sys: Remove $FreeBSD$: one-line sh pattern

Remove /^\s*#[#!]?\s*\$FreeBSD\$.*$\n/

e1000: remove duplicated phy codes

Add two files base.c and base.h to reduce the redundancy
in the silicon family code.
Remove the code duplication from e1000_82575 files.
Clean family specific func

e1000: remove duplicated phy codes

Add two files base.c and base.h to reduce the redundancy
in the silicon family code.
Remove the code duplication from e1000_82575 files.
Clean family specific functions from base.
Fix up a stray and duplicate function declaration.

Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Signed-off-by: Guinan Sun <guinanx.sun@intel.com>
Reviewed-by: Wei Zhao <wei.zhao1@intel.com>

Approved by: imp
Obtained from: DPDK (44dddd14059f151f39f7e075b887decfc9a10f11)
MFC after: 1 week

show more ...

if_em.ko: fix module build outside of kernel build environment

MFC after: 3 days

Use symlinks for kernel modules rather than hardlinks

When aliasing a kernel module to a different name (ie if_igb for if_em),
it's better to use symlinks than hard links. kldxref will omit entries

Use symlinks for kernel modules rather than hardlinks

When aliasing a kernel module to a different name (ie if_igb for if_em),
it's better to use symlinks than hard links. kldxref will omit entries for
the links, ensuring that the loaded module has the correct name.

Reviewed by: imp
MFC after: 2 weeks
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D19979

show more ...

Hard link if_igb.ko to if_em.ko. Use a LINK directive to ensure that
this is more friendly to the tree.

Tested this with loader.conf:if_igb_load="YES" and it does the right
thing.

Submitted by: Ia

Hard link if_igb.ko to if_em.ko. Use a LINK directive to ensure that
this is more friendly to the tree.

Tested this with loader.conf:if_igb_load="YES" and it does the right
thing.

Submitted by: Ian Lepore <ian@freebsd.org>

show more ...

Fix symlink if_igb.ko in -current such that its relative and doesn't
end up with non-standard DESTDIR information in its symlink. This
can happen very trivially if the release scripts are used.

Spo

Fix symlink if_igb.ko in -current such that its relative and doesn't
end up with non-standard DESTDIR information in its symlink. This
can happen very trivially if the release scripts are used.

Sponsored by: Limelight Networks

show more ...

sys/modules: normalize .CURDIR-relative paths to SRCTOP

This simplifies make output/logic

Tested with: `cd sys/modules; make ALL_MODULES=` on amd64
MFC after: 1 month
Sponsored by: Dell EMC Isilon

Deprecate kernel configuration option EM_MULTIQUEUE now that the em(4)
driver conforms to iflib.

Set CFLAGS correctly for sys/modules/em

Unbreak gcc sparc64 builds (or any gcc build that uses em(4)).

Reported by: lidl@freebsd.org

Migrate e1000 to the IFLIB framework:
- em(4) igb(4) and lem(4)
- deprecate the igb device from kernel configurations
- create a symbolic link in /boot/kernel from if_em.ko to if_igb.ko

Devices test

Migrate e1000 to the IFLIB framework:
- em(4) igb(4) and lem(4)
- deprecate the igb device from kernel configurations
- create a symbolic link in /boot/kernel from if_em.ko to if_igb.ko

Devices tested:
- 82574L
- I218-LM
- 82546GB
- 82579LM
- I350
- I217

Please report problems to freebsd-net@freebsd.org

Partial review from jhb and suggestions on how to *not* brick folks who
originally would have lost their igbX device.

Submitted by: mmacy@nextbsd.org
MFC after: 2 weeks
Relnotes: yes
Sponsored by: Limelight Networks and Dell EMC Isilon
Differential Revision: https://reviews.freebsd.org/D8299

show more ...

Include opt_em.h now that there are actual kernel compile options for em(4).

Submitted by: jfv
MFC after: 2 week
Sponsored by: Limelight Networks

Change EM_MULTIQUEUE to a real kernconf entry and enable support for
up to 2 rx/tx queues for the 82574.

Program the 82574 to enable 5 msix vectors, assign 1 to each rx queue,
1 to each tx queue and

Change EM_MULTIQUEUE to a real kernconf entry and enable support for
up to 2 rx/tx queues for the 82574.

Program the 82574 to enable 5 msix vectors, assign 1 to each rx queue,
1 to each tx queue and 1 to the link handler.

Inspired by DragonFlyBSD, enable some RSS logic for handling tx queue
handling/processing.

Move multiqueue handler functions so that they line up better in a diff
review to if_igb.c

Always enqueue tx work to be done in em_mq_start, if unable to acquire
the TX lock, then this will be processed in the background later by the
taskqueue. Remove mbuf argument from em_start_mq_locked() as the work
is always enqueued. (stolen from igb)

Setup TARC, TXDCTL and RXDCTL registers for better performance and stability
in multiqueue and singlequeue implementations. Handle Intel errata 3 and
generic multiqueue behavior with the initialization of TARC(0) and TARC(1)

Bind interrupt threads to cpus in order. (stolen from igb)

Add 2 new DDB functions, one to display the queue(s) and their settings and
one to reset the adapter. Primarily used for debugging.

In the multiqueue configuration, bump RXD and TXD ring size to max for the
adapter (4096). Setup an RDTR of 64 and an RADV of 128 in multiqueue configuration
to cut down on the number of interrupts. RADV was arbitrarily set to 2x RDTR
and can be adjusted as needed.

Cleanup the display in top a bit to make it clearer where the taskqueue threads
are running and what they should be doing.

Ensure that both queues are processed by em_local_timer() by writing them both
to the IMS register to generate soft interrupts.

Ensure that an soft interrupt is generated when em_msix_link() is run so that
any races between assertion of the link/status interrupt and a rx/tx interrupt
are handled.

Document existing tuneables: hw.em.eee_setting, hw.em.msix, hw.em.smart_pwr_down, hw.em.sbp

Document use of hw.em.num_queues and the new kernel option EM_MULTIQUEUE

Thanks to Intel for their continued support of FreeBSD.

Reviewed by: erj jfv hiren gnn wblock
Obtained from: Intel Corporation
MFC after: 2 weeks
Relnotes: Yes
Sponsored by: Limelight Networks
Differential Revision: https://reviews.freebsd.org/D1994

show more ...

Move most of the 15 variations on generating opt_inet.h and
opt_inet6.h into kmod.mk by forcing almost everybody to eat the same
dogfood. While at it, consolidate the opt_bpf.h and opt_mroute.h
targe

Move most of the 15 variations on generating opt_inet.h and
opt_inet6.h into kmod.mk by forcing almost everybody to eat the same
dogfood. While at it, consolidate the opt_bpf.h and opt_mroute.h
targets here too.

show more ...

Use src.opts.mk in preference to bsd.own.mk except where we need stuff
from the latter.

Change the E1000 driver option header handling to match the
ixgbe driver. As it was, when building them as a module INET
and INET6 are not defined. In these drivers it does not cause
a panic, however

Change the E1000 driver option header handling to match the
ixgbe driver. As it was, when building them as a module INET
and INET6 are not defined. In these drivers it does not cause
a panic, however it does result in different behavior in the
ioctl routine when you are using a module vs static, and I
think the behavior should be the same.

MFC after: 3 days

show more ...

Add a source file needed for module linking.

MFC after: 4 days

Remove unnecessary clean target in em(4), igb(4) and ixgbe(4).
While here also remove man target in igb(4).

Reviewed by: jfv

Add missing module Makefile for ixgbe and em MFCs

Add new source to the loadable em build, thought
it wasnt needed but it is.

Update to igb and em:

em revision 7.0.0:
- Using driver devclass, seperate legacy (pre-pcie) code
into a seperate source file. This will at least help
protect against regression issues. It co

Update to igb and em:

em revision 7.0.0:
- Using driver devclass, seperate legacy (pre-pcie) code
into a seperate source file. This will at least help
protect against regression issues. It compiles along
with em, and is transparent to end use, devices in each
appear to be 'emX'. When using em in a modular form this
also allows the legacy stuff to be defined out.
- Add tx and rx rings as in igb, in the 82574 this becomes
actual multiqueue for the first time (2 queues) while in
other PCIE adapters its just make code cleaner.
- Add RX mbuf handling logic that matches igb, this will
eliminate packet drops due to temporary mbuf shortage.

igb revision 1.9.3:
- Following the ixgbe code, use a new approach in what
was called 'get_buf', the routine now has been made
independent of rxeof, it now does the update to the
engine TDT register, this design allows temporary
mbuf resources to become non-critical, not requiring
a packet to be discarded, instead it just returns and
does not increment the tail pointer.
- With the above change it was also unnecessary to keep
'spare' maps around, since we do not have the discard
issue.
- Performance tweaks and improvements to the code also.

MFC in a week

show more ...

Add opt_inet.h which has been needed since r184717 introducing
checks for #ifdef INET.

MFC after: 54 days

Change to build module with new directory tree

MFC after:ASAP

This delta has a few important items:

PR 122839 is fixed in both em and in igb

Second, the issue on building modules since the static kernel
build changes is now resolved. I was not able to get the

This delta has a few important items:

PR 122839 is fixed in both em and in igb

Second, the issue on building modules since the static kernel
build changes is now resolved. I was not able to get the fancier
directory hierarchy working, but this works, both em and igb
build as modules now.

Third, there is now support in em for two new NICs, Hartwell
(or 82574) is a low cost PCIE dual port adapter that has MSIX,
for this release it uses 3 vectors only, RX, TX, and LINK. In
the next release I will add a second TX and RX queue. Also, there
is support here for ICH10, the followon to ICH9. Both of these are
early releases, general availability will follow soon.

Fourth: On Hartwell and ICH10 we now have IEEE 1588 PTP support,
I have implemented this in a provisional way so that early adopters
may try and comment on the functionality. The IOCTL structure may
change. This feature is off by default, you need to edit the Makefile
and add the EM_TIMESYNC define to get the code.

Enjoy all!!

show more ...

This update primarily addresses the ability to have both the em
and the igb driver static in the kernel. But it also reflects
some other bug fixes in my development stream at Intel.
PR 122373 is also

This update primarily addresses the ability to have both the em
and the igb driver static in the kernel. But it also reflects
some other bug fixes in my development stream at Intel.
PR 122373 is also fixed in this code.

show more ...

Remove option headers that do not exist and are not used
from the Makefiles in sys/modules.
(opt_devfs.h, opt_bdg.h, opt_emu10kx.h and opt_uslcom.h)

Approved by: rwatson (mentor)