wide Residue messages for data-in phases. 1510 test DFCNTRL, DIRECTION jz target_ITloop; 1511 test SSTAT1, REQINIT jnz .; 1512 test SCB_TASK_ATTRIBUTE, SCB_XFERLEN_ODD jz target_ITloop; 1513 SET_MODE(M_SCSI, M_SCSI) 1514 test NEGCONOPTS, WIDEXFER jz target_ITloop; 1515 */ 1516 /* 1517 * Issue an Ignore Wide Residue Message. 1518 mvi P_MESGIN|BSYO call change_phase; 1519 mvi MSG_IGN_WIDE_RESIDUE call target_outb; 1520 mvi 1 call target_outb; 1521 jmp target_ITloop; 1522 */ 1523 } else { 1524 jmp ITloop; 1525 } 1526 1527/* 1528 * We assume that, even though data may still be 1529 * transferring to the host, that the SCSI side of 1530 * the DMA engine is now in a static state. This 1531 * allows us to update our notion of where we are 1532 * in this transfer. 1533 * 1534 * If, by chance, we stopped before being able 1535 * to fetch additional segments for this transfer, 1536 * yet the last S/G was completely exhausted, 1537 * call our idle loop until it is able to load 1538 * another segment. This will allow us to immediately 1539 * pickup on the next segment on the next data phase. 1540 * 1541 * If we happened to stop on the last segment, then 1542 * our residual information is still correct from 1543 * the idle loop and there is no need to perform 1544 * any fixups. 1545 */ 1546residual_before_last_seg: 1547 test MDFFSTAT, SHVALID jnz sgptr_fixup; 1548 /* 1549 * Can never happen from an interrupt as the packetized 1550 * hardware will only interrupt us once SHVALID or 1551 * LAST_SEG_DONE. 1552 */ 1553 call idle_loop_service_fifos; 1554 RESTORE_MODE(SAVED_MODE) 1555 /* FALLTHROUGH */ 1556calc_residual: 1557 test SG_CACHE_SHADOW, LAST_SEG jz residual_before_last_seg; 1558 /* Record if we've consumed all S/G entries */ 1559 test MDFFSTAT, SHVALID jz . + 2; 1560 bmov SCB_RESIDUAL_DATACNT, SHCNT, 3 ret; 1561 or SCB_RESIDUAL_SGPTR[0], SG_LIST_NULL ret; 1562 1563sgptr_fixup: 1564 /* 1565 * Fixup the residual next S/G pointer. The S/G preload 1566 * feature of the chip allows us to load two elements 1567 * in addition to the currently active element. We 1568 * store the bottom byte of the next S/G pointer in 1569 * the SG_CACHE_PTR register so we can restore the 1570 * correct value when the DMA completes. If the next 1571 * sg ptr value has advanced to the point where higher 1572 * bytes in the address have been affected, fix them 1573 * too. 1574 */ 1575 test SG_CACHE_SHADOW, 0x80 jz sgptr_fixup_done; 1576 test SCB_RESIDUAL_SGPTR[0], 0x80 jnz sgptr_fixup_done; 1577 add SCB_RESIDUAL_SGPTR[1], -1; 1578 adc SCB_RESIDUAL_SGPTR[2], -1; 1579 adc SCB_RESIDUAL_SGPTR[3], -1; 1580sgptr_fixup_done: 1581 and SCB_RESIDUAL_SGPTR[0], SG_ADDR_MASK, SG_CACHE_SHADOW; 1582 clr SCB_RESIDUAL_DATACNT[3]; /* We are not the last seg */ 1583 bmov SCB_RESIDUAL_DATACNT, SHCNT, 3 ret; 1584 1585export timer_isr: 1586 call issue_cmdcmplt; 1587 mvi CLRSEQINTSTAT, CLRSEQ_SWTMRTO; 1588 if ((ahd->bugs & AHD_SET_MODE_BUG) != 0) { 1589 /* 1590 * In H2A4, the mode pointer is not saved 1591 * for intvec2, but is restored on iret. 1592 * This can lead to the restoration of a 1593 * bogus mode ptr. Manually clear the 1594 * intmask bits and do a normal return 1595 * to compensate. 1596 */ 1597 and SEQINTCTL, ~(INTMASK2|INTMASK1) ret; 1598 } else { 1599 or SEQINTCTL, IRET ret; 1600 } 1601 1602export seq_isr: 1603 if ((ahd->features & AHD_RTI) == 0) { 1604 /* 1605 * On RevA Silicon, if the target returns us to data-out 1606 * after we have already trained for data-out, it is 1607 * possible for us to transition the free running clock to 1608 * data-valid before the required 100ns P1 setup time (8 P1 1609 * assertions in fast-160 mode). This will only happen if 1610 * this L-Q is a continuation of a data transfer for which 1611 * we have already prefetched data into our FIFO (LQ/Data 1612 * followed by LQ/Data for the same write transaction). 1613 * This can cause some target implementations to miss the 1614 * first few data transfers on the bus. We detect this 1615 * situation by noticing that this is the first data transfer 1616 * after an LQ (LQIWORKONLQ true), that the data transfer is 1617 * a continuation of a transfer already setup in our FIFO 1618 * (SAVEPTRS interrupt), and that the transaction is a write 1619 * (DIRECTION set in DFCNTRL). The delay is performed by 1620 * disabling SCSIEN until we see the first REQ from the 1621 * target. 1622 * 1623 * First instruction in an ISR cannot be a branch on 1624 * Rev A. Snapshot LQISTAT2 so the status is not missed 1625 * and deffer the test by one instruction. 1626 */ 1627 mov REG_ISR, LQISTAT2; 1628 test REG_ISR, LQIWORKONLQ jz main_isr; 1629 test SEQINTSRC, SAVEPTRS jz main_isr; 1630 test LONGJMP_ADDR[1], INVALID_ADDR jz saveptr_active_fifo; 1631 /* 1632 * Switch to the active FIFO after clearing the snapshot 1633 * savepointer in the current FIFO. We do this so that 1634 * a pending CTXTDONE or SAVEPTR is visible in the active 1635 * FIFO. This status is the only way we can detect if we 1636 * have lost the race (e.g. host paused us) and our attepts 1637 * to disable the channel occurred after all REQs were 1638 * already seen and acked (REQINIT never comes true). 1639 */ 1640 mvi DFFSXFRCTL, CLRCHN; 1641 xor MODE_PTR, MK_MODE(M_DFF1, M_DFF1); 1642 test DFCNTRL, DIRECTION jz interrupt_return; 1643 and DFCNTRL, ~SCSIEN; 1644snapshot_wait_data_valid: 1645 test SEQINTSRC, (CTXTDONE|SAVEPTRS) jnz snapshot_data_valid; 1646 test SSTAT1, REQINIT jz snapshot_wait_data_valid; 1647snapshot_data_valid: 1648 or DFCNTRL, SCSIEN; 1649 or SEQINTCTL, IRET ret; 1650snapshot_saveptr: 1651 mvi DFFSXFRCTL, CLRCHN; 1652 or SEQINTCTL, IRET ret; 1653main_isr: 1654 } 1655 test SEQINTSRC, CFG4DATA jnz cfg4data_intr; 1656 test SEQINTSRC, CFG4ISTAT jnz cfg4istat_intr; 1657 test SEQINTSRC, SAVEPTRS jnz saveptr_intr; 1658 test SEQINTSRC, CFG4ICMD jnz cfg4icmd_intr; 1659 SET_SEQINTCODE(INVALID_SEQINT) 1660 1661/* 1662 * There are two types of save pointers interrupts: 1663 * The first is a snapshot save pointers where the current FIFO is not 1664 * active and contains a snapshot of the current poniter information. 1665 * This happens between packets in a stream for a single L_Q. Since we 1666 * are not performing a pointer save, we can safely clear the channel 1667 * so it can be used for other transactions. On RTI capable controllers, 1668 * where snapshots can, and are, disabled, the code to handle this type 1669 * of snapshot is not active. 1670 * 1671 * The second case is a save pointers on an active FIFO which occurs 1672 * if the target changes to a new L_Q or busfrees/QASes and the transfer 1673 * has a residual. This should occur coincident with a ctxtdone. We 1674 * disable the interrupt and allow our active routine to handle the 1675 * save. 1676 */ 1677saveptr_intr: 1678 if ((ahd->features & AHD_RTI) == 0) { 1679 test LONGJMP_ADDR[1], INVALID_ADDR jnz snapshot_saveptr; 1680 } 1681saveptr_active_fifo: 1682 and SEQIMODE, ~ENSAVEPTRS; 1683 or SEQINTCTL, IRET ret; 1684 1685cfg4data_intr: 1686 test SCB_SGPTR[0], SG_LIST_NULL jnz pkt_handle_overrun_inc_use_count; 1687 call load_first_seg; 1688 call pkt_handle_xfer; 1689 inc SCB_FIFO_USE_COUNT; 1690interrupt_return: 1691 or SEQINTCTL, IRET ret; 1692 1693cfg4istat_intr: 1694 call freeze_queue; 1695 add NONE, -13, SCB_CDB_LEN; 1696 jnc cfg4istat_have_sense_addr; 1697 test SCB_CDB_LEN, SCB_CDB_LEN_PTR jnz cfg4istat_have_sense_addr; 1698 /* 1699 * Host sets up address/count and enables transfer. 1700 */ 1701 SET_SEQINTCODE(CFG4ISTAT_INTR) 1702 jmp cfg4istat_setup_handler; 1703cfg4istat_have_sense_addr: 1704 bmov HADDR, SCB_SENSE_BUSADDR, 4; 1705 mvi HCNT[1], (AHD_SENSE_BUFSIZE >> 8); 1706 mvi SG_CACHE_PRE, LAST_SEG; 1707 mvi DFCNTRL, PRELOADEN|SCSIEN|HDMAEN; 1708cfg4istat_setup_handler: 1709 /* 1710 * Status pkt is transferring to host. 1711 * Wait in idle loop for transfer to complete. 1712 * If a command completed before an attempted 1713 * task management function completed, notify the host. 1714 */ 1715 test SCB_TASK_MANAGEMENT, 0xFF jz cfg4istat_no_taskmgmt_func; 1716 SET_SEQINTCODE(TASKMGMT_CMD_CMPLT_OKAY) 1717cfg4istat_no_taskmgmt_func: 1718 call pkt_handle_status; 1719 or SEQINTCTL, IRET ret; 1720 1721cfg4icmd_intr: 1722 /* 1723 * In the case of DMAing a CDB from the host, the normal 1724 * CDB buffer is formatted with an 8 byte address followed 1725 * by a 1 byte count. 1726 */ 1727 bmov HADDR[0], SCB_HOST_CDB_PTR, 9; 1728 mvi SG_CACHE_PRE, LAST_SEG; 1729 mvi DFCNTRL, (PRELOADEN|SCSIEN|HDMAEN); 1730 call pkt_handle_cdb; 1731 or SEQINTCTL, IRET ret; 1732 1733/* 1734 * See if the target has gone on in this context creating an 1735 * overrun condition. For the write case, the hardware cannot 1736 * ack bytes until data are provided. So, if the target begins 1737 * another packet without changing contexts, implying we are 1738 * not sitting on a packet boundary, we are in an overrun 1739 * situation. For the read case, the hardware will continue to 1740 * ack bytes into the FIFO, and may even ack the last overrun packet 1741 * into the FIFO. If the FIFO should become non-empty, we are in 1742 * a read overrun case. 1743 */ 1744#define check_overrun \ 1745 /* Not on a packet boundary. */ \ 1746 test MDFFSTAT, DLZERO jz pkt_handle_overrun; \ 1747 test DFSTATUS, FIFOEMP jz pkt_handle_overrun 1748 1749pkt_handle_xfer: 1750 test SG_STATE, LOADING_NEEDED jz pkt_last_seg; 1751 call setjmp; 1752 test SEQINTSRC, SAVEPTRS jnz pkt_saveptrs; 1753 test SCSIPHASE, ~DATA_PHASE_MASK jz . + 2; 1754 test SCSISIGO, ATNO jnz . + 2; 1755 test SSTAT2, NONPACKREQ jz pkt_service_fifo; 1756 /* 1757 * Defer handling of this NONPACKREQ until we 1758 * can be sure it pertains to this FIFO. SAVEPTRS 1759 * will not be asserted if the NONPACKREQ is for us, 1760 * so we must simulate it if shaddow is valid. If 1761 * shaddow is not valid, keep running this FIFO until we 1762 * have satisfied the transfer by loading segments and 1763 * waiting for either shaddow valid or last_seg_done. 1764 */ 1765 test MDFFSTAT, SHVALID jnz pkt_saveptrs; 1766pkt_service_fifo: 1767 test SG_STATE, LOADING_NEEDED jnz service_fifo; 1768pkt_last_seg: 1769 call setjmp; 1770 test SEQINTSRC, SAVEPTRS jnz pkt_saveptrs; 1771 test SG_CACHE_SHADOW, LAST_SEG_DONE jnz pkt_last_seg_done; 1772 test SCSIPHASE, ~DATA_PHASE_MASK jz . + 2; 1773 test SCSISIGO, ATNO jnz . + 2; 1774 test SSTAT2, NONPACKREQ jz return; 1775 test MDFFSTAT, SHVALID jz return; 1776 /* FALLTHROUGH */ 1777 1778/* 1779 * Either a SAVEPTRS interrupt condition is pending for this FIFO 1780 * or we have a pending NONPACKREQ for this FIFO. We differentiate 1781 * between the two by capturing the state of the SAVEPTRS interrupt 1782 * prior to clearing this status and executing the common code for 1783 * these two cases. 1784 */ 1785pkt_saveptrs: 1786BEGIN_CRITICAL; 1787 if ((ahd->bugs & AHD_AUTOFLUSH_BUG) != 0) { 1788 or DFCNTRL, FIFOFLUSH; 1789 } 1790 mov REG0, SEQINTSRC; 1791 call calc_residual; 1792 call save_pointers; 1793 mvi CLRSEQINTSRC, CLRSAVEPTRS; 1794 call disable_ccsgen; 1795 or SEQIMODE, ENSAVEPTRS; 1796 test DFCNTRL, DIRECTION jnz pkt_saveptrs_check_status; 1797 test DFSTATUS, FIFOEMP jnz pkt_saveptrs_check_status; 1798 /* 1799 * Keep a handler around for this FIFO until it drains 1800 * to the host to guarantee that we don't complete the 1801 * command to the host before the data arrives. 1802 */ 1803pkt_saveptrs_wait_fifoemp: 1804 call setjmp; 1805 test DFSTATUS, FIFOEMP jz return; 1806pkt_saveptrs_check_status: 1807 or LONGJMP_ADDR[1], INVALID_ADDR; 1808 test REG0, SAVEPTRS jz unexpected_nonpkt_phase; 1809 dec SCB_FIFO_USE_COUNT; 1810 test SCB_CONTROL, STATUS_RCVD jnz pkt_complete_scb_if_fifos_idle; 1811 mvi DFFSXFRCTL, CLRCHN ret; 1812END_CRITICAL; 1813 1814/* 1815 * LAST_SEG_DONE status has been seen in the current FIFO. 1816 * This indicates that all of the allowed data for this 1817 * command has transferred across the SCSI and host buses. 1818 * Check for overrun and see if we can complete this command. 1819 */ 1820pkt_last_seg_done: 1821BEGIN_CRITICAL; 1822 /* 1823 * Mark transfer as completed. 1824 */ 1825 or SCB_SGPTR, SG_LIST_NULL; 1826 1827 /* 1828 * Wait for the current context to finish to verify that 1829 * no overrun condition has occurred. 1830 */ 1831 test SEQINTSRC, CTXTDONE jnz pkt_ctxt_done; 1832 call setjmp; 1833pkt_wait_ctxt_done_loop: 1834 test SEQINTSRC, CTXTDONE jnz pkt_ctxt_done; 1835 /* 1836 * A sufficiently large overrun or a NONPACKREQ may 1837 * prevent CTXTDONE from ever asserting, so we must 1838 * poll for these statuses too. 1839 */ 1840 check_overrun; 1841 test SSTAT2, NONPACKREQ jz return; 1842 test SEQINTSRC, CTXTDONE jz unexpected_nonpkt_phase; 1843 /* FALLTHROUGH */ 1844 1845pkt_ctxt_done: 1846 check_overrun; 1847 or LONGJMP_ADDR[1], INVALID_ADDR; 1848 /* 1849 * If status has been received, it is safe to skip 1850 * the check to see if another FIFO is active because 1851 * LAST_SEG_DONE has been observed. However, we check 1852 * the FIFO anyway since it costs us only one extra 1853 * instruction to leverage common code to perform the 1854 * SCB completion. 1855 */ 1856 dec SCB_FIFO_USE_COUNT; 1857 test SCB_CONTROL, STATUS_RCVD jnz pkt_complete_scb_if_fifos_idle; 1858 mvi DFFSXFRCTL, CLRCHN ret; 1859END_CRITICAL; 1860 1861/* 1862 * Must wait until CDB xfer is over before issuing the 1863 * clear channel. 1864 */ 1865pkt_handle_cdb: 1866 call setjmp; 1867 test SG_CACHE_SHADOW, LAST_SEG_DONE jz return; 1868 or LONGJMP_ADDR[1], INVALID_ADDR; 1869 mvi DFFSXFRCTL, CLRCHN ret; 1870 1871/* 1872 * Watch over the status transfer. Our host sense buffer is 1873 * large enough to take the maximum allowed status packet. 1874 * None-the-less, we must still catch and report overruns to 1875 * the host. Additionally, properly catch unexpected non-packet 1876 * phases that are typically caused by CRC errors in status packet 1877 * transmission. 1878 */ 1879pkt_handle_status: 1880 call setjmp; 1881 test SG_CACHE_SHADOW, LAST_SEG_DONE jnz pkt_status_check_overrun; 1882 test SEQINTSRC, CTXTDONE jz pkt_status_check_nonpackreq; 1883 test SG_CACHE_SHADOW, LAST_SEG_DONE jnz pkt_status_check_overrun; 1884pkt_status_IU_done: 1885 if ((ahd->bugs & AHD_AUTOFLUSH_BUG) != 0) { 1886 or DFCNTRL, FIFOFLUSH; 1887 } 1888 test DFSTATUS, FIFOEMP jz return; 1889BEGIN_CRITICAL; 1890 or LONGJMP_ADDR[1], INVALID_ADDR; 1891 mvi SCB_SCSI_STATUS, STATUS_PKT_SENSE; 1892 or SCB_CONTROL, STATUS_RCVD; 1893 jmp pkt_complete_scb_if_fifos_idle; 1894END_CRITICAL; 1895pkt_status_check_overrun: 1896 /* 1897 * Status PKT overruns are uncerimoniously recovered with a 1898 * bus reset. If we've overrun, let the host know so that 1899 * recovery can be performed. 1900 * 1901 * LAST_SEG_DONE has been observed. If either CTXTDONE or 1902 * a NONPACKREQ phase change have occurred and the FIFO is 1903 * empty, there is no overrun. 1904 */ 1905 test DFSTATUS, FIFOEMP jz pkt_status_report_overrun; 1906 test SEQINTSRC, CTXTDONE jz . + 2; 1907 test DFSTATUS, FIFOEMP jnz pkt_status_IU_done; 1908 test SCSIPHASE, ~DATA_PHASE_MASK jz return; 1909 test DFSTATUS, FIFOEMP jnz pkt_status_check_nonpackreq; 1910pkt_status_report_overrun: 1911 SET_SEQINTCODE(STATUS_OVERRUN) 1912 /* SEQUENCER RESTARTED */ 1913pkt_status_check_nonpackreq: 1914 /* 1915 * CTXTDONE may be held off if a NONPACKREQ is associated with 1916 * the current context. If a NONPACKREQ is observed, decide 1917 * if it is for the current context. If it is for the current 1918 * context, we must defer NONPACKREQ processing until all data 1919 * has transferred to the host. 1920 */ 1921 test SCSIPHASE, ~DATA_PHASE_MASK jz return; 1922 test SCSISIGO, ATNO jnz . + 2; 1923 test SSTAT2, NONPACKREQ jz return; 1924 test SEQINTSRC, CTXTDONE jnz pkt_status_IU_done; 1925 test DFSTATUS, FIFOEMP jz return; 1926 /* 1927 * The unexpected nonpkt phase handler assumes that any 1928 * data channel use will have a FIFO reference count. It 1929 * turns out that the status handler doesn't need a refernce 1930 * count since the status received flag, and thus completion 1931 * processing, cannot be set until the handler is finished. 1932 * We increment the count here to make the nonpkt handler 1933 * happy. 1934 */ 1935 inc SCB_FIFO_USE_COUNT; 1936 /* FALLTHROUGH */ 1937 1938/* 1939 * Nonpackreq is a polled status. It can come true in three situations: 1940 * we have received an L_Q, we have sent one or more L_Qs, or there is no 1941 * L_Q context associated with this REQ (REQ occurs immediately after a 1942 * (re)selection). Routines that know that the context responsible for this 1943 * nonpackreq call directly into unexpected_nonpkt_phase. In the case of the 1944 * top level idle loop, we exhaust all active contexts prior to determining that 1945 * we simply do not have the full I_T_L_Q for this phase. 1946 */ 1947unexpected_nonpkt_phase_find_ctxt: 1948 /* 1949 * This nonpackreq is most likely associated with one of the tags 1950 * in a FIFO or an outgoing LQ. Only treat it as an I_T only 1951 * nonpackreq if we've cleared out the FIFOs and handled any 1952 * pending SELDO. 1953 */ 1954SET_SRC_MODE M_SCSI; 1955SET_DST_MODE M_SCSI; 1956 and A, FIFO1FREE|FIFO0FREE, DFFSTAT; 1957 cmp A, FIFO1FREE|FIFO0FREE jne return; 1958 test SSTAT0, SELDO jnz return; 1959 mvi SCBPTR[1], SCB_LIST_NULL; 1960unexpected_nonpkt_phase: 1961 test MODE_PTR, ~(MK_MODE(M_DFF1, M_DFF1)) 1962 jnz unexpected_nonpkt_mode_cleared; 1963SET_SRC_MODE M_DFF0; 1964SET_DST_MODE M_DFF0; 1965 or LONGJMP_ADDR[1], INVALID_ADDR; 1966 dec SCB_FIFO_USE_COUNT; 1967 mvi DFFSXFRCTL, CLRCHN; 1968unexpected_nonpkt_mode_cleared: 1969 mvi CLRSINT2, CLRNONPACKREQ; 1970 test SCSIPHASE, ~(MSG_IN_PHASE|MSG_OUT_PHASE) jnz illegal_phase; 1971 SET_SEQINTCODE(ENTERING_NONPACK) 1972 jmp ITloop; 1973 1974illegal_phase: 1975 SET_SEQINTCODE(ILLEGAL_PHASE) 1976 jmp ITloop; 1977 1978/* 1979 * We have entered an overrun situation. If we have working 1980 * BITBUCKET, flip that on and let the hardware eat any overrun 1981 * data. Otherwise use an overrun buffer in the host to simulate 1982 * BITBUCKET. 1983 */ 1984pkt_handle_overrun_inc_use_count: 1985 inc SCB_FIFO_USE_COUNT; 1986pkt_handle_overrun: 1987 SET_SEQINTCODE(CFG4OVERRUN) 1988 call freeze_queue; 1989 if ((ahd->bugs & AHD_PKT_BITBUCKET_BUG) == 0) { 1990 or DFFSXFRCTL, DFFBITBUCKET; 1991SET_SRC_MODE M_DFF1; 1992SET_DST_MODE M_DFF1; 1993 } else { 1994 call load_overrun_buf; 1995 mvi DFCNTRL, (HDMAEN|SCSIEN|PRELOADEN); 1996 } 1997 call setjmp; 1998 if ((ahd->bugs & AHD_PKT_BITBUCKET_BUG) != 0) { 1999 test DFSTATUS, PRELOAD_AVAIL jz overrun_load_done; 2000 call load_overrun_buf; 2001 or DFCNTRL, PRELOADEN; 2002overrun_load_done: 2003 test SEQINTSRC, CTXTDONE jnz pkt_overrun_end; 2004 } else { 2005 test DFFSXFRCTL, DFFBITBUCKET jz pkt_overrun_end; 2006 } 2007 test SSTAT2, NONPACKREQ jz return; 2008pkt_overrun_end: 2009 or SCB_RESIDUAL_SGPTR, SG_OVERRUN_RESID; 2010 test SEQINTSRC, CTXTDONE jz unexpected_nonpkt_phase; 2011 dec SCB_FIFO_USE_COUNT; 2012 or LONGJMP_ADDR[1], INVALID_ADDR; 2013 test SCB_CONTROL, STATUS_RCVD jnz pkt_complete_scb_if_fifos_idle; 2014 mvi DFFSXFRCTL, CLRCHN ret; 2015 2016if ((ahd->bugs & AHD_PKT_BITBUCKET_BUG) != 0) { 2017load_overrun_buf: 2018 /* 2019 * Load a dummy segment if preload space is available. 2020 */ 2021 mov HADDR[0], SHARED_DATA_ADDR; 2022 add HADDR[1], PKT_OVERRUN_BUFOFFSET, SHARED_DATA_ADDR[1]; 2023 mov ACCUM_SAVE, A; 2024 clr A; 2025 adc HADDR[2], A, SHARED_DATA_ADDR[2]; 2026 adc HADDR[3], A, SHARED_DATA_ADDR[3]; 2027 mov A, ACCUM_SAVE; 2028 bmov HADDR[4], ALLZEROS, 4; 2029 /* PKT_OVERRUN_BUFSIZE is a multiple of 256 */ 2030 clr HCNT[0]; 2031 mvi HCNT[1], ((PKT_OVERRUN_BUFSIZE >> 8) & 0xFF); 2032 clr HCNT[2] ret; 2033} 2034