1 /*
2 * Copyright (C) 2014, Barco (www.barco.com)
3 * Copyright (C) 2014 Stefan Roese <sr@denx.de>
4 *
5 * SPDX-License-Identifier: GPL-2.0+
6 */
7
8 #include <common.h>
9 #include <asm/gpio.h>
10 #include <asm/io.h>
11 #include <asm/arch/clock.h>
12 #include <asm/arch/iomux.h>
13 #include <asm/arch/mx6-pins.h>
14 #include <asm/imx-common/iomux-v3.h>
15 #include <asm/imx-common/mxc_i2c.h>
16 #include <i2c.h>
17 #include <miiphy.h>
18
19 #include "platinum.h"
20
21 #define GPIO_IP_NCONFIG IMX_GPIO_NR(5, 18)
22 #define GPIO_HK_NCONFIG IMX_GPIO_NR(7, 13)
23 #define GPIO_LS_NCONFIG IMX_GPIO_NR(5, 19)
24
25 #define GPIO_I2C0_SEL0 IMX_GPIO_NR(5, 2)
26 #define GPIO_I2C0_SEL1 IMX_GPIO_NR(1, 11)
27 #define GPIO_I2C0_ENBN IMX_GPIO_NR(1, 13)
28
29 #define GPIO_I2C2_SEL0 IMX_GPIO_NR(1, 17)
30 #define GPIO_I2C2_SEL1 IMX_GPIO_NR(1, 20)
31 #define GPIO_I2C2_ENBN IMX_GPIO_NR(1, 14)
32
33 #define GPIO_USB_RESET IMX_GPIO_NR(1, 5)
34
35 iomux_v3_cfg_t const ecspi1_pads[] = {
36 MX6_PAD_EIM_D16__ECSPI1_SCLK | MUX_PAD_CTRL(ECSPI1_PAD_CLK),
37 MX6_PAD_EIM_D17__ECSPI1_MISO | MUX_PAD_CTRL(ECSPI_PAD_MISO),
38 MX6_PAD_EIM_D18__ECSPI1_MOSI | MUX_PAD_CTRL(ECSPI_PAD_MOSI),
39 MX6_PAD_CSI0_DAT7__ECSPI1_SS0 | MUX_PAD_CTRL(ECSPI_PAD_SS),
40 MX6_PAD_EIM_D24__ECSPI1_SS2 | MUX_PAD_CTRL(ECSPI_PAD_SS),
41 MX6_PAD_EIM_D25__ECSPI1_SS3 | MUX_PAD_CTRL(ECSPI_PAD_SS),
42 };
43
44 iomux_v3_cfg_t const ecspi2_pads[] = {
45 MX6_PAD_EIM_CS0__ECSPI2_SCLK | MUX_PAD_CTRL(ECSPI2_PAD_CLK),
46 MX6_PAD_EIM_OE__ECSPI2_MISO | MUX_PAD_CTRL(ECSPI_PAD_MISO),
47 MX6_PAD_EIM_CS1__ECSPI2_MOSI | MUX_PAD_CTRL(ECSPI_PAD_MOSI),
48 MX6_PAD_EIM_RW__ECSPI2_SS0 | MUX_PAD_CTRL(ECSPI_PAD_SS),
49 MX6_PAD_EIM_LBA__ECSPI2_SS1 | MUX_PAD_CTRL(ECSPI_PAD_SS),
50 };
51
52 iomux_v3_cfg_t const enet_pads[] = {
53 MX6_PAD_ENET_MDIO__ENET_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL),
54 MX6_PAD_ENET_MDC__ENET_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL),
55 MX6_PAD_ENET_CRS_DV__ENET_RX_EN | MUX_PAD_CTRL(ENET_PAD_CTRL),
56 MX6_PAD_GPIO_16__ENET_REF_CLK | MUX_PAD_CTRL(ENET_PAD_CTRL),
57 MX6_PAD_ENET_RX_ER__ENET_RX_ER | MUX_PAD_CTRL(ENET_PAD_CTRL),
58 MX6_PAD_ENET_RXD0__ENET_RX_DATA0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
59 MX6_PAD_ENET_RXD1__ENET_RX_DATA1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
60 MX6_PAD_ENET_TX_EN__ENET_TX_EN | MUX_PAD_CTRL(ENET_PAD_CTRL),
61 MX6_PAD_ENET_TXD0__ENET_TX_DATA0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
62 MX6_PAD_ENET_TXD1__ENET_TX_DATA1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
63 };
64
65 /* PHY nRESET */
66 iomux_v3_cfg_t const phy_reset_pad = {
67 MX6_PAD_SD1_DAT2__GPIO1_IO19 | MUX_PAD_CTRL(NO_PAD_CTRL),
68 };
69
70 iomux_v3_cfg_t const uart1_pads[] = {
71 MX6_PAD_SD3_DAT6__UART1_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
72 MX6_PAD_SD3_DAT7__UART1_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
73 };
74
75 iomux_v3_cfg_t const uart4_pads[] = {
76 MX6_PAD_CSI0_DAT12__UART4_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
77 MX6_PAD_CSI0_DAT13__UART4_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
78 MX6_PAD_CSI0_DAT16__UART4_RTS_B | MUX_PAD_CTRL(UART_PAD_CTRL),
79 MX6_PAD_CSI0_DAT17__UART4_CTS_B | MUX_PAD_CTRL(UART_PAD_CTRL),
80 };
81
82 iomux_v3_cfg_t const uart5_pads[] = {
83 MX6_PAD_CSI0_DAT14__UART5_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
84 MX6_PAD_CSI0_DAT15__UART5_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
85 MX6_PAD_CSI0_DAT18__UART5_RTS_B | MUX_PAD_CTRL(UART_PAD_CTRL),
86 MX6_PAD_CSI0_DAT19__UART5_CTS_B | MUX_PAD_CTRL(UART_PAD_CTRL),
87 };
88
89 iomux_v3_cfg_t const i2c0_mux_pads[] = {
90 MX6_PAD_EIM_A25__GPIO5_IO02 | MUX_PAD_CTRL(NO_PAD_CTRL),
91 MX6_PAD_SD2_CMD__GPIO1_IO11 | MUX_PAD_CTRL(NO_PAD_CTRL),
92 MX6_PAD_SD2_DAT2__GPIO1_IO13 | MUX_PAD_CTRL(NO_PAD_CTRL),
93 };
94
95 iomux_v3_cfg_t const i2c2_mux_pads[] = {
96 MX6_PAD_SD1_DAT1__GPIO1_IO17 | MUX_PAD_CTRL(NO_PAD_CTRL),
97 MX6_PAD_SD1_CLK__GPIO1_IO20 | MUX_PAD_CTRL(NO_PAD_CTRL),
98 MX6_PAD_SD2_DAT1__GPIO1_IO14 | MUX_PAD_CTRL(NO_PAD_CTRL),
99 };
100
101 struct i2c_pads_info i2c_pad_info0 = {
102 .scl = {
103 .i2c_mode = MX6_PAD_CSI0_DAT9__I2C1_SCL | PC_SCL,
104 .gpio_mode = MX6_PAD_CSI0_DAT9__GPIO5_IO27 | PC_SCL,
105 .gp = IMX_GPIO_NR(5, 27)
106 },
107 .sda = {
108 .i2c_mode = MX6_PAD_CSI0_DAT8__I2C1_SDA | PC,
109 .gpio_mode = MX6_PAD_CSI0_DAT8__GPIO5_IO26 | PC,
110 .gp = IMX_GPIO_NR(5, 26)
111 }
112 };
113
114 struct i2c_pads_info i2c_pad_info2 = {
115 .scl = {
116 .i2c_mode = MX6_PAD_GPIO_3__I2C3_SCL | PC_SCL,
117 .gpio_mode = MX6_PAD_GPIO_3__GPIO1_IO03 | PC_SCL,
118 .gp = IMX_GPIO_NR(1, 3)
119 },
120 .sda = {
121 .i2c_mode = MX6_PAD_GPIO_6__I2C3_SDA | PC,
122 .gpio_mode = MX6_PAD_GPIO_6__GPIO1_IO06 | PC,
123 .gp = IMX_GPIO_NR(1, 6)
124 }
125 };
126
127 /*
128 * This enet related pin-muxing and GPIO handling is done
129 * in SPL U-Boot. For early initialization. And to give the
130 * PHY some time to come out of reset before the U-Boot
131 * ethernet driver tries to access its registers via MDIO.
132 */
platinum_setup_enet(void)133 int platinum_setup_enet(void)
134 {
135 struct iomuxc *iomux = (struct iomuxc *)IOMUXC_BASE_ADDR;
136 unsigned phy_reset = IMX_GPIO_NR(1, 19);
137
138 /* First configure PHY reset GPIO pin */
139 imx_iomux_v3_setup_pad(phy_reset_pad);
140
141 /* Reconfigure enet muxing while PHY is in reset */
142 gpio_direction_output(phy_reset, 0);
143 imx_iomux_v3_setup_multiple_pads(enet_pads, ARRAY_SIZE(enet_pads));
144 mdelay(10);
145 gpio_set_value(phy_reset, 1);
146 udelay(100);
147
148 /* set GPIO_16 as ENET_REF_CLK_OUT */
149 setbits_le32(&iomux->gpr[1], IOMUXC_GPR1_ENET_CLK_SEL_MASK);
150
151 return enable_fec_anatop_clock(ENET_50MHZ);
152 }
153
platinum_setup_i2c(void)154 int platinum_setup_i2c(void)
155 {
156 imx_iomux_v3_setup_multiple_pads(i2c0_mux_pads,
157 ARRAY_SIZE(i2c0_mux_pads));
158 imx_iomux_v3_setup_multiple_pads(i2c2_mux_pads,
159 ARRAY_SIZE(i2c2_mux_pads));
160
161 mdelay(10);
162
163 /* Disable i2c mux 0 */
164 gpio_direction_output(GPIO_I2C0_SEL0, 0);
165 gpio_direction_output(GPIO_I2C0_SEL1, 0);
166 gpio_direction_output(GPIO_I2C0_ENBN, 1);
167
168 /* Disable i2c mux 1 */
169 gpio_direction_output(GPIO_I2C2_SEL0, 0);
170 gpio_direction_output(GPIO_I2C2_SEL1, 0);
171 gpio_direction_output(GPIO_I2C2_ENBN, 1);
172
173 udelay(10);
174
175 setup_i2c(0, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info0);
176 setup_i2c(2, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info2);
177
178 /* Disable all leds */
179 i2c_set_bus_num(0);
180 i2c_reg_write(0x60, 0x05, 0x55);
181
182 return 0;
183 }
184
platinum_setup_spi(void)185 int platinum_setup_spi(void)
186 {
187 imx_iomux_v3_setup_multiple_pads(ecspi1_pads, ARRAY_SIZE(ecspi1_pads));
188 imx_iomux_v3_setup_multiple_pads(ecspi2_pads, ARRAY_SIZE(ecspi2_pads));
189
190 return 0;
191 }
192
platinum_setup_uart(void)193 int platinum_setup_uart(void)
194 {
195 imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads));
196 imx_iomux_v3_setup_multiple_pads(uart4_pads, ARRAY_SIZE(uart4_pads));
197 imx_iomux_v3_setup_multiple_pads(uart5_pads, ARRAY_SIZE(uart5_pads));
198
199 return 0;
200 }
201
platinum_phy_config(struct phy_device * phydev)202 int platinum_phy_config(struct phy_device *phydev)
203 {
204 /* Use generic infrastructure, no specific setup */
205 if (phydev->drv->config)
206 phydev->drv->config(phydev);
207
208 return 0;
209 }
210
platinum_init_gpio(void)211 int platinum_init_gpio(void)
212 {
213 /* Reset FPGA's */
214 gpio_direction_output(GPIO_IP_NCONFIG, 0);
215 gpio_direction_output(GPIO_HK_NCONFIG, 0);
216 gpio_direction_output(GPIO_LS_NCONFIG, 0);
217 udelay(3);
218 gpio_set_value(GPIO_IP_NCONFIG, 1);
219 gpio_set_value(GPIO_HK_NCONFIG, 1);
220 gpio_set_value(GPIO_LS_NCONFIG, 1);
221
222 /* no dmd configuration yet */
223
224 return 0;
225 }
226
platinum_init_usb(void)227 int platinum_init_usb(void)
228 {
229 /* Reset usb hub */
230 gpio_direction_output(GPIO_USB_RESET, 0);
231 udelay(100);
232 gpio_set_value(GPIO_USB_RESET, 1);
233
234 return 0;
235 }
236
platinum_init_finished(void)237 int platinum_init_finished(void)
238 {
239 /* Enable led 0 */
240 i2c_set_bus_num(0);
241 i2c_reg_write(0x60, 0x05, 0x54);
242
243 return 0;
244 }
245