Compilation failure on ppc and mips due to Revision 342066.
Adding extra memset on chain frame.

Submitted by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed by: Kashyap Desai <Kashyap.Desai@broa

Compilation failure on ppc and mips due to Revision 342066.
Adding extra memset on chain frame.

Submitted by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed by: Kashyap Desai <Kashyap.Desai@broadcom.com>
Approved by: ken
MFC after: 3 days
Sponsored by: Broadcom Inc

show more ...

This patch will add support for NVME PRPs creation by driver for fastpath
capable IOs. NVME specification supports specific type of scatter gather list
called as PRP (Physical Region Page) for IO dat

This patch will add support for NVME PRPs creation by driver for fastpath
capable IOs. NVME specification supports specific type of scatter gather list
called as PRP (Physical Region Page) for IO data buffers. Since NVME drive is
connected behind SAS3.5 tri-mode adapter, MegaRAID driver/firmware has to convert
OS SGLs in native NVMe PRP format. For IOs sent to firmware, MegaRAID firmware
does this job of OS SGLs to PRP translation and send PRPs to backend NVME device.
For fastpath IOs, driver will do this OS SGLs to PRP translation.

Submitted by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed by: Kashyap Desai <Kashyap.Desai@broadcom.com>
Approved by: ken
MFC after: 3 days
Sponsored by: Broadcom Inc

show more ...

To improve RAID 1/10 Write performance, OS drivers need to issue the
required Write IOs as Fast Path IOs (after the appropriate checks
allowing Fast Path to be used) to the appropriate physical drive

To improve RAID 1/10 Write performance, OS drivers need to issue the
required Write IOs as Fast Path IOs (after the appropriate checks
allowing Fast Path to be used) to the appropriate physical drives
(translated from the OS logical IO) and wait for all Write IOs to complete.

Design: A write IO on RAID volume will be examined if it can be sent in
Fast Path based on IO size and starting LBA and ending LBA falling on to
a Physical Drive boundary. If the underlying RAID volume is a RAID 1/10,
driver issues two fast path write IOs one for each corresponding physical
drive after computing the corresponding start LBA for each physical drive.
Both write IOs will have the same payload and are posted to HW such that
replies land in the same reply queue.

If there are no resources available for sending two IOs, driver will send
the original IO from upper layer to RAID volume through the Firmware.

When both IOs are completed by HW, the resources will be released
and SCSI IO completion handler will be called.

Submitted by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed by: Kashyap Desai <Kashyap.Desai@broadcom.com>
Approved by: ken
MFC after: 3 days
Sponsored by: Broadcom Inc

show more ...

Detect sequential Write IOs and pass the hint that it is part of sequential
stream to help HBA Firmware do the Full Stripe Writes. For read IOs on
certain RAID volumes like Read Ahead volumes,this wi

Detect sequential Write IOs and pass the hint that it is part of sequential
stream to help HBA Firmware do the Full Stripe Writes. For read IOs on
certain RAID volumes like Read Ahead volumes,this will help driver to
send it to Firmware even if the IOs can potentially be sent to
hardware directly (called fast path) bypassing firmware.

Design: 8 streams are maintained per RAID volume as per the combined
firmware/driver design. When there is no stream detected the LRU stream
is used for next potential stream and LRU/MRU map is updated to make this
as MRU stream. Every time a stream is detected the MRU map
is updated to make the current stream as MRU stream.

Submitted by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed by: Kashyap Desai <Kashyap.Desai@broadcom.com>
Approved by: ken
MFC after: 3 days
Sponsored by: Broadcom Inc

show more ...

This patch will add new interface to support more than 256 JBODs.

Submitted by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed by: Kashyap Desai <Kashyap.Desai@broadcom.com>
Approved by: ken
MF

This patch will add new interface to support more than 256 JBODs.

Submitted by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed by: Kashyap Desai <Kashyap.Desai@broadcom.com>
Approved by: ken
MFC after: 3 days
Sponsored by: Broadcom Inc

show more ...

This patch will add support for divert bitmap in RAID map. Divert bitmap is supported for
SAS3.5 adapters only.

Submitted by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed by: Kashyap Desai <Ka

This patch will add support for divert bitmap in RAID map. Divert bitmap is supported for
SAS3.5 adapters only.

Submitted by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed by: Kashyap Desai <Kashyap.Desai@broadcom.com>
Approved by: ken
MFC after: 3 days
Sponsored by: Broadcom Inc

show more ...

This patch will add support for next generation(SAS3.5) of Tri mode(SAS, SATA, NVMe)
MegaRAID adapters.

Submitted by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed by: Kashyap Desai <Kashyap.De

This patch will add support for next generation(SAS3.5) of Tri mode(SAS, SATA, NVMe)
MegaRAID adapters.

Submitted by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed by: Kashyap Desai <Kashyap.Desai@broadcom.com>
Approved by: ken
MFC after: 3 days
Sponsored by: Broadcom Inc

show more ...

mrsas(4): Remove unneed extra arg from MR_LdBlockSizeGet().

Obtained From: DragonFly (482292f9859e1ceae4f35343c0a8eac4c4486d1)

Always null-terminate ccb_pathinq.(sim_vid|hba_vid|dev_name)

The sim_vid, hba_vid, and dev_name fields of struct ccb_pathinq are
fixed-length strings. AFAICT the only place they're read is in
sbin/c

Always null-terminate ccb_pathinq.(sim_vid|hba_vid|dev_name)

The sim_vid, hba_vid, and dev_name fields of struct ccb_pathinq are
fixed-length strings. AFAICT the only place they're read is in
sbin/camcontrol/camcontrol.c, which assumes they'll be null-terminated.
However, the kernel doesn't null-terminate them. A bunch of copy-pasted code
uses strncpy to write them, and doesn't guarantee null-termination. For at
least 4 drivers (mpr, mps, ciss, and hyperv), the hba_vid field actually
overflows. You can see the result by doing "camcontrol negotiate da0 -v".

This change null-terminates those fields everywhere they're set in the
kernel. It also shortens a few strings to ensure they'll fit within the
16-character field.

PR: 215474
Reported by: Coverity
CID: 1009997 1010000 1010001 1010002 1010003 1010004 1010005
CID: 1331519 1010006 1215097 1010007 1288967 1010008 1306000
CID: 1211924 1010009 1010010 1010011 1010012 1010013 1010014
CID: 1147190 1010017 1010016 1010018 1216435 1010020 1010021
CID: 1010022 1009666 1018185 1010023 1010025 1010026 1010027
CID: 1010028 1010029 1010030 1010031 1010033 1018186 1018187
CID: 1010035 1010036 1010042 1010041 1010040 1010039
Reviewed by: imp, sephe, slm
MFC after: 4 weeks
Sponsored by: Spectra Logic Corp
Differential Revision: https://reviews.freebsd.org/D9037
Differential Revision: https://reviews.freebsd.org/D9038

show more ...

This patch will unblock SYNCHRONIZE_CACHE command to firmware, i.e. don't block the SYNCHRONIZE_CACHE command at driver instead of
passing it to firmware for all Gen3 controllers.
For Thunderbolt con

This patch will unblock SYNCHRONIZE_CACHE command to firmware, i.e. don't block the SYNCHRONIZE_CACHE command at driver instead of
passing it to firmware for all Gen3 controllers.
For Thunderbolt controller, keep the legacy behavior i.e. return the SYNCHRONIZE_CACHE command with success status from driver itself.

There is Sysctl parameter 'block_sync_cache' is provided to enable customers either to block/unblock these commands to facilitate
legacy behavior if there is a compatibility issue. Default value for module parameter is to unblock this command.

Submitted by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed by: Kashyap Desai <Kashyap.Desai@broadcom.com>
MFC after: 3 days
Sponsored by: Broadcom Limited/AVAGO Technologies

show more ...

This patch will add task management support in driver. Below is high level description:
If a SCSI IO times out, then before initiating OCR, now the driver will try to send a
target reset to the parti

This patch will add task management support in driver. Below is high level description:
If a SCSI IO times out, then before initiating OCR, now the driver will try to send a
target reset to the particular target for which the IO is timed out. If that also fails,
then the driver will initiate OCR.

Submitted by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed by: Kashyap Desai <Kashyap.Desai@broadcom.com>
MFC after: 3 days
Sponsored by: Broadcom Limited/AVAGO Technologies

show more ...

Add sanity check in IO and IOCTL path not to process command further if controller is in
HW_CRITICAL_ERROR.

Submitted by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed by: Kashyap Desai <Ka

Add sanity check in IO and IOCTL path not to process command further if controller is in
HW_CRITICAL_ERROR.

Submitted by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed by: Kashyap Desai <Kashyap.Desai@broadcom.com>
MFC after: 3 days
Sponsored by: Broadcom Limited/AVAGO Technologies

show more ...

Use a variable to indicate Gen3 controllers and remove all PCI ids based
checks used for gen3 controllers.

Submitted by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed by: Kashyap Desai <Kas

Use a variable to indicate Gen3 controllers and remove all PCI ids based
checks used for gen3 controllers.

Submitted by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed by: Kashyap Desai <Kashyap.Desai@broadcom.com>
MFC after: 3 days
Sponsored by: Broadcom Limited/AVAGO Technologies

show more ...

Problem statement:
MFI linked list in megaraid_sas driver is used for mfi-mpt pass-through commands.
This list can be corrupted due to many possible race conditions in driver and
eventually we may se

Problem statement:
MFI linked list in megaraid_sas driver is used for mfi-mpt pass-through commands.
This list can be corrupted due to many possible race conditions in driver and
eventually we may see kernel panic.

One example -
MFI frame is freed from calling process as driver send command via polling method and interrupt
for that command comes after driver free mfi frame (actually even after some other context reuse
the mfi frame). When driver receive MPT frame in ISR, driver will be using the index of MFI and
access that MFI frame and finally in-used MFI frames list will be corrupted.

High level description of new solution -
Free MFI and MPT command from same context.
Free both the command either from process (from where mfi-mpt pass-through was called) or from
ISR context. Do not split freeing of MFI and MPT, because it creates the race condition which
will do MFI/MPT list.

Submitted by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed by: Kashyap Desai <Kashyap.Desai@broadcom.com>
MFC after: 3 days
Sponsored by: Broadcom Limited/AVAGO Technologies

show more ...

Added support for Avago/Broadcom Cutlass(12 Gbps- 16 port count) controllers.

Submitted by: Sumit Saxena <Sumit.Saxena@broadcom.com>
Reviewed by: Kashyap Desai <Kashyap.Desai@broadcom.com>
MFC

Added support for Avago/Broadcom Cutlass(12 Gbps- 16 port count) controllers.

Submitted by: Sumit Saxena <Sumit.Saxena@broadcom.com>
Reviewed by: Kashyap Desai <Kashyap.Desai@broadcom.com>
MFC after: 3 days
Sponsored by: AVAGO/BROADCOM Limited

show more ...

Following bugs fixed as part of this patch:
.Kernel panic while collecting kdump (reported by Doug A.)
.NULL pointer dereference at sertain places
.Removed dead codes

Submitted by: Sumit Saxena <s

Following bugs fixed as part of this patch:
.Kernel panic while collecting kdump (reported by Doug A.)
.NULL pointer dereference at sertain places
.Removed dead codes

Submitted by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed by: Kashyap Desai <Kashyap.Desai@broadcom.com>
MFC after: 3 days
Sponsored by: AVAGO Technologies

show more ...

Added supprot for Avago Intruder controller.

Submitted by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed by: Kashyap Desai <Kashyap.Desai@broadcom.com>
MFC after: 3 days
Sponsored by: AV

Added supprot for Avago Intruder controller.

Submitted by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed by: Kashyap Desai <Kashyap.Desai@broadcom.com>
MFC after: 3 days
Sponsored by: AVAGO Technologies

show more ...

This patch implements driver support for 1MB IO size.

NOTE:
The FreeBSD system currently restricts the MAX IO size to MAXPHYS which
in turn is 128KB. We tested the 1MB IO by converting the MAXPHYS t

This patch implements driver support for 1MB IO size.

NOTE:
The FreeBSD system currently restricts the MAX IO size to MAXPHYS which
in turn is 128KB. We tested the 1MB IO by converting the MAXPHYS to 1MB.

Following is the mail reference:
http://lists.freebsd.org/pipermail/freebsd-scsi/2015-January/006568.html

Submitted by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed by: Kashyap Desai <Kashyap.Desai@broadcom.com>
MFC after: 3 days
Sponsored by: AVAGO Technologies

show more ...

Similar to RAID map for Logical Drives, now JBOD map has been introduced for
JBODs. Driver has to sync the JBOD map with firmware and use sequence number
as a reference for JBOD FastPath I/O's.

Subm

Similar to RAID map for Logical Drives, now JBOD map has been introduced for
JBODs. Driver has to sync the JBOD map with firmware and use sequence number
as a reference for JBOD FastPath I/O's.

Submitted by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed by: Kashyap Desai <Kashyap.Desai@broadcom.com>
MFC after: 3 days
Sponsored by: AVAGO Technologies

show more ...

There was no ERROR handling for firmware command TIMEOUT. This patch
takes care of any firmware command timeout scenarios by initiating OCR.

Submitted by: Sumit Saxena <sumit.saxena@broadcom.com>

There was no ERROR handling for firmware command TIMEOUT. This patch
takes care of any firmware command timeout scenarios by initiating OCR.

Submitted by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed by: Kashyap Desai <Kashyap.Desai@broadcom.com>
MFC after: 3 days
Sponsored by: AVAGO Technologies

show more ...

sys/dev: minor spelling fixes.

Most affect comments, very few have user-visible effects.

Corrected indentation on conflicted source files.

Reviewed by: ambrisko
MFC after: 2 weeks
Sponsored by: AVAGO Technologies

Configured the mrsas(4) driver to support UNMAPPED I/O and updated driver version.

Reviewed by: ambrisko
MFC after: 2 weeks
Sponsored by: AVAGO Technologies

1. All LSI namings are converted to AVAGO Tech.
2. Fix in AEN path(suggested by John Baldwin).
3. Fix IOCTL path w.r.t Sense key handling

Reviewed by: ambrisko
MFC after: 2 weeks
Sponsored by: AVAGO

1. All LSI namings are converted to AVAGO Tech.
2. Fix in AEN path(suggested by John Baldwin).
3. Fix IOCTL path w.r.t Sense key handling

Reviewed by: ambrisko
MFC after: 2 weeks
Sponsored by: AVAGO Technologies

show more ...

Current driver does fast path read load balancing between arm and mirror disk
for two Drive Raid-1 configuration only.

Now, Driver support fast path read load balancing for all (any number of disk)

Current driver does fast path read load balancing between arm and mirror disk
for two Drive Raid-1 configuration only.

Now, Driver support fast path read load balancing for all (any number of disk) Raid-1 configuration.

Reviewed by: ambrisko
MFC after: 2 weeks
Sponsored by: AVAGO Technologies

show more ...