hw/isa/vt82c686: Keep track of PIRQ/PINT pins separately

Move calculation of mask after the switch which sets the function
number for PIRQ/PINT pins to make sure the state of these pins are
kept tra

hw/isa/vt82c686: Keep track of PIRQ/PINT pins separately

Move calculation of mask after the switch which sets the function
number for PIRQ/PINT pins to make sure the state of these pins are
kept track of separately and IRQ is raised if any of them is active.

Cc: qemu-stable@nongnu.org
Fixes: 7e01bd80c1 hw/isa/vt82c686: Bring back via_isa_set_irq()
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20240410222543.0EA534E6005@zero.eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>

show more ...

hw/dma: Pass parent object to i8257_dma_init()

Set I8257 instances parent (migration isn't affected).

Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richa

hw/dma: Pass parent object to i8257_dma_init()

Set I8257 instances parent (migration isn't affected).

Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20240213114426.87836-1-philmd@linaro.org>

show more ...

hw/isa/vt82c686: Implement relocation and toggling of SuperI/O functions

The VIA south bridges are able to relocate and toggle (enable or disable) their
SuperI/O functions. So far this is hardcoded

hw/isa/vt82c686: Implement relocation and toggling of SuperI/O functions

The VIA south bridges are able to relocate and toggle (enable or disable) their
SuperI/O functions. So far this is hardcoded such that all functions are always
enabled and are located at fixed addresses.

Some PC BIOSes seem to probe for I/O occupancy before activating such a function
and issue an error in case of a conflict. Since the functions are currently
enabled on reset, conflicts are always detected. Prevent that by implementing
relocation and toggling of the SuperI/O functions.

Note that all SuperI/O functions are now deactivated upon reset (except for
VT82C686B's serial ports where Fuloong 2e's rescue-yl seems to expect them to be
enabled by default). Rely on firmware to configure the functions accordingly.

Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-Id: <20240114123911.4877-12-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>

show more ...

hw/isa/vt82c686: Consolidate the use of device_class_set_parent_realize()

Use device_class_set_parent_realize() to set parent realize() directly.

Signed-off-by: Zhao Liu <zhao1.liu@intel.com>
Revie

hw/isa/vt82c686: Consolidate the use of device_class_set_parent_realize()

Use device_class_set_parent_realize() to set parent realize() directly.

Signed-off-by: Zhao Liu <zhao1.liu@intel.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>

show more ...

hw/isa: Constify VMState

Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20231221031652.119827-38-richard.henders

hw/isa: Constify VMState

Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20231221031652.119827-38-richard.henderson@linaro.org>

show more ...

hw/audio/via-ac97: Route interrupts using via_isa_set_irq()

This device is a function of VIA south bridge and should allow setting
interrupt routing within that chip. This is implemented in
via_isa_

hw/audio/via-ac97: Route interrupts using via_isa_set_irq()

This device is a function of VIA south bridge and should allow setting
interrupt routing within that chip. This is implemented in
via_isa_set_irq().

Fixes: eb604411a78b82c468e2b8d81a9401eb8b9c7658
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-ID: <5329840e4be6dd8ae143d07cbfe61d8d2d106654.1701035944.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>

show more ...

hw/isa/vt82c686: Route PIRQ inputs using via_isa_set_irq()

The chip has 4 pins (called PIRQA-D in VT82C686B and PINTA-D in
VT8231) that are meant to be connected to PCI IRQ lines and allow
routing P

hw/isa/vt82c686: Route PIRQ inputs using via_isa_set_irq()

The chip has 4 pins (called PIRQA-D in VT82C686B and PINTA-D in
VT8231) that are meant to be connected to PCI IRQ lines and allow
routing PCI interrupts to the ISA PIC. Route these in
via_isa_set_irq() to make it possible to share them with internal
functions that can also be routed to the same ISA IRQs.

Fixes: 2fdadd02e675caca4aba4ae26317701fe2c4c901
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-ID: <8c4513d8b78fac40e6d4e65a0a4b3a7f2f278a4b.1701035944.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>

show more ...

hw/isa/vt82c686: Bring back via_isa_set_irq()

The VIA integrated south bridge chips combine several functions and
allow routing their interrupts to any of the ISA IRQs also allowing
multiple sources

hw/isa/vt82c686: Bring back via_isa_set_irq()

The VIA integrated south bridge chips combine several functions and
allow routing their interrupts to any of the ISA IRQs also allowing
multiple sources to share the same ISA IRQ. E.g. pegasos2 firmware
configures everything to use IRQ 9 but amigaone routes them to
separate ISA IRQs so the current simplified routing does not work.
Bring back via_isa_set_irq() and change it to take the component that
wants to change an IRQ and keep track of interrupt status of each
source separately and do the mapping to ISA IRQ within the ISA bridge.

This may not handle cases when an ISA IRQ is controlled by devices
directly, not going through via_isa_set_irq() such as serial, parallel
or keyboard but these IRQs being conventionally fixed are not likely
to be change by guests or share with other devices so this does not
cause a problem in practice.

This reverts commit 4e5a20b6da9b1f6d2e9621ed7eb8b239560104ae.

Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-ID: <1c3902d4166234bef0a476026441eaac3dd6cda5.1701035944.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>

show more ...

hw/isa/vt82c686: Remove via_isa_set_irq()

Now that via_isa_set_irq() is unused it can be removed.

Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland

hw/isa/vt82c686: Remove via_isa_set_irq()

Now that via_isa_set_irq() is unused it can be removed.

Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20230531211043.41724-4-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>

show more ...

hw/ide/via: Wire up IDE legacy interrupts in host device

Resolves circular depencency between IDE function and south bridge.

Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Mark Ca

hw/ide/via: Wire up IDE legacy interrupts in host device

Resolves circular depencency between IDE function and south bridge.

Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20230531211043.41724-3-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>

show more ...

hw/isa/vt82c686: Remove via_isa_set_irq()

Now that via_isa_set_irq() is unused it can be removed.

Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland

hw/isa/vt82c686: Remove via_isa_set_irq()

Now that via_isa_set_irq() is unused it can be removed.

Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20230531211043.41724-4-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>

show more ...

hw/ide/via: Wire up IDE legacy interrupts in host device

Resolves circular depencency between IDE function and south bridge.

Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Mark Ca

hw/ide/via: Wire up IDE legacy interrupts in host device

Resolves circular depencency between IDE function and south bridge.

Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20230531211043.41724-3-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>

show more ...

hw/audio/via-ac97: Basic implementation of audio playback

Add basic implementation of the AC'97 sound part used in VIA south
bridge chips. Not all features of the device is emulated, only one
playba

hw/audio/via-ac97: Basic implementation of audio playback

Add basic implementation of the AC'97 sound part used in VIA south
bridge chips. Not all features of the device is emulated, only one
playback channel is supported for now but this is enough to get sound
output from some guests using this device on pegasos2.

Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Volker Rümelin <vr_qemu@t-online.de>
Tested-by: Rene Engel <ReneEngel80@emailn.de>
Message-Id: <63b99410895312f40e7be479f581da0805e605a1.1678188711.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>

show more ...

hw/isa/vt82c686: Implement PCI IRQ routing

The real VIA south bridges implement a PCI IRQ router which is configured
by the BIOS or the OS. In order to respect these configurations, QEMU
needs to im

hw/isa/vt82c686: Implement PCI IRQ routing

The real VIA south bridges implement a PCI IRQ router which is configured
by the BIOS or the OS. In order to respect these configurations, QEMU
needs to implement it as well. The real chip may allow routing IRQs from
internal functions independently of PCI interrupts but since guests
usually configute it to a single shared interrupt we don't model that
here for simplicity.

Note: The implementation was taken from piix4_set_irq() in hw/isa/piix4.

Suggested-by: Bernhard Beschow <shentey@gmail.com>
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Bernhard Beschow <shentey@gmail.com>
Tested-by: Rene Engel <ReneEngel80@emailn.de>
Message-Id: <fbb016c7d0e19093335c237e15f5f6c62c4393b4.1678188711.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>

show more ...

Revert "hw/isa/vt82c686: Remove intermediate IRQ forwarder"

To be 'usable', QDev objects (which are QOM objects) must be
1/ initialized (at this point their properties can be modified), then
2/ real

Revert "hw/isa/vt82c686: Remove intermediate IRQ forwarder"

To be 'usable', QDev objects (which are QOM objects) must be
1/ initialized (at this point their properties can be modified), then
2/ realized (properties are consumed).
Some devices (objects) might depend on other devices. When creating
the 'QOM composition tree', parent objects can't be 'realized' until
all their children are. We might also have circular dependencies.
A common circular dependency occurs with IRQs. Device (A) has an
output IRQ wired to device (B), and device (B) has one to device (A).
When (A) is realized and connects its IRQ to an unrealized (B), the
IRQ handler on (B) is not yet created. QEMU pass IRQ between objects
as pointer. When (A) poll (B)'s IRQ, it is NULL. Later (B) is realized
and its IRQ pointers are populated, but (A) keeps a reference to a
NULL pointer.
A common pattern to bypass this circular limitation is to use 'proxy'
objects. Proxy (P) is created (and realized) before (A) and (B). Then
(A) and (B) can be created in different order, it doesn't matter: (P)
pointers are already populated.

Commit bb98e0f59cde ("hw/isa/vt82c686: Remove intermediate IRQ
forwarder") neglected the QOM/QDev circular dependency issue, and
removed the 'proxy' between the southbridge, its PCI functions and the
interrupt controller, resulting in PCI functions wiring output IRQs to
'NULL', leading to guest failures (IRQ never delivered) [1] [2].

Since we are entering feature freeze, it is safer to revert the
offending patch until we figure a way to strengthen our APIs.

[1] https://lore.kernel.org/qemu-devel/928a8552-ab62-9e6c-a492-d6453e338b9d@redhat.com/
[2] https://lore.kernel.org/qemu-devel/cover.1677628524.git.balaton@eik.bme.hu/

Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Tested-by: Rene Engel <ReneEngel80@emailn.de>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <cdfb3c5a42e505450f6803124f27856434c5b298.1677628524.git.balaton@eik.bme.hu>
[PMD: Reworded description]
Inspired-by: Bernhard Beschow <shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>

show more ...

hw/audio/via-ac97: Basic implementation of audio playback

Add basic implementation of the AC'97 sound part used in VIA south
bridge chips. Not all features of the device is emulated, only one
playba

hw/audio/via-ac97: Basic implementation of audio playback

Add basic implementation of the AC'97 sound part used in VIA south
bridge chips. Not all features of the device is emulated, only one
playback channel is supported for now but this is enough to get sound
output from some guests using this device on pegasos2.

Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Volker Rümelin <vr_qemu@t-online.de>
Tested-by: Rene Engel <ReneEngel80@emailn.de>
Message-Id: <63b99410895312f40e7be479f581da0805e605a1.1678188711.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>

show more ...

hw/isa/vt82c686: Implement PCI IRQ routing

The real VIA south bridges implement a PCI IRQ router which is configured
by the BIOS or the OS. In order to respect these configurations, QEMU
needs to im

hw/isa/vt82c686: Implement PCI IRQ routing

The real VIA south bridges implement a PCI IRQ router which is configured
by the BIOS or the OS. In order to respect these configurations, QEMU
needs to implement it as well. The real chip may allow routing IRQs from
internal functions independently of PCI interrupts but since guests
usually configute it to a single shared interrupt we don't model that
here for simplicity.

Note: The implementation was taken from piix4_set_irq() in hw/isa/piix4.

Suggested-by: Bernhard Beschow <shentey@gmail.com>
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Bernhard Beschow <shentey@gmail.com>
Tested-by: Rene Engel <ReneEngel80@emailn.de>
Message-Id: <fbb016c7d0e19093335c237e15f5f6c62c4393b4.1678188711.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>

show more ...

Revert "hw/isa/vt82c686: Remove intermediate IRQ forwarder"

To be 'usable', QDev objects (which are QOM objects) must be
1/ initialized (at this point their properties can be modified), then
2/ real

Revert "hw/isa/vt82c686: Remove intermediate IRQ forwarder"

To be 'usable', QDev objects (which are QOM objects) must be
1/ initialized (at this point their properties can be modified), then
2/ realized (properties are consumed).
Some devices (objects) might depend on other devices. When creating
the 'QOM composition tree', parent objects can't be 'realized' until
all their children are. We might also have circular dependencies.
A common circular dependency occurs with IRQs. Device (A) has an
output IRQ wired to device (B), and device (B) has one to device (A).
When (A) is realized and connects its IRQ to an unrealized (B), the
IRQ handler on (B) is not yet created. QEMU pass IRQ between objects
as pointer. When (A) poll (B)'s IRQ, it is NULL. Later (B) is realized
and its IRQ pointers are populated, but (A) keeps a reference to a
NULL pointer.
A common pattern to bypass this circular limitation is to use 'proxy'
objects. Proxy (P) is created (and realized) before (A) and (B). Then
(A) and (B) can be created in different order, it doesn't matter: (P)
pointers are already populated.

Commit bb98e0f59cde ("hw/isa/vt82c686: Remove intermediate IRQ
forwarder") neglected the QOM/QDev circular dependency issue, and
removed the 'proxy' between the southbridge, its PCI functions and the
interrupt controller, resulting in PCI functions wiring output IRQs to
'NULL', leading to guest failures (IRQ never delivered) [1] [2].

Since we are entering feature freeze, it is safer to revert the
offending patch until we figure a way to strengthen our APIs.

[1] https://lore.kernel.org/qemu-devel/928a8552-ab62-9e6c-a492-d6453e338b9d@redhat.com/
[2] https://lore.kernel.org/qemu-devel/cover.1677628524.git.balaton@eik.bme.hu/

Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Tested-by: Rene Engel <ReneEngel80@emailn.de>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <cdfb3c5a42e505450f6803124f27856434c5b298.1677628524.git.balaton@eik.bme.hu>
[PMD: Reworded description]
Inspired-by: Bernhard Beschow <shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>

show more ...

hw/audio/via-ac97: Basic implementation of audio playback

Add basic implementation of the AC'97 sound part used in VIA south
bridge chips. Not all features of the device is emulated, only one
playba

hw/audio/via-ac97: Basic implementation of audio playback

Add basic implementation of the AC'97 sound part used in VIA south
bridge chips. Not all features of the device is emulated, only one
playback channel is supported for now but this is enough to get sound
output from some guests using this device on pegasos2.

Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Volker Rümelin <vr_qemu@t-online.de>
Tested-by: Rene Engel <ReneEngel80@emailn.de>
Message-Id: <63b99410895312f40e7be479f581da0805e605a1.1678188711.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>

show more ...

hw/isa/vt82c686: Implement PCI IRQ routing

The real VIA south bridges implement a PCI IRQ router which is configured
by the BIOS or the OS. In order to respect these configurations, QEMU
needs to im

hw/isa/vt82c686: Implement PCI IRQ routing

The real VIA south bridges implement a PCI IRQ router which is configured
by the BIOS or the OS. In order to respect these configurations, QEMU
needs to implement it as well. The real chip may allow routing IRQs from
internal functions independently of PCI interrupts but since guests
usually configute it to a single shared interrupt we don't model that
here for simplicity.

Note: The implementation was taken from piix4_set_irq() in hw/isa/piix4.

Suggested-by: Bernhard Beschow <shentey@gmail.com>
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Bernhard Beschow <shentey@gmail.com>
Tested-by: Rene Engel <ReneEngel80@emailn.de>
Message-Id: <fbb016c7d0e19093335c237e15f5f6c62c4393b4.1678188711.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>

show more ...

Revert "hw/isa/vt82c686: Remove intermediate IRQ forwarder"

To be 'usable', QDev objects (which are QOM objects) must be
1/ initialized (at this point their properties can be modified), then
2/ real

Revert "hw/isa/vt82c686: Remove intermediate IRQ forwarder"

To be 'usable', QDev objects (which are QOM objects) must be
1/ initialized (at this point their properties can be modified), then
2/ realized (properties are consumed).
Some devices (objects) might depend on other devices. When creating
the 'QOM composition tree', parent objects can't be 'realized' until
all their children are. We might also have circular dependencies.
A common circular dependency occurs with IRQs. Device (A) has an
output IRQ wired to device (B), and device (B) has one to device (A).
When (A) is realized and connects its IRQ to an unrealized (B), the
IRQ handler on (B) is not yet created. QEMU pass IRQ between objects
as pointer. When (A) poll (B)'s IRQ, it is NULL. Later (B) is realized
and its IRQ pointers are populated, but (A) keeps a reference to a
NULL pointer.
A common pattern to bypass this circular limitation is to use 'proxy'
objects. Proxy (P) is created (and realized) before (A) and (B). Then
(A) and (B) can be created in different order, it doesn't matter: (P)
pointers are already populated.

Commit bb98e0f59cde ("hw/isa/vt82c686: Remove intermediate IRQ
forwarder") neglected the QOM/QDev circular dependency issue, and
removed the 'proxy' between the southbridge, its PCI functions and the
interrupt controller, resulting in PCI functions wiring output IRQs to
'NULL', leading to guest failures (IRQ never delivered) [1] [2].

Since we are entering feature freeze, it is safer to revert the
offending patch until we figure a way to strengthen our APIs.

[1] https://lore.kernel.org/qemu-devel/928a8552-ab62-9e6c-a492-d6453e338b9d@redhat.com/
[2] https://lore.kernel.org/qemu-devel/cover.1677628524.git.balaton@eik.bme.hu/

Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Tested-by: Rene Engel <ReneEngel80@emailn.de>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <cdfb3c5a42e505450f6803124f27856434c5b298.1677628524.git.balaton@eik.bme.hu>
[PMD: Reworded description]
Inspired-by: Bernhard Beschow <shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>

show more ...

hw/audio/via-ac97: Basic implementation of audio playback

Add basic implementation of the AC'97 sound part used in VIA south
bridge chips. Not all features of the device is emulated, only one
playba

hw/audio/via-ac97: Basic implementation of audio playback

Add basic implementation of the AC'97 sound part used in VIA south
bridge chips. Not all features of the device is emulated, only one
playback channel is supported for now but this is enough to get sound
output from some guests using this device on pegasos2.

Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Volker Rümelin <vr_qemu@t-online.de>
Tested-by: Rene Engel <ReneEngel80@emailn.de>
Message-Id: <63b99410895312f40e7be479f581da0805e605a1.1678188711.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>

show more ...

hw/isa/vt82c686: Implement PCI IRQ routing

The real VIA south bridges implement a PCI IRQ router which is configured
by the BIOS or the OS. In order to respect these configurations, QEMU
needs to im

hw/isa/vt82c686: Implement PCI IRQ routing

The real VIA south bridges implement a PCI IRQ router which is configured
by the BIOS or the OS. In order to respect these configurations, QEMU
needs to implement it as well. The real chip may allow routing IRQs from
internal functions independently of PCI interrupts but since guests
usually configute it to a single shared interrupt we don't model that
here for simplicity.

Note: The implementation was taken from piix4_set_irq() in hw/isa/piix4.

Suggested-by: Bernhard Beschow <shentey@gmail.com>
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Bernhard Beschow <shentey@gmail.com>
Tested-by: Rene Engel <ReneEngel80@emailn.de>
Message-Id: <fbb016c7d0e19093335c237e15f5f6c62c4393b4.1678188711.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>

show more ...

Revert "hw/isa/vt82c686: Remove intermediate IRQ forwarder"

To be 'usable', QDev objects (which are QOM objects) must be
1/ initialized (at this point their properties can be modified), then
2/ real

Revert "hw/isa/vt82c686: Remove intermediate IRQ forwarder"

To be 'usable', QDev objects (which are QOM objects) must be
1/ initialized (at this point their properties can be modified), then
2/ realized (properties are consumed).
Some devices (objects) might depend on other devices. When creating
the 'QOM composition tree', parent objects can't be 'realized' until
all their children are. We might also have circular dependencies.
A common circular dependency occurs with IRQs. Device (A) has an
output IRQ wired to device (B), and device (B) has one to device (A).
When (A) is realized and connects its IRQ to an unrealized (B), the
IRQ handler on (B) is not yet created. QEMU pass IRQ between objects
as pointer. When (A) poll (B)'s IRQ, it is NULL. Later (B) is realized
and its IRQ pointers are populated, but (A) keeps a reference to a
NULL pointer.
A common pattern to bypass this circular limitation is to use 'proxy'
objects. Proxy (P) is created (and realized) before (A) and (B). Then
(A) and (B) can be created in different order, it doesn't matter: (P)
pointers are already populated.

Commit bb98e0f59cde ("hw/isa/vt82c686: Remove intermediate IRQ
forwarder") neglected the QOM/QDev circular dependency issue, and
removed the 'proxy' between the southbridge, its PCI functions and the
interrupt controller, resulting in PCI functions wiring output IRQs to
'NULL', leading to guest failures (IRQ never delivered) [1] [2].

Since we are entering feature freeze, it is safer to revert the
offending patch until we figure a way to strengthen our APIs.

[1] https://lore.kernel.org/qemu-devel/928a8552-ab62-9e6c-a492-d6453e338b9d@redhat.com/
[2] https://lore.kernel.org/qemu-devel/cover.1677628524.git.balaton@eik.bme.hu/

Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Tested-by: Rene Engel <ReneEngel80@emailn.de>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <cdfb3c5a42e505450f6803124f27856434c5b298.1677628524.git.balaton@eik.bme.hu>
[PMD: Reworded description]
Inspired-by: Bernhard Beschow <shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>

show more ...

hw/rtc/mc146818rtc: Rename RTCState -> MC146818RtcState

RTCState only represents a Motorola MC146818 model,
not any RTC chipset. Rename the structure as MC146818RtcState
using:

$ sed -i -e s/RTCS

hw/rtc/mc146818rtc: Rename RTCState -> MC146818RtcState

RTCState only represents a Motorola MC146818 model,
not any RTC chipset. Rename the structure as MC146818RtcState
using:

$ sed -i -e s/RTCState/MC146818RtcState/g $(git grep -wl RTCState)

Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20230210233116.80311-2-philmd@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>

show more ...