sys: Remove $FreeBSD$: one-line .c pattern

Remove /^[\s*]*__FBSDID\("\$FreeBSD\$"\);?\s*\n/

spdx: The BSD-2-Clause-FreeBSD identifier is obsolete, drop -FreeBSD

The SPDX folks have obsoleted the BSD-2-Clause-FreeBSD identifier. Catch
up to that fact and revert to their recommended match of

spdx: The BSD-2-Clause-FreeBSD identifier is obsolete, drop -FreeBSD

The SPDX folks have obsoleted the BSD-2-Clause-FreeBSD identifier. Catch
up to that fact and revert to their recommended match of BSD-2-Clause.

Discussed with: pfg
MFC After: 3 days
Sponsored by: Netflix

show more ...

sys/dev: further adoption of SPDX licensing ID tags.

Mainly focus on files that use BSD 2-Clause license, however the tool I
was using misidentified many licenses so this was mostly a manual - error

sys/dev: further adoption of SPDX licensing ID tags.

Mainly focus on files that use BSD 2-Clause license, however the tool I
was using misidentified many licenses so this was mostly a manual - error
prone - task.

The Software Package Data Exchange (SPDX) group provides a specification
to make it easier for automated tools to detect and summarize well known
opensource licenses. We are gradually adopting the specification, noting
that the tags are considered only advisory and do not, in any way,
superceed or replace the license texts.

show more ...

cxgb: replace r273280 with a more comprehensive fix.

Poll for link state when the link is down, even for interrupt capable
PHYs.

Allow PHYs to report a dubious "partial" link. If this state is see

cxgb: replace r273280 with a more comprehensive fix.

Poll for link state when the link is down, even for interrupt capable
PHYs.

Allow PHYs to report a dubious "partial" link. If this state is seen 3
consecutive times (each check is ~1s apart) then reset the PHY. This is
a workaround for a situation where repeatedly toggling the link from the
peer gets the AEL2005 PHY into a state where it never establishes a PCS
block lock even when everything is in order.

MFC after: 1 week

show more ...

cxgb(4): reset the PHY if it generates an interrupt for no apparent reason.

MFC after: 1 week

cxgb(4) MFCs: r204271,r204274,r204348,r204921,r205944,r205945,r205946,r205947,r205948,r205949,r205950,r206109

r204271:
Accessing an mbuf after it has been handed off to the hardware is a bad
race as

cxgb(4) MFCs: r204271,r204274,r204348,r204921,r205944,r205945,r205946,r205947,r205948,r205949,r205950,r206109

r204271:
Accessing an mbuf after it has been handed off to the hardware is a bad
race as it could already have been tx'd and freed by that time. Place
the bpf tap just _before_ writing the gen bit.

This fixes a panic when running tcpdump on a cxgb interface.

r204274:
There is no need to test __FreeBSD_version for features that have
been around for a long time now (7.1-ish or even earlier); assume
they are present. These includes MSI, TSO, LRO, VLAN, INTR_FILTERS,
FIRMWARE, etc.

Also, eliminate some dead code and clean up in other places as part
of this quick once-over.

r204348:
Support IFCAP_VLANHWTSO in cxgb(4). It works with or without vlanhwtag.
While here, remove old DPRINTFs and tidy up the capability code a bit.

r204921:
Better TwinAx transceiver detection.

Originally submitted by: <Bruno dot Bittner at isilon dot com>
(This is a rewritten, corrected version of that patch)

r205944:
Refresh the firmware version immediately after it is upgraded (or downgraded).

r205945:
Improved PHY EDC settings.

r205946:
Do not attempt to retrieve interrupt information before it is available.

r205947:
Fix build with "nooptions INET"

r205948:
Fix tx drop statistics.

r205949:
Fix signed/unsigned mix-up that allowed txq->in_use to grow beyond txq->size.

r205950:
Multiple fixes related to queue set sizing and resources:

- Only the tunnelq (TXQ_ETH) requires a buf_ring, an ifq, and the watchdog/timer
callouts. Do not allocate these for the other tx queues.

- Use 16k jumbo clusters only on offload capable cards by default.

- Do not allocate a full tx ring for the offload queue if the card is not
offload capable.

- Slightly better freelist size calculation.

- Fix nmbjumbo4 typo, remove unneeded global variables.

r206109:
Increase response queue size to avoid starvation, add a counter
to track it when it does occur.

show more ...

MFC r199237, r199238, r199239, r199240, r200003

r199237:
sc->rev and is_offload(sc) will always be 0 during probe. Wait till
attach to get correct values.

r199238:
Make sure *some* edc is setup ev

MFC r199237, r199238, r199239, r199240, r200003

r199237:
sc->rev and is_offload(sc) will always be 0 during probe. Wait till
attach to get correct values.

r199238:
Make sure *some* edc is setup even for an unknown transceiver (assume
it is optical).

r199239:
The 10GBASE-T card should use an IPG of 1. Also enable the check
for low power startup on this card.

r199240:
Don't disable the XGMAC's tx on ifconfig down. It is unnecessary
and can cause false backpressure in the chip. Fix a us/ms mixup
while here.

r200003:
T3 firmware 7.8.0 for cxgb(4)

show more ...

MFC r197791

cxgb(4) updates, including:
- support for the new Gen-2, BT, and LP-CR cards.
- T3 firmware 7.7.0
- shared "common code" updates.

Improve cxgb(4)'s behaviour when faced with temporarily "bouncy" links:
- Run the adapter's tick at 1Hz and remove link state checks from it.
Instead, have each port check its link state. Delay th

Improve cxgb(4)'s behaviour when faced with temporarily "bouncy" links:
- Run the adapter's tick at 1Hz and remove link state checks from it.
Instead, have each port check its link state. Delay the check so that
it takes place slightly after the driver is notified of a change in
link state. This is a cheap way to debounce these notifications if
many are received in rapid succession. POLL_LINK_1ST_TIME flag can
also be eliminated as a side effect of these changes.
- Do not reset the PHY when link goes down.
- Clear port's link_fault flag if the PHY indicates link is down.
- get_link_status_r should leave speed and duplex alone when link is down.

MFC after: 1 month

show more ...

Improved PHY EDC settings.

MFC after: 3 days

Better TwinAx transceiver detection.

Originally submitted by: <Bruno dot Bittner at isilon dot com>
(This is a rewritten, corrected version of that patch)

MFC after: 1 week

Make sure *some* edc is setup even for an unknown transceiver (assume
it is optical).

cxgb(4) updates, including:
- support for the new Gen-2, BT, and LP-CR cards.
- T3 firmware 7.7.0
- shared "common code" updates.

Approved by: gnn (mentor)
Obtained from: Chelsio
MFC after: 1 month

Integrate three changes from Chelsio.

1) Add a sysctl that will say what type of PHYs exist on the card.
2) Fix a bug that occurs when an AEL 2005 PHY resets without a transciever
in the card.
3) Un

Integrate three changes from Chelsio.

1) Add a sysctl that will say what type of PHYs exist on the card.
2) Fix a bug that occurs when an AEL 2005 PHY resets without a transciever
in the card.
3) Unify the PHY link detection code.

Obtained from: Navdeep Parhar
MFC after: 10 days

show more ...

Update the Chelsio driver to the latest bits from Chelsio

Firmware upgraded to 7.1.0 (from 5.0.0).
T3C EEPROM and SRAM added; Code to update eeprom/sram fixed.
fl_empty and rx_fifo_ovfl counters can

Update the Chelsio driver to the latest bits from Chelsio

Firmware upgraded to 7.1.0 (from 5.0.0).
T3C EEPROM and SRAM added; Code to update eeprom/sram fixed.
fl_empty and rx_fifo_ovfl counters can be observed via sysctl.
Two new cxgbtool commands to get uP logic analyzer info and uP IOQs
Synced up with Chelsio's "common code" (as of 03/03/09)

Submitted by: Navdeep Parhar at Chelsio
Reviewed by: gnn
MFC after: 2 weeks

show more ...

Check in the actual module recognition code for the Chelsio
driver.

Obtained from: Chelsio Inc.

Fix a bug with the ael1006 PHY. The bug shows up as persistent but incomplete
packet loss, of between 10-30%. The fix is to put the PHY into
and take it out of local loopback mode when resetting the

Fix a bug with the ael1006 PHY. The bug shows up as persistent but incomplete
packet loss, of between 10-30%. The fix is to put the PHY into
and take it out of local loopback mode when resetting the interface.

Obtained from: Chelsio Inc.
MFC after: 3 days

show more ...

Several small additions to the Chelsio 10G driver.

1) Fix a bug in dealing with the Alerus 1006 PHY which prevented the
device from ever coming back up once it had been set to down.

2) Add a kernel

Several small additions to the Chelsio 10G driver.

1) Fix a bug in dealing with the Alerus 1006 PHY which prevented the
device from ever coming back up once it had been set to down.

2) Add a kernel tunable (hw.cxgb.snd_queue_len) which makes it possible
to give the device more than IFQ_MAXLEN entries in its send queue. The
default remains 50.

3) Add code to place the card'd identification and serial number into
its description (%desc) so that users can tell which card they have
installed.

show more ...

Update cxgb include paths to not require prefixing with dev/cxgb

Submitted by: Chelsio Inc.

Vendor fix for PHY problem.

Obtained from: Chelsio Inc.
MFC after: 3 days

import vendor fixes to cxgb

- Integrate 1.133 vendor driver changes
- update some copyrights
- add improved support for delayed ack
- fix issue with fec

- update firmware to 5.0
- add support for T3C
- add DDP support (zero-copy receive)
- fix TOE transmit of large requests
- fix shutdown so that sockets don't remain in CLOSING state indefinitely
- r

- update firmware to 5.0
- add support for T3C
- add DDP support (zero-copy receive)
- fix TOE transmit of large requests
- fix shutdown so that sockets don't remain in CLOSING state indefinitely
- register listeners when an interface is brought up after tom is loaded
- fix setting of multicast filter
- enable link at device attach
- exit tick handler if shutdown is in progress
- add helper for logging TCB
- add sysctls for dumping transmit queues

- note that TOE wxill not be MFC'd until after 7.0 has been finalized

MFC after: 3 days

show more ...

- import new common code for the T304
- update to firmware version 4.1.0

- switch over to standard method for initializing cdevs (contributed by scottl@)
- break out timer_reclaim_task to be per-por

- import new common code for the T304
- update to firmware version 4.1.0

- switch over to standard method for initializing cdevs (contributed by scottl@)
- break out timer_reclaim_task to be per-port
- move msix teardown into separate function
- fix bus_setup_intr for msi-x for the multi-port case so that msi-x resources
are not corrupted on unload
- handle 10/100/1000 base-T media and auto negotiation
- bind qset to cpu even for singleq case
- white space cleanups
- remove recursive PORT_LOCK
- move mtu setting to separate function
- stop and re-init port when changing mtu
- replace all direct references to m_data with calls to mtod
- handle attach failure better by not trying to de-initialize
taskqueues when they have not been allocated
- no longer default to jumbo frames

Sponsored by: Chelsio
MFC after: 3 days

show more ...

When building cxgb as a module make include paths relative to the driver's root.
This will make it possible to build the module out of tree against an older src tree.

MFC after: 3 days