arm64: dts: update SolidRun Armada 8040 phy interface types

Update the SolidRun Armada 8040 platforms phy interface types from the
old 10gbase-kr to the newer and more correct 10gbase-r.

Signed-off

arm64: dts: update SolidRun Armada 8040 phy interface types

Update the SolidRun Armada 8040 platforms phy interface types from the
old 10gbase-kr to the newer and more correct 10gbase-r.

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>

show more ...

arm64: dts: add support for Macchiatobin Single Shot board

Add DT support for the Macchiatobin Single Shot board from SolidRun,
which is similar to the Double Shot board, but does not have the
10G 3

arm64: dts: add support for Macchiatobin Single Shot board

Add DT support for the Macchiatobin Single Shot board from SolidRun,
which is similar to the Double Shot board, but does not have the
10G 3310 PHYs - the two ethernet ports are instead connected directly
to the SFP+ cages.

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>

show more ...

arm64: dts: marvell: mcbin: fix eth3 connector name

The right most SFP connector on the Macchiatobin board and schematics is
marked as CON13/CON14.

Signed-off-by: Baruch Siach <baruch@tkos.co.il>
S

arm64: dts: marvell: mcbin: fix eth3 connector name

The right most SFP connector on the Macchiatobin board and schematics is
marked as CON13/CON14.

Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>

show more ...

arm64: dts: marvell: mcbin: enable the fourth network interface

This patch enables the fourth network interface on the Marvell
Macchiatobin. It is configured in the 2500Base-X PHY mode. The SFP cage

arm64: dts: marvell: mcbin: enable the fourth network interface

This patch enables the fourth network interface on the Marvell
Macchiatobin. It is configured in the 2500Base-X PHY mode. The SFP cage
is also described.

Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>

show more ...

arm64: dts: marvell: mcbin: add 10G SFP support

This patch adds the SFP cage description in the Marvell Armada 8040
mcbin, for both 10G interfaces.

Signed-off-by: Russell King <rmk+kernel@armlinux.

arm64: dts: marvell: mcbin: add 10G SFP support

This patch adds the SFP cage description in the Marvell Armada 8040
mcbin, for both 10G interfaces.

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
[Antoine: small reworks, commit message]
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>

show more ...

arm64: dts: marvell: armada-8040-mcbin: use SPDX-License-Identifier

Follow the recent trend for the license description, and also fix the
wrongly stated X11 to MIT.

As already pointed on the DT ML,

arm64: dts: marvell: armada-8040-mcbin: use SPDX-License-Identifier

Follow the recent trend for the license description, and also fix the
wrongly stated X11 to MIT.

As already pointed on the DT ML, the X11 license text [1] is explicitly
for the X Consortium and has a couple of extra clauses. The MIT
license text [2] is actually what the current DT files claim.

[1] https://spdx.org/licenses/X11.html
[2] https://spdx.org/licenses/MIT.html

Cc: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>

show more ...

arm64: dts: marvell: mcbin: fix board name typo

A 'C' was missing in the model name, this patch fixes it.

Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Gregory CLEMENT <gregory.cle

arm64: dts: marvell: mcbin: fix board name typo

A 'C' was missing in the model name, this patch fixes it.

Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>

show more ...

arm64: dts: marvell: mcbin: enable uart headers

Add description of the J25 and J27 UART headers of the Macchiatobin. They use
uart peripherals that the CP0 (J25) and CP1 (J27) provide.

Even though

arm64: dts: marvell: mcbin: enable uart headers

Add description of the J25 and J27 UART headers of the Macchiatobin. They use
uart peripherals that the CP0 (J25) and CP1 (J27) provide.

Even though J25 and J27 are labeled as UART header, the pins on these headers
can be muxed for other purposes. But the UART functionality is useful when the
board is mounted in an ATX style enclosure, since the console UART is not
accessible through the microUSB at CON9.

Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>

show more ...

arm64: dts: marvell: add Ethernet aliases

This patch adds Ethernet aliases in the Marvell Armada 7040 DB, 8040 DB
and 8040 mcbin device trees so that the bootloader setup the MAC
addresses correctly

arm64: dts: marvell: add Ethernet aliases

This patch adds Ethernet aliases in the Marvell Armada 7040 DB, 8040 DB
and 8040 mcbin device trees so that the bootloader setup the MAC
addresses correctly.

Signed-off-by: Yan Markman <ymarkman@marvell.com>
[Antoine: commit message, small fixes]
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>

show more ...

arm64: dts: marvell: replace cpm by cp0, cps by cp1

In preparation for the introduction of more than 2 CPs in upcoming
SoCs, it makes sense to move away from the "CP master" (cpm) and "CP
slave" (cp

arm64: dts: marvell: replace cpm by cp0, cps by cp1

In preparation for the introduction of more than 2 CPs in upcoming
SoCs, it makes sense to move away from the "CP master" (cpm) and "CP
slave" (cps) naming, and use instead cp0/cp1.

This commit is the result of:

sed 's%cpm%cp0g%' arch/arm64/boot/dts/marvell/*
sed 's%cps%cp1g%' arch/arm64/boot/dts/marvell/*

So it is a purely mechaninal change.

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Suggested-by: Hanna Hawa <hannah@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>

show more ...

arm64: dts: fix unit-address leading 0s

Fix dtc warnings for 'simple_bus_reg' due to leading 0s. Converted using
the following command:

perl -p -i -e 's/\@0+([0-9a-f])/\@$1/g' `find arch/arm64/boot

arm64: dts: fix unit-address leading 0s

Fix dtc warnings for 'simple_bus_reg' due to leading 0s. Converted using
the following command:

perl -p -i -e 's/\@0+([0-9a-f])/\@$1/g' `find arch/arm64/boot/dts -type -f -name '*.dts*'

Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

show more ...

arm64: dts: marvell: mcbin: add comphy references to Ethernet ports

This patch adds comphy phandles to the Ethernet ports in the mcbin
device tree. The comphy is used to configure the serdes PHYs us

arm64: dts: marvell: mcbin: add comphy references to Ethernet ports

This patch adds comphy phandles to the Ethernet ports in the mcbin
device tree. The comphy is used to configure the serdes PHYs used by
these ports.

Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>

show more ...

arm64: dts: marvell: add UART muxing on Armada 7K/8K

This commit adds the relevant details in the Armada 7K/8K Device Tree
to properly mux the UART used for the serial console. Since there is
basica

arm64: dts: marvell: add UART muxing on Armada 7K/8K

This commit adds the relevant details in the Armada 7K/8K Device Tree
to properly mux the UART used for the serial console. Since there is
basically only one possible muxing for the UART0 on the AP, the muxing
configuration is described in armada-ap806.dtsi, and selected from the
individual boards (other boards could be using a different UART).

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>

show more ...

arm64: dts: marvell: mcbin: enable more networking ports

This patch enables the two GE/SFP ports. They are configured in 10GKR
mode by default. To do this the cpm_xdmio is enabled as well, and two
p

arm64: dts: marvell: mcbin: enable more networking ports

This patch enables the two GE/SFP ports. They are configured in 10GKR
mode by default. To do this the cpm_xdmio is enabled as well, and two
phy descriptions are added.

Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Tested-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>

show more ...

arm64: dts: marvell: mcbin: add an stdout-path

This patch adds an stdout-path to the mcbin device tree. This allows to
use earlycon.

Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com

arm64: dts: marvell: mcbin: add an stdout-path

This patch adds an stdout-path to the mcbin device tree. This allows to
use earlycon.

Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>

show more ...

arm64: dts: marvell: mcbin: add support for PCIe

Add support for PCIe with the the PCIe reset signal wired up to the
appropriate GPIO pin.

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
T

arm64: dts: marvell: mcbin: add support for PCIe

Add support for PCIe with the the PCIe reset signal wired up to the
appropriate GPIO pin.

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
(excepted the reset part)
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>

show more ...

arm64: dts: marvell: mcbin: add support for i2c mux

The MACCHIATOBin board has a PCA9548 I2C mux for the SFP ports on
CP100 master I2C bus 1. Add the DT description for it.

Signed-off-by: Russell

arm64: dts: marvell: mcbin: add support for i2c mux

The MACCHIATOBin board has a PCA9548 I2C mux for the SFP ports on
CP100 master I2C bus 1. Add the DT description for it.

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>

show more ...

arm64: dts: marvell: fix USB3 regulator definition on MacchiatoBin

Due to the lack of GPIO support, the USB3 regulator definition was
left unfinished in the MacchiatoBin DT description. Now that GPI

arm64: dts: marvell: fix USB3 regulator definition on MacchiatoBin

Due to the lack of GPIO support, the USB3 regulator definition was
left unfinished in the MacchiatoBin DT description. Now that GPIO
support is available, this commit adjusts the Device Tree to properly
describe the USB3 regulator.

[gregory.clement@free-electrons.com: use commit log from Thomas]

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>

show more ...

arm64: dts: marvell: mcbin: add pinctrl nodes

Add pinctrl nodes to describe the CPM I2C0 and CPS SPI1 settings.

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Gregory CLEME

arm64: dts: marvell: mcbin: add pinctrl nodes

Add pinctrl nodes to describe the CPM I2C0 and CPS SPI1 settings.

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>

show more ...

arm64: dts: marvell: mcbin: enable the mdio node

Since the mdio nodes are disabled by default now, we should explicitly
enable these nodes at the board level when they are used. Enable the
cpm_mdio

arm64: dts: marvell: mcbin: enable the mdio node

Since the mdio nodes are disabled by default now, we should explicitly
enable these nodes at the board level when they are used. Enable the
cpm_mdio node for the 8040-mcbin.

Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>

show more ...

arm64: dts: marvell: 8040-mcbin: Enable 1GB Ethernet

Enable the 1GB Ethernet interface that lives on the slave CP110,
with its corresponding phy (that oddly lives on the master CP110).

Signed-off-b

arm64: dts: marvell: 8040-mcbin: Enable 1GB Ethernet

Enable the 1GB Ethernet interface that lives on the slave CP110,
with its corresponding phy (that oddly lives on the master CP110).

Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>

show more ...

arm64: dts: marvell: mcbin: add sdhci

Add sdhci support for MACCHIATOBin boards. This uses the AP806 SDHCI
for eMMC and CP110 master for the SD card slot.

Signed-off-by: Russell King <rmk+kernel@a

arm64: dts: marvell: mcbin: add sdhci

Add sdhci support for MACCHIATOBin boards. This uses the AP806 SDHCI
for eMMC and CP110 master for the SD card slot.

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>

show more ...

arm64: dts: marvell: Add DT for MACCHIATOBin board

Add a cut-down version of the DTS file for the community board
MACCHIATOBin from SolidRun based on Marvell Armada 8040 SoC to suit
the current main

arm64: dts: marvell: Add DT for MACCHIATOBin board

Add a cut-down version of the DTS file for the community board
MACCHIATOBin from SolidRun based on Marvell Armada 8040 SoC to suit
the current mainlined Armada 8040 state.

This brings support for mainly SATA, SPI flash and UART. The USB
descriptions are included but are not tested in this form due to the
lack of mainline GPIO.

Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Acked-by: Rabeeh Khoury <rabeeh@solid-run.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>

show more ...