sys: Remove $FreeBSD$: one-line .c pattern

Remove /^[\s*]*__FBSDID\("\$FreeBSD\$"\);?\s*\n/

spdx: The BSD-2-Clause-FreeBSD identifier is obsolete, drop -FreeBSD

The SPDX folks have obsoleted the BSD-2-Clause-FreeBSD identifier. Catch
up to that fact and revert to their recommended match of

spdx: The BSD-2-Clause-FreeBSD identifier is obsolete, drop -FreeBSD

The SPDX folks have obsoleted the BSD-2-Clause-FreeBSD identifier. Catch
up to that fact and revert to their recommended match of BSD-2-Clause.

Discussed with: pfg
MFC After: 3 days
Sponsored by: Netflix

show more ...

mps/mpr: Add missing newlines in error messages.

MFC after: 1 week

mps: clean up empty lines in .c and .h files

sys/dev: further adoption of SPDX licensing ID tags.

Mainly focus on files that use BSD 2-Clause license, however the tool I
was using misidentified many licenses so this was mostly a manual - error

sys/dev: further adoption of SPDX licensing ID tags.

Mainly focus on files that use BSD 2-Clause license, however the tool I
was using misidentified many licenses so this was mostly a manual - error
prone - task.

The Software Package Data Exchange (SPDX) group provides a specification
to make it easier for automated tools to detect and summarize well known
opensource licenses. We are gradually adopting the specification, noting
that the tags are considered only advisory and do not, in any way,
superceed or replace the license texts.

show more ...

Changes to make mps(4) and mpr(4) handle reinit with reallocation.

When the mps(4) and mpr(4) drivers need to reinitialize the
firmware, they sometimes need to reallocate all of the memory
allocated

Changes to make mps(4) and mpr(4) handle reinit with reallocation.

When the mps(4) and mpr(4) drivers need to reinitialize the
firmware, they sometimes need to reallocate all of the memory
allocated by the driver. The reallocation happens whenever the IOC
Facts change. That should only happen after a firmware upgrade.

If the reinitialization happens as a result of a timed out command
sent to the card, the command that timed out and triggered the
reinit may have been freed if iocfacts_allocate() reallocated all
memory. If the caller attempts to access the command after that,
the kernel will panic because the caller will be dereferencing
freed memory.

The solution is to set a flag in the softc when we reallocate,
and avoid dereferencing the command strucure if we've reallocated.

The changes are largely the same in both drivers, since mpr(4) is a
derivative of mps(4).

o In iocfacts_allocate(), if the IOC Facts have changed and we
need to reallocate, set the REALLOCATED flag in the softc.

o Change wait_command() to take a struct mps_command ** instead of
a struct mps_command *. This allows us to NULL out the caller's
command pointer if we have to reinit the controller and the data
structures get reallocated. (The REALLOCATED flag will be set
in the softc if that has happened.)

o In every place that calls wait_command(), make sure we handle
the case where the command is NULL after the call.

o The mpr(4) driver has mpr_request_polled() which can also
reinitialize the card. Also check for reallocation there.

Reviewed by: scottl, slm
MFC after: 1 week
Sponsored by: Spectra Logic

show more ...

- No log bit in IOCStatus and endian-safe changes.

Use MPI2_IOCSTATUS_MASK when checking IOCStatus to mask off the log bit, and
make a few more things endian-safe.

- Fix possible use of invalid poi

- No log bit in IOCStatus and endian-safe changes.

Use MPI2_IOCSTATUS_MASK when checking IOCStatus to mask off the log bit, and
make a few more things endian-safe.

- Fix possible use of invalid pointer.

It was possible to use an invalid pointer to get the target ID value. To fix
this, initialize a local Target ID variable to an invalid value and change that
variable to a valid value only if the pointer to the Target ID is not NULL.

- No need to set the MPSSAS_SHUTDOWN flag because it's never used.

- done_ccb pointer can be used if it is NULL.

To prevent this, move check for done_ccb == NULL to before done_ccb is used in
mpssas_stop_unit_done().

- Disks can go missing until a reboot is done in some cases.

This is due to the DevHandle not being released, which causes the Firmware to
not allow that disk to be re-added.

Reviewed by: ken
Approved by: re (gjb), ken, scottl, ambrisko (mentors)
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D6872

show more ...

sys/dev: minor spelling fixes.

Most affect comments, very few have user-visible effects.

Remove mps_request_polled(), it's redundant to mps_wait_command()

Obtained from: Netflix, Inc.

- Updated all files with 2015 Avago copyright, and updated LSI's copyright
dates.

- Changed all of the PCI device strings from LSI to Avago Technologies (LSI).

- Added a sysctl variable to contro

- Updated all files with 2015 Avago copyright, and updated LSI's copyright
dates.

- Changed all of the PCI device strings from LSI to Avago Technologies (LSI).

- Added a sysctl variable to control how StartStopUnit behavior works. User can
select to spin down disks based on if disk is SSD or HDD.

- Inquiry data is required to tell if a disk will support SSU at shutdown or
not. Due to the addition of mpssas_async, which gets Advanced Info but not
Inquiry data, the setting of supports_SSU was moved to the
mpssas_scsiio_complete function, which snoops for any Inquiry commands. And,
since disks are shutdown as a target and not a LUN, this process was
simplified by basing it on targets and not LUNs.

- Added a sysctl variable that sets the amount of time to retry after sending a
failed SATA ID command. This helps with some bad disks and large disks that
require a lot of time to spin up. Part of this change was to add a callout to
handle timeouts with the SATA ID command. The callout function is called
mpssas_ata_id_timeout(). (Fixes PR 191348)

- Changed the way resets work by allowing I/O to continue to devices that are
not currently under a reset condition. This uses devq's instead of simq's and
makes use of the MPSSAS_TARGET_INRESET flag. This change also adds a function
called mpssas_prepare_tm().

- Some changes were made to reduce code duplication when getting a SAS address
for a SATA disk.

- Fixed some formatting and whitespace.

- Bump version of mps driver to 20.00.00.00-fbsd

PR: 191348
Reviewed by: ken, scottl
Approved by: ken, scottl
MFC after: 2 weeks

show more ...

Merge in phase 14+ -> 16 mps driver fixes from LSI:

---------------------------------------------------------------
System panics during a Port reset with ouststanding I/O
--------------------------

Merge in phase 14+ -> 16 mps driver fixes from LSI:

---------------------------------------------------------------
System panics during a Port reset with ouststanding I/O
---------------------------------------------------------------
It is possible to call mps_mapping_free_memory after this
memory is already freed, causing a panic. Removed this extra
call to mps_mappiing_free_memory and call mps_mapping_exit
in place of the mps_mapping_free_memory call so that any
outstanding mapping items can be flushed before memory is
freed.

---------------------------------------------------------------
Correct memory leak during a Port reset with ouststanding I/O
---------------------------------------------------------------
In mps_reinit function, the mapping memory was not being
freed before being re-allocated. Added line to call the
memory free function for mapping memory.

---------------------------------------------------------------
Use CAM_SIM_QUEUED flag in Driver IO path.
---------------------------------------------------------------
This flag informs the XPT that successful abort of a CCB
requires an abort ccb to be issued to the SIM. While
processing SCSI IO's, set the CAM_SIM_QUEUED flag in the
status for the IO. When the command completes, clear this
flag.

---------------------------------------------------------------
Check for CAM_REQ_INPROG in I/O path.
---------------------------------------------------------------
Added a check in mpssas_action_scsiio for the In Progress
status for the IO. If this flag is set, the IO has already
been aborted by the upper layer (before CAM_SIM_QUEUED was
set) and there is no need to send the IO. The request will
be completed without error.

---------------------------------------------------------------
Improve "doorbell handshake method" for mps_get_iocfacts
---------------------------------------------------------------
Removed call to get Port Facts since this information is
not used currently.

Added mps_iocfacts_allocate function to allocate memory
that is based on IOC Facts data. Added mps_iocfacts_free
function to free memory that is based on IOC Facts data.
Both of the functions are used when a Diag Reset is performed
or when the driver is attached/detached. This is needed in
case IOC Facts changes after a Diag Reset, which could
happen if FW is upgraded.

Moved call of mps_bases_static_config_pages from the attach
routine to after the IOC is ready to process accesses based
on the new memory allocations (instead of polling through
the Doorbell).

---------------------------------------------------------------
Set TimeStamp in INIT message in millisecond format Set the IOC
---------------------------------------------------------------

---------------------------------------------------------------
Prefer mps_wait_command to mps_request_polled
---------------------------------------------------------------
Instead of using mps_request_polled, call mps_wait_command
whenever possible. Change the mps_wait_command function to
check the current context and either use interrupt context
or poll if required by using the pause or DELAY function.
Added a check after waiting 50mSecs to see if the command
has timed out. This is only done if polliing, the msleep
command will automatically timeout if the command has taken
too long to complete.

---------------------------------------------------------------
Integrated RAID: Volume Activation Failed error message is
displayed though the volume has been activated.
---------------------------------------------------------------
Instead of failing an IOCTL request that does not have a
large enough buffer to hold the complete reply, copy as
much data from the reply as possible into the user's buffer
and log a message saying that the user's buffer was smaller
than the returned data.

---------------------------------------------------------------
mapping_add_new_device failure due to persistent table FULL
---------------------------------------------------------------
When a new device is added, if it is determined that the
device persistent table is being used and is full, instead
of displaying a message for this condition every time, only
log a message if the MPS_INFO bit is set in the debug_flags.

Submitted by: LSI
MFC after: 1 week

show more ...

Bring in LSI's latest mps(4) 6Gb SAS and WarpDrive driver, version
14.00.00.01-fbsd.

Their description of the changes is as follows:

1. Copyright contents has been changed in all respective .c
and

Bring in LSI's latest mps(4) 6Gb SAS and WarpDrive driver, version
14.00.00.01-fbsd.

Their description of the changes is as follows:

1. Copyright contents has been changed in all respective .c
and .h files

2. Support for WRITE12 and READ12 for direct-io (warpdrive only)
has been added.

3. Driver has added checks to see if Drive has READ_CAP_16
support before sending it down to the device.
If SPC3_SID_PROTECT flag is set in the inquiry data, the
device supports protection information, and must support
the 16 byte read capacity command, otherwise continue without
sending read cap 16. This will optimize driver performance,
since it will not send READ_CAP_16 to the drive which does
not have support of READ_CAP_16.

4. With new approach, "MPTIOCTL_RESET_ADAPTER" IOCTL will not
use DELAY() which is busy loop implementation.
It will use <msleep> (Better way to sleep without busy
loop). Also from the HBA reset code path and some other
places, DELAY() is replaced with msleep() or "pause()",
which is based on sleep/wakeup style calls. Driver use
msleep()/pause() instead of DELAY based on CAN_SLEEP/NO_SLEEP
flags to avoid busy loop which is not required all the
time.e.a

a. While driver is getting loaded, driver calls most of the
commands with NO_SLEEP.
b. When Driver is functional and it needs Reinit of HBA,
CAN_SLEEP flag is used.

5. <mpslsi> driver is not Endian safe. It will not work on Big
Endian machines like Sparc and PowerPC platforms because it
assumes it is running on a Little Endian machine.

Driver code is modified such way that it does not assume CPU
arch is Little Endian.
a. All places where Driver interacts from HBA to Host, it
converts Little Endian format to CPU format.
b. All places where Driver interacts from Host to HBA, it
converts CPU format to Little Endian.

6. Findout memory leaks in FreeBSD Driver and resolve those,
such as memory leak in targ's luns creation/deletion.
Also added additional checks to see memory allocation
success/fail.

7. Add loginfo prints as debug message, i.e. When FW sends any
loginfo, Driver should print those as debug message.
This will help for debugging purpose.

8. There is possibility to get config request timeout. Current
driver is able to detect config request timetout, but it does
not do anything on config_request timeout. Driver should
call mps_reinit() if any request_poll (which is called as
part of config_request) is time out.

9. cdb length check is required for 32 byte CDB. Add correct mpi
control value for 32 bit CDB as below while submitting SCSI IO
Request to controller.
mpi_control |= 4 << MPI2_SCSIIO_CONTROL_ADDCDBLEN_SHIFT;

10. Check the actual status of Message unit reset
(mps_message_unit_reset).Previously FreeBSD Driver just writes
MPI2_FUNCTION_IOC_MESSAGE_UNIT_RESET and never check the ack
(it just wait for 50 millisecond). So, Driver now check the
status of "MPI2_FUNCTION_IOC_MESSAGE_UNIT_RESET" after writing
it to the FW.

Now it also checking for whether doorbell ack uses msleep with
proper sleep flags, instead of <DELAY>.

11. Previously CAM does not detect Multi-Lun Devices. In order to
detect Multi-Lun Devices by CAM the driver needs following change
set:
a. There is "max_lun" field which Driver need to set based on
hw/fw support. Currently LSI released driver does not set
this field.
b. Default of "max_lun" should not be 0 in OS, but it is
currently set to 0 in CAM layer.
c. Export max_lun capacity to 255

12. Driver will not reset target info after port enable complete and
also do Device removal when Device remove from FW. The detail
description is as follows
a. When Driver receive WD PD add events, it will add all
information in driver local data structure.
b. Only for WD, we have below checks after port enable
completes, where driver clear off all information retrieved
at #1.
if ((sc->WD_available &&
(sc->WD_hide_expose == MPS_WD_HIDE_ALWAYS)) ||
(sc->WD_valid_config && (sc->WD_hide_expose ==
MPS_WD_HIDE_IF_VOLUME)) {
// clear off target data structure.
}
It is mainly not to attach PDs to OS.

FreeBSD does bus rescan as older Parallel scsi style. So Driver
needs to handle which Drive is visible to OS. That is a reason
we have to clear off targ information for PDs.

Again, above logic was implemented long time ago. Similar concept
we have for non-wd also. For that, LSI have introduced different
logic to hide PDs.

Eventually, because of above gap, when Phy goes offline, we
observe below failure. That is what Driver is not doing complete
removal of device with FW. (which was pointed by Scott)
Apr 5 02:39:24 Freebsd7 kernel: mpslsi0: mpssas_prepare_remove
Apr 5 02:39:24 Freebsd7 kernel: mpssas_prepare_remove 497 : invalid handle 0xe

Now Driver will not reset target info after port enable complete
and also will do Device removal when Device remove from FW.

13. Returning "CAM_SEL_TIMEOUT" instead of "CAM_TID_INVALID"
error code on request to the Target IDs that have no devices
conected at that moment. As if "CAM_TID_INVALID" error code
is returned to the CAM Layaer then it results in a huge chain
of errors in verbose kernel messages on boot and every
hot-plug event.

Submitted by: Sreekanth Reddy <Sreekanth.Reddy@lsi.com>
MFC after: 3 days

show more ...

Bring in the LSI-supported version of the mps(4) driver.

This involves significant changes to the mps(4) driver, but is not a
complete rewrite.

Some of the changes in this version of the driver:
-

Bring in the LSI-supported version of the mps(4) driver.

This involves significant changes to the mps(4) driver, but is not a
complete rewrite.

Some of the changes in this version of the driver:
- Integrated RAID (IR) support.
- Support for WarpDrive controllers.
- Support for SCSI protection information (EEDP).
- Support for TLR (Transport Level Retries), needed for tape drives.
- Improved error recovery code.
- ioctl interface compatible with LSI utilities.

mps.4: Update the mps(4) driver man page somewhat for the driver
changes. The list of supported hardware still needs to be
updated to reflect the full list of supported cards.

conf/files: Add the new driver files.

mps/mpi/*: Updated version of the MPI header files, with a BSD style
copyright.

mps/*: See above for a description of the new driver features.

modules/mps/Makefile:
Add the new mps(4) driver files.

Submitted by: Kashyap Desai <Kashyap.Desai@lsi.com>
Reviewed by: ken
MFC after: 1 week

show more ...

sys: Remove $FreeBSD$: one-line .c pattern

Remove /^[\s*]*__FBSDID\("\$FreeBSD\$"\);?\s*\n/

spdx: The BSD-2-Clause-FreeBSD identifier is obsolete, drop -FreeBSD

The SPDX folks have obsoleted the BSD-2-Clause-FreeBSD identifier. Catch
up to that fact and revert to their recommended match of

spdx: The BSD-2-Clause-FreeBSD identifier is obsolete, drop -FreeBSD

The SPDX folks have obsoleted the BSD-2-Clause-FreeBSD identifier. Catch
up to that fact and revert to their recommended match of BSD-2-Clause.

Discussed with: pfg
MFC After: 3 days
Sponsored by: Netflix

show more ...

mps/mpr: Add missing newlines in error messages.

MFC after: 1 week

mps: clean up empty lines in .c and .h files

sys/dev: further adoption of SPDX licensing ID tags.

Mainly focus on files that use BSD 2-Clause license, however the tool I
was using misidentified many licenses so this was mostly a manual - error

sys/dev: further adoption of SPDX licensing ID tags.

Mainly focus on files that use BSD 2-Clause license, however the tool I
was using misidentified many licenses so this was mostly a manual - error
prone - task.

The Software Package Data Exchange (SPDX) group provides a specification
to make it easier for automated tools to detect and summarize well known
opensource licenses. We are gradually adopting the specification, noting
that the tags are considered only advisory and do not, in any way,
superceed or replace the license texts.

show more ...

Changes to make mps(4) and mpr(4) handle reinit with reallocation.

When the mps(4) and mpr(4) drivers need to reinitialize the
firmware, they sometimes need to reallocate all of the memory
allocated

Changes to make mps(4) and mpr(4) handle reinit with reallocation.

When the mps(4) and mpr(4) drivers need to reinitialize the
firmware, they sometimes need to reallocate all of the memory
allocated by the driver. The reallocation happens whenever the IOC
Facts change. That should only happen after a firmware upgrade.

If the reinitialization happens as a result of a timed out command
sent to the card, the command that timed out and triggered the
reinit may have been freed if iocfacts_allocate() reallocated all
memory. If the caller attempts to access the command after that,
the kernel will panic because the caller will be dereferencing
freed memory.

The solution is to set a flag in the softc when we reallocate,
and avoid dereferencing the command strucure if we've reallocated.

The changes are largely the same in both drivers, since mpr(4) is a
derivative of mps(4).

o In iocfacts_allocate(), if the IOC Facts have changed and we
need to reallocate, set the REALLOCATED flag in the softc.

o Change wait_command() to take a struct mps_command ** instead of
a struct mps_command *. This allows us to NULL out the caller's
command pointer if we have to reinit the controller and the data
structures get reallocated. (The REALLOCATED flag will be set
in the softc if that has happened.)

o In every place that calls wait_command(), make sure we handle
the case where the command is NULL after the call.

o The mpr(4) driver has mpr_request_polled() which can also
reinitialize the card. Also check for reallocation there.

Reviewed by: scottl, slm
MFC after: 1 week
Sponsored by: Spectra Logic

show more ...

- No log bit in IOCStatus and endian-safe changes.

Use MPI2_IOCSTATUS_MASK when checking IOCStatus to mask off the log bit, and
make a few more things endian-safe.

- Fix possible use of invalid poi

- No log bit in IOCStatus and endian-safe changes.

Use MPI2_IOCSTATUS_MASK when checking IOCStatus to mask off the log bit, and
make a few more things endian-safe.

- Fix possible use of invalid pointer.

It was possible to use an invalid pointer to get the target ID value. To fix
this, initialize a local Target ID variable to an invalid value and change that
variable to a valid value only if the pointer to the Target ID is not NULL.

- No need to set the MPSSAS_SHUTDOWN flag because it's never used.

- done_ccb pointer can be used if it is NULL.

To prevent this, move check for done_ccb == NULL to before done_ccb is used in
mpssas_stop_unit_done().

- Disks can go missing until a reboot is done in some cases.

This is due to the DevHandle not being released, which causes the Firmware to
not allow that disk to be re-added.

Reviewed by: ken
Approved by: re (gjb), ken, scottl, ambrisko (mentors)
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D6872

show more ...

sys/dev: minor spelling fixes.

Most affect comments, very few have user-visible effects.

Remove mps_request_polled(), it's redundant to mps_wait_command()

Obtained from: Netflix, Inc.

- Updated all files with 2015 Avago copyright, and updated LSI's copyright
dates.

- Changed all of the PCI device strings from LSI to Avago Technologies (LSI).

- Added a sysctl variable to contro

- Updated all files with 2015 Avago copyright, and updated LSI's copyright
dates.

- Changed all of the PCI device strings from LSI to Avago Technologies (LSI).

- Added a sysctl variable to control how StartStopUnit behavior works. User can
select to spin down disks based on if disk is SSD or HDD.

- Inquiry data is required to tell if a disk will support SSU at shutdown or
not. Due to the addition of mpssas_async, which gets Advanced Info but not
Inquiry data, the setting of supports_SSU was moved to the
mpssas_scsiio_complete function, which snoops for any Inquiry commands. And,
since disks are shutdown as a target and not a LUN, this process was
simplified by basing it on targets and not LUNs.

- Added a sysctl variable that sets the amount of time to retry after sending a
failed SATA ID command. This helps with some bad disks and large disks that
require a lot of time to spin up. Part of this change was to add a callout to
handle timeouts with the SATA ID command. The callout function is called
mpssas_ata_id_timeout(). (Fixes PR 191348)

- Changed the way resets work by allowing I/O to continue to devices that are
not currently under a reset condition. This uses devq's instead of simq's and
makes use of the MPSSAS_TARGET_INRESET flag. This change also adds a function
called mpssas_prepare_tm().

- Some changes were made to reduce code duplication when getting a SAS address
for a SATA disk.

- Fixed some formatting and whitespace.

- Bump version of mps driver to 20.00.00.00-fbsd

PR: 191348
Reviewed by: ken, scottl
Approved by: ken, scottl
MFC after: 2 weeks

show more ...

Merge in phase 14+ -> 16 mps driver fixes from LSI:

---------------------------------------------------------------
System panics during a Port reset with ouststanding I/O
--------------------------

Merge in phase 14+ -> 16 mps driver fixes from LSI:

---------------------------------------------------------------
System panics during a Port reset with ouststanding I/O
---------------------------------------------------------------
It is possible to call mps_mapping_free_memory after this
memory is already freed, causing a panic. Removed this extra
call to mps_mappiing_free_memory and call mps_mapping_exit
in place of the mps_mapping_free_memory call so that any
outstanding mapping items can be flushed before memory is
freed.

---------------------------------------------------------------
Correct memory leak during a Port reset with ouststanding I/O
---------------------------------------------------------------
In mps_reinit function, the mapping memory was not being
freed before being re-allocated. Added line to call the
memory free function for mapping memory.

---------------------------------------------------------------
Use CAM_SIM_QUEUED flag in Driver IO path.
---------------------------------------------------------------
This flag informs the XPT that successful abort of a CCB
requires an abort ccb to be issued to the SIM. While
processing SCSI IO's, set the CAM_SIM_QUEUED flag in the
status for the IO. When the command completes, clear this
flag.

---------------------------------------------------------------
Check for CAM_REQ_INPROG in I/O path.
---------------------------------------------------------------
Added a check in mpssas_action_scsiio for the In Progress
status for the IO. If this flag is set, the IO has already
been aborted by the upper layer (before CAM_SIM_QUEUED was
set) and there is no need to send the IO. The request will
be completed without error.

---------------------------------------------------------------
Improve "doorbell handshake method" for mps_get_iocfacts
---------------------------------------------------------------
Removed call to get Port Facts since this information is
not used currently.

Added mps_iocfacts_allocate function to allocate memory
that is based on IOC Facts data. Added mps_iocfacts_free
function to free memory that is based on IOC Facts data.
Both of the functions are used when a Diag Reset is performed
or when the driver is attached/detached. This is needed in
case IOC Facts changes after a Diag Reset, which could
happen if FW is upgraded.

Moved call of mps_bases_static_config_pages from the attach
routine to after the IOC is ready to process accesses based
on the new memory allocations (instead of polling through
the Doorbell).

---------------------------------------------------------------
Set TimeStamp in INIT message in millisecond format Set the IOC
---------------------------------------------------------------

---------------------------------------------------------------
Prefer mps_wait_command to mps_request_polled
---------------------------------------------------------------
Instead of using mps_request_polled, call mps_wait_command
whenever possible. Change the mps_wait_command function to
check the current context and either use interrupt context
or poll if required by using the pause or DELAY function.
Added a check after waiting 50mSecs to see if the command
has timed out. This is only done if polliing, the msleep
command will automatically timeout if the command has taken
too long to complete.

---------------------------------------------------------------
Integrated RAID: Volume Activation Failed error message is
displayed though the volume has been activated.
---------------------------------------------------------------
Instead of failing an IOCTL request that does not have a
large enough buffer to hold the complete reply, copy as
much data from the reply as possible into the user's buffer
and log a message saying that the user's buffer was smaller
than the returned data.

---------------------------------------------------------------
mapping_add_new_device failure due to persistent table FULL
---------------------------------------------------------------
When a new device is added, if it is determined that the
device persistent table is being used and is full, instead
of displaying a message for this condition every time, only
log a message if the MPS_INFO bit is set in the debug_flags.

Submitted by: LSI
MFC after: 1 week

show more ...

Bring in LSI's latest mps(4) 6Gb SAS and WarpDrive driver, version
14.00.00.01-fbsd.

Their description of the changes is as follows:

1. Copyright contents has been changed in all respective .c
and

Bring in LSI's latest mps(4) 6Gb SAS and WarpDrive driver, version
14.00.00.01-fbsd.

Their description of the changes is as follows:

1. Copyright contents has been changed in all respective .c
and .h files

2. Support for WRITE12 and READ12 for direct-io (warpdrive only)
has been added.

3. Driver has added checks to see if Drive has READ_CAP_16
support before sending it down to the device.
If SPC3_SID_PROTECT flag is set in the inquiry data, the
device supports protection information, and must support
the 16 byte read capacity command, otherwise continue without
sending read cap 16. This will optimize driver performance,
since it will not send READ_CAP_16 to the drive which does
not have support of READ_CAP_16.

4. With new approach, "MPTIOCTL_RESET_ADAPTER" IOCTL will not
use DELAY() which is busy loop implementation.
It will use <msleep> (Better way to sleep without busy
loop). Also from the HBA reset code path and some other
places, DELAY() is replaced with msleep() or "pause()",
which is based on sleep/wakeup style calls. Driver use
msleep()/pause() instead of DELAY based on CAN_SLEEP/NO_SLEEP
flags to avoid busy loop which is not required all the
time.e.a

a. While driver is getting loaded, driver calls most of the
commands with NO_SLEEP.
b. When Driver is functional and it needs Reinit of HBA,
CAN_SLEEP flag is used.

5. <mpslsi> driver is not Endian safe. It will not work on Big
Endian machines like Sparc and PowerPC platforms because it
assumes it is running on a Little Endian machine.

Driver code is modified such way that it does not assume CPU
arch is Little Endian.
a. All places where Driver interacts from HBA to Host, it
converts Little Endian format to CPU format.
b. All places where Driver interacts from Host to HBA, it
converts CPU format to Little Endian.

6. Findout memory leaks in FreeBSD Driver and resolve those,
such as memory leak in targ's luns creation/deletion.
Also added additional checks to see memory allocation
success/fail.

7. Add loginfo prints as debug message, i.e. When FW sends any
loginfo, Driver should print those as debug message.
This will help for debugging purpose.

8. There is possibility to get config request timeout. Current
driver is able to detect config request timetout, but it does
not do anything on config_request timeout. Driver should
call mps_reinit() if any request_poll (which is called as
part of config_request) is time out.

9. cdb length check is required for 32 byte CDB. Add correct mpi
control value for 32 bit CDB as below while submitting SCSI IO
Request to controller.
mpi_control |= 4 << MPI2_SCSIIO_CONTROL_ADDCDBLEN_SHIFT;

10. Check the actual status of Message unit reset
(mps_message_unit_reset).Previously FreeBSD Driver just writes
MPI2_FUNCTION_IOC_MESSAGE_UNIT_RESET and never check the ack
(it just wait for 50 millisecond). So, Driver now check the
status of "MPI2_FUNCTION_IOC_MESSAGE_UNIT_RESET" after writing
it to the FW.

Now it also checking for whether doorbell ack uses msleep with
proper sleep flags, instead of <DELAY>.

11. Previously CAM does not detect Multi-Lun Devices. In order to
detect Multi-Lun Devices by CAM the driver needs following change
set:
a. There is "max_lun" field which Driver need to set based on
hw/fw support. Currently LSI released driver does not set
this field.
b. Default of "max_lun" should not be 0 in OS, but it is
currently set to 0 in CAM layer.
c. Export max_lun capacity to 255

12. Driver will not reset target info after port enable complete and
also do Device removal when Device remove from FW. The detail
description is as follows
a. When Driver receive WD PD add events, it will add all
information in driver local data structure.
b. Only for WD, we have below checks after port enable
completes, where driver clear off all information retrieved
at #1.
if ((sc->WD_available &&
(sc->WD_hide_expose == MPS_WD_HIDE_ALWAYS)) ||
(sc->WD_valid_config && (sc->WD_hide_expose ==
MPS_WD_HIDE_IF_VOLUME)) {
// clear off target data structure.
}
It is mainly not to attach PDs to OS.

FreeBSD does bus rescan as older Parallel scsi style. So Driver
needs to handle which Drive is visible to OS. That is a reason
we have to clear off targ information for PDs.

Again, above logic was implemented long time ago. Similar concept
we have for non-wd also. For that, LSI have introduced different
logic to hide PDs.

Eventually, because of above gap, when Phy goes offline, we
observe below failure. That is what Driver is not doing complete
removal of device with FW. (which was pointed by Scott)
Apr 5 02:39:24 Freebsd7 kernel: mpslsi0: mpssas_prepare_remove
Apr 5 02:39:24 Freebsd7 kernel: mpssas_prepare_remove 497 : invalid handle 0xe

Now Driver will not reset target info after port enable complete
and also will do Device removal when Device remove from FW.

13. Returning "CAM_SEL_TIMEOUT" instead of "CAM_TID_INVALID"
error code on request to the Target IDs that have no devices
conected at that moment. As if "CAM_TID_INVALID" error code
is returned to the CAM Layaer then it results in a huge chain
of errors in verbose kernel messages on boot and every
hot-plug event.

Submitted by: Sreekanth Reddy <Sreekanth.Reddy@lsi.com>
MFC after: 3 days

show more ...