net: ti: icssg_prueth: Fix NULL pointer dereference in prueth_probe()

In the prueth_probe() function, if one of the calls to emac_phy_connect()
fails due to of_phy_connect() returning NULL, then the

net: ti: icssg_prueth: Fix NULL pointer dereference in prueth_probe()

In the prueth_probe() function, if one of the calls to emac_phy_connect()
fails due to of_phy_connect() returning NULL, then the subsequent call to
phy_attached_info() will dereference a NULL pointer.

Check the return code of emac_phy_connect and fail cleanly if there is an
error.

Fixes: 128d5874c082 ("net: ti: icssg-prueth: Add ICSSG ethernet driver")
Cc: stable@vger.kernel.org
Signed-off-by: Romain Gantois <romain.gantois@bootlin.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: MD Danish Anwar <danishanwar@ti.com>
Link: https://lore.kernel.org/r/20240521-icssg-prueth-fix-v1-1-b4b17b1433e9@bootlin.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

show more ...

net: ti: icssg_prueth: Add SW TX / RX Coalescing based on hrtimers

Add SW IRQ coalescing based on hrtimers for RX and TX data path for ICSSG
driver, which can be enabled by ethtool commands:

- RX c

net: ti: icssg_prueth: Add SW TX / RX Coalescing based on hrtimers

Add SW IRQ coalescing based on hrtimers for RX and TX data path for ICSSG
driver, which can be enabled by ethtool commands:

- RX coalescing
ethtool -C eth1 rx-usecs 50

- TX coalescing can be enabled per TX queue

- by default enables coalescing for TX0
ethtool -C eth1 tx-usecs 50
- configure TX0
ethtool -Q eth0 queue_mask 1 --coalesce tx-usecs 100
- configure TX1
ethtool -Q eth0 queue_mask 2 --coalesce tx-usecs 100
- configure TX0 and TX1
ethtool -Q eth0 queue_mask 3 --coalesce tx-usecs 100 --coalesce
tx-usecs 100

Minimum value for both rx-usecs and tx-usecs is 20us.

Compared to gro_flush_timeout and napi_defer_hard_irqs this patch allows
to enable IRQ coalescing for RX path separately.

Benchmarking numbers:
===============================================================
| Method | Tput_TX | CPU_TX | Tput_RX | CPU_RX |
| ==============================================================
| Default Driver 943 Mbps 31% 517 Mbps 38% |
| IRQ Coalescing (Patch) 943 Mbps 28% 518 Mbps 25% |
===============================================================

Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240430120634.1558998-1-danishanwar@ti.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

show more ...

net: ti: icssg-prueth: Modify common functions for SR1.0

Some parts of the logic differ only slightly between Silicon Revisions.
In these cases add the bits that differ to a common function that
exe

net: ti: icssg-prueth: Modify common functions for SR1.0

Some parts of the logic differ only slightly between Silicon Revisions.
In these cases add the bits that differ to a common function that
executes those bits conditionally based on the Silicon Revision.

Based on the work of Roger Quadros, Vignesh Raghavendra and
Grygorii Strashko in TI's 5.10 SDK [1].

[1]: https://git.ti.com/cgit/ti-linux-kernel/ti-linux-kernel/tree/?h=ti-linux-5.10.y

Co-developed-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Diogo Ivo <diogo.ivo@siemens.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: MD Danish Anwar <danishanwar@ti.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

show more ...

net: ti: icssg-prueth: Add functions to configure SR1.0 packet classifier

Add the functions to configure the SR1.0 packet classifier.

Based on the work of Roger Quadros in TI's 5.10 SDK [1].

[1]:

net: ti: icssg-prueth: Add functions to configure SR1.0 packet classifier

Add the functions to configure the SR1.0 packet classifier.

Based on the work of Roger Quadros in TI's 5.10 SDK [1].

[1]: https://git.ti.com/cgit/ti-linux-kernel/ti-linux-kernel/tree/?h=ti-linux-5.10.y

Co-developed-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Diogo Ivo <diogo.ivo@siemens.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: MD Danish Anwar <danishanwar@ti.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

show more ...

net: ti: icssg-prueth: Move common functions into a separate file

In order to allow code sharing between Silicon Revisions 1.0 and 2.0
move all functions that can be shared into a common file. This

net: ti: icssg-prueth: Move common functions into a separate file

In order to allow code sharing between Silicon Revisions 1.0 and 2.0
move all functions that can be shared into a common file. This commit
introduces no functional changes.

Signed-off-by: Diogo Ivo <diogo.ivo@siemens.com>
Reviewed-by: MD Danish Anwar <danishanwar@ti.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

show more ...

net: ti: icssg-prueth: Remove duplicate cleanup calls in emac_ndo_stop()

Remove the duplicate calls to prueth_emac_stop() and
prueth_cleanup_tx_chns() in emac_ndo_stop().

Signed-off-by: Diogo Ivo <

net: ti: icssg-prueth: Remove duplicate cleanup calls in emac_ndo_stop()

Remove the duplicate calls to prueth_emac_stop() and
prueth_cleanup_tx_chns() in emac_ndo_stop().

Signed-off-by: Diogo Ivo <diogo.ivo@siemens.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: MD Danish Anwar <danishanwar@ti.com>
Reviewed-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: ti: icssg-prueth: Fix error cleanup on failing pruss_request_mem_region

We were just continuing in this case, surely not desired.

Fixes: 128d5874c082 ("net: ti: icssg-prueth: Add ICSSG etherne

net: ti: icssg-prueth: Fix error cleanup on failing pruss_request_mem_region

We were just continuing in this case, surely not desired.

Fixes: 128d5874c082 ("net: ti: icssg-prueth: Add ICSSG ethernet driver")
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: ti: icssg-prueth: Add missing icss_iep_put to error path

Analogously to prueth_remove, just also taking care for NULL'ing the
iep pointers.

Fixes: 186734c15886 ("net: ti: icssg-prueth: add pac

net: ti: icssg-prueth: Add missing icss_iep_put to error path

Analogously to prueth_remove, just also taking care for NULL'ing the
iep pointers.

Fixes: 186734c15886 ("net: ti: icssg-prueth: add packet timestamping and ptp support")
Fixes: 443a2367ba3c ("net: ti: icssg-prueth: am65x SR2.0 add 10M full duplex support")
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Reviewed-by: MD Danish Anwar <danishanwar@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: ti: icssg-prueth: Add phys_port_name support

Helps identifying the ports in udev rules e.g.

Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.c

net: ti: icssg-prueth: Add phys_port_name support

Helps identifying the ports in udev rules e.g.

Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/895ae9c1-b6dd-4a97-be14-6f2b73c7b2b5@siemens.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

show more ...

net: ethernet: Use device_get_match_data()

Use preferred device_get_match_data() instead of of_match_device() to
get the driver match data. With this, adjust the includes to explicitly
include the c

net: ethernet: Use device_get_match_data()

Use preferred device_get_match_data() instead of of_match_device() to
get the driver match data. With this, adjust the includes to explicitly
include the correct headers.

Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

dmaengine: ti: k3-udma-glue: clean up k3_udma_glue_tx_get_irq() return

The k3_udma_glue_tx_get_irq() function currently returns negative error
codes on error, zero on error and positive values for s

dmaengine: ti: k3-udma-glue: clean up k3_udma_glue_tx_get_irq() return

The k3_udma_glue_tx_get_irq() function currently returns negative error
codes on error, zero on error and positive values for success. This
complicates life for the callers who need to propagate the error code.
Also GCC will not warn about unsigned comparisons when you check:

if (unsigned_irq <= 0)

All the callers have been fixed now but let's just make this easy going
forward.

Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Acked-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: ti: icssg-prueth: Fix signedness bug in prueth_init_tx_chns()

The "tx_chn->irq" variable is unsigned so the error checking does not
work correctly.

Fixes: 128d5874c082 ("net: ti: icssg-prueth:

net: ti: icssg-prueth: Fix signedness bug in prueth_init_tx_chns()

The "tx_chn->irq" variable is unsigned so the error checking does not
work correctly.

Fixes: 128d5874c082 ("net: ti: icssg-prueth: Add ICSSG ethernet driver")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: ti: icssg-prueth: Add support for half duplex operation

This patch adds support for half duplex operation at 10M and 100M link
speeds for AM654x/AM64x devices.
- Driver configures rand_seed, a

net: ti: icssg-prueth: Add support for half duplex operation

This patch adds support for half duplex operation at 10M and 100M link
speeds for AM654x/AM64x devices.
- Driver configures rand_seed, a random number, in DMEM HD_RAND_SEED_OFFSET
field, which will be used by firmware for Back off time calculation.
- Driver informs FW about half duplex link operation in DMEM
PORT_LINK_SPEED_OFFSET field by setting bit 7 for 10/100M HD.

Hence, the half duplex operation depends on board design the
"ti,half-duplex-capable" property has to be enabled for ICSS-G ports if HW
is capable to perform half duplex.

Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: ti: icssg-prueth: Add AM64x icssg support

Add AM64x ICSSG support which is similar to am65x SR2.0, but required:
- all ring configured in exposed ring mode
- always fill both original and buffe

net: ti: icssg-prueth: Add AM64x icssg support

Add AM64x ICSSG support which is similar to am65x SR2.0, but required:
- all ring configured in exposed ring mode
- always fill both original and buffer fields in cppi5 desc

Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

show more ...

net: ti: icssg-prueth: am65x SR2.0 add 10M full duplex support

For AM65x SR2.0 it's required to enable IEP1 in raw 64bit mode which is
used by PRU FW to monitor the link and apply w/a for 10M link i

net: ti: icssg-prueth: am65x SR2.0 add 10M full duplex support

For AM65x SR2.0 it's required to enable IEP1 in raw 64bit mode which is
used by PRU FW to monitor the link and apply w/a for 10M link issue.
Note. No public errata available yet.

Without this w/a the PRU FW will stuck if link state changes under TX
traffic pressure.

Hence, add support for 10M full duplex for AM65x SR2.0:
- add new IEP API to enable IEP, but without PTP support
- add pdata quirk_10m_link_issue to enable 10M link issue w/a.

Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: ti: icssg-prueth: add packet timestamping and ptp support

Add packet timestamping TS and PTP PHC clock support.

For AM65x and AM64x:
- IEP1 is not used
- IEP0 is configured in shadow mode wi

net: ti: icssg-prueth: add packet timestamping and ptp support

Add packet timestamping TS and PTP PHC clock support.

For AM65x and AM64x:
- IEP1 is not used
- IEP0 is configured in shadow mode with 1ms cycle and shared between
Linux and FW. It provides time and TS in number cycles, so special
conversation in ns is required.
- IEP0 shared between PRUeth ports.
- IEP0 supports PPS, periodic output.
- IEP0 settime() and enabling PPS required FW interraction.
- RX TS provided with each packet in CPPI5 descriptor.
- TX TS returned through separate ICSSG hw queues for each port. TX TS
readiness is signaled by INTC IRQ. Only one packet at time can be requested
for TX TS.

Signed-off-by: Roger Quadros <rogerq@ti.com>
Co-developed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: ti: icssg-prueth: Add Power management support

Add suspend / resume APIs to support power management in ICSSG ethernet
driver.

Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: MD Danis

net: ti: icssg-prueth: Add Power management support

Add suspend / resume APIs to support power management in ICSSG ethernet
driver.

Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: ti: icssg-prueth: Add ethtool ops for ICSSG Ethernet driver

Add icssg_ethtool.c file. This file will be used for dumping statistics
via ethtool for ICSSG ethernet driver.

Reviewed-by: Andrew L

net: ti: icssg-prueth: Add ethtool ops for ICSSG Ethernet driver

Add icssg_ethtool.c file. This file will be used for dumping statistics
via ethtool for ICSSG ethernet driver.

Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: ti: icssg-prueth: Add Standard network staticstics

Implement .ndo_get_stats64 to dump standard network interface
statistics for ICSSG ethernet driver.

Signed-off-by: MD Danish Anwar <danishanw

net: ti: icssg-prueth: Add Standard network staticstics

Implement .ndo_get_stats64 to dump standard network interface
statistics for ICSSG ethernet driver.

Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: ti: icssg-prueth: Add ICSSG Stats

Add icssg_stats.c to help dump, icssg related driver statistics.

ICSSG has hardware registers for providing statistics like total rx bytes,
total tx bytes, et

net: ti: icssg-prueth: Add ICSSG Stats

Add icssg_stats.c to help dump, icssg related driver statistics.

ICSSG has hardware registers for providing statistics like total rx bytes,
total tx bytes, etc. These registers are of 32 bits and hence in case of 1G
link, they overflows in around 32 seconds. The behaviour of these registers
is such that they don't roll back to 0 after overflow but rather stay at
UINT_MAX.

These registers support a feature where the value written to them is
subtracted from the register. This feature can be utilized to fix the
overflowing of stats.

This solution uses a Workqueues based solution where a function gets
called before the registers overflow (every 25 seconds in 1G link, 25000
seconds in 100M link), this function saves the register
values in local variables and writes the last read value to the
register. So any update during the read will be taken care of.

Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: ti: icssg-prueth: Add ICSSG ethernet driver

This is the Ethernet driver for TI AM654 Silicon rev. 2
with the ICSSG PRU Sub-system running dual-EMAC firmware.

The Programmable Real-time Unit an

net: ti: icssg-prueth: Add ICSSG ethernet driver

This is the Ethernet driver for TI AM654 Silicon rev. 2
with the ICSSG PRU Sub-system running dual-EMAC firmware.

The Programmable Real-time Unit and Industrial Communication Subsystem
Gigabit (PRU_ICSSG) is a low-latency microcontroller subsystem in the TI
SoCs. This subsystem is provided for the use cases like implementation of
custom peripheral interfaces, offloading of tasks from the other
processor cores of the SoC, etc.

Every ICSSG core has two Programmable Real-Time Unit(PRUs),
two auxiliary Real-Time Transfer Unit (RT_PRUs), and
two Transmit Real-Time Transfer Units (TX_PRUs). Each one of these runs
its own firmware. Every ICSSG core has two MII ports connect to these
PRUs and also a MDIO port.

The cores can run different firmwares to support different protocols and
features like switch-dev, timestamping, etc.

It uses System DMA to transfer and receive packets and
shared memory register emulation between the firmware and
driver for control and configuration.

This patch adds support for basic EMAC functionality with 1Gbps
and 100Mbps link speed. 10M and half duplex mode are not supported
currently as they require IEP, the support for which will be added later.
Support for switch-dev, timestamp, etc. will be added later
by subsequent patch series.

Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...