1// SPDX-License-Identifier: GPL-2.0-only
2/*
3 * Device Tree Source for IGEP COM MODULE Rev. G (TI OMAP AM/DM37x)
4 *
5 * Copyright (C) 2014 Javier Martinez Canillas <javier@dowhile0.org>
6 * Copyright (C) 2014 Enric Balletbo i Serra <eballetbo@gmail.com>
7 */
8
9#include "omap3-igep0030-common.dtsi"
10
11/ {
12	model = "IGEP COM MODULE Rev. G (TI OMAP AM/DM37x)";
13	compatible = "isee,omap3-igep0030-rev-g", "ti,omap3630", "ti,omap36xx", "ti,omap3";
14
15	/* Regulator to trigger the WL_EN signal of the Wifi module */
16	lbep5clwmc_wlen: regulator-lbep5clwmc-wlen {
17		compatible = "regulator-fixed";
18		regulator-name = "regulator-lbep5clwmc-wlen";
19		regulator-min-microvolt = <3300000>;
20		regulator-max-microvolt = <3300000>;
21		gpio = <&gpio5 11 GPIO_ACTIVE_HIGH>;		/* gpio_139 - WL_EN */
22		enable-active-high;
23	};
24};
25
26&omap3_pmx_core {
27	lbep5clwmc_pins: pinmux_lbep5clwmc_pins {
28		pinctrl-single,pins = <
29			OMAP3_CORE1_IOPAD(0x2164, PIN_INPUT | MUX_MODE4)	/* sdmmc2_dat4.gpio_136 - W_IRQ */
30			OMAP3_CORE1_IOPAD(0x2166, PIN_OUTPUT | MUX_MODE4)	/* sdmmc2_dat5.gpio_137 - BT_EN */
31			OMAP3_CORE1_IOPAD(0x216a, PIN_OUTPUT | MUX_MODE4)	/* sdmmc2_dat7.gpio_139 - WL_EN */
32		>;
33	};
34
35	leds_pins: pinmux_leds_pins {
36		pinctrl-single,pins = <
37			OMAP3_CORE1_IOPAD(0x21be, PIN_OUTPUT | MUX_MODE4)	/* i2c2_scl.gpio_168 */
38		>;
39	};
40
41};
42
43&i2c2 {
44	status = "disabled";
45};
46
47&leds {
48	pinctrl-names = "default";
49	pinctrl-0 = <&leds_pins &leds_core2_pins>;
50
51	boot {
52		label = "omap3:green:boot";
53		gpios = <&gpio6 8 GPIO_ACTIVE_HIGH>;
54		default-state = "on";
55	};
56};
57
58&mmc2 {
59	pinctrl-names = "default";
60	pinctrl-0 = <&mmc2_pins &lbep5clwmc_pins>;
61	vmmc-supply = <&lbep5clwmc_wlen>;
62	bus-width = <4>;
63	non-removable;
64
65	#address-cells = <1>;
66	#size-cells = <0>;
67	wlcore: wlcore@2 {
68		compatible = "ti,wl1835";
69		reg = <2>;
70		interrupt-parent = <&gpio5>;
71		interrupts = <8 IRQ_TYPE_EDGE_RISING>; /* gpio 136 */
72	};
73};
74
75&uart2 {
76	bluetooth {
77		compatible = "ti,wl1835-st";
78		enable-gpios = <&gpio5 9 GPIO_ACTIVE_HIGH>; /* gpio 137 */
79		max-speed = <300000>;
80	};
81};
82