hw/misc/mps2-scc: Make changes needed for AN536 FPGA image

The MPS2 SCC device is broadly the same for all FPGA images, but has
minor differences in the behaviour of the CFG registers depending on
t

hw/misc/mps2-scc: Make changes needed for AN536 FPGA image

The MPS2 SCC device is broadly the same for all FPGA images, but has
minor differences in the behaviour of the CFG registers depending on
the image. In many cases we don't really care about the functionality
controlled by these registers and a reads-as-written or similar
behaviour is sufficient for the moment.

For the AN536 the required behaviour is:

* A_CFG0 has CPU reset and halt bits
- implement as reads-as-written for the moment
* A_CFG1 has flash or ATCM address 0 remap handling
- QEMU doesn't model this; implement as reads-as-written
* A_CFG2 has QSPI select (like AN524)
- implemented (no behaviour, as with AN524)
* A_CFG3 is MCC_MSB_ADDR "additional MCC addressing bits"
- QEMU doesn't care about these, so use the existing
RAZ behaviour for convenience
* A_CFG4 is board rev (like all other images)
- no change needed
* A_CFG5 is ACLK frq in hz (like AN524)
- implemented as reads-as-written, as for other boards
* A_CFG6 is core 0 vector table base address
- implemented as reads-as-written for the moment
* A_CFG7 is core 1 vector table base address
- implemented as reads-as-written for the moment

Make the changes necessary for this; leave TODO comments where
appropriate to indicate where we might want to come back and
implement things like CPU reset.

The other aspects of the device specific to this FPGA image (like the
values of the board ID and similar registers) will be set via the
device's qdev properties.

Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20240206132931.38376-8-peter.maydell@linaro.org

show more ...

hw/misc/mps2-scc: Support using CFG0 bit 0 for remapping

On some boards, SCC config register CFG0 bit 0 controls whether
parts of the board memory map are remapped. Support this with:
* a device pr

hw/misc/mps2-scc: Support using CFG0 bit 0 for remapping

On some boards, SCC config register CFG0 bit 0 controls whether
parts of the board memory map are remapped. Support this with:
* a device property scc-cfg0 so the board can specify the
initial value of the CFG0 register
* an outbound GPIO line which tracks bit 0 and which the board
can wire up to provide the remapping

Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210504120912.23094-3-peter.maydell@linaro.org

show more ...

hw/misc/mps2-scc: Add "QEMU interface" comment

The MPS2 SCC device doesn't have any documentation of its properties;
add a "QEMU interface" format comment describing them.

Signed-off-by: Peter Mayd

hw/misc/mps2-scc: Add "QEMU interface" comment

The MPS2 SCC device doesn't have any documentation of its properties;
add a "QEMU interface" format comment describing them.

Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210504120912.23094-2-peter.maydell@linaro.org

show more ...

hw/misc/mps2-scc: Implement CFG_REG5 and CFG_REG6 for MPS3 AN524

The AN524 version of the SCC interface has different behaviour for
some of the CFG registers; implement it.

Each board in this famil

hw/misc/mps2-scc: Implement CFG_REG5 and CFG_REG6 for MPS3 AN524

The AN524 version of the SCC interface has different behaviour for
some of the CFG registers; implement it.

Each board in this family can have minor differences in the meaning
of the CFG registers, so rather than trying to specify all the
possible semantics via individual device properties, we make the
behaviour conditional on the part-number field of the SCC_ID register
which the board code already passes us.

For the AN524, the differences are:
* CFG3 is reserved rather than being board switches
* CFG5 is a new register ("ACLK Frequency in Hz")
* CFG6 is a new register ("Clock divider for BRAM")

We implement both of the new registers as reads-as-written.

Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-11-peter.maydell@linaro.org

show more ...

hw/misc/mps2-scc: Support configurable number of OSCCLK values

Currently the MPS2 SCC device implements a fixed number of OSCCLK
values (3). The variant of this device in the MPS3 AN524 board has 6

hw/misc/mps2-scc: Support configurable number of OSCCLK values

Currently the MPS2 SCC device implements a fixed number of OSCCLK
values (3). The variant of this device in the MPS3 AN524 board has 6
OSCCLK values. Switch to using a PROP_ARRAY, which allows board code
to specify how large the OSCCLK array should be as well as its
values.

With a variable-length property array, the SCC no longer specifies
default values for the OSCCLKs, so we must set them explicitly in the
board code. This defaults are actually incorrect for the an521 and
an505; we will correct this bug in a following patch.

This is a migration compatibility break for all the mps boards.

Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-3-peter.maydell@linaro.org

show more ...

hw/misc/mps2-scc: Use the LED device

Per the 'ARM MPS2 and MPS2+ FPGA Prototyping Boards Technical
Reference Manual' (100112_0200_07_en):

2.1 Overview of the MPS2 and MPS2+ hardware

The

hw/misc/mps2-scc: Use the LED device

Per the 'ARM MPS2 and MPS2+ FPGA Prototyping Boards Technical
Reference Manual' (100112_0200_07_en):

2.1 Overview of the MPS2 and MPS2+ hardware

The MPS2 and MPS2+ FPGA Prototyping Boards contain the
following components and interfaces:

* User switches and user LEDs:

- Two green LEDs and two push buttons that connect to
the FPGA.
- Eight green LEDs and one 8-way dip switch that connect
to the MCC.

Add the 8 LEDs connected to the MCC.

This replaces the 'mps2_scc_leds' trace events by the generic
'led_set_intensity' event.

Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Message-Id: <20200912134041.946260-7-f4bug@amsat.org>

show more ...

Use OBJECT_DECLARE_SIMPLE_TYPE when possible

This converts existing DECLARE_INSTANCE_CHECKER usage to
OBJECT_DECLARE_SIMPLE_TYPE when possible.

$ ./scripts/codeconverter/converter.py -i \
--patte

Use OBJECT_DECLARE_SIMPLE_TYPE when possible

This converts existing DECLARE_INSTANCE_CHECKER usage to
OBJECT_DECLARE_SIMPLE_TYPE when possible.

$ ./scripts/codeconverter/converter.py -i \
--pattern=AddObjectDeclareSimpleType $(git grep -l '' -- '*.[ch]')

Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Acked-by: Paul Durrant <paul@xen.org>
Message-Id: <20200916182519.415636-6-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>

show more ...

Use DECLARE_*CHECKER* macros

Generated using:

$ ./scripts/codeconverter/converter.py -i \
--pattern=TypeCheckMacro $(git grep -l '' -- '*.[ch]')

Reviewed-by: Daniel P. Berrangé <berrange@redha

Use DECLARE_*CHECKER* macros

Generated using:

$ ./scripts/codeconverter/converter.py -i \
--pattern=TypeCheckMacro $(git grep -l '' -- '*.[ch]')

Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20200831210740.126168-12-ehabkost@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20200831210740.126168-13-ehabkost@redhat.com>
Message-Id: <20200831210740.126168-14-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>

show more ...

Move QOM typedefs and add missing includes

Some typedefs and macros are defined after the type check macros.
This makes it difficult to automatically replace their
definitions with OBJECT_DECLARE_TY

Move QOM typedefs and add missing includes

Some typedefs and macros are defined after the type check macros.
This makes it difficult to automatically replace their
definitions with OBJECT_DECLARE_TYPE.

Patch generated using:

$ ./scripts/codeconverter/converter.py -i \
--pattern=QOMStructTypedefSplit $(git grep -l '' -- '*.[ch]')

which will split "typdef struct { ... } TypedefName"
declarations.

Followed by:

$ ./scripts/codeconverter/converter.py -i --pattern=MoveSymbols \
$(git grep -l '' -- '*.[ch]')

which will:
- move the typedefs and #defines above the type check macros
- add missing #include "qom/object.h" lines if necessary

Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20200831210740.126168-9-ehabkost@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20200831210740.126168-10-ehabkost@redhat.com>
Message-Id: <20200831210740.126168-11-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>

show more ...

hw/misc/mps2_scc: Implement MPS2 Serial Communication Controller

Implement a model of the Serial Communication Controller (SCC) found
in MPS2 FPGA images.

The primary purpose of this device is to c

hw/misc/mps2_scc: Implement MPS2 Serial Communication Controller

Implement a model of the Serial Communication Controller (SCC) found
in MPS2 FPGA images.

The primary purpose of this device is to communicate with the
Motherboard Configuration Controller (MCC) which is located on
the MPS board itself, outside the FPGA image. This is used
for programming the MPS clock generators. The SCC also has
some basic ID registers and an output for the board LEDs.

Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 1500029487-14822-7-git-send-email-peter.maydell@linaro.org

show more ...