Copyright (c) 1983, 1986 The Regents of the University of California.
All rights reserved.

Redistribution and use in source and binary forms are permitted
provided that the above copyright notice and this paragraph are
duplicated in all such forms and that any documentation,
advertising materials, and other materials related to such
distribution and use acknowledge that the software was developed
by the University of California, Berkeley. The name of the
University may not be used to endorse or promote products derived
from this software without specific prior written permission.
THIS SOFTWARE IS PROVIDED ``AS IS'' AND WITHOUT ANY EXPRESS OR
IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED
WARRANTIES OF MERCHANTIBILITY AND FITNESS FOR A PARTICULAR PURPOSE.

@(#)syslogd.8 6.6 (Berkeley) 09/19/88

C 5 syslogd - log systems messages /etc/syslogd [ -f configfile ] [ -m markinterval ] [ -d ] Syslogd reads and logs messages into a set of files described by the configuration file /etc/syslog.conf. Each message is one line. A message can contain a priority code, marked by a number in angle braces at the beginning of the line. Priorities are defined in < sys/syslog.h >. Syslogd reads from the UNIX domain socket /dev/log , from an Internet domain socket specified in /etc/services , and from the special device /dev/klog (to read kernel messages).

Syslogd configures when it starts up and whenever it receives a hangup signal. Lines in the configuration file have a selector to determine the message priorities to which the line applies and an action . The action field are separated from the selector by one or more tabs.

Selectors are semicolon separated lists of priority specifiers. Each priority has a facility describing the part of the system that generated the message, a dot, and a level indicating the severity of the message. Symbolic names may be used. An asterisk selects all facilities. All messages of the specified level or higher (greater severity) are selected. More than one facility may be selected using commas to separate them. For example:

*.emerg;mail,daemon.crit

Selects all facilities at the emerg level and the mail and daemon facilities at the crit level.

Known facilities and levels recognized by syslogd are those listed in syslog (3) without the leading ``LOG_''. The additional facility ``mark'' has a message at priority LOG_INFO sent to it every 20 minutes (this may be changed with the -m flag). The ``mark'' facility is not enabled by a facility field containing an asterisk. The level ``none'' may be used to disable a particular facility. For example,

*.debug;mail.none

Sends all messages except mail messages to the selected file.

The second part of each line describes where the message is to be logged if this line is selected. There are four forms:

A filename (beginning with a leading slash). The file will be opened in append mode. A hostname preceeded by an at sign (``@''). Selected messages are forwarded to the syslogd on the named host. A comma separated list of users. Selected messages are written to those users if they are logged in. An asterisk. Selected messages are written to all logged-in users.

Blank lines and lines beginning with `#' are ignored.

For example, the configuration file:

 kern,mark.debug /dev/console
 *.notice;mail.info /usr/spool/adm/syslog
 *.crit /usr/adm/critical
 kern.err @ucbarpa
 *.emerg *
 *.alert eric,kridle
 *.alert;auth.warning ralph

logs all kernel messages and 20 minute marks onto the system console, all notice (or higher) level messages and all mail system messages except debug messages into the file /usr/spool/adm/syslog, and all critical messages into /usr/adm/critical; kernel messages of error severity or higher are forwarded to ucbarpa. All users will be informed of any emergency messages, the users ``eric'' and ``kridle'' will be informed of any alert messages, and the user ``ralph'' will be informed of any alert message, or any warning message (or higher) from the authorization system.

The flags are:

0.5i -f Specify an alternate configuration file.

-m Select the number of minutes between mark messages.

-d Turn on debugging.

Syslogd creates the file /etc/syslog.pid, if possible, containing a single line with its process id. This can be used to kill or reconfigure syslogd.

To bring syslogd down, it should be sent a terminate signal (e.g. kill \`cat /etc/syslog.pid\`).

/etc/syslog.conf the configuration file
/etc/syslog.pid the process id
/dev/log Name of the UNIX domain datagram log socket
/dev/klog The kernel log device

logger(1), syslog(3)