1 /* 2 * Copyright (c) 1990 University of Utah. 3 * Copyright (c) 1990, 1993 4 * The Regents of the University of California. All rights reserved. 5 * 6 * This code is derived from software contributed to Berkeley by 7 * the Systems Programming Group of the University of Utah Computer 8 * Science Department. 9 * 10 * %sccs.include.redist.c% 11 * 12 * from: Utah $Hdr: st.c 1.11 92/01/21$ 13 * 14 * @(#)st.c 8.4 (Berkeley) 05/27/94 15 */ 16 17 /* 18 * SCSI CCS (Command Command Set) tape driver. 19 * 20 * Specific to Exabyte: 21 * mt status: residual="Mbytes to LEOM" 22 * minor bit 4 [b1bbbb] (aka /dev/rst16) selects short filemarks 23 * minor bit 5 [1bbbbb] (aka /dev/rst32) selects fix block mode, 1k blocks. 24 * 25 * Archive drive: 26 * can read both QIC-24 and QIC-II. But only writes 27 * QIC-24. 28 * 29 * Supports Archive Viper QIC-150 tape drive, but scsi.c reports selection 30 * errors. 31 * 32 * Supports Archive Python DAT drive, but will sometimes hang machine. 33 * 34 * Supports HP 35450A DAT drive, but will sometimes hang machine. 35 * Partitioning of tape not supported. 36 * Vendor unique support has not been added. 37 * 38 * 39 * Supports Archive VIPER (QIC-150). 40 * Mostly Supports Archive PYTHON (DAT). 41 * Hangs if write after spin down. 42 * Need scsi.c that does connect/disconnect. 43 */ 44 45 /* 46 * support for the block device not implemented 47 */ 48 49 #include "st.h" 50 #if NST > 0 51 52 #include <sys/param.h> 53 #include <sys/systm.h> 54 #include <sys/buf.h> 55 #include <sys/file.h> 56 #include <sys/proc.h> 57 #include <sys/ioctl.h> 58 #include <sys/tty.h> 59 #include <sys/mtio.h> 60 #include <sys/kernel.h> 61 #include <sys/tprintf.h> 62 63 #include <hp/dev/device.h> 64 #include <hp300/dev/scsireg.h> 65 #include <hp300/dev/stvar.h> 66 67 extern int scsi_test_unit_rdy(); 68 extern int scsi_request_sense(); 69 extern int scsiustart(); 70 extern int scsigo(); 71 extern void scsifree(); 72 extern void scsireset(); 73 extern void scsi_delay(); 74 extern int scsi_tt_oddio(); 75 76 extern int scsi_immed_command(); 77 78 int stinit(), ststart(), stgo(), stintr(); 79 struct driver stdriver = { 80 stinit, "st", ststart, stgo, stintr, 81 }; 82 83 struct st_softc { 84 struct hp_device *sc_hd; 85 struct devqueue sc_dq; 86 long sc_blkno; /* (possible block device support?) */ 87 long sc_resid; /* (possible block device support?) */ 88 int sc_flags; 89 int sc_blklen; /* 0 = variable len records */ 90 int sc_filepos; /* file position on tape */ 91 long sc_numblks; /* number of blocks on tape */ 92 short sc_type; /* ansi scsi type */ 93 short sc_punit; /* physical unit (scsi lun) */ 94 short sc_tapeid; /* tape drive id */ 95 char sc_datalen[32]; /* additional data length on some commands */ 96 short sc_tticntdwn; /* interrupts between TTi display updates */ 97 tpr_t sc_ctty; 98 struct buf *sc_bp; 99 u_char sc_cmd; 100 } st_softc[NST]; 101 102 /* softc flags */ 103 #define STF_ALIVE 0x0001 104 #define STF_OPEN 0x0002 105 #define STF_WMODE 0x0004 106 #define STF_WRTTN 0x0008 107 #define STF_CMD 0x0010 108 #define STF_LEOT 0x0020 109 #define STF_MOVED 0x0040 110 111 struct st_mode st_mode[NST]; 112 113 /* 114 * Maybe this should not be global, but gives chance to get 115 * tape remaining, Rewrites/ECC, etc outside the driver 116 */ 117 static struct st_xsense { 118 struct scsi_xsense sc_xsense; /* data from sense */ 119 struct exb_xsense exb_xsense; /* additional info from exabyte */ 120 } st_xsense[NST]; 121 122 static struct scsi_fmt_cdb stcmd[NST]; 123 124 static struct scsi_fmt_cdb st_read_cmd = { 6, CMD_READ }; 125 static struct scsi_fmt_cdb st_write_cmd = { 6, CMD_WRITE }; 126 127 struct buf sttab[NST]; 128 struct buf stbuf[NST]; 129 130 #define UNIT(x) (minor(x) & 3) 131 #define stpunit(x) ((x) & 7) 132 133 #define STDEV_NOREWIND 0x04 134 #define STDEV_HIDENSITY 0x08 135 #define STDEV_EXSFMK 0x10 136 #define STDEV_FIXEDBLK 0x20 137 138 #ifdef DEBUG 139 int st_debug = 0x0000; 140 #define ST_OPEN 0x0001 141 #define ST_GO 0x0002 142 #define ST_FMKS 0x0004 143 #define ST_OPENSTAT 0x0008 144 #define ST_BRESID 0x0010 145 #define ST_ODDIO 0x0020 146 #endif 147 148 /* 149 * Patchable variable. If an even length read is requested a dma transfer is 150 * used. Only after the read will we find out if the read had an odd number 151 * of bytes. The HP98658 hardware cannot do odd length transfers, the last 152 * byte of the data will always be 0x00. Normally, the driver will complain 153 * about such transfers and return EIO. However, if st_dmaoddretry is non- 154 * zero, the driver will try and issue a BSR and then re-read the data using 155 * 'programmed transfer mode'. In most cases this works, however for unknown 156 * reasons it will hang the machine in certain cases. 157 * 158 * Note: 159 * Odd length read requests are always done using programmed transfer mode. 160 */ 161 int st_dmaoddretry = 0; 162 163 /* 164 * Exabyte only: 165 * From adb can have access to fixed vs. variable length modes. 166 * Use 0x400 for 1k (best capacity) fixed length records. 167 * In st_open, if minor bit 4 set then 1k records are used. 168 * If st_exblken is set to anything other then 0 we are in fixed length mode. 169 * Minor bit 5 requests 1K fixed-length, overriding any setting of st_exblklen. 170 */ 171 int st_exblklen = 0; 172 173 /* exabyte here for adb access, set at open time */ 174 #define EX_CT 0x80 /* international cart - more space W/P6 */ 175 #define EX_ND 0x20 /* no disconnect */ 176 #define EX_NBE 0x08 /* no busy enable */ 177 #define EX_EBD 0x04 /* even byte disconnect */ 178 #define EX_PE 0x02 /* parity enable */ 179 #define EX_NAL 0x01 /* no auto load */ 180 int st_exvup = (EX_CT|EX_ND|EX_NBE); /* vendor unique parameters */ 181 182 /* 183 * motion and reconnect thresholds guidelines: 184 * write operation; lower motion threshold for faster transfer 185 * raise reconnect threshold for slower transfer 186 * read operation; lower motion threshold for slower transfer 187 * raise reconnect threshold for faster transfer 188 */ 189 int st_exmotthr = 0x80; /* motion threshold, 0x80 default */ 190 int st_exreconthr = 0xa0; /* reconnect threshold, 0xa0 default */ 191 int st_exgapthr = 7; /* gap threshold, 7 default */ 192 #ifdef TTI 193 int st_extti = 0x01; /* bitmask of unit numbers, do extra */ 194 /* sensing so TTi display gets updated */ 195 #endif 196 197 stinit(hd) 198 register struct hp_device *hd; 199 { 200 register struct st_softc *sc = &st_softc[hd->hp_unit]; 201 register struct buf *bp; 202 203 for (bp = sttab; bp < &sttab[NST]; bp++) 204 bp->b_actb = &bp->b_actf; 205 sc->sc_hd = hd; 206 sc->sc_punit = stpunit(hd->hp_flags); 207 sc->sc_type = stident(sc, hd); 208 if (sc->sc_type < 0) 209 return(0); 210 sc->sc_dq.dq_ctlr = hd->hp_ctlr; 211 sc->sc_dq.dq_unit = hd->hp_unit; 212 sc->sc_dq.dq_slave = hd->hp_slave; 213 sc->sc_dq.dq_driver = &stdriver; 214 sc->sc_blkno = 0; 215 sc->sc_flags = STF_ALIVE; 216 return(1); 217 } 218 219 stident(sc, hd) 220 register struct st_softc *sc; 221 register struct hp_device *hd; 222 { 223 int unit; 224 int ctlr, slave; 225 int i, stat, inqlen; 226 char idstr[32]; 227 static int havest = 0; 228 struct st_inquiry { 229 struct scsi_inquiry inqbuf; 230 struct exb_inquiry exb_inquiry; 231 } st_inqbuf; 232 static struct scsi_fmt_cdb st_inq = { 233 6, 234 CMD_INQUIRY, 0, 0, 0, sizeof(st_inqbuf), 0 235 }; 236 237 ctlr = hd->hp_ctlr; 238 slave = hd->hp_slave; 239 unit = sc->sc_punit; 240 scsi_delay(-1); 241 242 inqlen = 0x05; /* min */ 243 st_inq.cdb[4] = 0x05; 244 stat = scsi_immed_command(ctlr, slave, unit, &st_inq, 245 (u_char *)&st_inqbuf, inqlen, B_READ); 246 /* do twice as first command on some scsi tapes always fails */ 247 stat = scsi_immed_command(ctlr, slave, unit, &st_inq, 248 (u_char *)&st_inqbuf, inqlen, B_READ); 249 if (stat == -1) 250 goto failed; 251 252 if ((st_inqbuf.inqbuf.type != 0x01 || /* sequential access device */ 253 st_inqbuf.inqbuf.qual != 0x80 || /* removable media */ 254 (st_inqbuf.inqbuf.version != 0x01 && /* current ANSI SCSI spec */ 255 st_inqbuf.inqbuf.version != 0x02)) /* 0x02 is for HP DAT */ 256 && 257 (st_inqbuf.inqbuf.type != 0x01 || /* M4 ??! */ 258 /* 259 * the M4 is a little too smart (ass?) for its own good: 260 * qual codes: 261 * 0x80: you can take the tape out (unit not online) 262 * 0xf8: online and at 6250bpi 263 * 0xf9: online and at 1600bpi 264 */ 265 st_inqbuf.inqbuf.version != 0x09)) /* M4 tape */ 266 { 267 printf("st: wrong specs: type %x qual %x version %d\n", st_inqbuf.inqbuf.type, 268 st_inqbuf.inqbuf.qual, st_inqbuf.inqbuf.version); 269 goto failed; 270 } 271 272 /* now get additonal info */ 273 inqlen = 0x05 + st_inqbuf.inqbuf.len; 274 st_inq.cdb[4] = inqlen; 275 bzero(&st_inqbuf, sizeof(st_inqbuf)); 276 stat = scsi_immed_command(ctlr, slave, unit, &st_inq, 277 (u_char *)&st_inqbuf, inqlen, B_READ); 278 279 if (st_inqbuf.inqbuf.len >= 28) { 280 bcopy((caddr_t)&st_inqbuf.inqbuf.vendor_id, (caddr_t)idstr, 28); 281 for (i = 27; i > 23; --i) 282 if (idstr[i] != ' ') 283 break; 284 idstr[i+1] = 0; 285 for (i = 23; i > 7; --i) 286 if (idstr[i] != ' ') 287 break; 288 idstr[i+1] = 0; 289 for (i = 7; i >= 0; --i) 290 if (idstr[i] != ' ') 291 break; 292 idstr[i+1] = 0; 293 printf("st%d: %s, %s rev %s\n", hd->hp_unit, idstr, &idstr[8], 294 &idstr[24]); 295 } else if (inqlen == 5) 296 /* great it's a stupid device, doesn't know it's know name */ 297 idstr[0] = idstr[8] = '\0'; 298 else 299 idstr[8] = '\0'; 300 301 if (stat == 0xff) { 302 printf("st%d: Cant handle this tape drive\n", hd->hp_unit); 303 goto failed; 304 } 305 306 if (bcmp("EXB-8200", &idstr[8], 8) == 0) { 307 sc->sc_tapeid = MT_ISEXABYTE; 308 sc->sc_datalen[CMD_REQUEST_SENSE] = 26; 309 sc->sc_datalen[CMD_INQUIRY] = 52; 310 sc->sc_datalen[CMD_MODE_SELECT] = 17; 311 sc->sc_datalen[CMD_MODE_SENSE] = 17; 312 } else if (bcmp("VIPER 150", &idstr[8], 9) == 0) { 313 sc->sc_tapeid = MT_ISVIPER1; 314 sc->sc_datalen[CMD_REQUEST_SENSE] = 14; 315 sc->sc_datalen[CMD_INQUIRY] = 36; 316 sc->sc_datalen[CMD_MODE_SELECT] = 12; 317 sc->sc_datalen[CMD_MODE_SENSE] = 12; 318 } else if (bcmp("Python 25501", &idstr[8], 12) == 0) { 319 sc->sc_tapeid = MT_ISPYTHON; 320 sc->sc_datalen[CMD_REQUEST_SENSE] = 14; 321 sc->sc_datalen[CMD_INQUIRY] = 36; 322 sc->sc_datalen[CMD_MODE_SELECT] = 12; 323 sc->sc_datalen[CMD_MODE_SENSE] = 12; 324 } else if (bcmp("HP35450A", &idstr[8], 8) == 0) { 325 /* XXX "extra" stat makes the HP drive happy at boot time */ 326 stat = scsi_test_unit_rdy(ctlr, slave, unit); 327 sc->sc_tapeid = MT_ISHPDAT; 328 sc->sc_datalen[CMD_REQUEST_SENSE] = 14; 329 sc->sc_datalen[CMD_INQUIRY] = 36; 330 sc->sc_datalen[CMD_MODE_SELECT] = 12; 331 sc->sc_datalen[CMD_MODE_SENSE] = 12; 332 } else if (bcmp("123107 SCSI", &idstr[8], 11) == 0 || 333 bcmp("OPEN REEL TAPE", &idstr[8], 14) == 0) { 334 sc->sc_tapeid = MT_ISMFOUR; 335 sc->sc_datalen[CMD_REQUEST_SENSE] = 8; 336 sc->sc_datalen[CMD_INQUIRY] = 5; 337 sc->sc_datalen[CMD_MODE_SELECT] = 12; 338 sc->sc_datalen[CMD_MODE_SENSE] = 12; 339 } else { 340 if (idstr[8] == '\0') 341 printf("st%d: No ID, assuming Archive\n", hd->hp_unit); 342 else 343 printf("st%d: Unsupported tape device\n", hd->hp_unit); 344 sc->sc_tapeid = MT_ISAR; 345 sc->sc_datalen[CMD_REQUEST_SENSE] = 8; 346 sc->sc_datalen[CMD_INQUIRY] = 5; 347 sc->sc_datalen[CMD_MODE_SELECT] = 12; 348 sc->sc_datalen[CMD_MODE_SENSE] = 12; 349 } 350 351 sc->sc_filepos = 0; 352 353 /* load xsense */ 354 stxsense(ctlr, slave, unit, sc); 355 356 scsi_delay(0); 357 /* XXX if we have a tape, we must up the delays in the HA driver */ 358 if (!havest) { 359 havest = 1; 360 scsi_delay(20000); 361 } 362 return(st_inqbuf.inqbuf.type); 363 failed: 364 scsi_delay(0); 365 return(-1); 366 } 367 368 stopen(dev, flag, type, p) 369 dev_t dev; 370 int flag, type; 371 struct proc *p; 372 { 373 register struct st_softc *sc = &st_softc[UNIT(dev)]; 374 register struct st_xsense *xsense; 375 register int count; 376 register int stat; 377 int ctlr, slave, unit; 378 struct mode_select_data msd; 379 struct mode_sense mode; 380 int modlen; 381 int error; 382 static struct scsi_fmt_cdb modsel = { 383 6, 384 CMD_MODE_SELECT, 0, 0, 0, sizeof(msd), 0 385 }; 386 static struct scsi_fmt_cdb modsense = { 387 6, 388 CMD_MODE_SENSE, 0, 0, 0, sizeof(mode), 0 389 }; 390 391 ctlr = sc->sc_dq.dq_ctlr; 392 slave = sc->sc_dq.dq_slave; 393 unit = sc->sc_punit; 394 xsense = &st_xsense[UNIT(dev)]; 395 396 if (UNIT(dev) > NST || (sc->sc_flags & STF_ALIVE) == 0) 397 return(ENXIO); 398 if (sc->sc_flags & STF_OPEN) 399 return(EBUSY); 400 401 /* 402 * Be prepared to print error messages 403 */ 404 sc->sc_ctty = tprintf_open(p); 405 406 /* do a mode sense to get current */ 407 modlen = sc->sc_datalen[CMD_MODE_SENSE]; 408 modsense.cdb[4] = modlen; 409 stat = scsi_immed_command(ctlr, slave, unit, &modsense, 410 (u_char *)&mode, modlen, B_READ); 411 412 /* do a mode sense to get current */ 413 modlen = sc->sc_datalen[CMD_MODE_SENSE]; 414 modsense.cdb[4] = modlen; 415 stat = scsi_immed_command(ctlr, slave, unit, &modsense, 416 (u_char *)&mode, modlen, B_READ); 417 418 /* set record length */ 419 switch (sc->sc_tapeid) { 420 case MT_ISAR: 421 sc->sc_blklen = 512; 422 break; 423 case MT_ISEXABYTE: 424 if (minor(dev) & STDEV_FIXEDBLK) 425 sc->sc_blklen = 0x400; 426 else 427 sc->sc_blklen = st_exblklen; 428 break; 429 case MT_ISHPDAT: 430 sc->sc_blklen = 512; 431 break; 432 case MT_ISVIPER1: 433 sc->sc_blklen = 512; 434 break; 435 case MT_ISPYTHON: 436 sc->sc_blklen = 512; 437 break; 438 case MT_ISMFOUR: 439 sc->sc_blklen = 0; 440 break; 441 default: 442 if ((mode.md.blklen2 << 16 | 443 mode.md.blklen1 << 8 | 444 mode.md.blklen0) != 0) 445 sc->sc_blklen = mode.md.blklen2 << 16 | 446 mode.md.blklen1 << 8 | 447 mode.md.blklen0; 448 else 449 sc->sc_blklen = 512; 450 } 451 452 /* setup for mode select */ 453 msd.rsvd1 = 0; 454 msd.rsvd2 = 0; 455 msd.rsvd3 = 0; 456 msd.buff = 1; 457 msd.speed = 0; 458 msd.blkdeslen = 0x08; 459 msd.density = 0; 460 msd.blks2 = 0; 461 msd.blks1 = 0; 462 msd.blks0 = 0; 463 msd.rsvd4 = 0; 464 msd.blklen2 = (sc->sc_blklen >> 16) & 0xff; 465 msd.blklen1 = (sc->sc_blklen >> 8) & 0xff; 466 msd.blklen0 = sc->sc_blklen & 0xff; 467 468 /* 469 * Do we have any density problems? 470 */ 471 472 switch (sc->sc_tapeid) { 473 case MT_ISAR: 474 if (minor(dev) & STDEV_HIDENSITY) 475 msd.density = 0x5; 476 else { 477 if (flag & FWRITE) { 478 uprintf("Can only write QIC-24\n"); 479 return(EIO); 480 } 481 msd.density = 0x4; 482 } 483 break; 484 case MT_ISEXABYTE: 485 if (minor(dev) & STDEV_HIDENSITY) 486 uprintf("EXB-8200 density support only\n"); 487 msd.vupb = (u_char)st_exvup; 488 msd.rsvd5 = 0; 489 msd.p5 = 0; 490 msd.motionthres = (u_char)st_exmotthr; 491 msd.reconthres = (u_char)st_exreconthr; 492 msd.gapthres = (u_char)st_exgapthr; 493 break; 494 case MT_ISHPDAT: 495 case MT_ISVIPER1: 496 case MT_ISPYTHON: 497 if (minor(dev) & STDEV_HIDENSITY) 498 uprintf("Only one density supported\n"); 499 break; 500 case MT_ISMFOUR: 501 break; /* XXX could do density select? */ 502 default: 503 uprintf("Unsupported drive\n"); 504 return(EIO); 505 } 506 507 modlen = sc->sc_datalen[CMD_MODE_SELECT]; 508 modsel.cdb[4] = modlen; 509 510 /* mode select */ 511 count = 0; 512 retryselect: 513 stat = scsi_immed_command(ctlr, slave, unit, &modsel, 514 (u_char *)&msd, modlen, B_WRITE); 515 /* 516 * First command after power cycle, bus reset or tape change 517 * will error. Try command again 518 */ 519 if (stat == STS_CHECKCOND) { 520 sc->sc_filepos = 0; 521 stxsense(ctlr, slave, unit, sc); 522 stat = scsi_immed_command(ctlr, slave, unit, &modsel, 523 (u_char *)&msd, modlen, B_WRITE); 524 #ifdef DEBUG 525 if (stat && (st_debug & ST_OPEN)) 526 printf("stopen: stat on mode select 0x%x second try\n", stat); 527 #endif 528 if (stat == STS_CHECKCOND) { 529 stxsense(ctlr, slave, unit, sc); 530 prtkey(UNIT(dev), sc); 531 } 532 if (stat) 533 return(EIO); 534 } 535 if (stat == -1 || stat == STS_BUSY) { 536 /* 537 * XXX it might just be that the bus is busy because 538 * another tape is doing a command. This would change 539 * with connect/disconnect, ie. the other drive would 540 * not hold onto the bus. 541 * 542 * Sleep on lbolt for up to 20 minutes (max time to FSF 543 * an exabyte to EOT: 16:xx minutes) 544 */ 545 if (++count > 60*20) { 546 uprintf("SCSI bus timeout\n"); 547 return(EBUSY); 548 } 549 if (error = tsleep((caddr_t)&lbolt, PZERO | PCATCH, 550 "st_scsiwait", 0)) 551 return (error); 552 goto retryselect; 553 } 554 555 /* drive ready ? */ 556 stat = scsi_test_unit_rdy(ctlr, slave, unit); 557 558 if (stat == STS_CHECKCOND) { 559 stxsense(ctlr, slave, unit, sc); 560 switch (sc->sc_tapeid) { 561 case MT_ISEXABYTE: 562 if ((xsense->sc_xsense.key & XSK_NOTRDY) && 563 xsense->exb_xsense.tnp) 564 uprintf("no cartridge\n"); 565 else if (xsense->sc_xsense.key & XSK_NOTRDY) 566 uprintf("cartridge not loaded\n"); 567 else if (xsense->sc_xsense.key & XSK_UNTATTEN) { 568 uprintf("new cart/power interrupt\n"); 569 stat = 0; 570 } else if ((xsense->sc_xsense.key & XSK_UNTATTEN) && 571 xsense->exb_xsense.tnp) 572 uprintf("cartridge unloading\n"); 573 else 574 prtkey(UNIT(dev), sc); 575 break; 576 case MT_ISMFOUR: 577 case MT_ISAR: 578 if (xsense->sc_xsense.key & XSK_UNTATTEN) 579 stat = scsi_test_unit_rdy(ctlr, slave, unit); 580 if (stat == STS_CHECKCOND) { 581 stxsense(ctlr, slave, unit, sc); 582 if (xsense->sc_xsense.key) 583 prtkey(UNIT(dev), sc); 584 } else { 585 sc->sc_filepos = 0; /* new tape */ 586 stat = 0; 587 } 588 break; 589 case MT_ISHPDAT: 590 case MT_ISVIPER1: 591 case MT_ISPYTHON: 592 if (xsense->sc_xsense.key & XSK_UNTATTEN) 593 stat = scsi_test_unit_rdy(ctlr, slave, unit); 594 if (stat == STS_CHECKCOND) { 595 stxsense(ctlr, slave, unit, sc); 596 if (xsense->sc_xsense.key) 597 prtkey(UNIT(dev), sc); 598 } 599 break; 600 default: 601 uprintf("st%d: not ready\n", UNIT(dev)); 602 prtkey(UNIT(dev), sc); 603 break; 604 } 605 } 606 if (stat) 607 return(EIO); 608 609 /* mode sense */ 610 modlen = sc->sc_datalen[CMD_MODE_SENSE]; 611 modsense.cdb[4] = modlen; 612 stat = scsi_immed_command(ctlr, slave, unit, &modsense, 613 (u_char *)&mode, modlen, B_READ); 614 #ifdef DEBUG 615 if (st_debug & ST_OPENSTAT) 616 prtmodstat(&mode); 617 #endif 618 619 if (stat == STS_CHECKCOND) { 620 stxsense(ctlr, slave, unit, sc); 621 #ifdef DEBUG 622 if (st_debug & ST_OPEN) 623 dumpxsense(xsense); 624 #endif 625 } 626 if (stat) 627 return(EIO); 628 629 if ((flag & FWRITE) && mode.md.wp) { 630 uprintf("st:%d write protected\n", UNIT(dev)); 631 return(EACCES); 632 } 633 634 /* save total number of blocks on tape */ 635 sc->sc_numblks = mode.md.numblk2 << 16 | 636 mode.md.numblk1 << 8 | 637 mode.md.numblk0; 638 639 if (xsense->sc_xsense.eom && !(sc->sc_flags & STF_LEOT)) 640 sc->sc_filepos = 0; 641 #ifdef DEBUG 642 if (st_debug & ST_FMKS) 643 printf("st%d: open filepos = %d\n", UNIT(dev), sc->sc_filepos); 644 #endif 645 646 sc->sc_flags |= (STF_OPEN); 647 if (flag & FWRITE) 648 sc->sc_flags |= STF_WMODE; 649 sc->sc_flags &= ~STF_MOVED; 650 651 #ifdef TTI 652 /* make stats available, also lit up TTi display */ 653 sc->sc_tticntdwn = 100; 654 #endif 655 stxsense(ctlr, slave, unit, sc); 656 657 return(0); 658 } 659 660 /*ARGSUSED*/ 661 stclose(dev, flag) 662 dev_t dev; 663 int flag; 664 { 665 register struct st_softc *sc = &st_softc[UNIT(dev)]; 666 register int hit = 0; 667 668 if ((sc->sc_flags & (STF_WMODE|STF_WRTTN)) == (STF_WMODE|STF_WRTTN)) { 669 /* 670 * Cartridge tapes don't do double EOFs on EOT. 671 * We assume that variable-block devices use double EOF. 672 */ 673 stcommand(dev, MTWEOF, 1); 674 if (sc->sc_blklen == 0) { 675 stcommand(dev, MTWEOF, 1); 676 stcommand(dev, MTBSR, 1); 677 } 678 hit++; 679 } 680 if ((minor(dev) & STDEV_NOREWIND) == 0) { 681 stcommand(dev, MTREW, 1); 682 hit++; 683 } 684 #ifdef NOTDEF 685 /* wait until more stable before trying [XXX Needed ?] */ 686 if (!hit && (sc->sc_flags & SFT_WMODE)) 687 /* force out any any bufferd write data */ 688 stcommand(dev, MTFSR, 0); 689 #endif 690 /* make stats available */ 691 stxsense(sc->sc_dq.dq_ctlr, sc->sc_dq.dq_slave, sc->sc_punit, sc); 692 693 sc->sc_flags &= ~(STF_OPEN|STF_WMODE|STF_WRTTN); 694 tprintf_close(sc->sc_ctty); 695 return(0); /* XXX */ 696 } 697 698 ststrategy(bp) 699 register struct buf *bp; 700 { 701 struct buf *dp; 702 int unit, s; 703 704 unit = UNIT(bp->b_dev); 705 dp = &sttab[unit]; 706 bp->b_actf = NULL; 707 s = splbio(); 708 bp->b_actb = dp->b_actb; 709 *dp->b_actb = bp; 710 dp->b_actb = &bp->b_actf; 711 if (dp->b_active == 0) { 712 dp->b_active = 1; 713 stustart(unit); 714 } 715 splx(s); 716 } 717 718 stustart(unit) 719 int unit; 720 { 721 if (scsireq(&st_softc[unit].sc_dq)) 722 ststart(unit); 723 } 724 725 ststart(unit) 726 int unit; 727 { 728 struct hp_device *hp = st_softc[unit].sc_hd; 729 730 if (scsiustart(hp->hp_ctlr)) 731 stgo(unit); 732 } 733 734 stgo(unit) 735 int unit; 736 { 737 register struct st_softc *sc = &st_softc[unit]; 738 register struct scsi_fmt_cdb *cmd; 739 register struct buf *bp = sttab[unit].b_actf; 740 struct hp_device *hp = sc->sc_hd; 741 int pad, stat; 742 long nblks; 743 744 if (sc->sc_flags & STF_CMD) { 745 cmd = &stcmd[unit]; 746 pad = 0; 747 } else { 748 cmd = bp->b_flags & B_READ ? &st_read_cmd : &st_write_cmd; 749 if (sc->sc_blklen) 750 cmd->cdb[1] |= 0x01; /* fixed mode */ 751 else 752 cmd->cdb[1] &= 0xfe; 753 if (bp->b_flags & B_READ) 754 sc->sc_flags &= ~STF_WRTTN; 755 else 756 sc->sc_flags |= STF_WRTTN; 757 758 if (sc->sc_blklen) { /* fixed mode */ 759 nblks = bp->b_bcount / sc->sc_blklen; 760 if (bp->b_bcount % sc->sc_blklen) { 761 tprintf(sc->sc_ctty, 762 "st%d: I/O not block aligned %d/%ld\n", 763 unit, sc->sc_blklen, bp->b_bcount); 764 cmd->cdb[1] &= 0xfe; /* force error */ 765 } 766 } else /* variable len */ 767 nblks = bp->b_bcount; 768 769 *(u_char *)(&cmd->cdb[2]) = (u_char) (nblks >> 16); 770 *(u_char *)(&cmd->cdb[3]) = (u_char) (nblks >> 8); 771 *(u_char *)(&cmd->cdb[4]) = (u_char) nblks; 772 /* 773 * Always Zero. We are either writing in variable 774 * length mode we are writing in fixed block mode, 775 * or we are going to do odd length IO and are not 776 * going to use DMA. 777 */ 778 pad = 0; 779 } 780 781 #ifdef DEBUG 782 if (st_debug & ST_GO) 783 printf("stgo: cmd len %d [0]0x%x [1]0x%x [2]0x%x [3]0x%x [4]0x%x [5]0x%x\n", 784 cmd->len, cmd->cdb[0], cmd->cdb[1], cmd->cdb[2], 785 cmd->cdb[3], cmd->cdb[4], cmd->cdb[5]); 786 #endif 787 788 sc->sc_flags |= STF_MOVED; 789 if (bp->b_bcount & 1) { 790 #ifdef DEBUG 791 if (st_debug & ST_ODDIO) 792 printf("stgo%d: odd count %d using manual transfer\n", 793 unit, bp->b_bcount); 794 #endif 795 stat = scsi_tt_oddio(hp->hp_ctlr, hp->hp_slave, sc->sc_punit, 796 bp->b_un.b_addr, bp->b_bcount, 797 bp->b_flags, 1); 798 if (stat == 0) { 799 bp->b_resid = 0; 800 stfinish(unit, sc, bp); 801 } 802 } else 803 stat = scsigo(hp->hp_ctlr, hp->hp_slave, sc->sc_punit, 804 bp, cmd, pad); 805 if (stat) { 806 bp->b_error = EIO; 807 bp->b_flags |= B_ERROR; 808 stxsense(sc->sc_dq.dq_ctlr, sc->sc_dq.dq_slave, 809 sc->sc_punit, sc); 810 sterror(unit, sc, stat); 811 stfinish(unit, sc, bp); 812 } 813 } 814 815 stfinish(unit, sc, bp) 816 int unit; 817 struct st_softc *sc; 818 struct buf *bp; 819 { 820 register struct buf *dp; 821 822 sttab[unit].b_errcnt = 0; 823 if (dp = bp->b_actf) 824 dp->b_actb = bp->b_actb; 825 else 826 sttab[unit].b_actb = bp->b_actb; 827 *bp->b_actb = dp; 828 iodone(bp); 829 scsifree(&sc->sc_dq); 830 if (sttab[unit].b_actf) 831 stustart(unit); 832 else 833 sttab[unit].b_active = 0; 834 } 835 836 stread(dev, uio) 837 dev_t dev; 838 struct uio *uio; 839 { 840 int unit = UNIT(dev); 841 842 return(physio(ststrategy, &stbuf[unit], dev, B_READ, minphys, uio)); 843 } 844 845 stwrite(dev, uio) 846 dev_t dev; 847 struct uio *uio; 848 { 849 int unit = UNIT(dev); 850 851 return(physio(ststrategy, &stbuf[unit], dev, B_WRITE, minphys, uio)); 852 } 853 854 /*ARGSUSED*/ 855 stdump(dev) 856 dev_t dev; 857 { 858 return(ENXIO); 859 } 860 861 /*ARGSUSED*/ 862 stioctl(dev, cmd, data, flag) 863 dev_t dev; 864 int cmd; 865 caddr_t data; 866 int flag; 867 { 868 register struct st_softc *sc = &st_softc[UNIT(dev)]; 869 register int cnt; 870 register struct mtget *mtget; 871 register struct st_xsense *xp = &st_xsense[UNIT(dev)]; 872 register struct mtop *op; 873 long resid; 874 875 switch (cmd) { 876 877 /* tape operation */ 878 case MTIOCTOP: 879 op = (struct mtop *)data; 880 switch (op->mt_op) { 881 882 case MTBSR: 883 case MTFSR: 884 if (sc->sc_tapeid == MT_ISAR) 885 return(ENXIO); 886 case MTWEOF: 887 case MTFSF: 888 case MTBSF: 889 cnt = (int)op->mt_count; 890 break; 891 892 case MTREW: 893 case MTOFFL: 894 cnt = 1; 895 break; 896 897 case MTNOP: 898 return(0); 899 default: 900 return(EINVAL); 901 } 902 if (cnt <= 0) 903 return(EINVAL); 904 stcommand(dev, (u_int)op->mt_op, cnt); 905 break; 906 907 /* drive status */ 908 case MTIOCGET: 909 mtget = (struct mtget *)data; 910 stxsense(sc->sc_dq.dq_ctlr, sc->sc_dq.dq_slave, 911 sc->sc_punit, sc); 912 mtget->mt_type = sc->sc_tapeid; 913 mtget->mt_dsreg = 0; 914 mtget->mt_erreg = ((xp->sc_xsense.valid << 15) | 915 (xp->sc_xsense.filemark << 14) | 916 (xp->sc_xsense.eom << 13) | 917 (xp->sc_xsense.ili << 12) | 918 (xp->sc_xsense.key << 8)); 919 920 if (sc->sc_tapeid == MT_ISEXABYTE) { 921 mtget->mt_dsreg = sc->sc_flags; 922 resid = (xp->exb_xsense.tplft2 << 16 | 923 xp->exb_xsense.tplft1 << 8 | 924 xp->exb_xsense.tplft0); 925 mtget->mt_resid = resid / 1000; 926 if (sc->sc_numblks - resid) 927 mtget->mt_erreg |= 928 (((xp->exb_xsense.rwerrcnt2 << 16 | 929 xp->exb_xsense.rwerrcnt1 << 8 | 930 xp->exb_xsense.rwerrcnt0) * 100) / 931 (sc->sc_numblks - resid)) & 0xff; 932 } else if (xp->sc_xsense.valid) { 933 resid = ((xp->sc_xsense.info1 << 24) | 934 (xp->sc_xsense.info2 << 16) | 935 (xp->sc_xsense.info3 << 8) | 936 (xp->sc_xsense.info4)); 937 if (sc->sc_blklen) /* if fixed mode */ 938 resid *= sc->sc_blklen; 939 mtget->mt_resid = resid; 940 } else 941 mtget->mt_resid = 0; 942 break; 943 944 default: 945 return(ENXIO); 946 } 947 return(0); 948 } 949 950 stintr(unit, stat) 951 int unit, stat; 952 { 953 register struct st_softc *sc = &st_softc[unit]; 954 register struct st_xsense *xp = &st_xsense[unit]; 955 register struct buf *bp = sttab[unit].b_actf; 956 struct hp_device *hp = sc->sc_hd; 957 958 #ifdef DEBUG 959 if (bp == NULL) { 960 printf("st%d: bp == NULL\n", unit); 961 return; 962 } 963 #endif 964 switch (stat) { 965 /* scsi command completed ok */ 966 case 0: 967 bp->b_resid = 0; 968 break; 969 970 /* more status */ 971 case STS_CHECKCOND: 972 stxsense(sc->sc_dq.dq_ctlr, sc->sc_dq.dq_slave, 973 sc->sc_punit, sc); 974 if (xp->sc_xsense.valid) { 975 bp->b_resid = (u_long)((xp->sc_xsense.info1 << 24) | 976 (xp->sc_xsense.info2 << 16) | 977 (xp->sc_xsense.info3 << 8) | 978 (xp->sc_xsense.info4)); 979 if (sc->sc_blklen) /* fixed mode */ 980 bp->b_resid *= sc->sc_blklen; 981 } 982 if (xp->sc_xsense.filemark) { 983 sc->sc_filepos++; 984 break; 985 } 986 if (xp->sc_xsense.key != XSK_NOSENCE 987 && xp->sc_xsense.key != XSK_NOTUSED1 988 && xp->sc_xsense.key != XSK_NOTUSEDC 989 && xp->sc_xsense.key != XSK_NOTUSEDE) { 990 sterror(unit, sc, stat); 991 bp->b_flags |= B_ERROR; 992 bp->b_error = EIO; 993 break; 994 } 995 if (xp->sc_xsense.ili) { 996 /* 997 * Fixed length blocks, an error. 998 */ 999 if (sc->sc_blklen) { 1000 tprintf(sc->sc_ctty, 1001 "st%d: Incorrect Length Indicator, blkcnt diff %d\n", 1002 unit, sc->sc_blklen - bp->b_resid); 1003 bp->b_flags |= B_ERROR; 1004 bp->b_error = EIO; 1005 break; 1006 } 1007 /* 1008 * Variable length but read more than requested, 1009 * an error. (XXX ??? wrong for 9 track?) 1010 */ 1011 if (bp->b_resid < 0) { 1012 bp->b_resid = 0; 1013 bp->b_flags |= B_ERROR; 1014 bp->b_error = ENOMEM; 1015 break; 1016 } 1017 /* 1018 * Variable length and odd, may require special 1019 * handling. 1020 */ 1021 if (bp->b_resid & 1 && (sc->sc_tapeid != MT_ISAR)) { 1022 /* 1023 * Normal behavior, treat as an error. 1024 */ 1025 if (!st_dmaoddretry) { 1026 tprintf(sc->sc_ctty, 1027 "st%d: Odd length read %d\n", 1028 UNIT(bp->b_dev), 1029 bp->b_bcount - bp->b_resid); 1030 bp->b_error = EIO; 1031 bp->b_flags |= B_ERROR; 1032 break; 1033 } 1034 /* 1035 * Attempt to back up and re-read using oddio. 1036 */ 1037 #ifdef DEBUG 1038 if (st_debug & ST_ODDIO) 1039 printf("st%d: stintr odd count %d, do BSR then oddio\n", 1040 UNIT(bp->b_dev), 1041 bp->b_bcount - bp->b_resid); 1042 #endif 1043 stat = scsi_tt_oddio(hp->hp_ctlr, hp->hp_slave, 1044 sc->sc_punit, 0, -1, 0, 0); 1045 if (stat == 0) 1046 stat = scsi_tt_oddio(hp->hp_ctlr, 1047 hp->hp_slave, 1048 sc->sc_punit, 1049 bp->b_un.b_addr, 1050 bp->b_bcount - bp->b_resid, 1051 bp->b_flags, 0); 1052 if (stat) { 1053 bp->b_error = EIO; 1054 bp->b_flags |= B_ERROR; 1055 stxsense(sc->sc_dq.dq_ctlr, sc->sc_dq.dq_slave, 1056 sc->sc_punit, sc); 1057 sterror(unit, sc, stat); 1058 } 1059 } 1060 break; 1061 } 1062 if (xp->sc_xsense.eom) { 1063 bp->b_flags |= B_ERROR; 1064 bp->b_error = ENOSPC; 1065 break; 1066 } 1067 tprintf(sc->sc_ctty, "st%d: unknown scsi error\n", unit); 1068 bp->b_flags |= B_ERROR; 1069 bp->b_error = EIO; 1070 break; 1071 1072 default: 1073 printf("st%d: stintr unknown stat 0x%x\n", unit, stat); 1074 break; 1075 } 1076 #ifdef DEBUG 1077 if ((st_debug & ST_BRESID) && bp->b_resid != 0) 1078 printf("b_resid %d b_flags 0x%x b_error 0x%x\n", 1079 bp->b_resid, bp->b_flags, bp->b_error); 1080 #endif 1081 /* asked for more filemarks then on tape */ 1082 if (bp->b_resid != 0 && 1083 (sc->sc_flags & STF_CMD) && sc->sc_cmd == CMD_SPACE) { 1084 sc->sc_filepos -= bp->b_resid; 1085 if (sc->sc_filepos < 0) 1086 sc->sc_filepos = 0; 1087 } 1088 1089 #ifdef TTI 1090 if (st_extti & (1<<unit) && 1091 sc->sc_type == MT_ISEXABYTE) /* to make display lit up */ 1092 /* 1093 * XXX severe performance penality for this. 1094 * Try and throttle by not calling stxsense on every intr. 1095 * Mostly for TTi we, get a stxsense call in open and close. 1096 */ 1097 if (sc->sc_tticntdwn-- == 0) { 1098 stxsense(sc->sc_dq.dq_ctlr, sc->sc_dq.dq_slave, 1099 sc->sc_punit, sc); 1100 sc->sc_tticntdwn = 100; 1101 } 1102 #endif 1103 1104 stfinish(unit, sc, bp); 1105 } 1106 1107 stcommand(dev, command, cnt) 1108 dev_t dev; 1109 u_int command; 1110 int cnt; 1111 { 1112 register struct st_softc *sc = &st_softc[UNIT(dev)]; 1113 register struct buf *bp = &stbuf[UNIT(dev)]; 1114 register struct scsi_fmt_cdb *cmd = &stcmd[UNIT(dev)]; 1115 register cmdcnt; 1116 int s; 1117 1118 cmd->len = 6; /* all tape commands are cdb6 */ 1119 cmd->cdb[1] = sc->sc_punit; 1120 cmd->cdb[2] = cmd->cdb[3] = cmd->cdb[4] = cmd->cdb[5] = 0; 1121 cmdcnt = 0; 1122 1123 /* 1124 * XXX Assumption is that everything except Archive can take 1125 * repeat count in cdb block. 1126 */ 1127 switch (command) { 1128 case MTWEOF: 1129 cmd->cdb[0] = CMD_WRITE_FILEMARK; 1130 if (sc->sc_tapeid != MT_ISAR) { 1131 cmdcnt = cnt; 1132 cnt = 1; 1133 } else 1134 cmdcnt = 1; 1135 *(u_char *)(&cmd->cdb[2]) = (u_char) (cmdcnt >> 16); 1136 *(u_char *)(&cmd->cdb[3]) = (u_char) (cmdcnt >> 8); 1137 *(u_char *)(&cmd->cdb[4]) = (u_char) cmdcnt; 1138 1139 if (sc->sc_tapeid == MT_ISEXABYTE && 1140 (minor(dev) & STDEV_EXSFMK)) /* short filemarks */ 1141 cmd->cdb[5] |= 0x80; 1142 else 1143 cmd->cdb[5] &= 0x7f; 1144 break; 1145 case MTBSF: 1146 /* Archive can't back up, will not get to BSR case */ 1147 if (sc->sc_tapeid == MT_ISAR) { 1148 if ((sc->sc_filepos - cnt) < 0) { 1149 stcommand(dev, MTREW, 1); 1150 return; 1151 } 1152 cmdcnt = sc->sc_filepos - cnt + 1; 1153 stcommand(dev, MTREW, 1); 1154 stcommand(dev, MTFSF, cmdcnt); 1155 return; 1156 } 1157 case MTBSR: 1158 case MTFSR: 1159 case MTFSF: 1160 if (command == MTBSF || command == MTBSR) 1161 cnt = cnt * (-1); /* backward move */ 1162 if (command == MTFSF || command == MTBSF) 1163 cmd->cdb[1] |= 0x01; /* filemarks */ 1164 else 1165 cmd->cdb[1] |= 0x00; /* logical blocks */ 1166 if (sc->sc_tapeid != MT_ISAR) { 1167 cmdcnt = cnt; 1168 cnt = 1; 1169 } else 1170 cmdcnt = 1; 1171 *(u_char *)(&cmd->cdb[2]) = (u_char) (cmdcnt >> 16); 1172 *(u_char *)(&cmd->cdb[3]) = (u_char) (cmdcnt >> 8); 1173 *(u_char *)(&cmd->cdb[4]) = (u_char) cmdcnt; 1174 cmd->cdb[0] = CMD_SPACE; 1175 break; 1176 case MTREW: 1177 cmd->cdb[0] = CMD_REWIND; 1178 sc->sc_filepos = 0; 1179 break; 1180 case MTOFFL: 1181 cmd->cdb[0] = CMD_LOADUNLOAD; 1182 sc->sc_filepos = 0; 1183 break; 1184 default: 1185 printf("st%d: stcommand bad command 0x%x\n", 1186 UNIT(dev), command); 1187 } 1188 1189 sc->sc_flags |= STF_CMD; 1190 sc->sc_cmd = cmd->cdb[0]; 1191 1192 sc->sc_bp = bp; 1193 again: 1194 #ifdef DEBUG 1195 if (st_debug & ST_FMKS) 1196 printf("st%d: stcommand filepos %d cmdcnt %d cnt %d\n", 1197 UNIT(dev), sc->sc_filepos, cmdcnt, cnt); 1198 #endif 1199 s = splbio(); 1200 while (bp->b_flags & B_BUSY) { 1201 if (bp->b_flags & B_DONE) 1202 break; 1203 bp->b_flags |= B_WANTED; 1204 sleep((caddr_t)bp, PRIBIO); 1205 } 1206 bp->b_flags = B_BUSY|B_READ; 1207 splx(s); 1208 bp->b_dev = dev; 1209 bp->b_bcount = 0; 1210 bp->b_resid = 0; 1211 bp->b_blkno = 0; 1212 bp->b_error = 0; 1213 ststrategy(bp); 1214 iowait(bp); 1215 if (bp->b_flags & B_WANTED) 1216 wakeup((caddr_t)bp); 1217 bp->b_flags &= B_ERROR; 1218 1219 if (command == MTWEOF || command == MTFSF || command == MTBSF) 1220 sc->sc_filepos += cmdcnt; 1221 1222 if (--cnt > 0) 1223 goto again; 1224 1225 sc->sc_flags |= STF_MOVED; 1226 sc->sc_flags &= ~(STF_CMD|STF_WRTTN); 1227 } 1228 1229 sterror(unit, sc, stat) 1230 int unit, stat; 1231 struct st_softc *sc; 1232 { 1233 /* stxsense must have been called before sterror() */ 1234 if (stat & STS_CHECKCOND) 1235 prtkey(unit, sc); 1236 else if (stat) 1237 tprintf(sc->sc_ctty, 1238 "st%d: bad scsi status 0x%x\n", unit, stat); 1239 1240 if ((sc->sc_flags & STF_CMD) && sc->sc_cmd == CMD_SPACE) /* fsf */ 1241 sc->sc_filepos--; 1242 } 1243 1244 stxsense(ctlr, slave, unit, sc) 1245 int ctlr, slave, unit; 1246 struct st_softc *sc; 1247 { 1248 u_char *sensebuf; 1249 unsigned len; 1250 1251 sensebuf = (u_char *)&st_xsense[sc->sc_dq.dq_unit]; 1252 len = sc->sc_datalen[CMD_REQUEST_SENSE]; 1253 scsi_request_sense(ctlr, slave, unit, sensebuf, len); 1254 } 1255 1256 prtkey(unit, sc) 1257 int unit; 1258 struct st_softc *sc; 1259 { 1260 register struct st_xsense *xp = &st_xsense[unit]; 1261 1262 switch (xp->sc_xsense.key) { 1263 case XSK_NOSENCE: 1264 break; 1265 case XSK_NOTUSED1: 1266 case XSK_NOTUSEDC: 1267 case XSK_NOTUSEDE: 1268 break; 1269 case XSK_REVERVED: 1270 tprintf(sc->sc_ctty, "st%d: Reserved sense key 0x%x\n", 1271 unit, xp->sc_xsense.key); 1272 break; 1273 case XSK_NOTRDY: 1274 tprintf(sc->sc_ctty, "st%d: NOT READY\n", unit); 1275 break; 1276 case XSK_MEDERR: 1277 tprintf(sc->sc_ctty, "st%d: MEDIUM ERROR\n", unit); 1278 break; 1279 case XSK_HRDWERR: 1280 tprintf(sc->sc_ctty, "st%d: HARDWARE ERROR\n", unit); 1281 break; 1282 case XSK_ILLREQ: 1283 tprintf(sc->sc_ctty, "st%d: ILLEGAL REQUEST\n", unit); 1284 break; 1285 case XSK_UNTATTEN: 1286 tprintf(sc->sc_ctty, "st%d: UNIT ATTENTION\n", unit); 1287 break; 1288 case XSK_DATAPROT: 1289 tprintf(sc->sc_ctty, "st%d: DATA PROTECT\n", unit); 1290 break; 1291 case XSK_BLNKCHK: 1292 tprintf(sc->sc_ctty, "st%d: BLANK CHECK\n", unit); 1293 break; 1294 case XSK_VENDOR: 1295 tprintf(sc->sc_ctty, "st%d: VENDER UNIQUE SENSE KEY ", unit); 1296 switch (sc->sc_tapeid) { 1297 case MT_ISEXABYTE: 1298 tprintf(sc->sc_ctty, "Exabyte: "); 1299 if (xp->exb_xsense.xfr) 1300 tprintf(sc->sc_ctty, 1301 "Transfer Abort Error\n"); 1302 if (xp->exb_xsense.tmd) 1303 tprintf(sc->sc_ctty, 1304 "Tape Mark Detect Error\n"); 1305 break; 1306 default: 1307 tprintf(sc->sc_ctty, "\n"); 1308 } 1309 break; 1310 case XSK_CPYABORT: 1311 tprintf(sc->sc_ctty, "st%d: COPY ABORTED\n", unit); 1312 break; 1313 case XSK_ABORTCMD: 1314 tprintf(sc->sc_ctty, "st%d: ABORTED COMMAND\n", unit); 1315 break; 1316 case XSK_VOLOVER: 1317 tprintf(sc->sc_ctty, "st%d: VOLUME OVERFLOW\n", unit); 1318 break; 1319 default: 1320 tprintf(sc->sc_ctty, "st%d: unknown sense key 0x%x\n", 1321 unit, xp->sc_xsense.key); 1322 } 1323 if (sc->sc_tapeid == MT_ISEXABYTE) { 1324 if (xp->exb_xsense.bpe) 1325 tprintf(sc->sc_ctty, "st%d: Bus Parity Errorn", unit); 1326 if (xp->exb_xsense.fpe) 1327 tprintf(sc->sc_ctty, 1328 "st%d: Formatted Buffer Parity Errorn", unit); 1329 if (xp->exb_xsense.eco) 1330 tprintf(sc->sc_ctty, "st%d: Error Counter Overflown", 1331 unit); 1332 if (xp->exb_xsense.tme) 1333 tprintf(sc->sc_ctty, "st%d: Tape Motion Errorn", unit); 1334 if (xp->exb_xsense.xfr) 1335 tprintf(sc->sc_ctty, "st%d: Transfer About Errorn", 1336 unit); 1337 if (xp->exb_xsense.tmd) 1338 tprintf(sc->sc_ctty, "st%d: Tape Mark Detect Errorn", 1339 unit); 1340 if (xp->exb_xsense.fmke) 1341 tprintf(sc->sc_ctty, "st%d: Filemark Errorn", unit); 1342 if (xp->exb_xsense.ure) 1343 tprintf(sc->sc_ctty, "st%d: Under Run Errorn", unit); 1344 if (xp->exb_xsense.sse) 1345 tprintf(sc->sc_ctty, "st%d: Servo System Errorn", 1346 unit); 1347 if (xp->exb_xsense.fe) 1348 tprintf(sc->sc_ctty, "st%d: Formatter Errorn", unit); 1349 if (xp->exb_xsense.wseb) 1350 tprintf(sc->sc_ctty, "st%d: WSEB Errorn", unit); 1351 if (xp->exb_xsense.wseo) 1352 tprintf(sc->sc_ctty, "st%d: WSEO Errorn", unit); 1353 } 1354 } 1355 1356 #ifdef DEBUG 1357 1358 dumpxsense(sensebuf) 1359 struct st_xsense *sensebuf; 1360 { 1361 struct st_xsense *xp = sensebuf; 1362 1363 printf("valid 0x%x errorclass 0x%x errorcode 0x%x\n", 1364 xp->sc_xsense.valid, 1365 xp->sc_xsense.class, xp->sc_xsense.code); 1366 printf("seg number 0x%x\n", xp->sc_xsense.segment); 1367 printf("FMK 0x%x EOM 0x%x ILI 0x%x RSVD 0x%x sensekey 0x%x\n", 1368 xp->sc_xsense.filemark, xp->sc_xsense.eom, xp->sc_xsense.ili, 1369 xp->sc_xsense.rsvd, xp->sc_xsense.key); 1370 printf("info 0x%lx\n", 1371 (u_long)((xp->sc_xsense.info1<<24)|(xp->sc_xsense.info2<<16)| 1372 (xp->sc_xsense.info3<<8)|(xp->sc_xsense.info4)) ); 1373 printf("ASenseL 0x%x\n", xp->sc_xsense.len); 1374 1375 if (xp->sc_xsense.len != 0x12) /* MT_ISEXB Exabyte only ?? */ 1376 return; /* What about others */ 1377 1378 printf("ASenseC 0x%x\n", xp->exb_xsense.addsens); 1379 printf("AsenseQ 0x%x\n", xp->exb_xsense.addsensq); 1380 printf("R/W Errors 0x%lx\n", 1381 (u_long)((xp->exb_xsense.rwerrcnt2<<16)| 1382 (xp->exb_xsense.rwerrcnt1<<8)| 1383 (xp->exb_xsense.rwerrcnt1)) ); 1384 printf("PF 0x%x BPE 0x%x FPE 0x%x ME 0x%x ECO 0x%x TME 0x%x TNP 0x%x BOT 0x%x\n", 1385 xp->exb_xsense.pf, xp->exb_xsense.bpe, xp->exb_xsense.fpe, 1386 xp->exb_xsense.me, xp->exb_xsense.eco, xp->exb_xsense.tme, 1387 xp->exb_xsense.tnp, xp->exb_xsense.bot); 1388 printf("XFR 0x%x TMD 0x%x WP 0x%x FMKE 0x%x URE 0x%x WE1 0x%x SSE 0x%x FE 0x%x\n", 1389 xp->exb_xsense.xfr, xp->exb_xsense.tmd, xp->exb_xsense.wp, 1390 xp->exb_xsense.fmke, xp->exb_xsense.ure, xp->exb_xsense.we1, 1391 xp->exb_xsense.sse, xp->exb_xsense.fe); 1392 printf("WSEB 0x%x WSEO 0x%x\n", 1393 xp->exb_xsense.wseb, xp->exb_xsense.wseo); 1394 printf("Remaining Tape 0x%lx\n", 1395 (u_long)((xp->exb_xsense.tplft2<<16)| 1396 (xp->exb_xsense.tplft1<<8)| 1397 (xp->exb_xsense.tplft0)) ); 1398 } 1399 1400 prtmodsel(msd, modlen) 1401 struct mode_select_data *msd; 1402 int modlen; 1403 { 1404 printf("Modsel command. len is 0x%x.\n", modlen); 1405 printf("rsvd1 0x%x rsvd2 0x%x rsvd3 0x%x bufferd 0x%x speed 0x%x bckdeslen 0x%x\n", 1406 msd->rsvd1,msd->rsvd2,msd->rsvd3,msd->buff,msd->speed,msd->blkdeslen); 1407 printf("density 0x%x blks2 0x%x blks1 0x%x blks0 0x%x rsvd 0x%x blklen2 0x%x blklen1 0x%x blklen0 0x%x\n", 1408 msd->density,msd->blks2,msd->blks1,msd->blks0,msd->rsvd4,msd->blklen2,msd->blklen1,msd->blklen0); 1409 printf("vupb 0x%x rsvd 0x%x p5 0x%x motionthres 0x%x reconthres 0x%x gapthres 0x%x \n", 1410 msd->vupb,msd->rsvd5,msd->p5,msd->motionthres,msd->reconthres,msd->gapthres); 1411 } 1412 1413 prtmodstat(mode) 1414 struct mode_sense *mode; 1415 { 1416 printf("Mode Status\n"); 1417 printf("sdl 0x%x medtype 0x%x wp 0x%x bfmd 0x%x speed 0x%x bdl 0x%x\n", 1418 mode->md.sdl, mode->md.medtype, mode->md.wp, mode->md.bfmd, 1419 mode->md.speed, mode->md.bdl); 1420 printf("dencod 0x%x numblk 0x%x blklen 0x%x\n", 1421 mode->md.dencod, 1422 (mode->md.numblk2<<16)|(mode->md.numblk1<<8)|(mode->md.numblk0), 1423 (mode->md.blklen2<<16)|(mode->md.blklen1<<8)|(mode->md.blklen0) ); 1424 printf("ct 0x%x nd 0x%x nbe 0x%x edb 0x%x pe 0x%x nal 0x%x p5 0x%x\n", 1425 mode->ex.ct, mode->ex.nd, mode->ex.nbe, 1426 mode->ex.ebd, mode->ex.pe, mode->ex.nal, mode->ex.p5); 1427 printf("motionthres 0x%x reconthres 0x%x gapthres 0x%x\n", 1428 mode->ex.motionthres, mode->ex.reconthres, mode->ex.gapthres); 1429 } 1430 #endif /* DEBUG */ 1431 1432 #endif 1433