1-- *****************************************************************
2-- CISCO-ITP-RT-MIB: Itp Signalling Point Routing Table
3--
4-- August 2001, John Linton, Shekhar Acharya
5--
6-- Copyright (c) 2001, 2002, 2003 by Cisco Systems, Inc.
7-- All rights reserved.
8-- *****************************************************************
9--
10-- *****************************************************************
11CISCO-ITP-RT-MIB DEFINITIONS ::= BEGIN
12
13IMPORTS
14        Counter32,
15        Integer32,
16        MODULE-IDENTITY,
17        NOTIFICATION-TYPE,
18        OBJECT-TYPE,
19        Unsigned32
20                FROM SNMPv2-SMI
21
22        TimeStamp,
23        TruthValue
24                FROM SNMPv2-TC
25
26        MODULE-COMPLIANCE,
27        NOTIFICATION-GROUP,
28        OBJECT-GROUP
29                FROM SNMPv2-CONF
30
31        CItpTcLinksetId,
32        CItpTcPointCode,
33        CItpTcQos,
34        CItpTcRouteTableName,
35        CItpTcTableLoadStatus
36                FROM CISCO-ITP-TC-MIB
37
38        ciscoMgmt
39                FROM CISCO-SMI;
40
41ciscoItpRtMIB MODULE-IDENTITY
42        LAST-UPDATED    "200307100000Z"
43        ORGANIZATION    "Cisco Systems, Inc."
44        CONTACT-INFO
45                "       Cisco Systems, Inc
46                        Customer Service
47
48                Postal: 170 W. Tasman Drive
49                        San Jose, CA  95134
50                        USA
51
52                   Tel: +1 800 553-NETS
53
54                E-mail: cs-ss7s@cisco.com"
55        DESCRIPTION
56          "This MIB is for managing information required to
57           route messages transported over Signalling System
58           No. 7 (SS7) Network via Cisco IP Transfer
59           Point.
60
61           The Cisco IP Transfer Point (ITP) is a hardware
62           and software solution that transports SS7 traffic
63           using IP.  Each ITP node provides the functions
64           necessary to act as a SS7 signalling point.  Each
65           signalling point is connected to other signalling
66           point using IP based or traditional TDM links.
67
68           The relevant ITU documents describing this technology
69           are the ITU Q series, including ITU Q.700: Introduction
70           to CCITT Signalling System No. 7 and ITU Q.701
71           Functional description of the message transfer part
72           (MTP) of Signalling System No. 7.
73
74
75           Definitions and overview:
76
77           Route:
78           A route consists of one or more linksets used to transport
79           MTP3 Message Signal Units(MSU) between signalling points.
80           A route is an association between a destination point
81           code(DPC) and a linkset, i.e., a linkset that can be used
82           to send an MSU to the given DPC.
83
84           Routeset:
85           A routeset is a set of routes to a given DPC.  Each route
86           within a routeset is on a possible path toward the DPC.
87           Each route within the routeset has associated with it a
88           route priority.
89
90           In the following simple configuration, two routes exist
91           that can be used to transport MSUs from STP1 to STP4.
92
93             ---------         STP1-STP2         ---------
94             - STP1  ----------------------------- STP2  -
95             ---------                           ---------
96                 |                                   |
97                 | STP1-STP3               STP2-STP4 |
98                 |                                   |
99             ---------         STP3-STP4         ---------
100             - STP3  ----------------------------- STP4  -
101             ---------                           ---------
102
103           Routeset on STP1 for DPC = STP4:
104               STP1-STP2,
105               STP1-STP3
106
107
108           Linkset:
109           A linkset is a set of signalling links connecting
110           two signalling points.
111
112           Combined Linkset:
113           Two linksets with equal number of links and capacity
114           that form routes of equal priority to a given DPC are
115           called Combined Linksets.  It is primarily used for
116           load sharing and redundancy.  In the following, example,
117           linksets 'SSP1-STP1' and 'SSP1-STP2' form a combined
118           linsket.
119
120
121                   SSP1-STP1             ---------
122                |------------------------- STP1  -
123                |                        ---------
124               - -
125             -     -
126            -  SSP1 -
127             -     -
128               - -
129                |  SSP1-STP2            ---------
130                |------------------------ STP2  -
131                                        ---------
132
133           Routing:
134           The routing of SS7 Message signalling Units(MSU) is based
135           on the DPC.  Message Signalling Units are sent from an
136           originating point code(OPC) to DPC.  Each MSU will
137           traverse one or more linksets as it is routed to its
138           final destination.  When an MSU arrives at a signalling
139           point and the DPC does not match the signalling point's
140           point code the MSU must be directed toward the DPC.  Each
141           signalling point has enough routing information to
142           determine which linkset should be used to transmit the
143           MSU toward its final destination.
144
145           Route statement:
146           Each ITP Signalling Point has route statements needed to
147           determine which linkset should be used to transmit
148           message signalling units to destinations.  Each route
149           statement consists of a destination, a priority and a
150           linkset name.  The destination is specified as a
151           combination of DPC and mask.  The priority, also know
152           as cost, is used to define the order in which the routes
153           are selected.  The linkset name specifies which linkset
154           to use to reach the destination.
155
156           Route table:
157           Each ITP Signalling Point has a table of routes.
158           These route entries are used to determine which linkset
159           should be selected to transmit message signalling units
160           to a given destination.
161
162           There are two basic type of routing.  The first type
163           is fully-qualified and uses all bits of the target DPC.
164           The other type is summary routing that uses a subset
165           of the bits in the target DPC and is used to represent
166           groups of point codes rather than a single point code.
167
168           Example of route table entries.
169
170           Example 1: variant = ITU
171
172           DPC/MASK  Priority  Linkset-name
173           --------  --------  -----------------------
174           5.5.5/14  3         STP1-STP2
175           5.5.5/14  7         STP1-STP3
176
177           Description: Two route table entries that define a
178           primary route using linkset 'STP1-STP2' and an alternate
179           route using linkset 'STP1-STP3' to point-code 5.5.5.
180
181           Example 2: variant = ITU
182
183           DPC/MASK  Priority  Linkset-name
184           --------  --------  -----------------------
185           5.5.5/14  3         STP1-STP2
186           5.5.5/14  3         STP1-STP3
187           5.5.5/14  7         STP1-STP4
188
189           Description: Two route table entrys that define a
190           combined linkset consisting of linkset 'STP1-STP2' and
191           'STP1-STP3' to point code 5.5.5.  An alternate route is
192           also defined using linkset 'STP1-STP4'.
193
194           Example 3: variant = ANSI
195
196           DPC/MASK  Priority  Linkset-name
197           --------  --------  -----------------------
198           5.5.0/16  3         STP1-STP2
199
200           Description: A route table entry that defines routing
201           to a cluster.  The cluster represents all point codes
202           in the range from 5.5.0-5.5.255.
203
204           Example 4: variant = ANSI
205
206           DPC/MASK  Priority  Linkset-name
207           --------  --------  -----------------------
208           5.5.0/16  3         STP1-STP3
209           5.5.5/24  3         STP1-STP2
210
211
212           Description: The mixing of fully-qualified and summary
213           route table entrys allow for different routes to be
214           defined for certain DPC in a cluster.  In this
215           configuration, the fully-qualified route will be the
216           primary and the summary route will act as a backup.
217
218           Route table:
219           A group of route table entrys used to route MSU for a
220           particular instance of a signalling point.
221
222           A sample route table.
223
224           DPC/MASK  Priority  Linkset-name
225           --------  --------  -----------------------
226           0.0.0/0   7         STP1-STP4
227           5.5.0/16  3         STP1-STP3
228           5.5.5/24  3         STP1-STP2
229           .
230           .
231           122.5.5   5         STP1-STP2
232           .
233           .
234           243.200.1 6         STP1-STP3
235           "
236
237        REVISION        "200307100000Z"
238        DESCRIPTION
239                "Updated description to provide overview and
240                 additional information.
241
242                 The ability to allow multiple instances of
243                 Signalling Points to run in the same device
244                 has introduce a new index structure.  All
245                 objects in this MIB will be deprecated and
246                 replaced by objects in the CISCO-ITP-GACT-MIB.my
247                 MIB."
248
249
250        REVISION        "200201070000Z"
251        DESCRIPTION
252                "The following objects were added to provide information
253                 on time and status of route table loads using the
254                 file format.
255
256                     cItpRtConfigLoad
257                     cItpRtConfigLoadStatus
258
259                 The following objects were added to provide
260                 information on route state changes.
261
262                     cItpRtStateChangeCount
263                     cItpRtStateChangeNotifEnabled
264                     cItpRtMaxDynamicRoutes
265                     cItpRtChangeNotifWindowTime
266                     cItpRtChangeNotifMaxPerWindow
267                     cItpRtNotifInfoSuppressedFlag
268                     cItpRtNotifInfoStateChanges
269                     cItpRouteStateChange"
270
271        REVISION        "200108290000Z"
272        DESCRIPTION
273                "Initial version of this MIB module."
274        ::= { ciscoMgmt 228 }
275
276-- Top-level structure of the MIB
277
278cItpRouteNotifications     OBJECT IDENTIFIER ::= { ciscoItpRtMIB    0 }
279cItpRtMIBObjects           OBJECT IDENTIFIER ::= { ciscoItpRtMIB    1 }
280cItpRtMIBConformance       OBJECT IDENTIFIER ::= { ciscoItpRtMIB    2 }
281
282
283cItpRtScalars              OBJECT IDENTIFIER ::= { cItpRtMIBObjects 1 }
284cItpRtTables               OBJECT IDENTIFIER ::= { cItpRtMIBObjects 2 }
285cItpRtNotificationsInfo    OBJECT IDENTIFIER ::= { cItpRtMIBObjects 3 }
286
287--  *************************************************************
288--  *                                                           *
289--  * SP - Scalars                                              *
290--  *                                                           *
291--  *************************************************************
292cItpRtConfigLastChanged           OBJECT-TYPE
293    SYNTAX                        TimeStamp
294    MAX-ACCESS                    read-only
295    STATUS                        deprecated
296    DESCRIPTION
297            "The value of sysUpTime at the time of the last
298             creation or deletion of an entry in the cItpRouteTable.
299             If the local network management subsystem is
300             re-initialization, then this object contains the
301             sysUpTime at the time when this occurred. This value
302             can be used to prevent unnecessary walks of the
303             cItpRouteTable."
304    ::= { cItpRtScalars 1 }
305
306cItpRtConfigLoad                  OBJECT-TYPE
307    SYNTAX                        TimeStamp
308    MAX-ACCESS                    read-only
309    STATUS                        deprecated
310    DESCRIPTION
311            "The value of sysUpTime at the time of the last
312             load of the route table using file format."
313    ::= { cItpRtScalars 2 }
314
315cItpRtConfigLoadStatus            OBJECT-TYPE
316    SYNTAX                        CItpTcTableLoadStatus
317    MAX-ACCESS                    read-only
318    STATUS                        deprecated
319    DESCRIPTION
320            "The status of the current load or status from
321             the prior load operation.  This object will have
322             a value of loadInProgress while the load operation
323             is in progress.  The cItpRtConfigLoad contains
324             a timestamp indicating when the load operation
325             completed."
326    ::= { cItpRtScalars 3 }
327
328cItpRtStateChangeCount            OBJECT-TYPE
329    SYNTAX                        Counter32
330    MAX-ACCESS                    read-only
331    STATUS                        deprecated
332    DESCRIPTION
333            "A count of the number of routes that have changed
334             states. This value is incremented whenever the
335             destination state of a route changes.
336             This value is used to provide an indicator
337             of the stability of the routing table information."
338    ::= { cItpRtScalars 4 }
339
340cItpRtStateChangeNotifEnabled    OBJECT-TYPE
341     SYNTAX                      TruthValue
342     MAX-ACCESS                  read-write
343     STATUS                      deprecated
344     DESCRIPTION
345              "A control to enable or disable cItpRouteStateChange
346               notifications as follows:
347             'true'  Indicates that the cItpRouteStateChange
348                     notification should be generated when the state
349                     of any route changes. That is, the notification
350                     generation is enabled.
351             'false' Indicates that cItpRouteStateChange
352                     notification generation is disabled."
353     DEFVAL { false }
354    ::= { cItpRtScalars 5 }
355
356cItpRtChangeNotifDelayTime       OBJECT-TYPE
357    SYNTAX                       Unsigned32 (0..60)
358    UNITS                        "seconds"
359    MAX-ACCESS                   read-write
360    STATUS                       deprecated
361    DESCRIPTION
362        "This object specifies the maximum amount of time to delay
363         before generating the cItpRouteStateChange notification.
364         The delay is introduced to allow multiple route state
365         changes to be bundled into a single notification.
366
367         If the value of this object is equal to 0, the device will
368         generate cItpRouteStateChange notification as each route
369         changes states.
370
371         If the value of this object is greater than 0, the device
372         will not generate notifications as routes change state.
373         As routes changes state they are accumulated until the time
374         specified in cItpRtChangeNotifDelayTime has elapsed or
375         enough state changes have been accumulated to fill up the
376         cItprtNotifInfoStateChanges object.
377
378         This object is ignored by the agent when the
379         cItpRtStateChangeNotifEnabled object is set to the 'false'
380         value."
381     DEFVAL { 10 }
382    ::= { cItpRtScalars  6 }
383
384cItpRtMaxDynamicRoutes           OBJECT-TYPE
385    SYNTAX                       Integer32 (100..1000)
386    MAX-ACCESS                   read-write
387    STATUS                       deprecated
388    DESCRIPTION
389            "The maximum number of dynamic SS7 routes. This
390             object is used to limit the size of the route table
391             by preventing unbounded growth of dynamic entries.
392             Dynamic entries are created when certain MTP3
393             management messages are received or sent. The removal
394             of dynamic routes is performed periodically  and the
395             older dynamic routes are removed until the specified
396             number is reached."
397
398     DEFVAL { 500 }
399    ::= { cItpRtScalars  7 }
400
401cItpRtChangeNotifWindowTime      OBJECT-TYPE
402    SYNTAX                       Integer32 (30..900)
403    UNITS                        "seconds"
404    MAX-ACCESS                   read-write
405    STATUS                       deprecated
406    DESCRIPTION
407        "This object specifies the time interval used to monitor
408         the rate of route state changes notifications.  This object
409         in combination with cItpRtChangeNotifMaxPerWindow are used
410         to determine the notification transit rate and suppress
411         route state notifications."
412     DEFVAL { 60 }
413    ::= { cItpRtScalars  8 }
414
415cItpRtChangeNotifMaxPerWindow    OBJECT-TYPE
416    SYNTAX                       Integer32 (10..9000)
417    MAX-ACCESS                   read-write
418    STATUS                       deprecated
419    DESCRIPTION
420        "This object specifies the maximum number of route
421         state changes that can occur in the time interval
422         specified in the cItpRtChangeNotifMaxPerWindow
423         object.  If additional state changes can occur in
424         the specified time interval the notifications
425         are suppressed."
426     DEFVAL { 60 }
427    ::= { cItpRtScalars  9 }
428
429--  *************************************************************
430--  *                                                           *
431--  * SP - Route Table                                          *
432--  *                                                           *
433--  *************************************************************
434cItpRouteTable                    OBJECT-TYPE
435    SYNTAX                        SEQUENCE OF CItpRouteTableEntry
436    MAX-ACCESS                    not-accessible
437    STATUS                        deprecated
438    DESCRIPTION
439          "The route table for determining the linkset that a
440           packet must traverse to arrive at its destination node
441           given by the destination point code."
442    ::= { cItpRtTables  1 }
443
444cItpRouteTableEntry               OBJECT-TYPE
445    SYNTAX                        CItpRouteTableEntry
446    MAX-ACCESS                    not-accessible
447    STATUS                        deprecated
448    DESCRIPTION
449            "Each table entry represents a configured route
450             statement."
451    INDEX   {
452             cItpRouteTableName,
453             cItpRouteDpc,
454             cItpRouteMask,
455             cItpRouteDestLsCost,
456             cItpRouteDestLinkset
457    }
458    ::= { cItpRouteTable  1 }
459
460CItpRouteTableEntry  ::= SEQUENCE {
461    cItpRouteTableName                CItpTcRouteTableName,
462    cItpRouteDpc                      CItpTcPointCode,
463    cItpRouteDestLsCost               Unsigned32,
464    cItpRouteDestLinkset              CItpTcLinksetId,
465    cItpRouteMask                     Unsigned32,
466    cItpRouteQos                      CItpTcQos,
467    cItpRouteStatus                   INTEGER,
468    cItpRouteNonAdjStatus             INTEGER
469}
470
471cItpRouteTableName                OBJECT-TYPE
472    SYNTAX                        CItpTcRouteTableName
473    MAX-ACCESS                    not-accessible
474    STATUS                        deprecated
475    DESCRIPTION
476            "The configured name for this route table."
477    ::= { cItpRouteTableEntry  1 }
478
479cItpRouteDpc                      OBJECT-TYPE
480    SYNTAX                        CItpTcPointCode
481    MAX-ACCESS                    not-accessible
482    STATUS                        deprecated
483    DESCRIPTION
484            "The destination point code."
485    ::= { cItpRouteTableEntry  2 }
486
487cItpRouteDestLsCost               OBJECT-TYPE
488    SYNTAX                        Unsigned32 (1..9)
489    MAX-ACCESS                    not-accessible
490    STATUS                        deprecated
491    DESCRIPTION
492            "The cost assigned to this linkset matching this
493            route. Higher numbers represent higher cost."
494    ::= { cItpRouteTableEntry  3 }
495
496cItpRouteDestLinkset              OBJECT-TYPE
497    SYNTAX                        CItpTcLinksetId
498    MAX-ACCESS                    not-accessible
499    STATUS                        deprecated
500    DESCRIPTION
501            "The linkset that the packet is to be forwarded to on
502            matching this route."
503    ::= { cItpRouteTableEntry  4 }
504
505cItpRouteMask                     OBJECT-TYPE
506    SYNTAX                        Unsigned32 (0..16777215)
507    MAX-ACCESS                    not-accessible
508    STATUS                        deprecated
509    DESCRIPTION
510            "The mask used to define which part of
511            cItpRouteDpc is significant when comparing
512            the cItpRouteDpc to the destination code
513            point in the packet to be routed."
514    ::= { cItpRouteTableEntry  5 }
515
516cItpRouteQos                      OBJECT-TYPE
517    SYNTAX                        CItpTcQos
518    MAX-ACCESS                    read-only
519    STATUS                        deprecated
520    DESCRIPTION
521            "The quality of service classification to be assigned
522             to the ip packets used to transport the SS7 messages.
523             The value to specify for packets
524             when they will be transported on SCTP/IP based
525             linkset."
526    ::= { cItpRouteTableEntry  6 }
527
528cItpRouteStatus                  OBJECT-TYPE
529    SYNTAX                       INTEGER {
530                                           unknown(1),
531                                           available(2),
532                                           restricted(3),
533                                           unavailable(4)
534                                 }
535    MAX-ACCESS                   read-only
536    STATUS                       deprecated
537    DESCRIPTION
538            "List of the possible route status values.
539                'unknown'     : Status can not be determined.
540                'available'   : Route is available.
541                'restricted'  : Traffic is restricted on route.
542                'unavailable' : Route is unable to service traffic."
543
544    ::= { cItpRouteTableEntry  7 }
545
546cItpRouteNonAdjStatus            OBJECT-TYPE
547    SYNTAX                       INTEGER {
548                                           unknown(1),
549                                           allowed(2),
550                                           restricted(3),
551                                           prohibited(4)
552                                 }
553    MAX-ACCESS                   read-only
554    STATUS                       deprecated
555    DESCRIPTION
556            "List of the possible non-adjacent status values.
557                'unknown'     : Status can not be determined.
558                'allowed'     : traffic is allowed.
559                'restricted'  : Traffic is restricted on route.
560                'prohibited'  : Route is prohibited from providing
561                                traffic."
562    ::= { cItpRouteTableEntry  8 }
563
564
565
566-- *************************************************************
567-- *                                                           *
568-- * Notifications Information                                 *
569-- *                                                           *
570-- *************************************************************
571cItpRtNotifInfoSuppressedFlag OBJECT-TYPE
572     SYNTAX                 TruthValue
573     MAX-ACCESS             read-only
574     STATUS                 deprecated
575     DESCRIPTION
576         "A flag to indicate whether cItpRouteStateChange
577          notifications have been suppressed in the current time
578          interval specified by the cItpRtChangeNotifWindowTime
579          object.
580
581        'true'  Indicates that the device has suppressed the sending
582                of cItpRouteStateChange notifications for the
583                remainder of the time interval.
584
585        'false' Indicates that the device has not suppressed the
586                sending of cItpRouteStateChange notifications in
587                the current time interval."
588    ::= { cItpRtNotificationsInfo 1 }
589
590cItpRtNotifInfoStateChanges OBJECT-TYPE
591     SYNTAX                 OCTET STRING (SIZE(0..480))
592     MAX-ACCESS             read-only
593     STATUS                 deprecated
594     DESCRIPTION
595        "This object contains a list of route state changes
596         accumulated until the list is full or the time
597         time interval specified in cItpRtChangeNotifDelayTime
598         has passed.
599
600         It consists of one or more tuples packed
601         together in the format of '<tuple1><tuple2>...<tuple15>'.
602
603         Each tuple consist of 32 octets in the following format.
604
605         '<cItpRouteTableName>       20 octets null padded
606          <cItpRouteDpc>              4 octets
607          <cItpRouteMask>             4 octets
608          destination status          1 octet
609             1 - unknown state
610             2 - route is accessible
611             3 - route is inaccessible
612             4 - route is restricted'
613          reserved1                   1 octet(set to null)
614          reserved2                   1 octet(set to null)
615          reserved3                   1 octet(set to null)
616
617         The maximum number of tuples is 15."
618    ::= { cItpRtNotificationsInfo 2 }
619-- *************************************************************
620-- *                                                           *
621-- * Notifications                                             *
622-- *                                                           *
623-- *************************************************************
624cItpRouteStateChange NOTIFICATION-TYPE
625     OBJECTS {
626              cItpRtStateChangeCount,
627              cItpRtNotifInfoSuppressedFlag,
628              cItpRtNotifInfoStateChanges
629     }
630     STATUS  deprecated
631     DESCRIPTION
632             "This notification is generated whenever one or more
633              route destination status changes states and includes
634              the count of all route state changes.  This
635              notification contains a list of route state changes
636              in the cItpRtNotifInfoStateChanges object.  State
637              changes are accumulated until the
638              cItpRtNotifInfoStateChanges is full or the maximum
639              delay time is reached.  The delay time is specified
640              by the cItpRtChangeNotifDelayTime object.
641
642              It may be necessary to suppress the sending of
643              notification when a large number route change
644              state, due the failure of some common resource.
645              The number of notifications can be controlled by
646              specifying values for cItpRtChangeNotifWindowTime
647              and cItpRtChangeNotifMaxPerWindow objects. When the
648              number of route state changes exceed the specified
649              value the last notification will indicate that
650              notifications are suppressed for the remainder
651              of the window."
652     ::= { cItpRouteNotifications 1 }
653
654-- *************************************************************
655-- *                                                           *
656-- * Conformance Information                                   *
657-- *                                                           *
658-- *************************************************************
659cItpRtMIBCompliances OBJECT IDENTIFIER ::=
660        { cItpRtMIBConformance 1 }
661cItpRtMIBGroups      OBJECT IDENTIFIER ::=
662        { cItpRtMIBConformance 2 }
663
664-- Compliance
665
666cItpRtMIBCompliance MODULE-COMPLIANCE
667    STATUS deprecated -- superceded by cItpRtMIBComplianceRev1
668    DESCRIPTION
669            "The compliance statement for entities which implement
670            the Cisco CISCO-ITP-RT-MIB.my MIB"
671    MODULE -- this module
672            MANDATORY-GROUPS {
673                    cItpRtScalarGroup,
674                    cItpRouteGroup
675            }
676    ::= { cItpRtMIBCompliances 1 }
677
678cItpRtMIBComplianceRev1 MODULE-COMPLIANCE
679    STATUS deprecated
680    DESCRIPTION
681            "The compliance statement for entities which implement
682             the Cisco CISCO-ITP-RT-MIB.my MIB"
683    MODULE -- this module
684            MANDATORY-GROUPS {
685                    cItpRtScalarGroup,
686                    cItpRouteGroup,
687                    cItpRtNotificationsGroup,
688                    cItpRtScalarGroupRev1
689            }
690    ::= { cItpRtMIBCompliances 2 }
691
692-- Units of Conformance
693
694cItpRtScalarGroup OBJECT-GROUP
695    OBJECTS {
696             cItpRtConfigLastChanged
697    }
698    STATUS deprecated
699    DESCRIPTION
700            "Route scalars Group."
701    ::= { cItpRtMIBGroups 1 }
702
703cItpRouteGroup OBJECT-GROUP
704    OBJECTS {
705             cItpRouteQos,
706             cItpRouteStatus,
707             cItpRouteNonAdjStatus
708    }
709    STATUS deprecated
710    DESCRIPTION
711            "Route table group."
712    ::= { cItpRtMIBGroups 2 }
713
714
715
716cItpRtNotificationsGroup NOTIFICATION-GROUP
717        NOTIFICATIONS {
718                cItpRouteStateChange
719        }
720        STATUS deprecated
721        DESCRIPTION
722                "Route notification objects."
723    ::= { cItpRtMIBGroups 3 }
724
725cItpRtScalarGroupRev1 OBJECT-GROUP
726    OBJECTS {
727             cItpRtConfigLoad,
728             cItpRtConfigLoadStatus,
729             cItpRtStateChangeCount,
730             cItpRtStateChangeNotifEnabled,
731             cItpRtChangeNotifDelayTime,
732             cItpRtMaxDynamicRoutes,
733             cItpRtChangeNotifWindowTime,
734             cItpRtChangeNotifMaxPerWindow,
735             cItpRtNotifInfoSuppressedFlag,
736             cItpRtNotifInfoStateChanges
737
738    }
739    STATUS deprecated
740    DESCRIPTION
741            "Route revision one scalars group."
742    ::= { cItpRtMIBGroups 4 }
743END
744