sys: Remove $FreeBSD$: one-line .c comment pattern

Remove /^/[*/]\s*\$FreeBSD\$.*\n/

spdx: The BSD-2-Clause-FreeBSD identifier is obsolete, drop -FreeBSD

The SPDX folks have obsoleted the BSD-2-Clause-FreeBSD identifier. Catch
up to that fact and revert to their recommended match of

spdx: The BSD-2-Clause-FreeBSD identifier is obsolete, drop -FreeBSD

The SPDX folks have obsoleted the BSD-2-Clause-FreeBSD identifier. Catch
up to that fact and revert to their recommended match of BSD-2-Clause.

Discussed with: pfg
MFC After: 3 days
Sponsored by: Netflix

show more ...

Mark inline functions static.

Some code reorganization.

- Remove code duplication by adding two new functions to execute prepared
queue entry via either mbox or request queue and wait for result.
- Since the new function execu

Some code reorganization.

- Remove code duplication by adding two new functions to execute prepared
queue entry via either mbox or request queue and wait for result.
- Since the new function executing via request queue sleeps any way, make
it sleep also in case of overflows or handle shortages. It should make it
more reliable and less affecting other less flexible request queue users.
- Turn isp_target_put_entry() into not target-specific isp_send_entry().
- Make handling of responses with control handles more universal.
- Move RQSTYPE_RPT_ID_ACQ handling into new function.
- Inline isp_handle_other_response(), becoming trivial after above.
- Clean the list of IOCBs from pre-24xx ones.

show more ...

Remove some more dead code from pre-24xx.

Implement request queue overflow protection.

Before this change in case of request queue overflow driver just froze the
device queue for 100ms to retry after. It was pretty bad for performance.
Thi

Implement request queue overflow protection.

Before this change in case of request queue overflow driver just froze the
device queue for 100ms to retry after. It was pretty bad for performance.
This change introduces SIM queue freezing when free space on the request
queue drops below 255 entries (worst case of maximum I/O size S/G list),
checking for a chance to release it on I/O completion. If the queue still
get overflowed somehow, the old mechanism is still in place, just with
delay reduced to 10ms.

With the earlier queue length increase overflows should not happen often,
but it is still easily reachable on synthetic tests.

show more ...

Cleanup DMA handling.

- Make isp_start() to set all the IOCB fields aside of S/G list, removing
extra information from isp_send_cmd(), now only doing S/G lists and sending.
- Turn DMA setup/free f

Cleanup DMA handling.

- Make isp_start() to set all the IOCB fields aside of S/G list, removing
extra information from isp_send_cmd(), now only doing S/G lists and sending.
- Turn DMA setup/free from being card and PCI-specific into OS-specific,
instead add new card-specific method for isp_send_cmd(). Previously this
function was a monster handling all the cards.
- Remove double error code translation.

show more ...

Remove parallel SCSI and 1/2Gb FC support from isp(4).

This removes 288KB (36%) of the driver code and zillions of hacks and
workarounds, making single driver uniformly support several different
gen

Remove parallel SCSI and 1/2Gb FC support from isp(4).

This removes 288KB (36%) of the driver code and zillions of hacks and
workarounds, making single driver uniformly support several different
generations of hardware interfaces, not counting minor card variations.
After years of the hopeless fight, I don't think it worth to continue
support for hardware obsolete for 15-20 years. Instead much cleaner
now code should allow to move forward toward better locking, multiple
queues and other cool features.

All the remaining Qlogic cards starting from 4Gb 24xx to 32Gb 27xx use
the same hardware/firmware interface with minor incremental improvements,
so it seems to be a good new starting point. Except one PCI-X model all
all of them are PCIe and so still usable in modern systems.

Discussed with: ken, scottl, jpaetzel, imp
Relnotes: yes

show more ...

sys/dev: further adoption of SPDX licensing ID tags.

Mainly focus on files that use BSD 2-Clause license, however the tool I
was using misidentified many licenses so this was mostly a manual - error

sys/dev: further adoption of SPDX licensing ID tags.

Mainly focus on files that use BSD 2-Clause license, however the tool I
was using misidentified many licenses so this was mostly a manual - error
prone - task.

The Software Package Data Exchange (SPDX) group provides a specification
to make it easier for automated tools to detect and summarize well known
opensource licenses. We are gradually adopting the specification, noting
that the tags are considered only advisory and do not, in any way,
superceed or replace the license texts.

show more ...

Switch fabric scans from GID_FT to GID_PT+GFF_ID/GFT_ID.

Instead of using GID_FT SNS request to get list of registered FCP ports,
use GID_PT to get list of all Nx_Ports, and then use GFF_ID and/or G

Switch fabric scans from GID_FT to GID_PT+GFF_ID/GFT_ID.

Instead of using GID_FT SNS request to get list of registered FCP ports,
use GID_PT to get list of all Nx_Ports, and then use GFF_ID and/or GFT_ID
requests to find whether they are FCP and target capable.

The problem with old approach is that GID_FT does not report ports without
FC-4 type registered. In particular it was impossible to boot OS from
FreeBSD FC target using QLogic FC BIOS, since one does not register FC-4
type even on new cards and so ignored by old code as incompatible.

As a side bonus this allows initiator to skip pointless logins to other
initiators by fetching that information from SNS instead.

In case some switches do not implement GFF_ID/GFT_ID correctly, add sysctls
to disable that functionality. I handled broken GFF_ID of my Brocade 200E,
but there may be other switches with different bugs.

Linux also uses GID_PT, but GFF_ID is disabled by default there, and GFT_ID
is not supported.

Sponsored by: iXsystems, Inc.

show more ...

Unify initiator and target DMA setup and command sending.

The code is so alike that it is pointless to keep it separate.

MFC after: 2 weeks

Remove dead remnants of SPI target.

MFC after: 2 weeks

Improvements around attach, reset and detach.

This change fixes DMA resource leak on driver unload. Also it removes
DMA resources allocation for hardcoded number of requests before fetching
the rea

Improvements around attach, reset and detach.

This change fixes DMA resource leak on driver unload. Also it removes
DMA resources allocation for hardcoded number of requests before fetching
the real number from firmware. Also it prepares ground for more flexible
IRQs allocation according to firmware capabilities.

MFC after: 2 weeks

show more ...

Register symbolic port/node names in FC name server.

This is cosmetics that simplifies identification of new ports on FC switch.

It would be good to use target name from CTL here instead of hostnam

Register symbolic port/node names in FC name server.

This is cosmetics that simplifies identification of new ports on FC switch.

It would be good to use target name from CTL here instead of hostname, but
it is not passed here through CAM now.

MFC after: 2 weeks

show more ...

Unify handles allocation for initiator and target IOCBs.

I am not sure why this was split long ago, but I see no reason for it.
At this point this unification just slightly reduces memory usage, but

Unify handles allocation for initiator and target IOCBs.

I am not sure why this was split long ago, but I see no reason for it.
At this point this unification just slightly reduces memory usage, but
as next step I plan to reuse shared handle space for other IOCB types.

show more ...

Clear virtual port's port database when disabling it.

Previously it was done only on full chip reinit, that caused old ports
resurrect in case of virtual port reenabling.

Rip off target mode support for parallel SCSI QLogic adapters.

Hacks to enable target mode there complicated code, while didn't really
work. And for outdated hardware fixing it is not really intere

Rip off target mode support for parallel SCSI QLogic adapters.

Hacks to enable target mode there complicated code, while didn't really
work. And for outdated hardware fixing it is not really interesting.

Initiator mode tested with Qlogic 1080 adapter is still working fine.

show more ...

Another round of port scanner rewrite.

This change simplifies and unifies port adding/updating for loop and
fabric scanners. It also fixes problems with scanning restarts due to
concurrent port dat

Another round of port scanner rewrite.

This change simplifies and unifies port adding/updating for loop and
fabric scanners. It also fixes problems with scanning restarts due to
concurrent port databases changes. It also fixes many cosmetic issues.

show more ...

Remove some confusions between loopid and nphdl.

Modern cards in most cases operate abstract port handles, that have no
any relation to real loop IDs. Leave loopid used only where it really
goes ab

Remove some confusions between loopid and nphdl.

Modern cards in most cases operate abstract port handles, that have no
any relation to real loop IDs. Leave loopid used only where it really
goes about local loop IDs.

While there, fix few more cases where LUNs were still printed in decimal.

show more ...

Register our FC4 Features in SNS.

Improve/fix loop scanning routine.

For the most of chips (except anscient ones) port handlers have no relation
to port IDs. In such situation old code scanning first 125 handlers was
quite naive.

Improve/fix loop scanning routine.

For the most of chips (except anscient ones) port handlers have no relation
to port IDs. In such situation old code scanning first 125 handlers was
quite naive. Instead of doing that, send to chip single request to get full
list of port handlers available on specific virtual port and scan only them.

Old code had problems with case of several virtual ports enabled, when port
handlers allocated from global address space could easily go above 125.
This change was successfully tested on 23xx, 24xx and 25xx chips in loop
mode with 4 virtual initiator ports, each seing 50 virtual target ports.

show more ...

Improve INOTs handling for 24xx and above chips.

Unify port database use for target and initiator roles.

Aside from cleaner and more consistent code, this allows ports to be both
target and initiator same time, and easily switch from any role to a

Unify port database use for target and initiator roles.

Aside from cleaner and more consistent code, this allows ports to be both
target and initiator same time, and easily switch from any role to any.

Sponsored by: iXsystems, Inc.

show more ...

-----------
MISC CHANGES

Add a new async event- ISP_TARGET_NOTIFY_ACK, that will guarantee
eventual delivery of a NOTIFY ACK. This is tons better than just
ignoring the return from isp_notify_ack an

-----------
MISC CHANGES

Add a new async event- ISP_TARGET_NOTIFY_ACK, that will guarantee
eventual delivery of a NOTIFY ACK. This is tons better than just
ignoring the return from isp_notify_ack and hoping for the best.

Clean up the lower level lun enable code to be a bit more sensible.

Fix a botch in isp_endcmd which was messing up the sense data.

Fix notify ack for SRR to use a sensible error code in the case
of a reject.

Clean up and make clear what kind of firmware we've loaded and
what capabilities it has.
-----------
FULL (252 byte) SENSE DATA

In CTIOs for the ISP, there's only a limimted amount of space
to load SENSE DATA for associated CHECK CONDITIONS (24 or 26
bytes). This makes it difficult to send full SENSE DATA that can
be up to 252 bytes.

Implement MODE 2 responses which have us build the FCP Response
in system memory which the ISP will put onto the wire directly.

On the initiator side, the same problem occurs in that a command
status response only has a limited amount of space for SENSE DATA.
This data is supplemented by status continuation responses that
the ISP pushes onto the response queue after the status response.
We now pull them all together so that full sense data can be
returned to the periph driver.

This is supported on 23XX, 24XX and 25XX cards.

This is also preparation for doing >16 byte CDBs.

-----------
FC TAPE

Implement full FC-TAPE on both initiator and target mode side. This
capability is driven by firmware loaded, board type, board NVRAM
settings, or hint configuration options to enable or disable. This
is supported for 23XX, 24XX and 25XX cards.

On the initiator side, we pretty much just have to generate a command
reference number for each command we send out. This is FCP-4 compliant
in that we do this per ITL nexus to generate the allowed 1 thru 255
CRN.

In order to support the target side of FC-TAPE, we now pay attention
to more of the PRLI word 3 parameters which will tell us whether
an initiator wants confirmed responses. While we're at it, we'll
pay attention to the initiator view too and report it.

On sending back CTIOs, we will notice whether the initiator wants
confirmed responses and we'll set up flags to do so.

If a response or data frame is lost the initiator sends us an SRR
(Sequence Retransmit Request) ELS which shows up as an SRR notify
and all outstanding CTIOs are nuked with SRR Received status. The
SRR notify contains the offset that the initiator wants us to restart
the data transfer from or to retransmit the response frame.

If the ISP driver still has the CCB around for which the data segment
or response applies, it will retransmit.

However, we typically don't know about a lost data frame until we
send the FCP Response and the initiator totes up counters for data
moved and notices missing segments. In this case we've already
completed the data CCBs already and sent themn back up to the periph
driver. Because there's no really clean mechanism yet in CAM to
handle this, a hack has been put into place to complete the CTIO
CCB with the CAM_MESSAGE_RECV status which will have a MODIFY DATA
POINTER extended message in it. The internal ISP target groks this
and ctl(8) will be modified to deal with this as well.

At any rate, the data is retransmitted and an an FCP response is
sent. The whole point here is to successfully complete a command
so that you don't have to depend on ULP (SCSI) to have to recover,
which in the case of tape is not really possible (hence the name
FC-TAPE).

Sponsored by: Spectralogic
MFC after: 1 month

show more ...

MFC of 204397: fix problems with fast posting handles