1 // SPDX-License-Identifier: GPL-2.0-or-later
2 /*
3 * Synopsys DesignWare Multimedia Card Interface driver
4 * (Based on NXP driver for lpc 31xx)
5 *
6 * Copyright (C) 2009 NXP Semiconductors
7 * Copyright (C) 2009, 2010 Imagination Technologies Ltd.
8 */
9
10 #include <linux/blkdev.h>
11 #include <linux/clk.h>
12 #include <linux/debugfs.h>
13 #include <linux/device.h>
14 #include <linux/dma-mapping.h>
15 #include <linux/err.h>
16 #include <linux/init.h>
17 #include <linux/interrupt.h>
18 #include <linux/iopoll.h>
19 #include <linux/ioport.h>
20 #include <linux/module.h>
21 #include <linux/platform_device.h>
22 #include <linux/pm_runtime.h>
23 #include <linux/seq_file.h>
24 #include <linux/slab.h>
25 #include <linux/stat.h>
26 #include <linux/delay.h>
27 #include <linux/irq.h>
28 #include <linux/mmc/card.h>
29 #include <linux/mmc/host.h>
30 #include <linux/mmc/mmc.h>
31 #include <linux/mmc/sd.h>
32 #include <linux/mmc/sdio.h>
33 #include <linux/bitops.h>
34 #include <linux/regulator/consumer.h>
35 #include <linux/of.h>
36 #include <linux/of_gpio.h>
37 #include <linux/mmc/slot-gpio.h>
38
39 #include "dw_mmc.h"
40
41 /* Common flag combinations */
42 #define DW_MCI_DATA_ERROR_FLAGS (SDMMC_INT_DRTO | SDMMC_INT_DCRC | \
43 SDMMC_INT_HTO | SDMMC_INT_SBE | \
44 SDMMC_INT_EBE | SDMMC_INT_HLE)
45 #define DW_MCI_CMD_ERROR_FLAGS (SDMMC_INT_RTO | SDMMC_INT_RCRC | \
46 SDMMC_INT_RESP_ERR | SDMMC_INT_HLE)
47 #define DW_MCI_ERROR_FLAGS (DW_MCI_DATA_ERROR_FLAGS | \
48 DW_MCI_CMD_ERROR_FLAGS)
49 #define DW_MCI_SEND_STATUS 1
50 #define DW_MCI_RECV_STATUS 2
51 #define DW_MCI_DMA_THRESHOLD 16
52
53 #define DW_MCI_FREQ_MAX 200000000 /* unit: HZ */
54 #define DW_MCI_FREQ_MIN 100000 /* unit: HZ */
55
56 #define IDMAC_INT_CLR (SDMMC_IDMAC_INT_AI | SDMMC_IDMAC_INT_NI | \
57 SDMMC_IDMAC_INT_CES | SDMMC_IDMAC_INT_DU | \
58 SDMMC_IDMAC_INT_FBE | SDMMC_IDMAC_INT_RI | \
59 SDMMC_IDMAC_INT_TI)
60
61 #define DESC_RING_BUF_SZ PAGE_SIZE
62
63 struct idmac_desc_64addr {
64 u32 des0; /* Control Descriptor */
65 #define IDMAC_OWN_CLR64(x) \
66 !((x) & cpu_to_le32(IDMAC_DES0_OWN))
67
68 u32 des1; /* Reserved */
69
70 u32 des2; /*Buffer sizes */
71 #define IDMAC_64ADDR_SET_BUFFER1_SIZE(d, s) \
72 ((d)->des2 = ((d)->des2 & cpu_to_le32(0x03ffe000)) | \
73 ((cpu_to_le32(s)) & cpu_to_le32(0x1fff)))
74
75 u32 des3; /* Reserved */
76
77 u32 des4; /* Lower 32-bits of Buffer Address Pointer 1*/
78 u32 des5; /* Upper 32-bits of Buffer Address Pointer 1*/
79
80 u32 des6; /* Lower 32-bits of Next Descriptor Address */
81 u32 des7; /* Upper 32-bits of Next Descriptor Address */
82 };
83
84 struct idmac_desc {
85 __le32 des0; /* Control Descriptor */
86 #define IDMAC_DES0_DIC BIT(1)
87 #define IDMAC_DES0_LD BIT(2)
88 #define IDMAC_DES0_FD BIT(3)
89 #define IDMAC_DES0_CH BIT(4)
90 #define IDMAC_DES0_ER BIT(5)
91 #define IDMAC_DES0_CES BIT(30)
92 #define IDMAC_DES0_OWN BIT(31)
93
94 __le32 des1; /* Buffer sizes */
95 #define IDMAC_SET_BUFFER1_SIZE(d, s) \
96 ((d)->des1 = ((d)->des1 & cpu_to_le32(0x03ffe000)) | (cpu_to_le32((s) & 0x1fff)))
97
98 __le32 des2; /* buffer 1 physical address */
99
100 __le32 des3; /* buffer 2 physical address */
101 };
102
103 /* Each descriptor can transfer up to 4KB of data in chained mode */
104 #define DW_MCI_DESC_DATA_LENGTH 0x1000
105
106 #if defined(CONFIG_DEBUG_FS)
dw_mci_req_show(struct seq_file * s,void * v)107 static int dw_mci_req_show(struct seq_file *s, void *v)
108 {
109 struct dw_mci_slot *slot = s->private;
110 struct mmc_request *mrq;
111 struct mmc_command *cmd;
112 struct mmc_command *stop;
113 struct mmc_data *data;
114
115 /* Make sure we get a consistent snapshot */
116 spin_lock_bh(&slot->host->lock);
117 mrq = slot->mrq;
118
119 if (mrq) {
120 cmd = mrq->cmd;
121 data = mrq->data;
122 stop = mrq->stop;
123
124 if (cmd)
125 seq_printf(s,
126 "CMD%u(0x%x) flg %x rsp %x %x %x %x err %d\n",
127 cmd->opcode, cmd->arg, cmd->flags,
128 cmd->resp[0], cmd->resp[1], cmd->resp[2],
129 cmd->resp[2], cmd->error);
130 if (data)
131 seq_printf(s, "DATA %u / %u * %u flg %x err %d\n",
132 data->bytes_xfered, data->blocks,
133 data->blksz, data->flags, data->error);
134 if (stop)
135 seq_printf(s,
136 "CMD%u(0x%x) flg %x rsp %x %x %x %x err %d\n",
137 stop->opcode, stop->arg, stop->flags,
138 stop->resp[0], stop->resp[1], stop->resp[2],
139 stop->resp[2], stop->error);
140 }
141
142 spin_unlock_bh(&slot->host->lock);
143
144 return 0;
145 }
146 DEFINE_SHOW_ATTRIBUTE(dw_mci_req);
147
dw_mci_regs_show(struct seq_file * s,void * v)148 static int dw_mci_regs_show(struct seq_file *s, void *v)
149 {
150 struct dw_mci *host = s->private;
151
152 pm_runtime_get_sync(host->dev);
153
154 seq_printf(s, "STATUS:\t0x%08x\n", mci_readl(host, STATUS));
155 seq_printf(s, "RINTSTS:\t0x%08x\n", mci_readl(host, RINTSTS));
156 seq_printf(s, "CMD:\t0x%08x\n", mci_readl(host, CMD));
157 seq_printf(s, "CTRL:\t0x%08x\n", mci_readl(host, CTRL));
158 seq_printf(s, "INTMASK:\t0x%08x\n", mci_readl(host, INTMASK));
159 seq_printf(s, "CLKENA:\t0x%08x\n", mci_readl(host, CLKENA));
160
161 pm_runtime_put_autosuspend(host->dev);
162
163 return 0;
164 }
165 DEFINE_SHOW_ATTRIBUTE(dw_mci_regs);
166
dw_mci_init_debugfs(struct dw_mci_slot * slot)167 static void dw_mci_init_debugfs(struct dw_mci_slot *slot)
168 {
169 struct mmc_host *mmc = slot->mmc;
170 struct dw_mci *host = slot->host;
171 struct dentry *root;
172
173 root = mmc->debugfs_root;
174 if (!root)
175 return;
176
177 debugfs_create_file("regs", S_IRUSR, root, host, &dw_mci_regs_fops);
178 debugfs_create_file("req", S_IRUSR, root, slot, &dw_mci_req_fops);
179 debugfs_create_u32("state", S_IRUSR, root, &host->state);
180 debugfs_create_xul("pending_events", S_IRUSR, root,
181 &host->pending_events);
182 debugfs_create_xul("completed_events", S_IRUSR, root,
183 &host->completed_events);
184 }
185 #endif /* defined(CONFIG_DEBUG_FS) */
186
dw_mci_ctrl_reset(struct dw_mci * host,u32 reset)187 static bool dw_mci_ctrl_reset(struct dw_mci *host, u32 reset)
188 {
189 u32 ctrl;
190
191 ctrl = mci_readl(host, CTRL);
192 ctrl |= reset;
193 mci_writel(host, CTRL, ctrl);
194
195 /* wait till resets clear */
196 if (readl_poll_timeout_atomic(host->regs + SDMMC_CTRL, ctrl,
197 !(ctrl & reset),
198 1, 500 * USEC_PER_MSEC)) {
199 dev_err(host->dev,
200 "Timeout resetting block (ctrl reset %#x)\n",
201 ctrl & reset);
202 return false;
203 }
204
205 return true;
206 }
207
dw_mci_wait_while_busy(struct dw_mci * host,u32 cmd_flags)208 static void dw_mci_wait_while_busy(struct dw_mci *host, u32 cmd_flags)
209 {
210 u32 status;
211
212 /*
213 * Databook says that before issuing a new data transfer command
214 * we need to check to see if the card is busy. Data transfer commands
215 * all have SDMMC_CMD_PRV_DAT_WAIT set, so we'll key off that.
216 *
217 * ...also allow sending for SDMMC_CMD_VOLT_SWITCH where busy is
218 * expected.
219 */
220 if ((cmd_flags & SDMMC_CMD_PRV_DAT_WAIT) &&
221 !(cmd_flags & SDMMC_CMD_VOLT_SWITCH)) {
222 if (readl_poll_timeout_atomic(host->regs + SDMMC_STATUS,
223 status,
224 !(status & SDMMC_STATUS_BUSY),
225 10, 500 * USEC_PER_MSEC))
226 dev_err(host->dev, "Busy; trying anyway\n");
227 }
228 }
229
mci_send_cmd(struct dw_mci_slot * slot,u32 cmd,u32 arg)230 static void mci_send_cmd(struct dw_mci_slot *slot, u32 cmd, u32 arg)
231 {
232 struct dw_mci *host = slot->host;
233 unsigned int cmd_status = 0;
234
235 mci_writel(host, CMDARG, arg);
236 wmb(); /* drain writebuffer */
237 dw_mci_wait_while_busy(host, cmd);
238 mci_writel(host, CMD, SDMMC_CMD_START | cmd);
239
240 if (readl_poll_timeout_atomic(host->regs + SDMMC_CMD, cmd_status,
241 !(cmd_status & SDMMC_CMD_START),
242 1, 500 * USEC_PER_MSEC))
243 dev_err(&slot->mmc->class_dev,
244 "Timeout sending command (cmd %#x arg %#x status %#x)\n",
245 cmd, arg, cmd_status);
246 }
247
dw_mci_prepare_command(struct mmc_host * mmc,struct mmc_command * cmd)248 static u32 dw_mci_prepare_command(struct mmc_host *mmc, struct mmc_command *cmd)
249 {
250 struct dw_mci_slot *slot = mmc_priv(mmc);
251 struct dw_mci *host = slot->host;
252 u32 cmdr;
253
254 cmd->error = -EINPROGRESS;
255 cmdr = cmd->opcode;
256
257 if (cmd->opcode == MMC_STOP_TRANSMISSION ||
258 cmd->opcode == MMC_GO_IDLE_STATE ||
259 cmd->opcode == MMC_GO_INACTIVE_STATE ||
260 (cmd->opcode == SD_IO_RW_DIRECT &&
261 ((cmd->arg >> 9) & 0x1FFFF) == SDIO_CCCR_ABORT))
262 cmdr |= SDMMC_CMD_STOP;
263 else if (cmd->opcode != MMC_SEND_STATUS && cmd->data)
264 cmdr |= SDMMC_CMD_PRV_DAT_WAIT;
265
266 if (cmd->opcode == SD_SWITCH_VOLTAGE) {
267 u32 clk_en_a;
268
269 /* Special bit makes CMD11 not die */
270 cmdr |= SDMMC_CMD_VOLT_SWITCH;
271
272 /* Change state to continue to handle CMD11 weirdness */
273 WARN_ON(slot->host->state != STATE_SENDING_CMD);
274 slot->host->state = STATE_SENDING_CMD11;
275
276 /*
277 * We need to disable low power mode (automatic clock stop)
278 * while doing voltage switch so we don't confuse the card,
279 * since stopping the clock is a specific part of the UHS
280 * voltage change dance.
281 *
282 * Note that low power mode (SDMMC_CLKEN_LOW_PWR) will be
283 * unconditionally turned back on in dw_mci_setup_bus() if it's
284 * ever called with a non-zero clock. That shouldn't happen
285 * until the voltage change is all done.
286 */
287 clk_en_a = mci_readl(host, CLKENA);
288 clk_en_a &= ~(SDMMC_CLKEN_LOW_PWR << slot->id);
289 mci_writel(host, CLKENA, clk_en_a);
290 mci_send_cmd(slot, SDMMC_CMD_UPD_CLK |
291 SDMMC_CMD_PRV_DAT_WAIT, 0);
292 }
293
294 if (cmd->flags & MMC_RSP_PRESENT) {
295 /* We expect a response, so set this bit */
296 cmdr |= SDMMC_CMD_RESP_EXP;
297 if (cmd->flags & MMC_RSP_136)
298 cmdr |= SDMMC_CMD_RESP_LONG;
299 }
300
301 if (cmd->flags & MMC_RSP_CRC)
302 cmdr |= SDMMC_CMD_RESP_CRC;
303
304 if (cmd->data) {
305 cmdr |= SDMMC_CMD_DAT_EXP;
306 if (cmd->data->flags & MMC_DATA_WRITE)
307 cmdr |= SDMMC_CMD_DAT_WR;
308 }
309
310 if (!test_bit(DW_MMC_CARD_NO_USE_HOLD, &slot->flags))
311 cmdr |= SDMMC_CMD_USE_HOLD_REG;
312
313 return cmdr;
314 }
315
dw_mci_prep_stop_abort(struct dw_mci * host,struct mmc_command * cmd)316 static u32 dw_mci_prep_stop_abort(struct dw_mci *host, struct mmc_command *cmd)
317 {
318 struct mmc_command *stop;
319 u32 cmdr;
320
321 if (!cmd->data)
322 return 0;
323
324 stop = &host->stop_abort;
325 cmdr = cmd->opcode;
326 memset(stop, 0, sizeof(struct mmc_command));
327
328 if (cmdr == MMC_READ_SINGLE_BLOCK ||
329 cmdr == MMC_READ_MULTIPLE_BLOCK ||
330 cmdr == MMC_WRITE_BLOCK ||
331 cmdr == MMC_WRITE_MULTIPLE_BLOCK ||
332 cmdr == MMC_SEND_TUNING_BLOCK ||
333 cmdr == MMC_SEND_TUNING_BLOCK_HS200) {
334 stop->opcode = MMC_STOP_TRANSMISSION;
335 stop->arg = 0;
336 stop->flags = MMC_RSP_R1B | MMC_CMD_AC;
337 } else if (cmdr == SD_IO_RW_EXTENDED) {
338 stop->opcode = SD_IO_RW_DIRECT;
339 stop->arg |= (1 << 31) | (0 << 28) | (SDIO_CCCR_ABORT << 9) |
340 ((cmd->arg >> 28) & 0x7);
341 stop->flags = MMC_RSP_SPI_R5 | MMC_RSP_R5 | MMC_CMD_AC;
342 } else {
343 return 0;
344 }
345
346 cmdr = stop->opcode | SDMMC_CMD_STOP |
347 SDMMC_CMD_RESP_CRC | SDMMC_CMD_RESP_EXP;
348
349 if (!test_bit(DW_MMC_CARD_NO_USE_HOLD, &host->slot->flags))
350 cmdr |= SDMMC_CMD_USE_HOLD_REG;
351
352 return cmdr;
353 }
354
dw_mci_set_cto(struct dw_mci * host)355 static inline void dw_mci_set_cto(struct dw_mci *host)
356 {
357 unsigned int cto_clks;
358 unsigned int cto_div;
359 unsigned int cto_ms;
360 unsigned long irqflags;
361
362 cto_clks = mci_readl(host, TMOUT) & 0xff;
363 cto_div = (mci_readl(host, CLKDIV) & 0xff) * 2;
364 if (cto_div == 0)
365 cto_div = 1;
366
367 cto_ms = DIV_ROUND_UP_ULL((u64)MSEC_PER_SEC * cto_clks * cto_div,
368 host->bus_hz);
369
370 /* add a bit spare time */
371 cto_ms += 10;
372
373 /*
374 * The durations we're working with are fairly short so we have to be
375 * extra careful about synchronization here. Specifically in hardware a
376 * command timeout is _at most_ 5.1 ms, so that means we expect an
377 * interrupt (either command done or timeout) to come rather quickly
378 * after the mci_writel. ...but just in case we have a long interrupt
379 * latency let's add a bit of paranoia.
380 *
381 * In general we'll assume that at least an interrupt will be asserted
382 * in hardware by the time the cto_timer runs. ...and if it hasn't
383 * been asserted in hardware by that time then we'll assume it'll never
384 * come.
385 */
386 spin_lock_irqsave(&host->irq_lock, irqflags);
387 if (!test_bit(EVENT_CMD_COMPLETE, &host->pending_events))
388 mod_timer(&host->cto_timer,
389 jiffies + msecs_to_jiffies(cto_ms) + 1);
390 spin_unlock_irqrestore(&host->irq_lock, irqflags);
391 }
392
dw_mci_start_command(struct dw_mci * host,struct mmc_command * cmd,u32 cmd_flags)393 static void dw_mci_start_command(struct dw_mci *host,
394 struct mmc_command *cmd, u32 cmd_flags)
395 {
396 host->cmd = cmd;
397 dev_vdbg(host->dev,
398 "start command: ARGR=0x%08x CMDR=0x%08x\n",
399 cmd->arg, cmd_flags);
400
401 mci_writel(host, CMDARG, cmd->arg);
402 wmb(); /* drain writebuffer */
403 dw_mci_wait_while_busy(host, cmd_flags);
404
405 mci_writel(host, CMD, cmd_flags | SDMMC_CMD_START);
406
407 /* response expected command only */
408 if (cmd_flags & SDMMC_CMD_RESP_EXP)
409 dw_mci_set_cto(host);
410 }
411
send_stop_abort(struct dw_mci * host,struct mmc_data * data)412 static inline void send_stop_abort(struct dw_mci *host, struct mmc_data *data)
413 {
414 struct mmc_command *stop = &host->stop_abort;
415
416 dw_mci_start_command(host, stop, host->stop_cmdr);
417 }
418
419 /* DMA interface functions */
dw_mci_stop_dma(struct dw_mci * host)420 static void dw_mci_stop_dma(struct dw_mci *host)
421 {
422 if (host->using_dma) {
423 host->dma_ops->stop(host);
424 host->dma_ops->cleanup(host);
425 }
426
427 /* Data transfer was stopped by the interrupt handler */
428 set_bit(EVENT_XFER_COMPLETE, &host->pending_events);
429 }
430
dw_mci_dma_cleanup(struct dw_mci * host)431 static void dw_mci_dma_cleanup(struct dw_mci *host)
432 {
433 struct mmc_data *data = host->data;
434
435 if (data && data->host_cookie == COOKIE_MAPPED) {
436 dma_unmap_sg(host->dev,
437 data->sg,
438 data->sg_len,
439 mmc_get_dma_dir(data));
440 data->host_cookie = COOKIE_UNMAPPED;
441 }
442 }
443
dw_mci_idmac_reset(struct dw_mci * host)444 static void dw_mci_idmac_reset(struct dw_mci *host)
445 {
446 u32 bmod = mci_readl(host, BMOD);
447 /* Software reset of DMA */
448 bmod |= SDMMC_IDMAC_SWRESET;
449 mci_writel(host, BMOD, bmod);
450 }
451
dw_mci_idmac_stop_dma(struct dw_mci * host)452 static void dw_mci_idmac_stop_dma(struct dw_mci *host)
453 {
454 u32 temp;
455
456 /* Disable and reset the IDMAC interface */
457 temp = mci_readl(host, CTRL);
458 temp &= ~SDMMC_CTRL_USE_IDMAC;
459 temp |= SDMMC_CTRL_DMA_RESET;
460 mci_writel(host, CTRL, temp);
461
462 /* Stop the IDMAC running */
463 temp = mci_readl(host, BMOD);
464 temp &= ~(SDMMC_IDMAC_ENABLE | SDMMC_IDMAC_FB);
465 temp |= SDMMC_IDMAC_SWRESET;
466 mci_writel(host, BMOD, temp);
467 }
468
dw_mci_dmac_complete_dma(void * arg)469 static void dw_mci_dmac_complete_dma(void *arg)
470 {
471 struct dw_mci *host = arg;
472 struct mmc_data *data = host->data;
473
474 dev_vdbg(host->dev, "DMA complete\n");
475
476 if ((host->use_dma == TRANS_MODE_EDMAC) &&
477 data && (data->flags & MMC_DATA_READ))
478 /* Invalidate cache after read */
479 dma_sync_sg_for_cpu(mmc_dev(host->slot->mmc),
480 data->sg,
481 data->sg_len,
482 DMA_FROM_DEVICE);
483
484 host->dma_ops->cleanup(host);
485
486 /*
487 * If the card was removed, data will be NULL. No point in trying to
488 * send the stop command or waiting for NBUSY in this case.
489 */
490 if (data) {
491 set_bit(EVENT_XFER_COMPLETE, &host->pending_events);
492 tasklet_schedule(&host->tasklet);
493 }
494 }
495
dw_mci_idmac_init(struct dw_mci * host)496 static int dw_mci_idmac_init(struct dw_mci *host)
497 {
498 int i;
499
500 if (host->dma_64bit_address == 1) {
501 struct idmac_desc_64addr *p;
502 /* Number of descriptors in the ring buffer */
503 host->ring_size =
504 DESC_RING_BUF_SZ / sizeof(struct idmac_desc_64addr);
505
506 /* Forward link the descriptor list */
507 for (i = 0, p = host->sg_cpu; i < host->ring_size - 1;
508 i++, p++) {
509 p->des6 = (host->sg_dma +
510 (sizeof(struct idmac_desc_64addr) *
511 (i + 1))) & 0xffffffff;
512
513 p->des7 = (u64)(host->sg_dma +
514 (sizeof(struct idmac_desc_64addr) *
515 (i + 1))) >> 32;
516 /* Initialize reserved and buffer size fields to "0" */
517 p->des0 = 0;
518 p->des1 = 0;
519 p->des2 = 0;
520 p->des3 = 0;
521 }
522
523 /* Set the last descriptor as the end-of-ring descriptor */
524 p->des6 = host->sg_dma & 0xffffffff;
525 p->des7 = (u64)host->sg_dma >> 32;
526 p->des0 = IDMAC_DES0_ER;
527
528 } else {
529 struct idmac_desc *p;
530 /* Number of descriptors in the ring buffer */
531 host->ring_size =
532 DESC_RING_BUF_SZ / sizeof(struct idmac_desc);
533
534 /* Forward link the descriptor list */
535 for (i = 0, p = host->sg_cpu;
536 i < host->ring_size - 1;
537 i++, p++) {
538 p->des3 = cpu_to_le32(host->sg_dma +
539 (sizeof(struct idmac_desc) * (i + 1)));
540 p->des0 = 0;
541 p->des1 = 0;
542 }
543
544 /* Set the last descriptor as the end-of-ring descriptor */
545 p->des3 = cpu_to_le32(host->sg_dma);
546 p->des0 = cpu_to_le32(IDMAC_DES0_ER);
547 }
548
549 dw_mci_idmac_reset(host);
550
551 if (host->dma_64bit_address == 1) {
552 /* Mask out interrupts - get Tx & Rx complete only */
553 mci_writel(host, IDSTS64, IDMAC_INT_CLR);
554 mci_writel(host, IDINTEN64, SDMMC_IDMAC_INT_NI |
555 SDMMC_IDMAC_INT_RI | SDMMC_IDMAC_INT_TI);
556
557 /* Set the descriptor base address */
558 mci_writel(host, DBADDRL, host->sg_dma & 0xffffffff);
559 mci_writel(host, DBADDRU, (u64)host->sg_dma >> 32);
560
561 } else {
562 /* Mask out interrupts - get Tx & Rx complete only */
563 mci_writel(host, IDSTS, IDMAC_INT_CLR);
564 mci_writel(host, IDINTEN, SDMMC_IDMAC_INT_NI |
565 SDMMC_IDMAC_INT_RI | SDMMC_IDMAC_INT_TI);
566
567 /* Set the descriptor base address */
568 mci_writel(host, DBADDR, host->sg_dma);
569 }
570
571 return 0;
572 }
573
dw_mci_prepare_desc64(struct dw_mci * host,struct mmc_data * data,unsigned int sg_len)574 static inline int dw_mci_prepare_desc64(struct dw_mci *host,
575 struct mmc_data *data,
576 unsigned int sg_len)
577 {
578 unsigned int desc_len;
579 struct idmac_desc_64addr *desc_first, *desc_last, *desc;
580 u32 val;
581 int i;
582
583 desc_first = desc_last = desc = host->sg_cpu;
584
585 for (i = 0; i < sg_len; i++) {
586 unsigned int length = sg_dma_len(&data->sg[i]);
587
588 u64 mem_addr = sg_dma_address(&data->sg[i]);
589
590 for ( ; length ; desc++) {
591 desc_len = (length <= DW_MCI_DESC_DATA_LENGTH) ?
592 length : DW_MCI_DESC_DATA_LENGTH;
593
594 length -= desc_len;
595
596 /*
597 * Wait for the former clear OWN bit operation
598 * of IDMAC to make sure that this descriptor
599 * isn't still owned by IDMAC as IDMAC's write
600 * ops and CPU's read ops are asynchronous.
601 */
602 if (readl_poll_timeout_atomic(&desc->des0, val,
603 !(val & IDMAC_DES0_OWN),
604 10, 100 * USEC_PER_MSEC))
605 goto err_own_bit;
606
607 /*
608 * Set the OWN bit and disable interrupts
609 * for this descriptor
610 */
611 desc->des0 = IDMAC_DES0_OWN | IDMAC_DES0_DIC |
612 IDMAC_DES0_CH;
613
614 /* Buffer length */
615 IDMAC_64ADDR_SET_BUFFER1_SIZE(desc, desc_len);
616
617 /* Physical address to DMA to/from */
618 desc->des4 = mem_addr & 0xffffffff;
619 desc->des5 = mem_addr >> 32;
620
621 /* Update physical address for the next desc */
622 mem_addr += desc_len;
623
624 /* Save pointer to the last descriptor */
625 desc_last = desc;
626 }
627 }
628
629 /* Set first descriptor */
630 desc_first->des0 |= IDMAC_DES0_FD;
631
632 /* Set last descriptor */
633 desc_last->des0 &= ~(IDMAC_DES0_CH | IDMAC_DES0_DIC);
634 desc_last->des0 |= IDMAC_DES0_LD;
635
636 return 0;
637 err_own_bit:
638 /* restore the descriptor chain as it's polluted */
639 dev_dbg(host->dev, "descriptor is still owned by IDMAC.\n");
640 memset(host->sg_cpu, 0, DESC_RING_BUF_SZ);
641 dw_mci_idmac_init(host);
642 return -EINVAL;
643 }
644
645
dw_mci_prepare_desc32(struct dw_mci * host,struct mmc_data * data,unsigned int sg_len)646 static inline int dw_mci_prepare_desc32(struct dw_mci *host,
647 struct mmc_data *data,
648 unsigned int sg_len)
649 {
650 unsigned int desc_len;
651 struct idmac_desc *desc_first, *desc_last, *desc;
652 u32 val;
653 int i;
654
655 desc_first = desc_last = desc = host->sg_cpu;
656
657 for (i = 0; i < sg_len; i++) {
658 unsigned int length = sg_dma_len(&data->sg[i]);
659
660 u32 mem_addr = sg_dma_address(&data->sg[i]);
661
662 for ( ; length ; desc++) {
663 desc_len = (length <= DW_MCI_DESC_DATA_LENGTH) ?
664 length : DW_MCI_DESC_DATA_LENGTH;
665
666 length -= desc_len;
667
668 /*
669 * Wait for the former clear OWN bit operation
670 * of IDMAC to make sure that this descriptor
671 * isn't still owned by IDMAC as IDMAC's write
672 * ops and CPU's read ops are asynchronous.
673 */
674 if (readl_poll_timeout_atomic(&desc->des0, val,
675 IDMAC_OWN_CLR64(val),
676 10,
677 100 * USEC_PER_MSEC))
678 goto err_own_bit;
679
680 /*
681 * Set the OWN bit and disable interrupts
682 * for this descriptor
683 */
684 desc->des0 = cpu_to_le32(IDMAC_DES0_OWN |
685 IDMAC_DES0_DIC |
686 IDMAC_DES0_CH);
687
688 /* Buffer length */
689 IDMAC_SET_BUFFER1_SIZE(desc, desc_len);
690
691 /* Physical address to DMA to/from */
692 desc->des2 = cpu_to_le32(mem_addr);
693
694 /* Update physical address for the next desc */
695 mem_addr += desc_len;
696
697 /* Save pointer to the last descriptor */
698 desc_last = desc;
699 }
700 }
701
702 /* Set first descriptor */
703 desc_first->des0 |= cpu_to_le32(IDMAC_DES0_FD);
704
705 /* Set last descriptor */
706 desc_last->des0 &= cpu_to_le32(~(IDMAC_DES0_CH |
707 IDMAC_DES0_DIC));
708 desc_last->des0 |= cpu_to_le32(IDMAC_DES0_LD);
709
710 return 0;
711 err_own_bit:
712 /* restore the descriptor chain as it's polluted */
713 dev_dbg(host->dev, "descriptor is still owned by IDMAC.\n");
714 memset(host->sg_cpu, 0, DESC_RING_BUF_SZ);
715 dw_mci_idmac_init(host);
716 return -EINVAL;
717 }
718
dw_mci_idmac_start_dma(struct dw_mci * host,unsigned int sg_len)719 static int dw_mci_idmac_start_dma(struct dw_mci *host, unsigned int sg_len)
720 {
721 u32 temp;
722 int ret;
723
724 if (host->dma_64bit_address == 1)
725 ret = dw_mci_prepare_desc64(host, host->data, sg_len);
726 else
727 ret = dw_mci_prepare_desc32(host, host->data, sg_len);
728
729 if (ret)
730 goto out;
731
732 /* drain writebuffer */
733 wmb();
734
735 /* Make sure to reset DMA in case we did PIO before this */
736 dw_mci_ctrl_reset(host, SDMMC_CTRL_DMA_RESET);
737 dw_mci_idmac_reset(host);
738
739 /* Select IDMAC interface */
740 temp = mci_readl(host, CTRL);
741 temp |= SDMMC_CTRL_USE_IDMAC;
742 mci_writel(host, CTRL, temp);
743
744 /* drain writebuffer */
745 wmb();
746
747 /* Enable the IDMAC */
748 temp = mci_readl(host, BMOD);
749 temp |= SDMMC_IDMAC_ENABLE | SDMMC_IDMAC_FB;
750 mci_writel(host, BMOD, temp);
751
752 /* Start it running */
753 mci_writel(host, PLDMND, 1);
754
755 out:
756 return ret;
757 }
758
759 static const struct dw_mci_dma_ops dw_mci_idmac_ops = {
760 .init = dw_mci_idmac_init,
761 .start = dw_mci_idmac_start_dma,
762 .stop = dw_mci_idmac_stop_dma,
763 .complete = dw_mci_dmac_complete_dma,
764 .cleanup = dw_mci_dma_cleanup,
765 };
766
dw_mci_edmac_stop_dma(struct dw_mci * host)767 static void dw_mci_edmac_stop_dma(struct dw_mci *host)
768 {
769 dmaengine_terminate_async(host->dms->ch);
770 }
771
dw_mci_edmac_start_dma(struct dw_mci * host,unsigned int sg_len)772 static int dw_mci_edmac_start_dma(struct dw_mci *host,
773 unsigned int sg_len)
774 {
775 struct dma_slave_config cfg;
776 struct dma_async_tx_descriptor *desc = NULL;
777 struct scatterlist *sgl = host->data->sg;
778 static const u32 mszs[] = {1, 4, 8, 16, 32, 64, 128, 256};
779 u32 sg_elems = host->data->sg_len;
780 u32 fifoth_val;
781 u32 fifo_offset = host->fifo_reg - host->regs;
782 int ret = 0;
783
784 /* Set external dma config: burst size, burst width */
785 cfg.dst_addr = host->phy_regs + fifo_offset;
786 cfg.src_addr = cfg.dst_addr;
787 cfg.dst_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES;
788 cfg.src_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES;
789
790 /* Match burst msize with external dma config */
791 fifoth_val = mci_readl(host, FIFOTH);
792 cfg.dst_maxburst = mszs[(fifoth_val >> 28) & 0x7];
793 cfg.src_maxburst = cfg.dst_maxburst;
794
795 if (host->data->flags & MMC_DATA_WRITE)
796 cfg.direction = DMA_MEM_TO_DEV;
797 else
798 cfg.direction = DMA_DEV_TO_MEM;
799
800 ret = dmaengine_slave_config(host->dms->ch, &cfg);
801 if (ret) {
802 dev_err(host->dev, "Failed to config edmac.\n");
803 return -EBUSY;
804 }
805
806 desc = dmaengine_prep_slave_sg(host->dms->ch, sgl,
807 sg_len, cfg.direction,
808 DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
809 if (!desc) {
810 dev_err(host->dev, "Can't prepare slave sg.\n");
811 return -EBUSY;
812 }
813
814 /* Set dw_mci_dmac_complete_dma as callback */
815 desc->callback = dw_mci_dmac_complete_dma;
816 desc->callback_param = (void *)host;
817 dmaengine_submit(desc);
818
819 /* Flush cache before write */
820 if (host->data->flags & MMC_DATA_WRITE)
821 dma_sync_sg_for_device(mmc_dev(host->slot->mmc), sgl,
822 sg_elems, DMA_TO_DEVICE);
823
824 dma_async_issue_pending(host->dms->ch);
825
826 return 0;
827 }
828
dw_mci_edmac_init(struct dw_mci * host)829 static int dw_mci_edmac_init(struct dw_mci *host)
830 {
831 /* Request external dma channel */
832 host->dms = kzalloc(sizeof(struct dw_mci_dma_slave), GFP_KERNEL);
833 if (!host->dms)
834 return -ENOMEM;
835
836 host->dms->ch = dma_request_chan(host->dev, "rx-tx");
837 if (IS_ERR(host->dms->ch)) {
838 int ret = PTR_ERR(host->dms->ch);
839
840 dev_err(host->dev, "Failed to get external DMA channel.\n");
841 kfree(host->dms);
842 host->dms = NULL;
843 return ret;
844 }
845
846 return 0;
847 }
848
dw_mci_edmac_exit(struct dw_mci * host)849 static void dw_mci_edmac_exit(struct dw_mci *host)
850 {
851 if (host->dms) {
852 if (host->dms->ch) {
853 dma_release_channel(host->dms->ch);
854 host->dms->ch = NULL;
855 }
856 kfree(host->dms);
857 host->dms = NULL;
858 }
859 }
860
861 static const struct dw_mci_dma_ops dw_mci_edmac_ops = {
862 .init = dw_mci_edmac_init,
863 .exit = dw_mci_edmac_exit,
864 .start = dw_mci_edmac_start_dma,
865 .stop = dw_mci_edmac_stop_dma,
866 .complete = dw_mci_dmac_complete_dma,
867 .cleanup = dw_mci_dma_cleanup,
868 };
869
dw_mci_pre_dma_transfer(struct dw_mci * host,struct mmc_data * data,int cookie)870 static int dw_mci_pre_dma_transfer(struct dw_mci *host,
871 struct mmc_data *data,
872 int cookie)
873 {
874 struct scatterlist *sg;
875 unsigned int i, sg_len;
876
877 if (data->host_cookie == COOKIE_PRE_MAPPED)
878 return data->sg_len;
879
880 /*
881 * We don't do DMA on "complex" transfers, i.e. with
882 * non-word-aligned buffers or lengths. Also, we don't bother
883 * with all the DMA setup overhead for short transfers.
884 */
885 if (data->blocks * data->blksz < DW_MCI_DMA_THRESHOLD)
886 return -EINVAL;
887
888 if (data->blksz & 3)
889 return -EINVAL;
890
891 for_each_sg(data->sg, sg, data->sg_len, i) {
892 if (sg->offset & 3 || sg->length & 3)
893 return -EINVAL;
894 }
895
896 sg_len = dma_map_sg(host->dev,
897 data->sg,
898 data->sg_len,
899 mmc_get_dma_dir(data));
900 if (sg_len == 0)
901 return -EINVAL;
902
903 data->host_cookie = cookie;
904
905 return sg_len;
906 }
907
dw_mci_pre_req(struct mmc_host * mmc,struct mmc_request * mrq)908 static void dw_mci_pre_req(struct mmc_host *mmc,
909 struct mmc_request *mrq)
910 {
911 struct dw_mci_slot *slot = mmc_priv(mmc);
912 struct mmc_data *data = mrq->data;
913
914 if (!slot->host->use_dma || !data)
915 return;
916
917 /* This data might be unmapped at this time */
918 data->host_cookie = COOKIE_UNMAPPED;
919
920 if (dw_mci_pre_dma_transfer(slot->host, mrq->data,
921 COOKIE_PRE_MAPPED) < 0)
922 data->host_cookie = COOKIE_UNMAPPED;
923 }
924
dw_mci_post_req(struct mmc_host * mmc,struct mmc_request * mrq,int err)925 static void dw_mci_post_req(struct mmc_host *mmc,
926 struct mmc_request *mrq,
927 int err)
928 {
929 struct dw_mci_slot *slot = mmc_priv(mmc);
930 struct mmc_data *data = mrq->data;
931
932 if (!slot->host->use_dma || !data)
933 return;
934
935 if (data->host_cookie != COOKIE_UNMAPPED)
936 dma_unmap_sg(slot->host->dev,
937 data->sg,
938 data->sg_len,
939 mmc_get_dma_dir(data));
940 data->host_cookie = COOKIE_UNMAPPED;
941 }
942
dw_mci_get_cd(struct mmc_host * mmc)943 static int dw_mci_get_cd(struct mmc_host *mmc)
944 {
945 int present;
946 struct dw_mci_slot *slot = mmc_priv(mmc);
947 struct dw_mci *host = slot->host;
948 int gpio_cd = mmc_gpio_get_cd(mmc);
949
950 /* Use platform get_cd function, else try onboard card detect */
951 if (((mmc->caps & MMC_CAP_NEEDS_POLL)
952 || !mmc_card_is_removable(mmc))) {
953 present = 1;
954
955 if (!test_bit(DW_MMC_CARD_PRESENT, &slot->flags)) {
956 if (mmc->caps & MMC_CAP_NEEDS_POLL) {
957 dev_info(&mmc->class_dev,
958 "card is polling.\n");
959 } else {
960 dev_info(&mmc->class_dev,
961 "card is non-removable.\n");
962 }
963 set_bit(DW_MMC_CARD_PRESENT, &slot->flags);
964 }
965
966 return present;
967 } else if (gpio_cd >= 0)
968 present = gpio_cd;
969 else
970 present = (mci_readl(slot->host, CDETECT) & (1 << slot->id))
971 == 0 ? 1 : 0;
972
973 spin_lock_bh(&host->lock);
974 if (present && !test_and_set_bit(DW_MMC_CARD_PRESENT, &slot->flags))
975 dev_dbg(&mmc->class_dev, "card is present\n");
976 else if (!present &&
977 !test_and_clear_bit(DW_MMC_CARD_PRESENT, &slot->flags))
978 dev_dbg(&mmc->class_dev, "card is not present\n");
979 spin_unlock_bh(&host->lock);
980
981 return present;
982 }
983
dw_mci_adjust_fifoth(struct dw_mci * host,struct mmc_data * data)984 static void dw_mci_adjust_fifoth(struct dw_mci *host, struct mmc_data *data)
985 {
986 unsigned int blksz = data->blksz;
987 static const u32 mszs[] = {1, 4, 8, 16, 32, 64, 128, 256};
988 u32 fifo_width = 1 << host->data_shift;
989 u32 blksz_depth = blksz / fifo_width, fifoth_val;
990 u32 msize = 0, rx_wmark = 1, tx_wmark, tx_wmark_invers;
991 int idx = ARRAY_SIZE(mszs) - 1;
992
993 /* pio should ship this scenario */
994 if (!host->use_dma)
995 return;
996
997 tx_wmark = (host->fifo_depth) / 2;
998 tx_wmark_invers = host->fifo_depth - tx_wmark;
999
1000 /*
1001 * MSIZE is '1',
1002 * if blksz is not a multiple of the FIFO width
1003 */
1004 if (blksz % fifo_width)
1005 goto done;
1006
1007 do {
1008 if (!((blksz_depth % mszs[idx]) ||
1009 (tx_wmark_invers % mszs[idx]))) {
1010 msize = idx;
1011 rx_wmark = mszs[idx] - 1;
1012 break;
1013 }
1014 } while (--idx > 0);
1015 /*
1016 * If idx is '0', it won't be tried
1017 * Thus, initial values are uesed
1018 */
1019 done:
1020 fifoth_val = SDMMC_SET_FIFOTH(msize, rx_wmark, tx_wmark);
1021 mci_writel(host, FIFOTH, fifoth_val);
1022 }
1023
dw_mci_ctrl_thld(struct dw_mci * host,struct mmc_data * data)1024 static void dw_mci_ctrl_thld(struct dw_mci *host, struct mmc_data *data)
1025 {
1026 unsigned int blksz = data->blksz;
1027 u32 blksz_depth, fifo_depth;
1028 u16 thld_size;
1029 u8 enable;
1030
1031 /*
1032 * CDTHRCTL doesn't exist prior to 240A (in fact that register offset is
1033 * in the FIFO region, so we really shouldn't access it).
1034 */
1035 if (host->verid < DW_MMC_240A ||
1036 (host->verid < DW_MMC_280A && data->flags & MMC_DATA_WRITE))
1037 return;
1038
1039 /*
1040 * Card write Threshold is introduced since 2.80a
1041 * It's used when HS400 mode is enabled.
1042 */
1043 if (data->flags & MMC_DATA_WRITE &&
1044 host->timing != MMC_TIMING_MMC_HS400)
1045 goto disable;
1046
1047 if (data->flags & MMC_DATA_WRITE)
1048 enable = SDMMC_CARD_WR_THR_EN;
1049 else
1050 enable = SDMMC_CARD_RD_THR_EN;
1051
1052 if (host->timing != MMC_TIMING_MMC_HS200 &&
1053 host->timing != MMC_TIMING_UHS_SDR104 &&
1054 host->timing != MMC_TIMING_MMC_HS400)
1055 goto disable;
1056
1057 blksz_depth = blksz / (1 << host->data_shift);
1058 fifo_depth = host->fifo_depth;
1059
1060 if (blksz_depth > fifo_depth)
1061 goto disable;
1062
1063 /*
1064 * If (blksz_depth) >= (fifo_depth >> 1), should be 'thld_size <= blksz'
1065 * If (blksz_depth) < (fifo_depth >> 1), should be thld_size = blksz
1066 * Currently just choose blksz.
1067 */
1068 thld_size = blksz;
1069 mci_writel(host, CDTHRCTL, SDMMC_SET_THLD(thld_size, enable));
1070 return;
1071
1072 disable:
1073 mci_writel(host, CDTHRCTL, 0);
1074 }
1075
dw_mci_submit_data_dma(struct dw_mci * host,struct mmc_data * data)1076 static int dw_mci_submit_data_dma(struct dw_mci *host, struct mmc_data *data)
1077 {
1078 unsigned long irqflags;
1079 int sg_len;
1080 u32 temp;
1081
1082 host->using_dma = 0;
1083
1084 /* If we don't have a channel, we can't do DMA */
1085 if (!host->use_dma)
1086 return -ENODEV;
1087
1088 sg_len = dw_mci_pre_dma_transfer(host, data, COOKIE_MAPPED);
1089 if (sg_len < 0) {
1090 host->dma_ops->stop(host);
1091 return sg_len;
1092 }
1093
1094 host->using_dma = 1;
1095
1096 if (host->use_dma == TRANS_MODE_IDMAC)
1097 dev_vdbg(host->dev,
1098 "sd sg_cpu: %#lx sg_dma: %#lx sg_len: %d\n",
1099 (unsigned long)host->sg_cpu,
1100 (unsigned long)host->sg_dma,
1101 sg_len);
1102
1103 /*
1104 * Decide the MSIZE and RX/TX Watermark.
1105 * If current block size is same with previous size,
1106 * no need to update fifoth.
1107 */
1108 if (host->prev_blksz != data->blksz)
1109 dw_mci_adjust_fifoth(host, data);
1110
1111 /* Enable the DMA interface */
1112 temp = mci_readl(host, CTRL);
1113 temp |= SDMMC_CTRL_DMA_ENABLE;
1114 mci_writel(host, CTRL, temp);
1115
1116 /* Disable RX/TX IRQs, let DMA handle it */
1117 spin_lock_irqsave(&host->irq_lock, irqflags);
1118 temp = mci_readl(host, INTMASK);
1119 temp &= ~(SDMMC_INT_RXDR | SDMMC_INT_TXDR);
1120 mci_writel(host, INTMASK, temp);
1121 spin_unlock_irqrestore(&host->irq_lock, irqflags);
1122
1123 if (host->dma_ops->start(host, sg_len)) {
1124 host->dma_ops->stop(host);
1125 /* We can't do DMA, try PIO for this one */
1126 dev_dbg(host->dev,
1127 "%s: fall back to PIO mode for current transfer\n",
1128 __func__);
1129 return -ENODEV;
1130 }
1131
1132 return 0;
1133 }
1134
dw_mci_submit_data(struct dw_mci * host,struct mmc_data * data)1135 static void dw_mci_submit_data(struct dw_mci *host, struct mmc_data *data)
1136 {
1137 unsigned long irqflags;
1138 int flags = SG_MITER_ATOMIC;
1139 u32 temp;
1140
1141 data->error = -EINPROGRESS;
1142
1143 WARN_ON(host->data);
1144 host->sg = NULL;
1145 host->data = data;
1146
1147 if (data->flags & MMC_DATA_READ)
1148 host->dir_status = DW_MCI_RECV_STATUS;
1149 else
1150 host->dir_status = DW_MCI_SEND_STATUS;
1151
1152 dw_mci_ctrl_thld(host, data);
1153
1154 if (dw_mci_submit_data_dma(host, data)) {
1155 if (host->data->flags & MMC_DATA_READ)
1156 flags |= SG_MITER_TO_SG;
1157 else
1158 flags |= SG_MITER_FROM_SG;
1159
1160 sg_miter_start(&host->sg_miter, data->sg, data->sg_len, flags);
1161 host->sg = data->sg;
1162 host->part_buf_start = 0;
1163 host->part_buf_count = 0;
1164
1165 mci_writel(host, RINTSTS, SDMMC_INT_TXDR | SDMMC_INT_RXDR);
1166
1167 spin_lock_irqsave(&host->irq_lock, irqflags);
1168 temp = mci_readl(host, INTMASK);
1169 temp |= SDMMC_INT_TXDR | SDMMC_INT_RXDR;
1170 mci_writel(host, INTMASK, temp);
1171 spin_unlock_irqrestore(&host->irq_lock, irqflags);
1172
1173 temp = mci_readl(host, CTRL);
1174 temp &= ~SDMMC_CTRL_DMA_ENABLE;
1175 mci_writel(host, CTRL, temp);
1176
1177 /*
1178 * Use the initial fifoth_val for PIO mode. If wm_algined
1179 * is set, we set watermark same as data size.
1180 * If next issued data may be transfered by DMA mode,
1181 * prev_blksz should be invalidated.
1182 */
1183 if (host->wm_aligned)
1184 dw_mci_adjust_fifoth(host, data);
1185 else
1186 mci_writel(host, FIFOTH, host->fifoth_val);
1187 host->prev_blksz = 0;
1188 } else {
1189 /*
1190 * Keep the current block size.
1191 * It will be used to decide whether to update
1192 * fifoth register next time.
1193 */
1194 host->prev_blksz = data->blksz;
1195 }
1196 }
1197
dw_mci_setup_bus(struct dw_mci_slot * slot,bool force_clkinit)1198 static void dw_mci_setup_bus(struct dw_mci_slot *slot, bool force_clkinit)
1199 {
1200 struct dw_mci *host = slot->host;
1201 unsigned int clock = slot->clock;
1202 u32 div;
1203 u32 clk_en_a;
1204 u32 sdmmc_cmd_bits = SDMMC_CMD_UPD_CLK | SDMMC_CMD_PRV_DAT_WAIT;
1205
1206 /* We must continue to set bit 28 in CMD until the change is complete */
1207 if (host->state == STATE_WAITING_CMD11_DONE)
1208 sdmmc_cmd_bits |= SDMMC_CMD_VOLT_SWITCH;
1209
1210 slot->mmc->actual_clock = 0;
1211
1212 if (!clock) {
1213 mci_writel(host, CLKENA, 0);
1214 mci_send_cmd(slot, sdmmc_cmd_bits, 0);
1215 } else if (clock != host->current_speed || force_clkinit) {
1216 div = host->bus_hz / clock;
1217 if (host->bus_hz % clock && host->bus_hz > clock)
1218 /*
1219 * move the + 1 after the divide to prevent
1220 * over-clocking the card.
1221 */
1222 div += 1;
1223
1224 div = (host->bus_hz != clock) ? DIV_ROUND_UP(div, 2) : 0;
1225
1226 if ((clock != slot->__clk_old &&
1227 !test_bit(DW_MMC_CARD_NEEDS_POLL, &slot->flags)) ||
1228 force_clkinit) {
1229 /* Silent the verbose log if calling from PM context */
1230 if (!force_clkinit)
1231 dev_info(&slot->mmc->class_dev,
1232 "Bus speed (slot %d) = %dHz (slot req %dHz, actual %dHZ div = %d)\n",
1233 slot->id, host->bus_hz, clock,
1234 div ? ((host->bus_hz / div) >> 1) :
1235 host->bus_hz, div);
1236
1237 /*
1238 * If card is polling, display the message only
1239 * one time at boot time.
1240 */
1241 if (slot->mmc->caps & MMC_CAP_NEEDS_POLL &&
1242 slot->mmc->f_min == clock)
1243 set_bit(DW_MMC_CARD_NEEDS_POLL, &slot->flags);
1244 }
1245
1246 /* disable clock */
1247 mci_writel(host, CLKENA, 0);
1248 mci_writel(host, CLKSRC, 0);
1249
1250 /* inform CIU */
1251 mci_send_cmd(slot, sdmmc_cmd_bits, 0);
1252
1253 /* set clock to desired speed */
1254 mci_writel(host, CLKDIV, div);
1255
1256 /* inform CIU */
1257 mci_send_cmd(slot, sdmmc_cmd_bits, 0);
1258
1259 /* enable clock; only low power if no SDIO */
1260 clk_en_a = SDMMC_CLKEN_ENABLE << slot->id;
1261 if (!test_bit(DW_MMC_CARD_NO_LOW_PWR, &slot->flags))
1262 clk_en_a |= SDMMC_CLKEN_LOW_PWR << slot->id;
1263 mci_writel(host, CLKENA, clk_en_a);
1264
1265 /* inform CIU */
1266 mci_send_cmd(slot, sdmmc_cmd_bits, 0);
1267
1268 /* keep the last clock value that was requested from core */
1269 slot->__clk_old = clock;
1270 slot->mmc->actual_clock = div ? ((host->bus_hz / div) >> 1) :
1271 host->bus_hz;
1272 }
1273
1274 host->current_speed = clock;
1275
1276 /* Set the current slot bus width */
1277 mci_writel(host, CTYPE, (slot->ctype << slot->id));
1278 }
1279
__dw_mci_start_request(struct dw_mci * host,struct dw_mci_slot * slot,struct mmc_command * cmd)1280 static void __dw_mci_start_request(struct dw_mci *host,
1281 struct dw_mci_slot *slot,
1282 struct mmc_command *cmd)
1283 {
1284 struct mmc_request *mrq;
1285 struct mmc_data *data;
1286 u32 cmdflags;
1287
1288 mrq = slot->mrq;
1289
1290 host->mrq = mrq;
1291
1292 host->pending_events = 0;
1293 host->completed_events = 0;
1294 host->cmd_status = 0;
1295 host->data_status = 0;
1296 host->dir_status = 0;
1297
1298 data = cmd->data;
1299 if (data) {
1300 mci_writel(host, TMOUT, 0xFFFFFFFF);
1301 mci_writel(host, BYTCNT, data->blksz*data->blocks);
1302 mci_writel(host, BLKSIZ, data->blksz);
1303 }
1304
1305 cmdflags = dw_mci_prepare_command(slot->mmc, cmd);
1306
1307 /* this is the first command, send the initialization clock */
1308 if (test_and_clear_bit(DW_MMC_CARD_NEED_INIT, &slot->flags))
1309 cmdflags |= SDMMC_CMD_INIT;
1310
1311 if (data) {
1312 dw_mci_submit_data(host, data);
1313 wmb(); /* drain writebuffer */
1314 }
1315
1316 dw_mci_start_command(host, cmd, cmdflags);
1317
1318 if (cmd->opcode == SD_SWITCH_VOLTAGE) {
1319 unsigned long irqflags;
1320
1321 /*
1322 * Databook says to fail after 2ms w/ no response, but evidence
1323 * shows that sometimes the cmd11 interrupt takes over 130ms.
1324 * We'll set to 500ms, plus an extra jiffy just in case jiffies
1325 * is just about to roll over.
1326 *
1327 * We do this whole thing under spinlock and only if the
1328 * command hasn't already completed (indicating the the irq
1329 * already ran so we don't want the timeout).
1330 */
1331 spin_lock_irqsave(&host->irq_lock, irqflags);
1332 if (!test_bit(EVENT_CMD_COMPLETE, &host->pending_events))
1333 mod_timer(&host->cmd11_timer,
1334 jiffies + msecs_to_jiffies(500) + 1);
1335 spin_unlock_irqrestore(&host->irq_lock, irqflags);
1336 }
1337
1338 host->stop_cmdr = dw_mci_prep_stop_abort(host, cmd);
1339 }
1340
dw_mci_start_request(struct dw_mci * host,struct dw_mci_slot * slot)1341 static void dw_mci_start_request(struct dw_mci *host,
1342 struct dw_mci_slot *slot)
1343 {
1344 struct mmc_request *mrq = slot->mrq;
1345 struct mmc_command *cmd;
1346
1347 cmd = mrq->sbc ? mrq->sbc : mrq->cmd;
1348 __dw_mci_start_request(host, slot, cmd);
1349 }
1350
1351 /* must be called with host->lock held */
dw_mci_queue_request(struct dw_mci * host,struct dw_mci_slot * slot,struct mmc_request * mrq)1352 static void dw_mci_queue_request(struct dw_mci *host, struct dw_mci_slot *slot,
1353 struct mmc_request *mrq)
1354 {
1355 dev_vdbg(&slot->mmc->class_dev, "queue request: state=%d\n",
1356 host->state);
1357
1358 slot->mrq = mrq;
1359
1360 if (host->state == STATE_WAITING_CMD11_DONE) {
1361 dev_warn(&slot->mmc->class_dev,
1362 "Voltage change didn't complete\n");
1363 /*
1364 * this case isn't expected to happen, so we can
1365 * either crash here or just try to continue on
1366 * in the closest possible state
1367 */
1368 host->state = STATE_IDLE;
1369 }
1370
1371 if (host->state == STATE_IDLE) {
1372 host->state = STATE_SENDING_CMD;
1373 dw_mci_start_request(host, slot);
1374 } else {
1375 list_add_tail(&slot->queue_node, &host->queue);
1376 }
1377 }
1378
dw_mci_request(struct mmc_host * mmc,struct mmc_request * mrq)1379 static void dw_mci_request(struct mmc_host *mmc, struct mmc_request *mrq)
1380 {
1381 struct dw_mci_slot *slot = mmc_priv(mmc);
1382 struct dw_mci *host = slot->host;
1383
1384 WARN_ON(slot->mrq);
1385
1386 /*
1387 * The check for card presence and queueing of the request must be
1388 * atomic, otherwise the card could be removed in between and the
1389 * request wouldn't fail until another card was inserted.
1390 */
1391
1392 if (!dw_mci_get_cd(mmc)) {
1393 mrq->cmd->error = -ENOMEDIUM;
1394 mmc_request_done(mmc, mrq);
1395 return;
1396 }
1397
1398 spin_lock_bh(&host->lock);
1399
1400 dw_mci_queue_request(host, slot, mrq);
1401
1402 spin_unlock_bh(&host->lock);
1403 }
1404
dw_mci_set_ios(struct mmc_host * mmc,struct mmc_ios * ios)1405 static void dw_mci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
1406 {
1407 struct dw_mci_slot *slot = mmc_priv(mmc);
1408 const struct dw_mci_drv_data *drv_data = slot->host->drv_data;
1409 u32 regs;
1410 int ret;
1411
1412 switch (ios->bus_width) {
1413 case MMC_BUS_WIDTH_4:
1414 slot->ctype = SDMMC_CTYPE_4BIT;
1415 break;
1416 case MMC_BUS_WIDTH_8:
1417 slot->ctype = SDMMC_CTYPE_8BIT;
1418 break;
1419 default:
1420 /* set default 1 bit mode */
1421 slot->ctype = SDMMC_CTYPE_1BIT;
1422 }
1423
1424 regs = mci_readl(slot->host, UHS_REG);
1425
1426 /* DDR mode set */
1427 if (ios->timing == MMC_TIMING_MMC_DDR52 ||
1428 ios->timing == MMC_TIMING_UHS_DDR50 ||
1429 ios->timing == MMC_TIMING_MMC_HS400)
1430 regs |= ((0x1 << slot->id) << 16);
1431 else
1432 regs &= ~((0x1 << slot->id) << 16);
1433
1434 mci_writel(slot->host, UHS_REG, regs);
1435 slot->host->timing = ios->timing;
1436
1437 /*
1438 * Use mirror of ios->clock to prevent race with mmc
1439 * core ios update when finding the minimum.
1440 */
1441 slot->clock = ios->clock;
1442
1443 if (drv_data && drv_data->set_ios)
1444 drv_data->set_ios(slot->host, ios);
1445
1446 switch (ios->power_mode) {
1447 case MMC_POWER_UP:
1448 if (!IS_ERR(mmc->supply.vmmc)) {
1449 ret = mmc_regulator_set_ocr(mmc, mmc->supply.vmmc,
1450 ios->vdd);
1451 if (ret) {
1452 dev_err(slot->host->dev,
1453 "failed to enable vmmc regulator\n");
1454 /*return, if failed turn on vmmc*/
1455 return;
1456 }
1457 }
1458 set_bit(DW_MMC_CARD_NEED_INIT, &slot->flags);
1459 regs = mci_readl(slot->host, PWREN);
1460 regs |= (1 << slot->id);
1461 mci_writel(slot->host, PWREN, regs);
1462 break;
1463 case MMC_POWER_ON:
1464 if (!slot->host->vqmmc_enabled) {
1465 if (!IS_ERR(mmc->supply.vqmmc)) {
1466 ret = regulator_enable(mmc->supply.vqmmc);
1467 if (ret < 0)
1468 dev_err(slot->host->dev,
1469 "failed to enable vqmmc\n");
1470 else
1471 slot->host->vqmmc_enabled = true;
1472
1473 } else {
1474 /* Keep track so we don't reset again */
1475 slot->host->vqmmc_enabled = true;
1476 }
1477
1478 /* Reset our state machine after powering on */
1479 dw_mci_ctrl_reset(slot->host,
1480 SDMMC_CTRL_ALL_RESET_FLAGS);
1481 }
1482
1483 /* Adjust clock / bus width after power is up */
1484 dw_mci_setup_bus(slot, false);
1485
1486 break;
1487 case MMC_POWER_OFF:
1488 /* Turn clock off before power goes down */
1489 dw_mci_setup_bus(slot, false);
1490
1491 if (!IS_ERR(mmc->supply.vmmc))
1492 mmc_regulator_set_ocr(mmc, mmc->supply.vmmc, 0);
1493
1494 if (!IS_ERR(mmc->supply.vqmmc) && slot->host->vqmmc_enabled)
1495 regulator_disable(mmc->supply.vqmmc);
1496 slot->host->vqmmc_enabled = false;
1497
1498 regs = mci_readl(slot->host, PWREN);
1499 regs &= ~(1 << slot->id);
1500 mci_writel(slot->host, PWREN, regs);
1501 break;
1502 default:
1503 break;
1504 }
1505
1506 if (slot->host->state == STATE_WAITING_CMD11_DONE && ios->clock != 0)
1507 slot->host->state = STATE_IDLE;
1508 }
1509
dw_mci_card_busy(struct mmc_host * mmc)1510 static int dw_mci_card_busy(struct mmc_host *mmc)
1511 {
1512 struct dw_mci_slot *slot = mmc_priv(mmc);
1513 u32 status;
1514
1515 /*
1516 * Check the busy bit which is low when DAT[3:0]
1517 * (the data lines) are 0000
1518 */
1519 status = mci_readl(slot->host, STATUS);
1520
1521 return !!(status & SDMMC_STATUS_BUSY);
1522 }
1523
dw_mci_switch_voltage(struct mmc_host * mmc,struct mmc_ios * ios)1524 static int dw_mci_switch_voltage(struct mmc_host *mmc, struct mmc_ios *ios)
1525 {
1526 struct dw_mci_slot *slot = mmc_priv(mmc);
1527 struct dw_mci *host = slot->host;
1528 const struct dw_mci_drv_data *drv_data = host->drv_data;
1529 u32 uhs;
1530 u32 v18 = SDMMC_UHS_18V << slot->id;
1531 int ret;
1532
1533 if (drv_data && drv_data->switch_voltage)
1534 return drv_data->switch_voltage(mmc, ios);
1535
1536 /*
1537 * Program the voltage. Note that some instances of dw_mmc may use
1538 * the UHS_REG for this. For other instances (like exynos) the UHS_REG
1539 * does no harm but you need to set the regulator directly. Try both.
1540 */
1541 uhs = mci_readl(host, UHS_REG);
1542 if (ios->signal_voltage == MMC_SIGNAL_VOLTAGE_330)
1543 uhs &= ~v18;
1544 else
1545 uhs |= v18;
1546
1547 if (!IS_ERR(mmc->supply.vqmmc)) {
1548 ret = mmc_regulator_set_vqmmc(mmc, ios);
1549 if (ret < 0) {
1550 dev_dbg(&mmc->class_dev,
1551 "Regulator set error %d - %s V\n",
1552 ret, uhs & v18 ? "1.8" : "3.3");
1553 return ret;
1554 }
1555 }
1556 mci_writel(host, UHS_REG, uhs);
1557
1558 return 0;
1559 }
1560
dw_mci_get_ro(struct mmc_host * mmc)1561 static int dw_mci_get_ro(struct mmc_host *mmc)
1562 {
1563 int read_only;
1564 struct dw_mci_slot *slot = mmc_priv(mmc);
1565 int gpio_ro = mmc_gpio_get_ro(mmc);
1566
1567 /* Use platform get_ro function, else try on board write protect */
1568 if (gpio_ro >= 0)
1569 read_only = gpio_ro;
1570 else
1571 read_only =
1572 mci_readl(slot->host, WRTPRT) & (1 << slot->id) ? 1 : 0;
1573
1574 dev_dbg(&mmc->class_dev, "card is %s\n",
1575 read_only ? "read-only" : "read-write");
1576
1577 return read_only;
1578 }
1579
dw_mci_hw_reset(struct mmc_host * mmc)1580 static void dw_mci_hw_reset(struct mmc_host *mmc)
1581 {
1582 struct dw_mci_slot *slot = mmc_priv(mmc);
1583 struct dw_mci *host = slot->host;
1584 int reset;
1585
1586 if (host->use_dma == TRANS_MODE_IDMAC)
1587 dw_mci_idmac_reset(host);
1588
1589 if (!dw_mci_ctrl_reset(host, SDMMC_CTRL_DMA_RESET |
1590 SDMMC_CTRL_FIFO_RESET))
1591 return;
1592
1593 /*
1594 * According to eMMC spec, card reset procedure:
1595 * tRstW >= 1us: RST_n pulse width
1596 * tRSCA >= 200us: RST_n to Command time
1597 * tRSTH >= 1us: RST_n high period
1598 */
1599 reset = mci_readl(host, RST_N);
1600 reset &= ~(SDMMC_RST_HWACTIVE << slot->id);
1601 mci_writel(host, RST_N, reset);
1602 usleep_range(1, 2);
1603 reset |= SDMMC_RST_HWACTIVE << slot->id;
1604 mci_writel(host, RST_N, reset);
1605 usleep_range(200, 300);
1606 }
1607
dw_mci_init_card(struct mmc_host * mmc,struct mmc_card * card)1608 static void dw_mci_init_card(struct mmc_host *mmc, struct mmc_card *card)
1609 {
1610 struct dw_mci_slot *slot = mmc_priv(mmc);
1611 struct dw_mci *host = slot->host;
1612
1613 /*
1614 * Low power mode will stop the card clock when idle. According to the
1615 * description of the CLKENA register we should disable low power mode
1616 * for SDIO cards if we need SDIO interrupts to work.
1617 */
1618 if (mmc->caps & MMC_CAP_SDIO_IRQ) {
1619 const u32 clken_low_pwr = SDMMC_CLKEN_LOW_PWR << slot->id;
1620 u32 clk_en_a_old;
1621 u32 clk_en_a;
1622
1623 clk_en_a_old = mci_readl(host, CLKENA);
1624
1625 if (card->type == MMC_TYPE_SDIO ||
1626 card->type == MMC_TYPE_SD_COMBO) {
1627 set_bit(DW_MMC_CARD_NO_LOW_PWR, &slot->flags);
1628 clk_en_a = clk_en_a_old & ~clken_low_pwr;
1629 } else {
1630 clear_bit(DW_MMC_CARD_NO_LOW_PWR, &slot->flags);
1631 clk_en_a = clk_en_a_old | clken_low_pwr;
1632 }
1633
1634 if (clk_en_a != clk_en_a_old) {
1635 mci_writel(host, CLKENA, clk_en_a);
1636 mci_send_cmd(slot, SDMMC_CMD_UPD_CLK |
1637 SDMMC_CMD_PRV_DAT_WAIT, 0);
1638 }
1639 }
1640 }
1641
__dw_mci_enable_sdio_irq(struct dw_mci_slot * slot,int enb)1642 static void __dw_mci_enable_sdio_irq(struct dw_mci_slot *slot, int enb)
1643 {
1644 struct dw_mci *host = slot->host;
1645 unsigned long irqflags;
1646 u32 int_mask;
1647
1648 spin_lock_irqsave(&host->irq_lock, irqflags);
1649
1650 /* Enable/disable Slot Specific SDIO interrupt */
1651 int_mask = mci_readl(host, INTMASK);
1652 if (enb)
1653 int_mask |= SDMMC_INT_SDIO(slot->sdio_id);
1654 else
1655 int_mask &= ~SDMMC_INT_SDIO(slot->sdio_id);
1656 mci_writel(host, INTMASK, int_mask);
1657
1658 spin_unlock_irqrestore(&host->irq_lock, irqflags);
1659 }
1660
dw_mci_enable_sdio_irq(struct mmc_host * mmc,int enb)1661 static void dw_mci_enable_sdio_irq(struct mmc_host *mmc, int enb)
1662 {
1663 struct dw_mci_slot *slot = mmc_priv(mmc);
1664 struct dw_mci *host = slot->host;
1665
1666 __dw_mci_enable_sdio_irq(slot, enb);
1667
1668 /* Avoid runtime suspending the device when SDIO IRQ is enabled */
1669 if (enb)
1670 pm_runtime_get_noresume(host->dev);
1671 else
1672 pm_runtime_put_noidle(host->dev);
1673 }
1674
dw_mci_ack_sdio_irq(struct mmc_host * mmc)1675 static void dw_mci_ack_sdio_irq(struct mmc_host *mmc)
1676 {
1677 struct dw_mci_slot *slot = mmc_priv(mmc);
1678
1679 __dw_mci_enable_sdio_irq(slot, 1);
1680 }
1681
dw_mci_execute_tuning(struct mmc_host * mmc,u32 opcode)1682 static int dw_mci_execute_tuning(struct mmc_host *mmc, u32 opcode)
1683 {
1684 struct dw_mci_slot *slot = mmc_priv(mmc);
1685 struct dw_mci *host = slot->host;
1686 const struct dw_mci_drv_data *drv_data = host->drv_data;
1687 int err = -EINVAL;
1688
1689 if (drv_data && drv_data->execute_tuning)
1690 err = drv_data->execute_tuning(slot, opcode);
1691 return err;
1692 }
1693
dw_mci_prepare_hs400_tuning(struct mmc_host * mmc,struct mmc_ios * ios)1694 static int dw_mci_prepare_hs400_tuning(struct mmc_host *mmc,
1695 struct mmc_ios *ios)
1696 {
1697 struct dw_mci_slot *slot = mmc_priv(mmc);
1698 struct dw_mci *host = slot->host;
1699 const struct dw_mci_drv_data *drv_data = host->drv_data;
1700
1701 if (drv_data && drv_data->prepare_hs400_tuning)
1702 return drv_data->prepare_hs400_tuning(host, ios);
1703
1704 return 0;
1705 }
1706
dw_mci_reset(struct dw_mci * host)1707 static bool dw_mci_reset(struct dw_mci *host)
1708 {
1709 u32 flags = SDMMC_CTRL_RESET | SDMMC_CTRL_FIFO_RESET;
1710 bool ret = false;
1711 u32 status = 0;
1712
1713 /*
1714 * Resetting generates a block interrupt, hence setting
1715 * the scatter-gather pointer to NULL.
1716 */
1717 if (host->sg) {
1718 sg_miter_stop(&host->sg_miter);
1719 host->sg = NULL;
1720 }
1721
1722 if (host->use_dma)
1723 flags |= SDMMC_CTRL_DMA_RESET;
1724
1725 if (dw_mci_ctrl_reset(host, flags)) {
1726 /*
1727 * In all cases we clear the RAWINTS
1728 * register to clear any interrupts.
1729 */
1730 mci_writel(host, RINTSTS, 0xFFFFFFFF);
1731
1732 if (!host->use_dma) {
1733 ret = true;
1734 goto ciu_out;
1735 }
1736
1737 /* Wait for dma_req to be cleared */
1738 if (readl_poll_timeout_atomic(host->regs + SDMMC_STATUS,
1739 status,
1740 !(status & SDMMC_STATUS_DMA_REQ),
1741 1, 500 * USEC_PER_MSEC)) {
1742 dev_err(host->dev,
1743 "%s: Timeout waiting for dma_req to be cleared\n",
1744 __func__);
1745 goto ciu_out;
1746 }
1747
1748 /* when using DMA next we reset the fifo again */
1749 if (!dw_mci_ctrl_reset(host, SDMMC_CTRL_FIFO_RESET))
1750 goto ciu_out;
1751 } else {
1752 /* if the controller reset bit did clear, then set clock regs */
1753 if (!(mci_readl(host, CTRL) & SDMMC_CTRL_RESET)) {
1754 dev_err(host->dev,
1755 "%s: fifo/dma reset bits didn't clear but ciu was reset, doing clock update\n",
1756 __func__);
1757 goto ciu_out;
1758 }
1759 }
1760
1761 if (host->use_dma == TRANS_MODE_IDMAC)
1762 /* It is also required that we reinit idmac */
1763 dw_mci_idmac_init(host);
1764
1765 ret = true;
1766
1767 ciu_out:
1768 /* After a CTRL reset we need to have CIU set clock registers */
1769 mci_send_cmd(host->slot, SDMMC_CMD_UPD_CLK, 0);
1770
1771 return ret;
1772 }
1773
1774 static const struct mmc_host_ops dw_mci_ops = {
1775 .request = dw_mci_request,
1776 .pre_req = dw_mci_pre_req,
1777 .post_req = dw_mci_post_req,
1778 .set_ios = dw_mci_set_ios,
1779 .get_ro = dw_mci_get_ro,
1780 .get_cd = dw_mci_get_cd,
1781 .hw_reset = dw_mci_hw_reset,
1782 .enable_sdio_irq = dw_mci_enable_sdio_irq,
1783 .ack_sdio_irq = dw_mci_ack_sdio_irq,
1784 .execute_tuning = dw_mci_execute_tuning,
1785 .card_busy = dw_mci_card_busy,
1786 .start_signal_voltage_switch = dw_mci_switch_voltage,
1787 .init_card = dw_mci_init_card,
1788 .prepare_hs400_tuning = dw_mci_prepare_hs400_tuning,
1789 };
1790
dw_mci_request_end(struct dw_mci * host,struct mmc_request * mrq)1791 static void dw_mci_request_end(struct dw_mci *host, struct mmc_request *mrq)
1792 __releases(&host->lock)
1793 __acquires(&host->lock)
1794 {
1795 struct dw_mci_slot *slot;
1796 struct mmc_host *prev_mmc = host->slot->mmc;
1797
1798 WARN_ON(host->cmd || host->data);
1799
1800 host->slot->mrq = NULL;
1801 host->mrq = NULL;
1802 if (!list_empty(&host->queue)) {
1803 slot = list_entry(host->queue.next,
1804 struct dw_mci_slot, queue_node);
1805 list_del(&slot->queue_node);
1806 dev_vdbg(host->dev, "list not empty: %s is next\n",
1807 mmc_hostname(slot->mmc));
1808 host->state = STATE_SENDING_CMD;
1809 dw_mci_start_request(host, slot);
1810 } else {
1811 dev_vdbg(host->dev, "list empty\n");
1812
1813 if (host->state == STATE_SENDING_CMD11)
1814 host->state = STATE_WAITING_CMD11_DONE;
1815 else
1816 host->state = STATE_IDLE;
1817 }
1818
1819 spin_unlock(&host->lock);
1820 mmc_request_done(prev_mmc, mrq);
1821 spin_lock(&host->lock);
1822 }
1823
dw_mci_command_complete(struct dw_mci * host,struct mmc_command * cmd)1824 static int dw_mci_command_complete(struct dw_mci *host, struct mmc_command *cmd)
1825 {
1826 u32 status = host->cmd_status;
1827
1828 host->cmd_status = 0;
1829
1830 /* Read the response from the card (up to 16 bytes) */
1831 if (cmd->flags & MMC_RSP_PRESENT) {
1832 if (cmd->flags & MMC_RSP_136) {
1833 cmd->resp[3] = mci_readl(host, RESP0);
1834 cmd->resp[2] = mci_readl(host, RESP1);
1835 cmd->resp[1] = mci_readl(host, RESP2);
1836 cmd->resp[0] = mci_readl(host, RESP3);
1837 } else {
1838 cmd->resp[0] = mci_readl(host, RESP0);
1839 cmd->resp[1] = 0;
1840 cmd->resp[2] = 0;
1841 cmd->resp[3] = 0;
1842 }
1843 }
1844
1845 if (status & SDMMC_INT_RTO)
1846 cmd->error = -ETIMEDOUT;
1847 else if ((cmd->flags & MMC_RSP_CRC) && (status & SDMMC_INT_RCRC))
1848 cmd->error = -EILSEQ;
1849 else if (status & SDMMC_INT_RESP_ERR)
1850 cmd->error = -EIO;
1851 else
1852 cmd->error = 0;
1853
1854 return cmd->error;
1855 }
1856
dw_mci_data_complete(struct dw_mci * host,struct mmc_data * data)1857 static int dw_mci_data_complete(struct dw_mci *host, struct mmc_data *data)
1858 {
1859 u32 status = host->data_status;
1860
1861 if (status & DW_MCI_DATA_ERROR_FLAGS) {
1862 if (status & SDMMC_INT_DRTO) {
1863 data->error = -ETIMEDOUT;
1864 } else if (status & SDMMC_INT_DCRC) {
1865 data->error = -EILSEQ;
1866 } else if (status & SDMMC_INT_EBE) {
1867 if (host->dir_status ==
1868 DW_MCI_SEND_STATUS) {
1869 /*
1870 * No data CRC status was returned.
1871 * The number of bytes transferred
1872 * will be exaggerated in PIO mode.
1873 */
1874 data->bytes_xfered = 0;
1875 data->error = -ETIMEDOUT;
1876 } else if (host->dir_status ==
1877 DW_MCI_RECV_STATUS) {
1878 data->error = -EILSEQ;
1879 }
1880 } else {
1881 /* SDMMC_INT_SBE is included */
1882 data->error = -EILSEQ;
1883 }
1884
1885 dev_dbg(host->dev, "data error, status 0x%08x\n", status);
1886
1887 /*
1888 * After an error, there may be data lingering
1889 * in the FIFO
1890 */
1891 dw_mci_reset(host);
1892 } else {
1893 data->bytes_xfered = data->blocks * data->blksz;
1894 data->error = 0;
1895 }
1896
1897 return data->error;
1898 }
1899
dw_mci_set_drto(struct dw_mci * host)1900 static void dw_mci_set_drto(struct dw_mci *host)
1901 {
1902 unsigned int drto_clks;
1903 unsigned int drto_div;
1904 unsigned int drto_ms;
1905 unsigned long irqflags;
1906
1907 drto_clks = mci_readl(host, TMOUT) >> 8;
1908 drto_div = (mci_readl(host, CLKDIV) & 0xff) * 2;
1909 if (drto_div == 0)
1910 drto_div = 1;
1911
1912 drto_ms = DIV_ROUND_UP_ULL((u64)MSEC_PER_SEC * drto_clks * drto_div,
1913 host->bus_hz);
1914
1915 /* add a bit spare time */
1916 drto_ms += 10;
1917
1918 spin_lock_irqsave(&host->irq_lock, irqflags);
1919 if (!test_bit(EVENT_DATA_COMPLETE, &host->pending_events))
1920 mod_timer(&host->dto_timer,
1921 jiffies + msecs_to_jiffies(drto_ms));
1922 spin_unlock_irqrestore(&host->irq_lock, irqflags);
1923 }
1924
dw_mci_clear_pending_cmd_complete(struct dw_mci * host)1925 static bool dw_mci_clear_pending_cmd_complete(struct dw_mci *host)
1926 {
1927 if (!test_bit(EVENT_CMD_COMPLETE, &host->pending_events))
1928 return false;
1929
1930 /*
1931 * Really be certain that the timer has stopped. This is a bit of
1932 * paranoia and could only really happen if we had really bad
1933 * interrupt latency and the interrupt routine and timeout were
1934 * running concurrently so that the del_timer() in the interrupt
1935 * handler couldn't run.
1936 */
1937 WARN_ON(del_timer_sync(&host->cto_timer));
1938 clear_bit(EVENT_CMD_COMPLETE, &host->pending_events);
1939
1940 return true;
1941 }
1942
dw_mci_clear_pending_data_complete(struct dw_mci * host)1943 static bool dw_mci_clear_pending_data_complete(struct dw_mci *host)
1944 {
1945 if (!test_bit(EVENT_DATA_COMPLETE, &host->pending_events))
1946 return false;
1947
1948 /* Extra paranoia just like dw_mci_clear_pending_cmd_complete() */
1949 WARN_ON(del_timer_sync(&host->dto_timer));
1950 clear_bit(EVENT_DATA_COMPLETE, &host->pending_events);
1951
1952 return true;
1953 }
1954
dw_mci_tasklet_func(struct tasklet_struct * t)1955 static void dw_mci_tasklet_func(struct tasklet_struct *t)
1956 {
1957 struct dw_mci *host = from_tasklet(host, t, tasklet);
1958 struct mmc_data *data;
1959 struct mmc_command *cmd;
1960 struct mmc_request *mrq;
1961 enum dw_mci_state state;
1962 enum dw_mci_state prev_state;
1963 unsigned int err;
1964
1965 spin_lock(&host->lock);
1966
1967 state = host->state;
1968 data = host->data;
1969 mrq = host->mrq;
1970
1971 do {
1972 prev_state = state;
1973
1974 switch (state) {
1975 case STATE_IDLE:
1976 case STATE_WAITING_CMD11_DONE:
1977 break;
1978
1979 case STATE_SENDING_CMD11:
1980 case STATE_SENDING_CMD:
1981 if (!dw_mci_clear_pending_cmd_complete(host))
1982 break;
1983
1984 cmd = host->cmd;
1985 host->cmd = NULL;
1986 set_bit(EVENT_CMD_COMPLETE, &host->completed_events);
1987 err = dw_mci_command_complete(host, cmd);
1988 if (cmd == mrq->sbc && !err) {
1989 __dw_mci_start_request(host, host->slot,
1990 mrq->cmd);
1991 goto unlock;
1992 }
1993
1994 if (cmd->data && err) {
1995 /*
1996 * During UHS tuning sequence, sending the stop
1997 * command after the response CRC error would
1998 * throw the system into a confused state
1999 * causing all future tuning phases to report
2000 * failure.
2001 *
2002 * In such case controller will move into a data
2003 * transfer state after a response error or
2004 * response CRC error. Let's let that finish
2005 * before trying to send a stop, so we'll go to
2006 * STATE_SENDING_DATA.
2007 *
2008 * Although letting the data transfer take place
2009 * will waste a bit of time (we already know
2010 * the command was bad), it can't cause any
2011 * errors since it's possible it would have
2012 * taken place anyway if this tasklet got
2013 * delayed. Allowing the transfer to take place
2014 * avoids races and keeps things simple.
2015 */
2016 if (err != -ETIMEDOUT) {
2017 state = STATE_SENDING_DATA;
2018 continue;
2019 }
2020
2021 dw_mci_stop_dma(host);
2022 send_stop_abort(host, data);
2023 state = STATE_SENDING_STOP;
2024 break;
2025 }
2026
2027 if (!cmd->data || err) {
2028 dw_mci_request_end(host, mrq);
2029 goto unlock;
2030 }
2031
2032 prev_state = state = STATE_SENDING_DATA;
2033 fallthrough;
2034
2035 case STATE_SENDING_DATA:
2036 /*
2037 * We could get a data error and never a transfer
2038 * complete so we'd better check for it here.
2039 *
2040 * Note that we don't really care if we also got a
2041 * transfer complete; stopping the DMA and sending an
2042 * abort won't hurt.
2043 */
2044 if (test_and_clear_bit(EVENT_DATA_ERROR,
2045 &host->pending_events)) {
2046 dw_mci_stop_dma(host);
2047 if (!(host->data_status & (SDMMC_INT_DRTO |
2048 SDMMC_INT_EBE)))
2049 send_stop_abort(host, data);
2050 state = STATE_DATA_ERROR;
2051 break;
2052 }
2053
2054 if (!test_and_clear_bit(EVENT_XFER_COMPLETE,
2055 &host->pending_events)) {
2056 /*
2057 * If all data-related interrupts don't come
2058 * within the given time in reading data state.
2059 */
2060 if (host->dir_status == DW_MCI_RECV_STATUS)
2061 dw_mci_set_drto(host);
2062 break;
2063 }
2064
2065 set_bit(EVENT_XFER_COMPLETE, &host->completed_events);
2066
2067 /*
2068 * Handle an EVENT_DATA_ERROR that might have shown up
2069 * before the transfer completed. This might not have
2070 * been caught by the check above because the interrupt
2071 * could have gone off between the previous check and
2072 * the check for transfer complete.
2073 *
2074 * Technically this ought not be needed assuming we
2075 * get a DATA_COMPLETE eventually (we'll notice the
2076 * error and end the request), but it shouldn't hurt.
2077 *
2078 * This has the advantage of sending the stop command.
2079 */
2080 if (test_and_clear_bit(EVENT_DATA_ERROR,
2081 &host->pending_events)) {
2082 dw_mci_stop_dma(host);
2083 if (!(host->data_status & (SDMMC_INT_DRTO |
2084 SDMMC_INT_EBE)))
2085 send_stop_abort(host, data);
2086 state = STATE_DATA_ERROR;
2087 break;
2088 }
2089 prev_state = state = STATE_DATA_BUSY;
2090
2091 fallthrough;
2092
2093 case STATE_DATA_BUSY:
2094 if (!dw_mci_clear_pending_data_complete(host)) {
2095 /*
2096 * If data error interrupt comes but data over
2097 * interrupt doesn't come within the given time.
2098 * in reading data state.
2099 */
2100 if (host->dir_status == DW_MCI_RECV_STATUS)
2101 dw_mci_set_drto(host);
2102 break;
2103 }
2104
2105 host->data = NULL;
2106 set_bit(EVENT_DATA_COMPLETE, &host->completed_events);
2107 err = dw_mci_data_complete(host, data);
2108
2109 if (!err) {
2110 if (!data->stop || mrq->sbc) {
2111 if (mrq->sbc && data->stop)
2112 data->stop->error = 0;
2113 dw_mci_request_end(host, mrq);
2114 goto unlock;
2115 }
2116
2117 /* stop command for open-ended transfer*/
2118 if (data->stop)
2119 send_stop_abort(host, data);
2120 } else {
2121 /*
2122 * If we don't have a command complete now we'll
2123 * never get one since we just reset everything;
2124 * better end the request.
2125 *
2126 * If we do have a command complete we'll fall
2127 * through to the SENDING_STOP command and
2128 * everything will be peachy keen.
2129 */
2130 if (!test_bit(EVENT_CMD_COMPLETE,
2131 &host->pending_events)) {
2132 host->cmd = NULL;
2133 dw_mci_request_end(host, mrq);
2134 goto unlock;
2135 }
2136 }
2137
2138 /*
2139 * If err has non-zero,
2140 * stop-abort command has been already issued.
2141 */
2142 prev_state = state = STATE_SENDING_STOP;
2143
2144 fallthrough;
2145
2146 case STATE_SENDING_STOP:
2147 if (!dw_mci_clear_pending_cmd_complete(host))
2148 break;
2149
2150 /* CMD error in data command */
2151 if (mrq->cmd->error && mrq->data)
2152 dw_mci_reset(host);
2153
2154 host->cmd = NULL;
2155 host->data = NULL;
2156
2157 if (!mrq->sbc && mrq->stop)
2158 dw_mci_command_complete(host, mrq->stop);
2159 else
2160 host->cmd_status = 0;
2161
2162 dw_mci_request_end(host, mrq);
2163 goto unlock;
2164
2165 case STATE_DATA_ERROR:
2166 if (!test_and_clear_bit(EVENT_XFER_COMPLETE,
2167 &host->pending_events))
2168 break;
2169
2170 state = STATE_DATA_BUSY;
2171 break;
2172 }
2173 } while (state != prev_state);
2174
2175 host->state = state;
2176 unlock:
2177 spin_unlock(&host->lock);
2178
2179 }
2180
2181 /* push final bytes to part_buf, only use during push */
dw_mci_set_part_bytes(struct dw_mci * host,void * buf,int cnt)2182 static void dw_mci_set_part_bytes(struct dw_mci *host, void *buf, int cnt)
2183 {
2184 memcpy((void *)&host->part_buf, buf, cnt);
2185 host->part_buf_count = cnt;
2186 }
2187
2188 /* append bytes to part_buf, only use during push */
dw_mci_push_part_bytes(struct dw_mci * host,void * buf,int cnt)2189 static int dw_mci_push_part_bytes(struct dw_mci *host, void *buf, int cnt)
2190 {
2191 cnt = min(cnt, (1 << host->data_shift) - host->part_buf_count);
2192 memcpy((void *)&host->part_buf + host->part_buf_count, buf, cnt);
2193 host->part_buf_count += cnt;
2194 return cnt;
2195 }
2196
2197 /* pull first bytes from part_buf, only use during pull */
dw_mci_pull_part_bytes(struct dw_mci * host,void * buf,int cnt)2198 static int dw_mci_pull_part_bytes(struct dw_mci *host, void *buf, int cnt)
2199 {
2200 cnt = min_t(int, cnt, host->part_buf_count);
2201 if (cnt) {
2202 memcpy(buf, (void *)&host->part_buf + host->part_buf_start,
2203 cnt);
2204 host->part_buf_count -= cnt;
2205 host->part_buf_start += cnt;
2206 }
2207 return cnt;
2208 }
2209
2210 /* pull final bytes from the part_buf, assuming it's just been filled */
dw_mci_pull_final_bytes(struct dw_mci * host,void * buf,int cnt)2211 static void dw_mci_pull_final_bytes(struct dw_mci *host, void *buf, int cnt)
2212 {
2213 memcpy(buf, &host->part_buf, cnt);
2214 host->part_buf_start = cnt;
2215 host->part_buf_count = (1 << host->data_shift) - cnt;
2216 }
2217
dw_mci_push_data16(struct dw_mci * host,void * buf,int cnt)2218 static void dw_mci_push_data16(struct dw_mci *host, void *buf, int cnt)
2219 {
2220 struct mmc_data *data = host->data;
2221 int init_cnt = cnt;
2222
2223 /* try and push anything in the part_buf */
2224 if (unlikely(host->part_buf_count)) {
2225 int len = dw_mci_push_part_bytes(host, buf, cnt);
2226
2227 buf += len;
2228 cnt -= len;
2229 if (host->part_buf_count == 2) {
2230 mci_fifo_writew(host->fifo_reg, host->part_buf16);
2231 host->part_buf_count = 0;
2232 }
2233 }
2234 #ifndef CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS
2235 if (unlikely((unsigned long)buf & 0x1)) {
2236 while (cnt >= 2) {
2237 u16 aligned_buf[64];
2238 int len = min(cnt & -2, (int)sizeof(aligned_buf));
2239 int items = len >> 1;
2240 int i;
2241 /* memcpy from input buffer into aligned buffer */
2242 memcpy(aligned_buf, buf, len);
2243 buf += len;
2244 cnt -= len;
2245 /* push data from aligned buffer into fifo */
2246 for (i = 0; i < items; ++i)
2247 mci_fifo_writew(host->fifo_reg, aligned_buf[i]);
2248 }
2249 } else
2250 #endif
2251 {
2252 u16 *pdata = buf;
2253
2254 for (; cnt >= 2; cnt -= 2)
2255 mci_fifo_writew(host->fifo_reg, *pdata++);
2256 buf = pdata;
2257 }
2258 /* put anything remaining in the part_buf */
2259 if (cnt) {
2260 dw_mci_set_part_bytes(host, buf, cnt);
2261 /* Push data if we have reached the expected data length */
2262 if ((data->bytes_xfered + init_cnt) ==
2263 (data->blksz * data->blocks))
2264 mci_fifo_writew(host->fifo_reg, host->part_buf16);
2265 }
2266 }
2267
dw_mci_pull_data16(struct dw_mci * host,void * buf,int cnt)2268 static void dw_mci_pull_data16(struct dw_mci *host, void *buf, int cnt)
2269 {
2270 #ifndef CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS
2271 if (unlikely((unsigned long)buf & 0x1)) {
2272 while (cnt >= 2) {
2273 /* pull data from fifo into aligned buffer */
2274 u16 aligned_buf[64];
2275 int len = min(cnt & -2, (int)sizeof(aligned_buf));
2276 int items = len >> 1;
2277 int i;
2278
2279 for (i = 0; i < items; ++i)
2280 aligned_buf[i] = mci_fifo_readw(host->fifo_reg);
2281 /* memcpy from aligned buffer into output buffer */
2282 memcpy(buf, aligned_buf, len);
2283 buf += len;
2284 cnt -= len;
2285 }
2286 } else
2287 #endif
2288 {
2289 u16 *pdata = buf;
2290
2291 for (; cnt >= 2; cnt -= 2)
2292 *pdata++ = mci_fifo_readw(host->fifo_reg);
2293 buf = pdata;
2294 }
2295 if (cnt) {
2296 host->part_buf16 = mci_fifo_readw(host->fifo_reg);
2297 dw_mci_pull_final_bytes(host, buf, cnt);
2298 }
2299 }
2300
dw_mci_push_data32(struct dw_mci * host,void * buf,int cnt)2301 static void dw_mci_push_data32(struct dw_mci *host, void *buf, int cnt)
2302 {
2303 struct mmc_data *data = host->data;
2304 int init_cnt = cnt;
2305
2306 /* try and push anything in the part_buf */
2307 if (unlikely(host->part_buf_count)) {
2308 int len = dw_mci_push_part_bytes(host, buf, cnt);
2309
2310 buf += len;
2311 cnt -= len;
2312 if (host->part_buf_count == 4) {
2313 mci_fifo_writel(host->fifo_reg, host->part_buf32);
2314 host->part_buf_count = 0;
2315 }
2316 }
2317 #ifndef CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS
2318 if (unlikely((unsigned long)buf & 0x3)) {
2319 while (cnt >= 4) {
2320 u32 aligned_buf[32];
2321 int len = min(cnt & -4, (int)sizeof(aligned_buf));
2322 int items = len >> 2;
2323 int i;
2324 /* memcpy from input buffer into aligned buffer */
2325 memcpy(aligned_buf, buf, len);
2326 buf += len;
2327 cnt -= len;
2328 /* push data from aligned buffer into fifo */
2329 for (i = 0; i < items; ++i)
2330 mci_fifo_writel(host->fifo_reg, aligned_buf[i]);
2331 }
2332 } else
2333 #endif
2334 {
2335 u32 *pdata = buf;
2336
2337 for (; cnt >= 4; cnt -= 4)
2338 mci_fifo_writel(host->fifo_reg, *pdata++);
2339 buf = pdata;
2340 }
2341 /* put anything remaining in the part_buf */
2342 if (cnt) {
2343 dw_mci_set_part_bytes(host, buf, cnt);
2344 /* Push data if we have reached the expected data length */
2345 if ((data->bytes_xfered + init_cnt) ==
2346 (data->blksz * data->blocks))
2347 mci_fifo_writel(host->fifo_reg, host->part_buf32);
2348 }
2349 }
2350
dw_mci_pull_data32(struct dw_mci * host,void * buf,int cnt)2351 static void dw_mci_pull_data32(struct dw_mci *host, void *buf, int cnt)
2352 {
2353 #ifndef CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS
2354 if (unlikely((unsigned long)buf & 0x3)) {
2355 while (cnt >= 4) {
2356 /* pull data from fifo into aligned buffer */
2357 u32 aligned_buf[32];
2358 int len = min(cnt & -4, (int)sizeof(aligned_buf));
2359 int items = len >> 2;
2360 int i;
2361
2362 for (i = 0; i < items; ++i)
2363 aligned_buf[i] = mci_fifo_readl(host->fifo_reg);
2364 /* memcpy from aligned buffer into output buffer */
2365 memcpy(buf, aligned_buf, len);
2366 buf += len;
2367 cnt -= len;
2368 }
2369 } else
2370 #endif
2371 {
2372 u32 *pdata = buf;
2373
2374 for (; cnt >= 4; cnt -= 4)
2375 *pdata++ = mci_fifo_readl(host->fifo_reg);
2376 buf = pdata;
2377 }
2378 if (cnt) {
2379 host->part_buf32 = mci_fifo_readl(host->fifo_reg);
2380 dw_mci_pull_final_bytes(host, buf, cnt);
2381 }
2382 }
2383
dw_mci_push_data64(struct dw_mci * host,void * buf,int cnt)2384 static void dw_mci_push_data64(struct dw_mci *host, void *buf, int cnt)
2385 {
2386 struct mmc_data *data = host->data;
2387 int init_cnt = cnt;
2388
2389 /* try and push anything in the part_buf */
2390 if (unlikely(host->part_buf_count)) {
2391 int len = dw_mci_push_part_bytes(host, buf, cnt);
2392
2393 buf += len;
2394 cnt -= len;
2395
2396 if (host->part_buf_count == 8) {
2397 mci_fifo_writeq(host->fifo_reg, host->part_buf);
2398 host->part_buf_count = 0;
2399 }
2400 }
2401 #ifndef CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS
2402 if (unlikely((unsigned long)buf & 0x7)) {
2403 while (cnt >= 8) {
2404 u64 aligned_buf[16];
2405 int len = min(cnt & -8, (int)sizeof(aligned_buf));
2406 int items = len >> 3;
2407 int i;
2408 /* memcpy from input buffer into aligned buffer */
2409 memcpy(aligned_buf, buf, len);
2410 buf += len;
2411 cnt -= len;
2412 /* push data from aligned buffer into fifo */
2413 for (i = 0; i < items; ++i)
2414 mci_fifo_writeq(host->fifo_reg, aligned_buf[i]);
2415 }
2416 } else
2417 #endif
2418 {
2419 u64 *pdata = buf;
2420
2421 for (; cnt >= 8; cnt -= 8)
2422 mci_fifo_writeq(host->fifo_reg, *pdata++);
2423 buf = pdata;
2424 }
2425 /* put anything remaining in the part_buf */
2426 if (cnt) {
2427 dw_mci_set_part_bytes(host, buf, cnt);
2428 /* Push data if we have reached the expected data length */
2429 if ((data->bytes_xfered + init_cnt) ==
2430 (data->blksz * data->blocks))
2431 mci_fifo_writeq(host->fifo_reg, host->part_buf);
2432 }
2433 }
2434
dw_mci_pull_data64(struct dw_mci * host,void * buf,int cnt)2435 static void dw_mci_pull_data64(struct dw_mci *host, void *buf, int cnt)
2436 {
2437 #ifndef CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS
2438 if (unlikely((unsigned long)buf & 0x7)) {
2439 while (cnt >= 8) {
2440 /* pull data from fifo into aligned buffer */
2441 u64 aligned_buf[16];
2442 int len = min(cnt & -8, (int)sizeof(aligned_buf));
2443 int items = len >> 3;
2444 int i;
2445
2446 for (i = 0; i < items; ++i)
2447 aligned_buf[i] = mci_fifo_readq(host->fifo_reg);
2448
2449 /* memcpy from aligned buffer into output buffer */
2450 memcpy(buf, aligned_buf, len);
2451 buf += len;
2452 cnt -= len;
2453 }
2454 } else
2455 #endif
2456 {
2457 u64 *pdata = buf;
2458
2459 for (; cnt >= 8; cnt -= 8)
2460 *pdata++ = mci_fifo_readq(host->fifo_reg);
2461 buf = pdata;
2462 }
2463 if (cnt) {
2464 host->part_buf = mci_fifo_readq(host->fifo_reg);
2465 dw_mci_pull_final_bytes(host, buf, cnt);
2466 }
2467 }
2468
dw_mci_pull_data(struct dw_mci * host,void * buf,int cnt)2469 static void dw_mci_pull_data(struct dw_mci *host, void *buf, int cnt)
2470 {
2471 int len;
2472
2473 /* get remaining partial bytes */
2474 len = dw_mci_pull_part_bytes(host, buf, cnt);
2475 if (unlikely(len == cnt))
2476 return;
2477 buf += len;
2478 cnt -= len;
2479
2480 /* get the rest of the data */
2481 host->pull_data(host, buf, cnt);
2482 }
2483
dw_mci_read_data_pio(struct dw_mci * host,bool dto)2484 static void dw_mci_read_data_pio(struct dw_mci *host, bool dto)
2485 {
2486 struct sg_mapping_iter *sg_miter = &host->sg_miter;
2487 void *buf;
2488 unsigned int offset;
2489 struct mmc_data *data = host->data;
2490 int shift = host->data_shift;
2491 u32 status;
2492 unsigned int len;
2493 unsigned int remain, fcnt;
2494
2495 do {
2496 if (!sg_miter_next(sg_miter))
2497 goto done;
2498
2499 host->sg = sg_miter->piter.sg;
2500 buf = sg_miter->addr;
2501 remain = sg_miter->length;
2502 offset = 0;
2503
2504 do {
2505 fcnt = (SDMMC_GET_FCNT(mci_readl(host, STATUS))
2506 << shift) + host->part_buf_count;
2507 len = min(remain, fcnt);
2508 if (!len)
2509 break;
2510 dw_mci_pull_data(host, (void *)(buf + offset), len);
2511 data->bytes_xfered += len;
2512 offset += len;
2513 remain -= len;
2514 } while (remain);
2515
2516 sg_miter->consumed = offset;
2517 status = mci_readl(host, MINTSTS);
2518 mci_writel(host, RINTSTS, SDMMC_INT_RXDR);
2519 /* if the RXDR is ready read again */
2520 } while ((status & SDMMC_INT_RXDR) ||
2521 (dto && SDMMC_GET_FCNT(mci_readl(host, STATUS))));
2522
2523 if (!remain) {
2524 if (!sg_miter_next(sg_miter))
2525 goto done;
2526 sg_miter->consumed = 0;
2527 }
2528 sg_miter_stop(sg_miter);
2529 return;
2530
2531 done:
2532 sg_miter_stop(sg_miter);
2533 host->sg = NULL;
2534 smp_wmb(); /* drain writebuffer */
2535 set_bit(EVENT_XFER_COMPLETE, &host->pending_events);
2536 }
2537
dw_mci_write_data_pio(struct dw_mci * host)2538 static void dw_mci_write_data_pio(struct dw_mci *host)
2539 {
2540 struct sg_mapping_iter *sg_miter = &host->sg_miter;
2541 void *buf;
2542 unsigned int offset;
2543 struct mmc_data *data = host->data;
2544 int shift = host->data_shift;
2545 u32 status;
2546 unsigned int len;
2547 unsigned int fifo_depth = host->fifo_depth;
2548 unsigned int remain, fcnt;
2549
2550 do {
2551 if (!sg_miter_next(sg_miter))
2552 goto done;
2553
2554 host->sg = sg_miter->piter.sg;
2555 buf = sg_miter->addr;
2556 remain = sg_miter->length;
2557 offset = 0;
2558
2559 do {
2560 fcnt = ((fifo_depth -
2561 SDMMC_GET_FCNT(mci_readl(host, STATUS)))
2562 << shift) - host->part_buf_count;
2563 len = min(remain, fcnt);
2564 if (!len)
2565 break;
2566 host->push_data(host, (void *)(buf + offset), len);
2567 data->bytes_xfered += len;
2568 offset += len;
2569 remain -= len;
2570 } while (remain);
2571
2572 sg_miter->consumed = offset;
2573 status = mci_readl(host, MINTSTS);
2574 mci_writel(host, RINTSTS, SDMMC_INT_TXDR);
2575 } while (status & SDMMC_INT_TXDR); /* if TXDR write again */
2576
2577 if (!remain) {
2578 if (!sg_miter_next(sg_miter))
2579 goto done;
2580 sg_miter->consumed = 0;
2581 }
2582 sg_miter_stop(sg_miter);
2583 return;
2584
2585 done:
2586 sg_miter_stop(sg_miter);
2587 host->sg = NULL;
2588 smp_wmb(); /* drain writebuffer */
2589 set_bit(EVENT_XFER_COMPLETE, &host->pending_events);
2590 }
2591
dw_mci_cmd_interrupt(struct dw_mci * host,u32 status)2592 static void dw_mci_cmd_interrupt(struct dw_mci *host, u32 status)
2593 {
2594 del_timer(&host->cto_timer);
2595
2596 if (!host->cmd_status)
2597 host->cmd_status = status;
2598
2599 smp_wmb(); /* drain writebuffer */
2600
2601 set_bit(EVENT_CMD_COMPLETE, &host->pending_events);
2602 tasklet_schedule(&host->tasklet);
2603 }
2604
dw_mci_handle_cd(struct dw_mci * host)2605 static void dw_mci_handle_cd(struct dw_mci *host)
2606 {
2607 struct dw_mci_slot *slot = host->slot;
2608
2609 mmc_detect_change(slot->mmc,
2610 msecs_to_jiffies(host->pdata->detect_delay_ms));
2611 }
2612
dw_mci_interrupt(int irq,void * dev_id)2613 static irqreturn_t dw_mci_interrupt(int irq, void *dev_id)
2614 {
2615 struct dw_mci *host = dev_id;
2616 u32 pending;
2617 struct dw_mci_slot *slot = host->slot;
2618
2619 pending = mci_readl(host, MINTSTS); /* read-only mask reg */
2620
2621 if (pending) {
2622 /* Check volt switch first, since it can look like an error */
2623 if ((host->state == STATE_SENDING_CMD11) &&
2624 (pending & SDMMC_INT_VOLT_SWITCH)) {
2625 mci_writel(host, RINTSTS, SDMMC_INT_VOLT_SWITCH);
2626 pending &= ~SDMMC_INT_VOLT_SWITCH;
2627
2628 /*
2629 * Hold the lock; we know cmd11_timer can't be kicked
2630 * off after the lock is released, so safe to delete.
2631 */
2632 spin_lock(&host->irq_lock);
2633 dw_mci_cmd_interrupt(host, pending);
2634 spin_unlock(&host->irq_lock);
2635
2636 del_timer(&host->cmd11_timer);
2637 }
2638
2639 if (pending & DW_MCI_CMD_ERROR_FLAGS) {
2640 spin_lock(&host->irq_lock);
2641
2642 del_timer(&host->cto_timer);
2643 mci_writel(host, RINTSTS, DW_MCI_CMD_ERROR_FLAGS);
2644 host->cmd_status = pending;
2645 smp_wmb(); /* drain writebuffer */
2646 set_bit(EVENT_CMD_COMPLETE, &host->pending_events);
2647
2648 spin_unlock(&host->irq_lock);
2649 }
2650
2651 if (pending & DW_MCI_DATA_ERROR_FLAGS) {
2652 /* if there is an error report DATA_ERROR */
2653 mci_writel(host, RINTSTS, DW_MCI_DATA_ERROR_FLAGS);
2654 host->data_status = pending;
2655 smp_wmb(); /* drain writebuffer */
2656 set_bit(EVENT_DATA_ERROR, &host->pending_events);
2657 tasklet_schedule(&host->tasklet);
2658 }
2659
2660 if (pending & SDMMC_INT_DATA_OVER) {
2661 spin_lock(&host->irq_lock);
2662
2663 del_timer(&host->dto_timer);
2664
2665 mci_writel(host, RINTSTS, SDMMC_INT_DATA_OVER);
2666 if (!host->data_status)
2667 host->data_status = pending;
2668 smp_wmb(); /* drain writebuffer */
2669 if (host->dir_status == DW_MCI_RECV_STATUS) {
2670 if (host->sg != NULL)
2671 dw_mci_read_data_pio(host, true);
2672 }
2673 set_bit(EVENT_DATA_COMPLETE, &host->pending_events);
2674 tasklet_schedule(&host->tasklet);
2675
2676 spin_unlock(&host->irq_lock);
2677 }
2678
2679 if (pending & SDMMC_INT_RXDR) {
2680 mci_writel(host, RINTSTS, SDMMC_INT_RXDR);
2681 if (host->dir_status == DW_MCI_RECV_STATUS && host->sg)
2682 dw_mci_read_data_pio(host, false);
2683 }
2684
2685 if (pending & SDMMC_INT_TXDR) {
2686 mci_writel(host, RINTSTS, SDMMC_INT_TXDR);
2687 if (host->dir_status == DW_MCI_SEND_STATUS && host->sg)
2688 dw_mci_write_data_pio(host);
2689 }
2690
2691 if (pending & SDMMC_INT_CMD_DONE) {
2692 spin_lock(&host->irq_lock);
2693
2694 mci_writel(host, RINTSTS, SDMMC_INT_CMD_DONE);
2695 dw_mci_cmd_interrupt(host, pending);
2696
2697 spin_unlock(&host->irq_lock);
2698 }
2699
2700 if (pending & SDMMC_INT_CD) {
2701 mci_writel(host, RINTSTS, SDMMC_INT_CD);
2702 dw_mci_handle_cd(host);
2703 }
2704
2705 if (pending & SDMMC_INT_SDIO(slot->sdio_id)) {
2706 mci_writel(host, RINTSTS,
2707 SDMMC_INT_SDIO(slot->sdio_id));
2708 __dw_mci_enable_sdio_irq(slot, 0);
2709 sdio_signal_irq(slot->mmc);
2710 }
2711
2712 }
2713
2714 if (host->use_dma != TRANS_MODE_IDMAC)
2715 return IRQ_HANDLED;
2716
2717 /* Handle IDMA interrupts */
2718 if (host->dma_64bit_address == 1) {
2719 pending = mci_readl(host, IDSTS64);
2720 if (pending & (SDMMC_IDMAC_INT_TI | SDMMC_IDMAC_INT_RI)) {
2721 mci_writel(host, IDSTS64, SDMMC_IDMAC_INT_TI |
2722 SDMMC_IDMAC_INT_RI);
2723 mci_writel(host, IDSTS64, SDMMC_IDMAC_INT_NI);
2724 if (!test_bit(EVENT_DATA_ERROR, &host->pending_events))
2725 host->dma_ops->complete((void *)host);
2726 }
2727 } else {
2728 pending = mci_readl(host, IDSTS);
2729 if (pending & (SDMMC_IDMAC_INT_TI | SDMMC_IDMAC_INT_RI)) {
2730 mci_writel(host, IDSTS, SDMMC_IDMAC_INT_TI |
2731 SDMMC_IDMAC_INT_RI);
2732 mci_writel(host, IDSTS, SDMMC_IDMAC_INT_NI);
2733 if (!test_bit(EVENT_DATA_ERROR, &host->pending_events))
2734 host->dma_ops->complete((void *)host);
2735 }
2736 }
2737
2738 return IRQ_HANDLED;
2739 }
2740
dw_mci_init_slot_caps(struct dw_mci_slot * slot)2741 static int dw_mci_init_slot_caps(struct dw_mci_slot *slot)
2742 {
2743 struct dw_mci *host = slot->host;
2744 const struct dw_mci_drv_data *drv_data = host->drv_data;
2745 struct mmc_host *mmc = slot->mmc;
2746 int ctrl_id;
2747
2748 if (host->pdata->caps)
2749 mmc->caps = host->pdata->caps;
2750
2751 if (host->pdata->pm_caps)
2752 mmc->pm_caps = host->pdata->pm_caps;
2753
2754 if (host->dev->of_node) {
2755 ctrl_id = of_alias_get_id(host->dev->of_node, "mshc");
2756 if (ctrl_id < 0)
2757 ctrl_id = 0;
2758 } else {
2759 ctrl_id = to_platform_device(host->dev)->id;
2760 }
2761
2762 if (drv_data && drv_data->caps) {
2763 if (ctrl_id >= drv_data->num_caps) {
2764 dev_err(host->dev, "invalid controller id %d\n",
2765 ctrl_id);
2766 return -EINVAL;
2767 }
2768 mmc->caps |= drv_data->caps[ctrl_id];
2769 }
2770
2771 if (host->pdata->caps2)
2772 mmc->caps2 = host->pdata->caps2;
2773
2774 mmc->f_min = DW_MCI_FREQ_MIN;
2775 if (!mmc->f_max)
2776 mmc->f_max = DW_MCI_FREQ_MAX;
2777
2778 /* Process SDIO IRQs through the sdio_irq_work. */
2779 if (mmc->caps & MMC_CAP_SDIO_IRQ)
2780 mmc->caps2 |= MMC_CAP2_SDIO_IRQ_NOTHREAD;
2781
2782 return 0;
2783 }
2784
dw_mci_init_slot(struct dw_mci * host)2785 static int dw_mci_init_slot(struct dw_mci *host)
2786 {
2787 struct mmc_host *mmc;
2788 struct dw_mci_slot *slot;
2789 int ret;
2790
2791 mmc = mmc_alloc_host(sizeof(struct dw_mci_slot), host->dev);
2792 if (!mmc)
2793 return -ENOMEM;
2794
2795 slot = mmc_priv(mmc);
2796 slot->id = 0;
2797 slot->sdio_id = host->sdio_id0 + slot->id;
2798 slot->mmc = mmc;
2799 slot->host = host;
2800 host->slot = slot;
2801
2802 mmc->ops = &dw_mci_ops;
2803
2804 /*if there are external regulators, get them*/
2805 ret = mmc_regulator_get_supply(mmc);
2806 if (ret)
2807 goto err_host_allocated;
2808
2809 if (!mmc->ocr_avail)
2810 mmc->ocr_avail = MMC_VDD_32_33 | MMC_VDD_33_34;
2811
2812 ret = mmc_of_parse(mmc);
2813 if (ret)
2814 goto err_host_allocated;
2815
2816 ret = dw_mci_init_slot_caps(slot);
2817 if (ret)
2818 goto err_host_allocated;
2819
2820 /* Useful defaults if platform data is unset. */
2821 if (host->use_dma == TRANS_MODE_IDMAC) {
2822 mmc->max_segs = host->ring_size;
2823 mmc->max_blk_size = 65535;
2824 mmc->max_seg_size = 0x1000;
2825 mmc->max_req_size = mmc->max_seg_size * host->ring_size;
2826 mmc->max_blk_count = mmc->max_req_size / 512;
2827 } else if (host->use_dma == TRANS_MODE_EDMAC) {
2828 mmc->max_segs = 64;
2829 mmc->max_blk_size = 65535;
2830 mmc->max_blk_count = 65535;
2831 mmc->max_req_size =
2832 mmc->max_blk_size * mmc->max_blk_count;
2833 mmc->max_seg_size = mmc->max_req_size;
2834 } else {
2835 /* TRANS_MODE_PIO */
2836 mmc->max_segs = 64;
2837 mmc->max_blk_size = 65535; /* BLKSIZ is 16 bits */
2838 mmc->max_blk_count = 512;
2839 mmc->max_req_size = mmc->max_blk_size *
2840 mmc->max_blk_count;
2841 mmc->max_seg_size = mmc->max_req_size;
2842 }
2843
2844 dw_mci_get_cd(mmc);
2845
2846 ret = mmc_add_host(mmc);
2847 if (ret)
2848 goto err_host_allocated;
2849
2850 #if defined(CONFIG_DEBUG_FS)
2851 dw_mci_init_debugfs(slot);
2852 #endif
2853
2854 return 0;
2855
2856 err_host_allocated:
2857 mmc_free_host(mmc);
2858 return ret;
2859 }
2860
dw_mci_cleanup_slot(struct dw_mci_slot * slot)2861 static void dw_mci_cleanup_slot(struct dw_mci_slot *slot)
2862 {
2863 /* Debugfs stuff is cleaned up by mmc core */
2864 mmc_remove_host(slot->mmc);
2865 slot->host->slot = NULL;
2866 mmc_free_host(slot->mmc);
2867 }
2868
dw_mci_init_dma(struct dw_mci * host)2869 static void dw_mci_init_dma(struct dw_mci *host)
2870 {
2871 int addr_config;
2872 struct device *dev = host->dev;
2873
2874 /*
2875 * Check tansfer mode from HCON[17:16]
2876 * Clear the ambiguous description of dw_mmc databook:
2877 * 2b'00: No DMA Interface -> Actually means using Internal DMA block
2878 * 2b'01: DesignWare DMA Interface -> Synopsys DW-DMA block
2879 * 2b'10: Generic DMA Interface -> non-Synopsys generic DMA block
2880 * 2b'11: Non DW DMA Interface -> pio only
2881 * Compared to DesignWare DMA Interface, Generic DMA Interface has a
2882 * simpler request/acknowledge handshake mechanism and both of them
2883 * are regarded as external dma master for dw_mmc.
2884 */
2885 host->use_dma = SDMMC_GET_TRANS_MODE(mci_readl(host, HCON));
2886 if (host->use_dma == DMA_INTERFACE_IDMA) {
2887 host->use_dma = TRANS_MODE_IDMAC;
2888 } else if (host->use_dma == DMA_INTERFACE_DWDMA ||
2889 host->use_dma == DMA_INTERFACE_GDMA) {
2890 host->use_dma = TRANS_MODE_EDMAC;
2891 } else {
2892 goto no_dma;
2893 }
2894
2895 /* Determine which DMA interface to use */
2896 if (host->use_dma == TRANS_MODE_IDMAC) {
2897 /*
2898 * Check ADDR_CONFIG bit in HCON to find
2899 * IDMAC address bus width
2900 */
2901 addr_config = SDMMC_GET_ADDR_CONFIG(mci_readl(host, HCON));
2902
2903 if (addr_config == 1) {
2904 /* host supports IDMAC in 64-bit address mode */
2905 host->dma_64bit_address = 1;
2906 dev_info(host->dev,
2907 "IDMAC supports 64-bit address mode.\n");
2908 if (!dma_set_mask(host->dev, DMA_BIT_MASK(64)))
2909 dma_set_coherent_mask(host->dev,
2910 DMA_BIT_MASK(64));
2911 } else {
2912 /* host supports IDMAC in 32-bit address mode */
2913 host->dma_64bit_address = 0;
2914 dev_info(host->dev,
2915 "IDMAC supports 32-bit address mode.\n");
2916 }
2917
2918 /* Alloc memory for sg translation */
2919 host->sg_cpu = dmam_alloc_coherent(host->dev,
2920 DESC_RING_BUF_SZ,
2921 &host->sg_dma, GFP_KERNEL);
2922 if (!host->sg_cpu) {
2923 dev_err(host->dev,
2924 "%s: could not alloc DMA memory\n",
2925 __func__);
2926 goto no_dma;
2927 }
2928
2929 host->dma_ops = &dw_mci_idmac_ops;
2930 dev_info(host->dev, "Using internal DMA controller.\n");
2931 } else {
2932 /* TRANS_MODE_EDMAC: check dma bindings again */
2933 if ((device_property_read_string_array(dev, "dma-names",
2934 NULL, 0) < 0) ||
2935 !device_property_present(dev, "dmas")) {
2936 goto no_dma;
2937 }
2938 host->dma_ops = &dw_mci_edmac_ops;
2939 dev_info(host->dev, "Using external DMA controller.\n");
2940 }
2941
2942 if (host->dma_ops->init && host->dma_ops->start &&
2943 host->dma_ops->stop && host->dma_ops->cleanup) {
2944 if (host->dma_ops->init(host)) {
2945 dev_err(host->dev, "%s: Unable to initialize DMA Controller.\n",
2946 __func__);
2947 goto no_dma;
2948 }
2949 } else {
2950 dev_err(host->dev, "DMA initialization not found.\n");
2951 goto no_dma;
2952 }
2953
2954 return;
2955
2956 no_dma:
2957 dev_info(host->dev, "Using PIO mode.\n");
2958 host->use_dma = TRANS_MODE_PIO;
2959 }
2960
dw_mci_cmd11_timer(struct timer_list * t)2961 static void dw_mci_cmd11_timer(struct timer_list *t)
2962 {
2963 struct dw_mci *host = from_timer(host, t, cmd11_timer);
2964
2965 if (host->state != STATE_SENDING_CMD11) {
2966 dev_warn(host->dev, "Unexpected CMD11 timeout\n");
2967 return;
2968 }
2969
2970 host->cmd_status = SDMMC_INT_RTO;
2971 set_bit(EVENT_CMD_COMPLETE, &host->pending_events);
2972 tasklet_schedule(&host->tasklet);
2973 }
2974
dw_mci_cto_timer(struct timer_list * t)2975 static void dw_mci_cto_timer(struct timer_list *t)
2976 {
2977 struct dw_mci *host = from_timer(host, t, cto_timer);
2978 unsigned long irqflags;
2979 u32 pending;
2980
2981 spin_lock_irqsave(&host->irq_lock, irqflags);
2982
2983 /*
2984 * If somehow we have very bad interrupt latency it's remotely possible
2985 * that the timer could fire while the interrupt is still pending or
2986 * while the interrupt is midway through running. Let's be paranoid
2987 * and detect those two cases. Note that this is paranoia is somewhat
2988 * justified because in this function we don't actually cancel the
2989 * pending command in the controller--we just assume it will never come.
2990 */
2991 pending = mci_readl(host, MINTSTS); /* read-only mask reg */
2992 if (pending & (DW_MCI_CMD_ERROR_FLAGS | SDMMC_INT_CMD_DONE)) {
2993 /* The interrupt should fire; no need to act but we can warn */
2994 dev_warn(host->dev, "Unexpected interrupt latency\n");
2995 goto exit;
2996 }
2997 if (test_bit(EVENT_CMD_COMPLETE, &host->pending_events)) {
2998 /* Presumably interrupt handler couldn't delete the timer */
2999 dev_warn(host->dev, "CTO timeout when already completed\n");
3000 goto exit;
3001 }
3002
3003 /*
3004 * Continued paranoia to make sure we're in the state we expect.
3005 * This paranoia isn't really justified but it seems good to be safe.
3006 */
3007 switch (host->state) {
3008 case STATE_SENDING_CMD11:
3009 case STATE_SENDING_CMD:
3010 case STATE_SENDING_STOP:
3011 /*
3012 * If CMD_DONE interrupt does NOT come in sending command
3013 * state, we should notify the driver to terminate current
3014 * transfer and report a command timeout to the core.
3015 */
3016 host->cmd_status = SDMMC_INT_RTO;
3017 set_bit(EVENT_CMD_COMPLETE, &host->pending_events);
3018 tasklet_schedule(&host->tasklet);
3019 break;
3020 default:
3021 dev_warn(host->dev, "Unexpected command timeout, state %d\n",
3022 host->state);
3023 break;
3024 }
3025
3026 exit:
3027 spin_unlock_irqrestore(&host->irq_lock, irqflags);
3028 }
3029
dw_mci_dto_timer(struct timer_list * t)3030 static void dw_mci_dto_timer(struct timer_list *t)
3031 {
3032 struct dw_mci *host = from_timer(host, t, dto_timer);
3033 unsigned long irqflags;
3034 u32 pending;
3035
3036 spin_lock_irqsave(&host->irq_lock, irqflags);
3037
3038 /*
3039 * The DTO timer is much longer than the CTO timer, so it's even less
3040 * likely that we'll these cases, but it pays to be paranoid.
3041 */
3042 pending = mci_readl(host, MINTSTS); /* read-only mask reg */
3043 if (pending & SDMMC_INT_DATA_OVER) {
3044 /* The interrupt should fire; no need to act but we can warn */
3045 dev_warn(host->dev, "Unexpected data interrupt latency\n");
3046 goto exit;
3047 }
3048 if (test_bit(EVENT_DATA_COMPLETE, &host->pending_events)) {
3049 /* Presumably interrupt handler couldn't delete the timer */
3050 dev_warn(host->dev, "DTO timeout when already completed\n");
3051 goto exit;
3052 }
3053
3054 /*
3055 * Continued paranoia to make sure we're in the state we expect.
3056 * This paranoia isn't really justified but it seems good to be safe.
3057 */
3058 switch (host->state) {
3059 case STATE_SENDING_DATA:
3060 case STATE_DATA_BUSY:
3061 /*
3062 * If DTO interrupt does NOT come in sending data state,
3063 * we should notify the driver to terminate current transfer
3064 * and report a data timeout to the core.
3065 */
3066 host->data_status = SDMMC_INT_DRTO;
3067 set_bit(EVENT_DATA_ERROR, &host->pending_events);
3068 set_bit(EVENT_DATA_COMPLETE, &host->pending_events);
3069 tasklet_schedule(&host->tasklet);
3070 break;
3071 default:
3072 dev_warn(host->dev, "Unexpected data timeout, state %d\n",
3073 host->state);
3074 break;
3075 }
3076
3077 exit:
3078 spin_unlock_irqrestore(&host->irq_lock, irqflags);
3079 }
3080
3081 #ifdef CONFIG_OF
dw_mci_parse_dt(struct dw_mci * host)3082 static struct dw_mci_board *dw_mci_parse_dt(struct dw_mci *host)
3083 {
3084 struct dw_mci_board *pdata;
3085 struct device *dev = host->dev;
3086 const struct dw_mci_drv_data *drv_data = host->drv_data;
3087 int ret;
3088 u32 clock_frequency;
3089
3090 pdata = devm_kzalloc(dev, sizeof(*pdata), GFP_KERNEL);
3091 if (!pdata)
3092 return ERR_PTR(-ENOMEM);
3093
3094 /* find reset controller when exist */
3095 pdata->rstc = devm_reset_control_get_optional_exclusive(dev, "reset");
3096 if (IS_ERR(pdata->rstc))
3097 return ERR_CAST(pdata->rstc);
3098
3099 if (device_property_read_u32(dev, "fifo-depth", &pdata->fifo_depth))
3100 dev_info(dev,
3101 "fifo-depth property not found, using value of FIFOTH register as default\n");
3102
3103 device_property_read_u32(dev, "card-detect-delay",
3104 &pdata->detect_delay_ms);
3105
3106 device_property_read_u32(dev, "data-addr", &host->data_addr_override);
3107
3108 if (device_property_present(dev, "fifo-watermark-aligned"))
3109 host->wm_aligned = true;
3110
3111 if (!device_property_read_u32(dev, "clock-frequency", &clock_frequency))
3112 pdata->bus_hz = clock_frequency;
3113
3114 if (drv_data && drv_data->parse_dt) {
3115 ret = drv_data->parse_dt(host);
3116 if (ret)
3117 return ERR_PTR(ret);
3118 }
3119
3120 return pdata;
3121 }
3122
3123 #else /* CONFIG_OF */
dw_mci_parse_dt(struct dw_mci * host)3124 static struct dw_mci_board *dw_mci_parse_dt(struct dw_mci *host)
3125 {
3126 return ERR_PTR(-EINVAL);
3127 }
3128 #endif /* CONFIG_OF */
3129
dw_mci_enable_cd(struct dw_mci * host)3130 static void dw_mci_enable_cd(struct dw_mci *host)
3131 {
3132 unsigned long irqflags;
3133 u32 temp;
3134
3135 /*
3136 * No need for CD if all slots have a non-error GPIO
3137 * as well as broken card detection is found.
3138 */
3139 if (host->slot->mmc->caps & MMC_CAP_NEEDS_POLL)
3140 return;
3141
3142 if (mmc_gpio_get_cd(host->slot->mmc) < 0) {
3143 spin_lock_irqsave(&host->irq_lock, irqflags);
3144 temp = mci_readl(host, INTMASK);
3145 temp |= SDMMC_INT_CD;
3146 mci_writel(host, INTMASK, temp);
3147 spin_unlock_irqrestore(&host->irq_lock, irqflags);
3148 }
3149 }
3150
dw_mci_probe(struct dw_mci * host)3151 int dw_mci_probe(struct dw_mci *host)
3152 {
3153 const struct dw_mci_drv_data *drv_data = host->drv_data;
3154 int width, i, ret = 0;
3155 u32 fifo_size;
3156
3157 if (!host->pdata) {
3158 host->pdata = dw_mci_parse_dt(host);
3159 if (IS_ERR(host->pdata))
3160 return dev_err_probe(host->dev, PTR_ERR(host->pdata),
3161 "platform data not available\n");
3162 }
3163
3164 host->biu_clk = devm_clk_get(host->dev, "biu");
3165 if (IS_ERR(host->biu_clk)) {
3166 dev_dbg(host->dev, "biu clock not available\n");
3167 } else {
3168 ret = clk_prepare_enable(host->biu_clk);
3169 if (ret) {
3170 dev_err(host->dev, "failed to enable biu clock\n");
3171 return ret;
3172 }
3173 }
3174
3175 host->ciu_clk = devm_clk_get(host->dev, "ciu");
3176 if (IS_ERR(host->ciu_clk)) {
3177 dev_dbg(host->dev, "ciu clock not available\n");
3178 host->bus_hz = host->pdata->bus_hz;
3179 } else {
3180 ret = clk_prepare_enable(host->ciu_clk);
3181 if (ret) {
3182 dev_err(host->dev, "failed to enable ciu clock\n");
3183 goto err_clk_biu;
3184 }
3185
3186 if (host->pdata->bus_hz) {
3187 ret = clk_set_rate(host->ciu_clk, host->pdata->bus_hz);
3188 if (ret)
3189 dev_warn(host->dev,
3190 "Unable to set bus rate to %uHz\n",
3191 host->pdata->bus_hz);
3192 }
3193 host->bus_hz = clk_get_rate(host->ciu_clk);
3194 }
3195
3196 if (!host->bus_hz) {
3197 dev_err(host->dev,
3198 "Platform data must supply bus speed\n");
3199 ret = -ENODEV;
3200 goto err_clk_ciu;
3201 }
3202
3203 if (host->pdata->rstc) {
3204 reset_control_assert(host->pdata->rstc);
3205 usleep_range(10, 50);
3206 reset_control_deassert(host->pdata->rstc);
3207 }
3208
3209 if (drv_data && drv_data->init) {
3210 ret = drv_data->init(host);
3211 if (ret) {
3212 dev_err(host->dev,
3213 "implementation specific init failed\n");
3214 goto err_clk_ciu;
3215 }
3216 }
3217
3218 timer_setup(&host->cmd11_timer, dw_mci_cmd11_timer, 0);
3219 timer_setup(&host->cto_timer, dw_mci_cto_timer, 0);
3220 timer_setup(&host->dto_timer, dw_mci_dto_timer, 0);
3221
3222 spin_lock_init(&host->lock);
3223 spin_lock_init(&host->irq_lock);
3224 INIT_LIST_HEAD(&host->queue);
3225
3226 /*
3227 * Get the host data width - this assumes that HCON has been set with
3228 * the correct values.
3229 */
3230 i = SDMMC_GET_HDATA_WIDTH(mci_readl(host, HCON));
3231 if (!i) {
3232 host->push_data = dw_mci_push_data16;
3233 host->pull_data = dw_mci_pull_data16;
3234 width = 16;
3235 host->data_shift = 1;
3236 } else if (i == 2) {
3237 host->push_data = dw_mci_push_data64;
3238 host->pull_data = dw_mci_pull_data64;
3239 width = 64;
3240 host->data_shift = 3;
3241 } else {
3242 /* Check for a reserved value, and warn if it is */
3243 WARN((i != 1),
3244 "HCON reports a reserved host data width!\n"
3245 "Defaulting to 32-bit access.\n");
3246 host->push_data = dw_mci_push_data32;
3247 host->pull_data = dw_mci_pull_data32;
3248 width = 32;
3249 host->data_shift = 2;
3250 }
3251
3252 /* Reset all blocks */
3253 if (!dw_mci_ctrl_reset(host, SDMMC_CTRL_ALL_RESET_FLAGS)) {
3254 ret = -ENODEV;
3255 goto err_clk_ciu;
3256 }
3257
3258 host->dma_ops = host->pdata->dma_ops;
3259 dw_mci_init_dma(host);
3260
3261 /* Clear the interrupts for the host controller */
3262 mci_writel(host, RINTSTS, 0xFFFFFFFF);
3263 mci_writel(host, INTMASK, 0); /* disable all mmc interrupt first */
3264
3265 /* Put in max timeout */
3266 mci_writel(host, TMOUT, 0xFFFFFFFF);
3267
3268 /*
3269 * FIFO threshold settings RxMark = fifo_size / 2 - 1,
3270 * Tx Mark = fifo_size / 2 DMA Size = 8
3271 */
3272 if (!host->pdata->fifo_depth) {
3273 /*
3274 * Power-on value of RX_WMark is FIFO_DEPTH-1, but this may
3275 * have been overwritten by the bootloader, just like we're
3276 * about to do, so if you know the value for your hardware, you
3277 * should put it in the platform data.
3278 */
3279 fifo_size = mci_readl(host, FIFOTH);
3280 fifo_size = 1 + ((fifo_size >> 16) & 0xfff);
3281 } else {
3282 fifo_size = host->pdata->fifo_depth;
3283 }
3284 host->fifo_depth = fifo_size;
3285 host->fifoth_val =
3286 SDMMC_SET_FIFOTH(0x2, fifo_size / 2 - 1, fifo_size / 2);
3287 mci_writel(host, FIFOTH, host->fifoth_val);
3288
3289 /* disable clock to CIU */
3290 mci_writel(host, CLKENA, 0);
3291 mci_writel(host, CLKSRC, 0);
3292
3293 /*
3294 * In 2.40a spec, Data offset is changed.
3295 * Need to check the version-id and set data-offset for DATA register.
3296 */
3297 host->verid = SDMMC_GET_VERID(mci_readl(host, VERID));
3298 dev_info(host->dev, "Version ID is %04x\n", host->verid);
3299
3300 if (host->data_addr_override)
3301 host->fifo_reg = host->regs + host->data_addr_override;
3302 else if (host->verid < DW_MMC_240A)
3303 host->fifo_reg = host->regs + DATA_OFFSET;
3304 else
3305 host->fifo_reg = host->regs + DATA_240A_OFFSET;
3306
3307 tasklet_setup(&host->tasklet, dw_mci_tasklet_func);
3308 ret = devm_request_irq(host->dev, host->irq, dw_mci_interrupt,
3309 host->irq_flags, "dw-mci", host);
3310 if (ret)
3311 goto err_dmaunmap;
3312
3313 /*
3314 * Enable interrupts for command done, data over, data empty,
3315 * receive ready and error such as transmit, receive timeout, crc error
3316 */
3317 mci_writel(host, INTMASK, SDMMC_INT_CMD_DONE | SDMMC_INT_DATA_OVER |
3318 SDMMC_INT_TXDR | SDMMC_INT_RXDR |
3319 DW_MCI_ERROR_FLAGS);
3320 /* Enable mci interrupt */
3321 mci_writel(host, CTRL, SDMMC_CTRL_INT_ENABLE);
3322
3323 dev_info(host->dev,
3324 "DW MMC controller at irq %d,%d bit host data width,%u deep fifo\n",
3325 host->irq, width, fifo_size);
3326
3327 /* We need at least one slot to succeed */
3328 ret = dw_mci_init_slot(host);
3329 if (ret) {
3330 dev_dbg(host->dev, "slot %d init failed\n", i);
3331 goto err_dmaunmap;
3332 }
3333
3334 /* Now that slots are all setup, we can enable card detect */
3335 dw_mci_enable_cd(host);
3336
3337 return 0;
3338
3339 err_dmaunmap:
3340 if (host->use_dma && host->dma_ops->exit)
3341 host->dma_ops->exit(host);
3342
3343 reset_control_assert(host->pdata->rstc);
3344
3345 err_clk_ciu:
3346 clk_disable_unprepare(host->ciu_clk);
3347
3348 err_clk_biu:
3349 clk_disable_unprepare(host->biu_clk);
3350
3351 return ret;
3352 }
3353 EXPORT_SYMBOL(dw_mci_probe);
3354
dw_mci_remove(struct dw_mci * host)3355 void dw_mci_remove(struct dw_mci *host)
3356 {
3357 dev_dbg(host->dev, "remove slot\n");
3358 if (host->slot)
3359 dw_mci_cleanup_slot(host->slot);
3360
3361 mci_writel(host, RINTSTS, 0xFFFFFFFF);
3362 mci_writel(host, INTMASK, 0); /* disable all mmc interrupt first */
3363
3364 /* disable clock to CIU */
3365 mci_writel(host, CLKENA, 0);
3366 mci_writel(host, CLKSRC, 0);
3367
3368 if (host->use_dma && host->dma_ops->exit)
3369 host->dma_ops->exit(host);
3370
3371 reset_control_assert(host->pdata->rstc);
3372
3373 clk_disable_unprepare(host->ciu_clk);
3374 clk_disable_unprepare(host->biu_clk);
3375 }
3376 EXPORT_SYMBOL(dw_mci_remove);
3377
3378
3379
3380 #ifdef CONFIG_PM
dw_mci_runtime_suspend(struct device * dev)3381 int dw_mci_runtime_suspend(struct device *dev)
3382 {
3383 struct dw_mci *host = dev_get_drvdata(dev);
3384
3385 if (host->use_dma && host->dma_ops->exit)
3386 host->dma_ops->exit(host);
3387
3388 clk_disable_unprepare(host->ciu_clk);
3389
3390 if (host->slot &&
3391 (mmc_can_gpio_cd(host->slot->mmc) ||
3392 !mmc_card_is_removable(host->slot->mmc)))
3393 clk_disable_unprepare(host->biu_clk);
3394
3395 return 0;
3396 }
3397 EXPORT_SYMBOL(dw_mci_runtime_suspend);
3398
dw_mci_runtime_resume(struct device * dev)3399 int dw_mci_runtime_resume(struct device *dev)
3400 {
3401 int ret = 0;
3402 struct dw_mci *host = dev_get_drvdata(dev);
3403
3404 if (host->slot &&
3405 (mmc_can_gpio_cd(host->slot->mmc) ||
3406 !mmc_card_is_removable(host->slot->mmc))) {
3407 ret = clk_prepare_enable(host->biu_clk);
3408 if (ret)
3409 return ret;
3410 }
3411
3412 ret = clk_prepare_enable(host->ciu_clk);
3413 if (ret)
3414 goto err;
3415
3416 if (!dw_mci_ctrl_reset(host, SDMMC_CTRL_ALL_RESET_FLAGS)) {
3417 clk_disable_unprepare(host->ciu_clk);
3418 ret = -ENODEV;
3419 goto err;
3420 }
3421
3422 if (host->use_dma && host->dma_ops->init)
3423 host->dma_ops->init(host);
3424
3425 /*
3426 * Restore the initial value at FIFOTH register
3427 * And Invalidate the prev_blksz with zero
3428 */
3429 mci_writel(host, FIFOTH, host->fifoth_val);
3430 host->prev_blksz = 0;
3431
3432 /* Put in max timeout */
3433 mci_writel(host, TMOUT, 0xFFFFFFFF);
3434
3435 mci_writel(host, RINTSTS, 0xFFFFFFFF);
3436 mci_writel(host, INTMASK, SDMMC_INT_CMD_DONE | SDMMC_INT_DATA_OVER |
3437 SDMMC_INT_TXDR | SDMMC_INT_RXDR |
3438 DW_MCI_ERROR_FLAGS);
3439 mci_writel(host, CTRL, SDMMC_CTRL_INT_ENABLE);
3440
3441
3442 if (host->slot->mmc->pm_flags & MMC_PM_KEEP_POWER)
3443 dw_mci_set_ios(host->slot->mmc, &host->slot->mmc->ios);
3444
3445 /* Force setup bus to guarantee available clock output */
3446 dw_mci_setup_bus(host->slot, true);
3447
3448 /* Re-enable SDIO interrupts. */
3449 if (sdio_irq_claimed(host->slot->mmc))
3450 __dw_mci_enable_sdio_irq(host->slot, 1);
3451
3452 /* Now that slots are all setup, we can enable card detect */
3453 dw_mci_enable_cd(host);
3454
3455 return 0;
3456
3457 err:
3458 if (host->slot &&
3459 (mmc_can_gpio_cd(host->slot->mmc) ||
3460 !mmc_card_is_removable(host->slot->mmc)))
3461 clk_disable_unprepare(host->biu_clk);
3462
3463 return ret;
3464 }
3465 EXPORT_SYMBOL(dw_mci_runtime_resume);
3466 #endif /* CONFIG_PM */
3467
dw_mci_init(void)3468 static int __init dw_mci_init(void)
3469 {
3470 pr_info("Synopsys Designware Multimedia Card Interface Driver\n");
3471 return 0;
3472 }
3473
dw_mci_exit(void)3474 static void __exit dw_mci_exit(void)
3475 {
3476 }
3477
3478 module_init(dw_mci_init);
3479 module_exit(dw_mci_exit);
3480
3481 MODULE_DESCRIPTION("DW Multimedia Card Interface driver");
3482 MODULE_AUTHOR("NXP Semiconductor VietNam");
3483 MODULE_AUTHOR("Imagination Technologies Ltd");
3484 MODULE_LICENSE("GPL v2");
3485