1# Copyright (c) 1983, 1995 Eric P. Allman 2# Copyright (c) 1988 The Regents of the University of California. 3# All rights reserved. 4# 5# %sccs.include.redist.sh% 6# 7# @(#)READ_ME 8.91 (Berkeley) 05/25/95 8# 9 10This directory contains the source files for sendmail. 11 12For detailed instructions, please read the document ../doc/op.me: 13 14 eqn ../doc/op.me | pic | ditroff -me 15 16********************* 17!! DO NOT USE MAKE !! to compile sendmail -- instead, use the 18********************* "makesendmail" script located in the src 19directory. It will find an appropriate Makefile, and create an 20appropriate obj.* subdirectory so that multiplatform support 21works easily. 22 23The Makefile is for the new (4.4BSD) Berkeley make and uses syntax 24that is not recognized by older makes. It also has assumptions 25about the 4.4 file system layout built in. See below for details 26about other Makefiles. 27 28If you are porting to a new architecture for which there is no existing 29Makefile, you might start with Makefile.dist. This works on the old 30traditional make, but isn't customized for any particular architecture. 31 32 ************************************************** 33 ** Read below for more details of Makefiles. ** 34 ************************************************** 35 36************************************************************************** 37** IMPORTANT: DO NOT USE OPTIMIZATION (``-O'') IF YOU ARE RUNNING ** 38** GCC 2.4.x or 2.5.x. THERE IS A BUG IN THE GCC OPTIMIZER THAT ** 39** CAUSES SENDMAIL COMPILES TO FAIL MISERABLY. ** 40************************************************************************** 41 42Jim Wilson of Cygnus believes he has found the problem -- it will 43probably be fixed in GCC 2.5.6 -- but until this is verified, be 44very suspicious of gcc -O. 45 46This problem is reported to have been fixed in gcc 2.6. 47 48************************************************************************** 49** IMPORTANT: Read the appropriate paragraphs in the section on ** 50** ``Operating System and Compile Quirks''. ** 51************************************************************************** 52 53 54+-----------+ 55| MAKEFILES | 56+-----------+ 57 58By far, the easiest way to compile sendmail is to use the "makesendmail" 59script: 60 61 sh makesendmail 62 63This uses the "uname" command to figure out what architecture you are 64on and selects a proper Makefile accordingly. It also creates a 65subdirectory per object format, so that multiarchitecture support is 66easy. In general this should be all you need. However, if for some 67reason this doesn't work (e.g., NeXT systems don't have the "uname" 68command) you may have to set up your compile environment by hand. 69 70The "Makefile"s in these directories are from 4.4 BSD, and hence 71really only work properly if you are on a 4.4 system. In particular, 72they use new syntax that will not be recognized on old make programs, 73and some of them do things like ``.include ../../Makefile.inc'' to 74pick up some system defines. If you are getting sendmail separately, 75these files won't be included in the distribution, as they are 76outside of the sendmail tree. 77 78Instead, you should use one of the other Makefiles, such as 79Makefile.SunOS for a SunOS system, and so forth. These should 80work with the version of make that is appropriate for that 81system. All other Makefiles are in the "src/Makefiles" subdirectory. 82They use the version of make that is native for that system. These 83are the Makefiles that I use, and they have "Berkeley quirks" in them. 84I can't guarantee that they will work unmodified in your environment. 85In particular, Many of them include -I/usr/sww/include/db and 86-L/usr/sww/lib -- these are Berkeley's locations in the ``Software 87Warehouse'' for the new database libraries, described below. You don't 88have to remove these definitions if you don't have these directories, 89but you may have to remove -DNEWDB from the DBMDEF definition. 90 91Please look for an appropriate Makefile before you start trying to 92compile with Makefile or Makefile.dist. 93 94If you want to port the new Berkeley make, you can get it from 95ftp.uu.net in the directory /systems/unix/bsd-sources/usr.bin/make. 96Diffs and instructions for building this version of make under 97SunOS 4.1.x are available on ftp.css.itd.umich.edu in 98/pub/systems/sun/Net2-make.sun4.diff.Z. Diffs and instructions 99for building this version of make under IBM AIX 3.2.4 are available 100on ftp.uni-stuttgart.de in /sw/src/patches/bsd-make-rus-patches. 101For Ultrix, try ftp.vix.com:~ftp/pub/patches/pmake-for-ultrix.Z. 102Paul Southworth <pauls@umich.edu> published a description of porting 103this make in comp.unix.bsd. 104 105The complete text of the Makefile.inc that is in the parent of the 106sendmail directory is: 107 108 # @(#)Makefile.inc 8.1 (Berkeley) 6/6/93 109 110 BINDIR?= /usr/sbin 111 112 113+----------------------+ 114| DATABASE DEFINITIONS | 115+----------------------+ 116 117There are several database formats that can be used for the alias files 118and for general maps. When used for alias files they interact in an 119attempt to be back compatible. 120 121The three options are NEWDB (the new Berkeley DB package), NDBM (the 122older DBM implementation -- the very old V7 implementation is no 123longer supported), and NIS (Network Information Services). Used alone 124these just include the support they indicate. [If you are using NEWDB, 125get the latest version from FTP.CS.Berkeley.EDU in /ucb/4bsd/db.tar.Z 126(or db.tar.gz). DO NOT use the version from the Net2 distribution! 127However, if you are on BSD/386 or 386BSD-based systems, use the one 128that already exists on your system. You may need to #define OLD_NEWDB 1291 to do this.] 130 131[NOTE WELL: it is CRITICAL that you remove ndbm.o from libdb.a and 132ndbm.h from the appropriate include directories if you want to get 133ndbm support. These files OVERRIDE calls to ndbm routines -- in 134particular, if you leave ndbm.h in, you can find yourself using 135the new db package even if you don't define NEWDB.] 136 137If NEWDB and NDBM are defined (but not NIS), then sendmail will read 138NDBM format alias files, but the next time a newaliases is run the 139format will be converted to NEWDB; that format will be used forever 140more. This is intended as a transition feature. [Note however that 141the NEWDB library also catches and maps NDBM calls; you will have to 142back out this feature to get this to work. See ``Quirks'' section 143below for details.] 144 145If all three are defined and the name of the file includes the string 146"/yp/", sendmail will rebuild BOTH the NEWDB and NDBM format alias 147files. However, it will only read the NEWDB file; the NDBM format file 148is used only by the NIS subsystem. 149 150If NDBM and NIS are defined (regardless of the definition of NEWDB), 151and the filename includes the string "/yp/", sendmail adds the special 152tokens "YP_LAST_MODIFIED" and "YP_MASTER_NAME", both of which are 153required if the NDBM file is to be used as an NIS map. 154 155There is also preliminary support for NIS+ (-DNISPLUS), Hesiod 156(-DHESIOD), and NetInfo (-DNETINFO). These have not been well 157tested. 158 159All of -DNEWDB, -DNDBM, -DNIS, -DNISPLUS, -DHESIOD, and -DNETINFO are 160normally defined in the DBMDEF line in the Makefile. 161 162 163+---------------+ 164| COMPILE FLAGS | 165+---------------+ 166 167Whereever possible, I try to make sendmail pull in the correct 168compilation options needed to compile on various environments based on 169automatically defined symbols. Some machines don't seem to have useful 170symbols availble, requiring the following compilation flags in the 171Makefile: 172 173SOLARIS Define this if you are running Solaris 2.0 or higher. 174SOLARIS_2_3 Define this if you are running Solaris 2.3 or higher. 175SUNOS403 Define this if you are running SunOS 4.0.3. 176NeXT Define this if you are on a NeXT box. (This one may 177 be pre-defined for you.) There are other hacks you 178 have to make -- see below. 179_AIX3 Define this if you are IBM AIX 3.x. 180RISCOS Define this if you are running RISC/os from MIPS. 181IRIX Define this if you are running IRIX from SGI. 182_SCO_unix_ Define this if you are on SCO UNIX. 183_SCO_unix_4_2 Define this if you are on SCO Open Server 3.2v4. 184DGUX Define this if you are on DG/UX 5.4.3 or later 185DGUX_5_4_2 Define this if you are on DG/UX systems prior to 5.4.3. 186NonStop_UX_BXX Define this if you are on a Tandem NonStop-UX release 187 Bxx system. 188IRIX64 Define this if you are on an IRIX64 system. 189 190If you are a system that sendmail has already been ported to, you 191probably won't have to touch these. But if you are porting, you may 192have to tweak the following compilation flags in conf.h in order to 193get it to compile and link properly: 194 195SYSTEM5 Adjust for System V (not necessarily Release 4). 196SYS5SIGNALS Use System V signal semantics -- the signal handler 197 is automatically dropped when the signal is caught. 198 If this is not set, use POSIX/BSD semantics, where the 199 signal handler stays in force until an exec or an 200 explicit delete. Implied by SYSTEM5. 201SYS5SETPGRP Use System V setpgrp() semantics. Implied by SYSTEM5. 202HASFLOCK Set this if you prefer to use the flock(2) system call 203 rather than using fcntl-based locking. Fcntl locking 204 has some semantic gotchas, but many vendor systems 205 also interface it to lockd(8) to do NFS-style locking. 206 For this reason, this should not be set unless you 207 don't have an alternative. 208HASUNAME Set if you have the "uname" system call. Implied by 209 SYSTEM5. 210HASUNSETENV Define this if your system library has the "unsetenv" 211 subroutine. 212HASSETSID Define this if you have the setsid(2) system call. This 213 is implied if your system appears to be POSIX compliant. 214HASINITGROUPS Define this if you have the initgroups(3) routine. 215HASSETVBUF Define this if you have the setvbuf(3) library call. 216 If you don't, setlinebuf will be used instead. This 217 defaults on if your compiler defines __STDC__. 218HASSETREUID Define this if you have setreuid(2) ***AND*** root can 219 use setreuid to change to an arbitrary user. This second 220 condition is not satisfied on AIX 3.x. You may find that 221 your system has setresuid(2), (for example, on HP-UX) in 222 which case you will also have to #define setreuid(r, e) 223 to be the appropriate call. Some systems (such as Solaris) 224 have a compatibility routine that doesn't work properly, 225 but may have "saved user ids" properly implemented so you 226 can ``#define setreuid(r, e) seteuid(e)'' and have it work. 227 The important thing is that you have a call that will set 228 the effective uid independently of the real or saved uid 229 and be able to set the effective uid back again when done. 230 There's a test program in ../test/t_setreuid.c that will 231 try things on your system. Setting this improves the 232 security, since sendmail doesn't have to read .forward 233 and :include: files as root. There are certain attacks 234 that may be unpreventable without this call. 235USESETEUID Define this to 1 if you have seteuid(2) if you have a seteuid 236 system call that will allow root to set only the effective 237 user id to an arbitrary value ***AND*** you have saved user 238 ids. This is preferable to HASSETREUID if these conditions 239 are fulfilled. These are the semantics of the to-be-released 240 revision of Posix.1. The test program ../test/t_seteuid.c 241 will try this out on your system. If you define both 242 HASSETREUID and USESETEUID, the former is ignored. 243HASLSTAT Define this if you have symbolic links (and thus the 244 lstat(2) system call). This improves security. Unlike 245 most other options, this one is on by default, so you 246 need to #undef it in conf.h if you don't have symbolic 247 links (these days everyone does). 248HASSETRLIMIT Define this to 1 if you have the setrlimit(2) syscall. 249 You can define it to 0 to force it off. It is assumed 250 if you are running a BSD-like system. 251HASULIMIT Define this if you have the ulimit(2) syscall (System V 252 style systems). HASSETRLIMIT overrides, as it is more 253 general. 254NEEDGETOPT Define this if you need a reimplementation of getopt(3). 255 On some systems, getopt does very odd things if called 256 to scan the arguments twice. This flag will ask sendmail 257 to compile in a local version of getopt that works 258 properly. 259NEEDSTRTOL Define this if your standard C library does not define 260 strtol(3). This will compile in a local version. 261NEEDVPRINTF Define this if your standard C library does not define 262 vprintf(3). Note that the resulting fake implementation 263 is not very elegant and may not even work on some 264 architectures. 265NEEDFSYNC Define this if your standard C library does not define 266 fsync(2). This will try to simulate the operation using 267 fcntl(2); if that is not available it does nothing, which 268 isn't great, but at least it compiles and runs. 269HASGETUSERSHELL Define this to 1 if you have getusershell(3) in your 270 standard C library. If this is not defined, or is defined 271 to be 0, sendmail will scan the /etc/shells file (no 272 NIS-style support, defaults to /bin/sh and /bin/csh if 273 that file does not exist) to get a list of unrestricted 274 user shells. This is used to determine whether users 275 are allowed to forward their mail to a program or a file. 276GIDSET_T The type of entries in a gidset passed as the second 277 argument to getgroups(2). Historically this has been an 278 int, so this is the default, but some systems (such as 279 IRIX) pass it as a gid_t, which is an unsigned short. 280 This will make a difference, so it is important to get 281 this right! However, it is only an issue if you have 282 group sets. 283SLEEP_T The type returned by the system sleep() function. 284 Defaults to "unsigned int". Don't worry about this 285 if you don't have compilation problems. 286ARBPTR_T The type of an arbitrary pointer -- defaults to "void *". 287 If you are an very old compiler you may need to define 288 this to be "char *". 289LA_TYPE The type of load average your kernel supports. These 290 can be one of: 291 LA_ZERO (1) -- it always returns the load average as 292 "zero" (and does so on all architectures). 293 LA_INT (2) to read /dev/kmem for the symbol avenrun and 294 interpret as a long integer. 295 LA_FLOAT (3) same, but interpret the result as a floating 296 point number. 297 LA_SHORT (6) to interpret as a short integer. 298 LA_SUBR (4) if you have the getloadavg(3) routine in your 299 system library. 300 LA_MACH (5) to use MACH-style load averages (calls 301 processor_set_info()), 302 LA_PROCSTR (7) to read /proc/loadavg and interpret it 303 as a string representing a floating-point 304 number (Linux-style). 305 LA_READKSYM (8) is an implementation suitable for some 306 versions of SVr4 that uses the MIOC_READKSYM ioctl 307 call to read /dev/kmem. 308 LA_DGUX (9) is a special implementation for DG/UX that uses 309 the dg_sys_info system call. 310 LA_HPUX (10) is an HP-UX specific version that uses the 311 pstat_getdynamic system call. 312 LA_INT, LA_SHORT, LA_FLOAT, and LA_READKSYM have several 313 other parameters that they try to divine: the name of your 314 kernel, the name of the variable in the kernel to examine, 315 the number of bits of precision in a fixed point load average, 316 and so forth. 317 In desperation, use LA_ZERO. The actual code is in 318 conf.c -- it can be tweaked if you are brave. 319FSHIFT For LA_INT, LA_SHORT, and LA_READKSYM, this is the number 320 of bits of load average after the binary point -- i.e., 321 the number of bits to shift right in order to scale the 322 integer to get the true integer load average. Defaults to 8. 323_PATH_UNIX The path to your kernel. Needed only for LA_INT, LA_SHORT, 324 and LA_FLOAT. Defaults to "/unix" on System V, "/vmunix" 325 everywhere else. 326LA_AVENRUN For LA_INT, LA_SHORT, and LA_FLOAT, the name of the kernel 327 variable that holds the load average. Defaults to "avenrun" 328 on System V, "_avenrun" everywhere else. 329SFS_TYPE Encodes how your kernel can locate the amount of free 330 space on a disk partition. This can be set to SFS_NONE 331 (0) if you have no way of getting this information, 332 SFS_USTAT (1) if you have the ustat(2) system call, 333 SFS_4ARGS (2) if you have a four-argument statfs(2) 334 system call (and the include file is <sys/statfs.h>), 335 SFS_VFS (3), SFS_MOUNT (4), SFS_STATFS (5) if you have 336 the two-argument statfs(2) system call with includes in 337 <sys/vfs.h>, <sys/mount.h>, or <sys/statfs.h> respectively, 338 or SFS_STATVFS (6) if you have the two-argument statvfs(2) 339 call. The default if nothing is defined is SFS_NONE. 340SFS_BAVAIL with SFS_4ARGS hou can also set SFS_BAVAIL to the field name 341 in the statfs structure that holds the useful information; 342 this defaults to f_bavail. 343SPT_TYPE Encodes how your system can display what a process is doing 344 on a ps(1) command (SPT stands for Set Process Title). Can 345 be set to: 346 SPT_NONE (0) -- Don't try to set the process title at all. 347 SPT_REUSEARGV (1) -- Pad out your argv with the information; 348 this is the default if none specified. 349 SPT_BUILTIN (2) -- The system library has setproctitle. 350 SPT_PSTAT (3) -- Use the PSTAT_SETCMD option to pstat(2) 351 to set the process title; this is used by HP-UX. 352 SPT_PSSTRINGS (4) -- Use the magic PS_STRINGS pointer (4.4BSD). 353SPT_PADCHAR Character used to pad the process title; if undefined, 354 the space character (0x20) is used. This is ignored if 355 SPT_TYPE != SPT_REUSEARGV 356ERRLIST_PREDEFINED 357 If set, assumes that some header file defines sys_errlist. 358 This may be needed if you get type conflicts on this 359 variable -- otherwise don't worry about it. 360WAITUNION The wait(2) routine takes a "union wait" argument instead 361 of an integer argument. This is for compatibility with 362 old versions of BSD. 363SCANF You can set this to extend the F command to accept a 364 scanf string -- this gives you a primitive parser for 365 class definitions -- BUT it can make you vulnerable to 366 core dumps if the target file is poorly formed. 367SYSLOG_BUFSIZE You can define this to be the size of the buffer that 368 syslog accepts. If it is not defined, it assumes a 369 1024-byte buffer. If the buffer is very small (under 370 256 bytes) the log message format changes -- each 371 e-mail message will log many more messages, since it 372 will log each piece of information as a separate line 373 in syslog. 374BROKEN_RES_SEARCH 375 On Ultrix (and maybe other systems?) if you use the 376 res_search routine with an unknown host name, it returns 377 -1 but sets h_errno to 0 instead of HOST_NOT_FOUND. If 378 you set this, sendmail considers 0 to be the same as 379 HOST_NOT_FOUND. 380NAMELISTMASK If defined, values returned by nlist(3) are masked 381 against this value before use -- a common value is 382 0x7fffffff to strip off the top bit. 383BSD4_4_SOCKADDR If defined, socket addresses have an sa_len field that 384 defines the length of this address. 385 386 387 388+-----------------------+ 389| COMPILE-TIME FEATURES | 390+-----------------------+ 391 392There are a bunch of features that you can decide to compile in, such 393as selecting various database packages and special protocol support. 394Several are assumed based on other compilation flags -- if you want to 395"un-assume" something, you probably need to edit conf.h. Compilation 396flags that add support for special features include: 397 398NDBM Include support for "new" DBM library for aliases and maps. 399 Normally defined in the Makefile. 400NEWDB Include support for Berkeley "db" package (hash & btree) 401 for aliases and maps. Normally defined in the Makefile. 402OLD_NEWDB If non-zero, the version of NEWDB you have is the old 403 one that does not include the "fd" call. This call was 404 added in version 1.5 of the Berkeley DB code. If you 405 use -DOLD_NEWDB=0 it forces you to use the new interface. 406NIS Define this to get NIS (YP) support for aliases and maps. 407 Normally defined in the Makefile. 408NISPLUS Define this to get NIS+ support for aliases and maps. 409 Normally defined in the Makefile. 410HESIOD Define this to get Hesiod support for aliases and maps. 411 Normally defined in the Makefile. 412NETINFO Define this to get NeXT NetInfo support for aliases and maps. 413 Normally defined in the Makefile. 414USERDB Include support for the User Information Database. Implied 415 by NEWDB in conf.h. 416IDENTPROTO Define this as 1 to get IDENT (RFC 1413) protocol support. 417 This is assumed unless you are running on Ultrix or 418 HP-UX, both of which have a problem in the UDP 419 implementation. You can define it to be 0 to explicitly 420 turn off IDENT protocol support. If defined off, the code 421 is actually still compiled in, but it defaults off; you 422 can turn it on by setting the IDENT timeout to 30s in the 423 configuration file. 424IP_SRCROUTE Define this to 1 to get IP source routing information 425 displayed in the Received: header. This is assumed on 426 most systems, but some (e.g., Ultrix) apparently have a 427 broken version of getsockopt that doesn't properly 428 support the IP_OPTIONS call. You probably want this if 429 your OS can cope with it. Symptoms of failure will be that 430 it won't compile properly (that is, no support for fetching 431 IP_OPTIONs), or it compiles but source-routed TCP connections 432 either refuse to open or open and hang for no apparent reason. 433 Ultrix and AIX are known to fail this way. 434LOG Set this to get syslog(3) support. Defined by default 435 in conf.h. You want this if at all possible. 436NETINET Set this to get TCP/IP support. Defined by default 437 in conf.h. You probably want this. 438NETISO Define this to get ISO networking support. 439SMTP Define this to get the SMTP code. Implied by NETINET 440 or NETISO. 441NAMED_BIND If non-zero, include DNS (name daemon) support, including 442 MX support. The specs you must use this if you run 443 SMTP. Defined by default in conf.h. 444QUEUE Define this to get queueing code. Implied by NETINET 445 or NETISO; required by SMTP. This gives you other good 446 stuff -- it should be on. 447DAEMON Define this to get general network support. Implied by 448 NETINET or NETISO. Defined by default in conf.h. You 449 almost certainly want it on. 450MATCHGECOS Permit fuzzy matching of user names against the full 451 name (GECOS) field in the /etc/passwd file. This should 452 probably be on, since you can disable it from the config 453 file if you want to. Defined by default in conf.h. 454MIME8TO7 If non-zero, include 8 to 7 bit MIME conversions. This 455 also controls advertisement of 8BITMIME in the ESMTP 456 startup dialogue. 457MIME7TO8 If non-zero, include 7 to 8 bit MIME conversions. Not yet 458 implemented. 459 460 461+---------------------+ 462| DNS/RESOLVER ISSUES | 463+---------------------+ 464 465Many systems have old versions of the resolver library. At a minimum, 466you should be running BIND 4.8.3; older versions may compile, but they 467have known bugs that should give you pause. 468 469Common problems in old versions include "undefined" errors for 470dn_skipname. 471 472Some people have had a problem with BIND 4.9; it uses some routines 473that it expects to be externally defined such as strerror(). It may 474help to link with "-l44bsd" to solve this problem. 475 476!PLEASE! be sure to link with the same version of the resolver as 477the header files you used -- some people have used the 4.9 headers 478and linked with BIND 4.8 or vice versa, and it doesn't work. 479Unfortunately, it doesn't fail in an obvious way -- things just 480subtly don't work. 481 482 483+-------------------------------------+ 484| OPERATING SYSTEM AND COMPILE QUIRKS | 485+-------------------------------------+ 486 487GCC 2.5.x problems *** IMPORTANT *** 488 Date: Mon, 29 Nov 93 19:08:44 PST 489 From: wilson@cygnus.com (Jim Wilson) 490 Message-Id: <9311300308.AA04608@cygnus.com> 491 To: kenner@vlsi1.ultra.nyu.edu 492 Subject: [cattelan@thebarn.com: gcc 2.5.4-2.5.5 -O bug] 493 Cc: cattelan@thebarn.com, rms@gnu.ai.mit.edu, sendmail@cs.berkeley.edu 494 495 This fixes a problem that occurs when gcc 2.5.5 is used to compile 496 sendmail 8.6.4 with optimization on a sparc. 497 498 Mon Nov 29 19:00:14 1993 Jim Wilson (wilson@sphagnum.cygnus.com) 499 500 * reload.c (find_reloads_toplev): Replace obsolete reference to 501 BYTE_LOADS_*_EXTEND with LOAD_EXTEND_OP. 502 503 *** clean-ss-931128/reload.c Sun Nov 14 16:20:01 1993 504 --- ss-931128/reload.c Mon Nov 29 18:52:55 1993 505 *************** find_reloads_toplev (x, opnum, type, ind 506 *** 3888,3894 **** 507 force a reload in that case. So we should not do anything here. */ 508 509 else if (regno >= FIRST_PSEUDO_REGISTER 510 ! #if defined(BYTE_LOADS_ZERO_EXTEND) || defined(BYTE_LOADS_SIGN_EXTEND) 511 && (GET_MODE_SIZE (GET_MODE (x)) 512 <= GET_MODE_SIZE (GET_MODE (SUBREG_REG (x)))) 513 #endif 514 --- 3888,3894 ---- 515 force a reload in that case. So we should not do anything here. */ 516 517 else if (regno >= FIRST_PSEUDO_REGISTER 518 ! #ifdef LOAD_EXTEND_OP 519 && (GET_MODE_SIZE (GET_MODE (x)) 520 <= GET_MODE_SIZE (GET_MODE (SUBREG_REG (x)))) 521 #endif 522 523 524SunOS 4.x (Solaris 1.x) 525 You may have to use -lresolv on SunOS. However, beware that 526 this links in a new version of gethostbyname that does not 527 understand NIS, so you must have all of your hosts in DNS. 528 529 Some people have reported problems with the SunOS version of 530 -lresolv and/or in.named, and suggest that you get a newer 531 version. The symptoms are delays when you connect to the 532 SMTP server on a SunOS machine or having your domain added to 533 addresses inappropriately. There is a version of BIND 534 version 4.9 on gatekeeper.DEC.COM in pub/BSD/bind/4.9. 535 536 There is substantial disagreement about whether you can make 537 this work with resolv+, which allows you to specify a search-path 538 of services. Some people report that it works fine, others 539 claim it doesn't work at all (including causing sendmail to 540 drop core when it tries to do multiple resolv+ lookups for a 541 single job). I haven't tried resolv+, as we use DNS exclusively. 542 543 Should you want to try resolv+, it is on ftp.uu.net in 544 /networking/ip/dns. 545 546 Apparently getservbyname() can fail under moderate to high 547 load under some circumstances. This will exhibit itself as 548 the message ``554 makeconnection: service "smtp" unknown''. 549 The problem has been traced to one or more blank lines in 550 /etc/services on the NIS server machine. Delete these 551 and it should work. This info is thanks to Brian Bartholomew 552 <bb@math.ufl.edu> of I-Kinetics, Inc. 553 554Solaris 2.x (SunOS 5.x) 555 To compile for Solaris, be sure you use -DSOLARIS. 556 557 To the best of my knowledge, Solaris does not have the 558 gethostbyname problem described above. However, it does 559 have another one: 560 561 From a correspondent: 562 563 For solaris 2.2, I have 564 565 hosts: files dns 566 567 in /etc/nsswitch.conf and /etc/hosts has to have the fully 568 qualified host name. I think "files" has to be before "dns" 569 in /etc/nsswitch.conf during bootup. 570 571 From another correspondent: 572 573 When running sendmail under Solaris, the gethostbyname() 574 hack in conf.c which should perform proper canonicalization 575 of host names could fail. Result: the host name is not 576 canonicalized despite the hack, and you'll have to define $j 577 and $m in sendmail.cf somewhere. 578 579 The reason could be that /etc/nsswitch.conf is improperly 580 configured (at least from sendmail's point of view). For 581 example, the line 582 583 hosts: files nisplus dns 584 585 will make gethostbyname() look in /etc/hosts first, then ask 586 nisplus, then dns. However, if /etc/hosts does not contain 587 the full canonicalized hostname, then no amount of 588 gethostbyname()s will work. 589 590 Solution (or rather, a workaround): Ask nisplus first, then 591 dns, then local files: 592 593 hosts: nisplus dns [NOTFOUND=return] files 594 595 The Solaris "syslog" function is apparently limited to something 596 about 90 characters because of a kernel limitation. If you have 597 source code, you can probably up this number. You can get patches 598 that fix this problem: the patch ids are: 599 600 Solaris 2.1 100834 601 Solaris 2.2 100999 602 Solaris 2.3 101318 603 604 Be sure you have the appropriate patch installed or you won't 605 see system logging. 606 607Ultrix 608 By default, the IDENT protocol is turned off on Ultrix. If you 609 are running Ultrix 4.4 or later, or if you have included patch 610 CXO-8919 for Ultrix 4.2 or 4.3 to fix the TCP problem, you can turn 611 IDENT on in the configuration file by setting the "ident" timeout 612 to 30 seconds. 613 614OSF/1 615 If you are compiling on OSF/1 (DEC Alpha), you must use 616 -L/usr/shlib (otherwise it core dumps on startup). You may also 617 need -mld to get the nlist() function, although some versions 618 apparently don't need this. 619 620 Also, the enclosed makefile removed /usr/sbin/smtpd; if you need 621 it, just create the link to the sendmail binary. 622 623IRIX 624 The header files on SGI IRIX are completely prototyped, and as 625 a result you can sometimes get some warning messages during 626 compilation. These can be ignored. There are two errors in 627 deliver only if you are using gcc, both of the form ``warning: 628 passing arg N of `execve' from incompatible pointer type''. 629 Also, if you compile with -DNIS, you will get a complaint 630 about a declaration of struct dom_binding in a prototype 631 when compiling map.c; this is not important because the 632 function being prototyped is not used in that file. 633 634 In order to compile sendmail you will have had to install 635 the developers' option in order to get the necessary include 636 files. 637 638NeXT 639 If you are compiling on NeXT, you will have to create an empty 640 file "unistd.h" and create a file "dirent.h" containing: 641 642 #include <sys/dir.h> 643 #define dirent direct 644 645 (The Makefile.NeXT should try to do both of these for you.) 646 647 Apparently, there is a bug in getservbyname on Nextstep 3.0 648 that causes it to fail under some circumstances with the 649 message "SYSERR: service "smtp" unknown" logged. You should 650 be able to work around this by including the line: 651 652 OOPort=25 653 654 in your .cf file. 655 656 You may have to use -DNeXT. 657 658BSDI (BSD/386) 1.0, NetBSD 0.9, FreeBSD 1.0 659 The "m4" from BSDI won't handle the config files properly. 660 I haven't had a chance to test this myself. 661 662 The M4 shipped in FreeBSD and NetBSD 0.9 don't handle the config 663 files properly. One must use either GNU m4 1.1 or the PD-M4 664 recently posted in comp.os.386bsd.bugs (and maybe others). 665 NetBSD-current includes the PD-M4 (as stated in the NetBSD file 666 CHANGES). 667 668 FreeBSD 1.0 RELEASE has uname(2) now. Use -DUSEUNAME in order to 669 use it (look into Makefile.FreeBSD). NetBSD-current may have 670 it too but it has not been verified. 671 672 You cannot port the latest version of the Berkeley db library 673 and use it with sendmail without recompiling the world. This 674 is because C library routines use the older version which have 675 incompatible header files -- the result is that it can't read 676 other system files, such as /etc/passwd, unless you use the 677 new db format throughout your system. You should normally just 678 use the version of db supplied in your release. You may need 679 to use -DOLD_NEWDB=1 to make this work -- this turns off some 680 new interface calls (for file locking) that are not in older 681 versions of db. You'll get compile errors if you need this 682 flag and don't have it set. 683 6844.3BSD 685 If you are running a "virgin" version of 4.3BSD, you'll have 686 a very old resolver and be missing some header files. The 687 header files are simple -- create empty versions and everything 688 will work fine. For the resolver you should really port a new 689 version (4.8.3 or later) of the resolver; 4.9 is available on 690 gatekeeper.DEC.COM in pub/BSD/bind/4.9. If you are really 691 determined to continue to use your old, buggy version (or as 692 a shortcut to get sendmail working -- I'm sure you have the 693 best intentions to port a modern version of BIND), you can 694 copy ../contrib/oldbind.compat.c into src and add 695 oldbind.compat.o to OBJADD in the Makefile. 696 697A/UX 698 Date: Tue, 12 Oct 1993 18:28:28 -0400 (EDT) 699 From: "Eric C. Hagberg" <hagberg@med.cornell.edu> 700 Subject: Fix for A/UX ndbm 701 702 I guess this isn't really a sendmail bug, however, it is something 703 that A/UX users should be aware of when compiling sendmail 8.6. 704 705 Apparently, the calls that sendmail is using to the ndbm routines 706 in A/UX 3.0.x contain calls to "broken" routines, in that the 707 aliases database will break when it gets "just a little big" 708 (sorry I don't have exact numbers here, but it broke somewhere 709 around 20-25 aliases for me.), making all aliases non-functional 710 after exceeding this point. 711 712 What I did was to get the gnu-dbm-1.6 package, compile it, and 713 then re-compile sendmail with "-lgdbm", "-DNDBM", and using the 714 ndbm.h header file that comes with the gnu-package. This makes 715 things behave properly. 716 717 I suppose porting the New Berkeley db package is another route, 718 however, I made a quick attempt at it, and found it difficult 719 (not easy at least); the gnu-dbm package "configured" and 720 compiled easily. 721 722SCO Unix 723 From: Thomas Essebier <tom@stallion.oz.au> 724 Organisation: Stallion Technologies Pty Ltd. 725 726 It will probably help those who are trying to configure sendmail 8.6.9 727 to know that if they are on SCO, they had better set 728 OI-dnsrch 729 or they will core dump as soon as they try to use the resolver. 730 ie. although SCO has _res.dnsrch defined, and is kinda BIND 4.8.3, it 731 does not inititialise it, nor does it understand 'search' in 732 /etc/named.boot. 733 - sigh - 734 735DG/UX 736 Doug Anderson <dlander@afterlife.ncsc.mil> has successfully run 737 V8 on the DG/UX 5.4.2 and 5.4R3.x platforms under heavy usage. 738 Originally, the DG /bin/mail program wasn't compatible with 739 the V8 sendmail, since the DG /bin/mail requires the environment 740 variable "_FORCE_MAIL_LOCAL_=yes" be set. Version 8.7 now includes 741 this in the environment before invoking the local mailer. Some 742 have used procmail to avoid this problem in the past. It works 743 but some have experienced file locking problems with their DG/UX 744 ports of procmail. 745 746Apollo DomainOS 747 If you are compiling on Apollo, you will have to create an empty 748 file "unistd.h" and create a file "dirent.h" containing: 749 750 #include <sys/dir.h> 751 #define dirent direct 752 753 (The Makefile.DomainOS will attempt to do both of these for you.) 754 755HP-UX 8.00 756 Date: Mon, 24 Jan 1994 13:25:45 +0200 757 From: Kimmo Suominen <Kimmo.Suominen@lut.fi> 758 Subject: 8.6.5 w/ HP-UX 8.00 on s300 759 760 Just compiled and fought with sendmail 8.6.5 on a HP9000/360 (ie. a 761 series 300 machine) running HP-UX 8.00. 762 763 I was getting segmentation fault when delivering to a local user. 764 With debugging I saw it was faulting when doing _free@libc... *sigh* 765 It seems the new implementation of malloc on s300 is buggy as of 8.0, 766 so I tried out the one in -lmalloc (malloc(3X)). With that it seems 767 to work just dandy. 768 769 When linking, you will get the following error: 770 771 ld: multiply defined symbol _freespace in file /usr/lib/libmalloc.a 772 773 but you can just ignore it. You might want to add this info to the 774 README file for the future... 775 776Linux 777 Something broke between versions 0.99.13 and 0.99.14 of Linux: 778 the flock() system call gives errors. If you are running .14, 779 you must not use flock. You can do this with -DHASFLOCK=0. 780 781 Around the inclusion of bind-4.9.3 & linux libc-4.6.20, the 782 initialization of the _res structure changed. If /etc/hosts.conf 783 was configured as "hosts, bind" the resolver code could return 784 "Name server failure" errors. This is supposedly fixed in 785 later versions of libc (>= 4.6.29?), and later versions of 786 sendmail (> 8.6.10) try to work around the problem. 787 788 Some older versions (< 4.6.20?) of the libc/include files conflict 789 with sendmail's version of cdefs.h. Deleting sendmail's version 790 on those systems should be non-harmful, and new versions don't care. 791 792AIX 793 This version of sendmail does not support MB, MG, and MR resource 794 records, which are supported by AIX sendmail. 795 796RISC/os 797 RISC/os from MIPS is a merged AT&T/Berkeley system. When you 798 compile on that platform you will get duplicate definitions 799 on many files. You can ignore these. 800 801System V Release 4 Based Systems 802 There is a single Makefile that is intended for all SVR4-based 803 systems (called Makefile.SVR4). It defines __svr4__, which is 804 predefined by some compilers. If your compiler already defines 805 this compile variable, you can delete the definition from the 806 Makefile. 807 808 It's been tested on Dell Issue 2.2. 809 810DELL SVR4 811 Date: Mon, 06 Dec 1993 10:42:29 EST 812 From: "Kimmo Suominen" <kim@grendel.lut.fi> 813 Message-ID: <2d0352f9.lento29@lento29.UUCP> 814 To: eric@cs.berkeley.edu 815 Cc: sendmail@cs.berkeley.edu 816 Subject: Notes for DELL SVR4 817 818 Eric, 819 820 Here are some notes for compiling Sendmail 8.6.4 on DELL SVR4. I ran 821 across these things when helping out some people who contacted me by 822 e-mail. 823 824 1) Use gcc 2.4.5 (or later?). Dell distributes gcc 2.1 with their 825 Issue 2.2 Unix. It is too old, and gives you problems with 826 clock.c, because sigset_t won't get defined in <sys/signal.h>. 827 This is due to a problematic protection rule in there, and is 828 fixed with gcc 2.4.5. 829 830 2) If you don't use the new Berkeley DB (-DNEWDB), then you need 831 to add "-lc -lucb" to the libraries to link with. This is because 832 the -ldbm distributed by Dell needs the bcopy, bcmp and bzero 833 functions. It is important that you specify both libraries in 834 the given order to be sure you only get the BSTRING functions 835 from the UCB library (and not the signal routines etc.). 836 837 3) Don't leave out "-lelf" even if compiling with "-lc -lucb". 838 The UCB library also has another copy of the nlist routines, 839 but we do want the ones from "-lelf". 840 841 If anyone needs a compiled gcc 2.4.5 and/or a ported DB library, they 842 can use anonymous ftp to fetch them from lut.fi in the /kim directory. 843 They are copies of what I use on grendel.lut.fi, and offering them 844 does not imply that I would also support them. I have sent the DB 845 port for SVR4 back to Keith Bostic for inclusion in the official 846 distribution, but I haven't heard anything from him as of today. 847 848 - gcc-2.4.5-svr4.tar.gz (gcc 2.4.5 and the corresponding libg++) 849 - db-1.72.tar.gz (with source, objects and a installed copy) 850 851 Cheers 852 + Kim 853 -- 854 * Kimmo.Suominen@lut.fi * SysVr4 enthusiast at GRENDEL.LUT.FI * 855 * KIM@FINFILES.BITNET * Postmaster and Hostmaster at LUT.FI * 856 * + 358 200 865 718 * Unix area moderator at NIC.FUNET.FI * 857 858ConvexOS 10.1 and below 859 In order to use the name server, you must create the file 860 /etc/use_nameserver. If this file does not exist, the call 861 to res_init() will fail and you will have absolutely no 862 access to DNS, including MX records. 863 864Amdahl UTS 2.1.5 865 In order to get UTS to work, you will have to port BIND 4.9. 866 The vendor's BIND is reported to be ``totally inadequate.'' 867 See sendmail/contrib/AmdahlUTS.patch for the patches necessary 868 to get BIND 4.9 compiled for UTS. 869 870UnixWare 2.0 871 According to Alexander Kolbasov <sasha@unitech.gamma.ru>, 872 the m4 on UnixWare 2.0 (still in Beta) will core dump on the 873 config files. GNU m4 and the m4 from UnixWare 1.x both work. 874 875Non-DNS based sites 876 This version of sendmail always tries to connect to the Domain 877 Name System (DNS) to resolve names, regardless of the setting 878 of the `I' option. On most systems that are not running DNS, 879 this will fail quickly and sendmail will continue, but on some 880 systems it has a long timeout. If you have this problem, you 881 will have to recompile without NAMED_BIND. Some people have 882 claimed that they have successfully used "OI+USEVC" to force 883 sendmail to use a virtual circuit -- this will always time out 884 quickly, but also tells sendmail that a failed connection 885 should requeue the message (probably not what you intended). 886 A future release of sendmail will correct this problem. 887 888Both NEWDB and NDBM 889 If you use both -DNDBM and -DNEWDB, you must delete the module 890 ndbm.o from libdb.a and delete the file "ndbm.h" from the files 891 that get installed (that is, use the OLD ndbm.h, not the new 892 ndbm.h). This compatibility module maps ndbm calls into DB 893 calls, and breaks things rather badly. 894 895GNU getopt 896 I'm told that GNU getopt has a problem in that it gets confused 897 by the double call. Use the version in conf.c instead. 898 899BIND 4.9.2 and Ultrix 900 If you are running on Ultrix, be sure you read conf/Info.Ultrix 901 in the BIND distribution very carefully -- there is information 902 in there that you need to know in order to avoid errors of the 903 form: 904 905 /lib/libc.a(gethostent.o): sethostent: multiply defined 906 /lib/libc.a(gethostent.o): endhostent: multiply defined 907 /lib/libc.a(gethostent.o): gethostbyname: multiply defined 908 /lib/libc.a(gethostent.o): gethostbyaddr: multiply defined 909 910 during the link stage. 911 912strtoul 913 Some compilers (notably gcc) claim to be ANSI C but do not 914 include the ANSI-required routine "strtoul". If your compiler 915 has this problem, you will get an error in srvrsmtp.c on the 916 code: 917 918 # ifdef defined(__STDC__) && !defined(BROKEN_ANSI_LIBRARY) 919 e->e_msgsize = strtoul(vp, (char **) NULL, 10); 920 # else 921 e->e_msgsize = strtol(vp, (char **) NULL, 10); 922 # endif 923 924 You can use -DBROKEN_ANSI_LIBRARY to get around this problem. 925 926 927+--------------+ 928| MANUAL PAGES | 929+--------------+ 930 931The manual pages have been written against the -mandoc macros 932instead of the -man macros. The latest version of groff has them 933included. You can also get a copy from FTP.UU.NET in directory 934/systems/unix/bsd-sources/share/tmac. 935 936 937+-----------------+ 938| DEBUGGING HOOKS | 939+-----------------+ 940 941As of 8.6.5, sendmail daemons will catch a SIGUSR1 signal and log 942some debugging output (logged at LOG_DEBUG severity). The 943information dumped is: 944 945 * The value of the $j macro. 946 * A warning if $j is not in the set $=w. 947 * A list of the open file descriptors. 948 * The contents of the connection cache. 949 * If ruleset 89 is defined, it is evaluated and the results printed. 950 951This allows you to get information regarding the runtime state of the 952daemon on the fly. This should not be done too frequently, since 953the process of rewriting may lose memory which will not be recovered. 954Also, ruleset 89 may call non-reentrant routines, so there is a small 955non-zero probability that this will cause other problems. It is 956really only for debugging serious problems. 957 958A typical formulation of ruleset 89 would be: 959 960 R$* $@ $>0 some test address 961 962 963+-----------------------------+ 964| DESCRIPTION OF SOURCE FILES | 965+-----------------------------+ 966 967The following list describes the files in this directory: 968 969Makefile The makefile used here; this version only works with 970 the new Berkeley make. 971Makefile.dist A trimmed down version of the makefile that works with 972 the old make. 973READ_ME This file. 974TRACEFLAGS My own personal list of the trace flags -- not guaranteed 975 to be particularly up to date. 976alias.c Does name aliasing in all forms. 977arpadate.c A subroutine which creates ARPANET standard dates. 978clock.c Routines to implement real-time oriented functions 979 in sendmail -- e.g., timeouts. 980collect.c The routine that actually reads the mail into a temp 981 file. It also does a certain amount of parsing of 982 the header, etc. 983conf.c The configuration file. This contains information 984 that is presumed to be quite static and non- 985 controversial, or code compiled in for efficiency 986 reasons. Most of the configuration is in sendmail.cf. 987conf.h Configuration that must be known everywhere. 988convtime.c A routine to sanely process times. 989daemon.c Routines to implement daemon mode. This version is 990 specifically for Berkeley 4.1 IPC. 991deliver.c Routines to deliver mail. 992domain.c Routines that interface with DNS (the Domain Name 993 System). 994err.c Routines to print error messages. 995envelope.c Routines to manipulate the envelope structure. 996headers.c Routines to process message headers. 997macro.c The macro expander. This is used internally to 998 insert information from the configuration file. 999main.c The main routine to sendmail. This file also 1000 contains some miscellaneous routines. 1001map.c Support for database maps. 1002mci.c Routines that handle mail connection information caching. 1003parseaddr.c The routines which do address parsing. 1004queue.c Routines to implement message queueing. 1005readcf.c The routine that reads the configuration file and 1006 translates it to internal form. 1007recipient.c Routines that manipulate the recipient list. 1008savemail.c Routines which save the letter on processing errors. 1009sendmail.h Main header file for sendmail. 1010srvrsmtp.c Routines to implement server SMTP. 1011stab.c Routines to manage the symbol table. 1012stats.c Routines to collect and post the statistics. 1013sysexits.c List of error messages associated with error codes 1014 in sysexits.h. 1015trace.c The trace package. These routines allow setting and 1016 testing of trace flags with a high granularity. 1017udb.c The user database interface module. 1018usersmtp.c Routines to implement user SMTP. 1019util.c Some general purpose routines used by sendmail. 1020version.c The version number and information about this 1021 version of sendmail. Theoretically, this gets 1022 modified on every change. 1023 1024Eric Allman 1025 1026(Version 8.91, last update 05/25/95 07:55:31) 1027