1ATM2-MIB DEFINITIONS ::= BEGIN 2 3 IMPORTS 4 MODULE-IDENTITY, OBJECT-TYPE, NOTIFICATION-TYPE, 5 Gauge32, Counter32, Integer32 6 FROM SNMPv2-SMI 7 TruthValue, RowStatus, TimeStamp 8 FROM SNMPv2-TC 9 MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP 10 FROM SNMPv2-CONF 11 SnmpAdminString 12 FROM SNMP-FRAMEWORK-MIB 13 InterfaceIndex, InterfaceIndexOrZero, ifIndex 14 FROM IF-MIB 15 atmMIBObjects, atmInterfaceConfEntry, 16 atmVplEntry, atmVplVpi, 17 atmVclEntry, atmVclVpi, atmVclVci, 18 19 20 21 atmVpCrossConnectEntry, atmVcCrossConnectEntry 22 FROM ATM-MIB 23 AtmAddr, AtmSigDescrParamIndex, 24 AtmInterfaceType, AtmIlmiNetworkPrefix, 25 AtmVcIdentifier, AtmVpIdentifier, 26 AtmTrafficDescrParamIndex 27 FROM ATM-TC-MIB; 28 29 atm2MIB MODULE-IDENTITY 30 LAST-UPDATED "200309230000Z" 31 ORGANIZATION "IETF AToMMIB Working Group" 32 CONTACT-INFO 33 "AToMMIB WG 34 http://www.ietf.org/html.charters/atommib-charter.html 35 Editors: 36 Faye Ly 37 Postal: Pedestal Networks 38 6503 Dumbarton Circle 39 Fremont, CA 94555 40 USA 41 Tel: +1 510 896 2908 42 E-Mail: faye@pedestalnetworks.com 43 44 Michael Noto 45 Postal: Cisco Systems 46 170 W. Tasman Drive 47 San Jose, CA 95134-1706 48 USA 49 50 E-mail: mnoto@cisco.com 51 52 Andrew Smith 53 Postal: Consultant 54 55 E-Mail: ah_smith@acm.org 56 57 Ethan Mickey Spiegel 58 Postal: Cisco Systems 59 170 W. Tasman Drive 60 San Jose, CA 95134-1706 61 USA 62 Tel: +1 408 526 6408 63 Fax: +1 408 526 6488 64 E-Mail: mspiegel@cisco.com 65 66 Kaj Tesink 67 Postal: Telcordia Technologies 68 331 Newman Springs Road 69 70 71 72 Red Bank, NJ 07701 73 USA 74 Tel: +1 732 758 5254 75 E-mail: kaj@research.telcordia.com" 76 DESCRIPTION 77 "Copyright (C) The Internet Society (2003). This version of 78 this MIB module is part of RFC 3606; see the RFC itself for 79 full legal notices. 80 81 This MIB Module is a supplement to the ATM-MIB 82 defined in RFC 2515." 83 REVISION "200309230000Z" 84 DESCRIPTION 85 "Initial version of this MIB, published as RFC 3606." 86 87 ::= { atmMIBObjects 14 } 88 89 atm2MIBObjects OBJECT IDENTIFIER ::= {atm2MIB 1} 90 91 atm2MIBTraps OBJECT IDENTIFIER ::= {atm2MIB 2} 92 93 -- This ATM2-MIB Module consists of the following tables, 94 -- plus ATM trap support: 95 -- 1. atmSvcVpCrossConnectTable 96 -- 2. atmSvcVcCrossConnectTable 97 -- 3. atmSigStatTable 98 -- 4. atmSigSupportTable 99 -- 5. atmSigDescrParamTable 100 -- 6. atmIfRegisteredAddrTable 101 -- 7. atmVclAddrTable 102 -- 8. atmAddrVclTable 103 -- 9. atmVplStatTable 104 -- 10. atmVplLogicalPortTable 105 -- 11. atmVclStatTable 106 -- 12. atmAal5VclStatTable 107 -- 13. atmVclGenTable 108 -- 14. atmInterfaceExtTable 109 -- 15. atmIlmiSrvcRegTable 110 -- 16. atmIlmiNetworkPrefixTable 111 -- 17. atmSwitchAddressTable 112 -- 18. atmVpCrossConnectXTable 113 -- 19. atmVcCrossConnectXTable 114 -- 20. atmCurrentlyFailingPVplTable 115 -- 21. atmCurrentlyFailingPVclTable 116 117 -- 1. ATM VPL SVC Cross-Connect Table 118 119 atmSvcVpCrossConnectTable OBJECT-TYPE 120 121 122 123 SYNTAX SEQUENCE OF 124 AtmSvcVpCrossConnectEntry 125 MAX-ACCESS not-accessible 126 STATUS current 127 DESCRIPTION 128 "The ATM SVPC Cross-Connect table. A 129 bi-directional VP cross-connect between two 130 switched VPLs is modeled as one entry in this 131 table. A Soft PVPC cross-connect, between a 132 soft permanent VPL and a switched VPL, is 133 also modeled as one entry in this table." 134 ::= { atm2MIBObjects 1 } 135 136 atmSvcVpCrossConnectEntry OBJECT-TYPE 137 SYNTAX AtmSvcVpCrossConnectEntry 138 MAX-ACCESS not-accessible 139 STATUS current 140 DESCRIPTION 141 "An entry in the ATM SVPC Cross-Connect table. 142 This entry is used to model a bi-directional 143 ATM VP cross-connect between two VPLs." 144 INDEX { atmSvcVpCrossConnectIndex, 145 atmSvcVpCrossConnectLowIfIndex, 146 atmSvcVpCrossConnectLowVpi, 147 atmSvcVpCrossConnectHighIfIndex, 148 atmSvcVpCrossConnectHighVpi } 149 ::= { atmSvcVpCrossConnectTable 1 } 150 151 AtmSvcVpCrossConnectEntry ::= SEQUENCE { 152 atmSvcVpCrossConnectIndex INTEGER, 153 atmSvcVpCrossConnectLowIfIndex InterfaceIndex, 154 atmSvcVpCrossConnectLowVpi AtmVpIdentifier, 155 atmSvcVpCrossConnectHighIfIndex InterfaceIndex, 156 atmSvcVpCrossConnectHighVpi AtmVpIdentifier, 157 atmSvcVpCrossConnectCreationTime TimeStamp, 158 atmSvcVpCrossConnectRowStatus RowStatus 159 } 160 161 atmSvcVpCrossConnectIndex OBJECT-TYPE 162 SYNTAX INTEGER (1..2147483647) 163 MAX-ACCESS not-accessible 164 STATUS current 165 DESCRIPTION 166 "A unique value to identify this SVPC 167 cross-connect. For each VP associated 168 with this cross-connect, the agent reports 169 this cross-connect index value in the 170 atmVplCrossConnectIdentifer attribute of the 171 172 173 174 corresponding atmVplTable entries." 175 ::= { atmSvcVpCrossConnectEntry 1 } 176 177 atmSvcVpCrossConnectLowIfIndex OBJECT-TYPE 178 SYNTAX InterfaceIndex 179 MAX-ACCESS not-accessible 180 STATUS current 181 DESCRIPTION 182 "The value of this object is equal to the 183 ifIndex value of the ATM interface port for this 184 SVPC cross-connect. The term low implies 185 that this ATM interface has the numerically lower 186 ifIndex value than the other ATM interface 187 identified in the same atmSvcVpCrossConnectEntry." 188 ::= { atmSvcVpCrossConnectEntry 2 } 189 190 atmSvcVpCrossConnectLowVpi OBJECT-TYPE 191 SYNTAX AtmVpIdentifier 192 MAX-ACCESS not-accessible 193 STATUS current 194 DESCRIPTION 195 "The value of this object is equal to the VPI 196 value associated with the SVPC cross-connect 197 at the ATM interface that is identified by 198 atmSvcVpCrossConnectLowIfIndex. The VPI value 199 cannot exceed the number supported by the 200 atmInterfaceCurrentMaxSvpcVpi at the low ATM interface 201 port." 202 ::= { atmSvcVpCrossConnectEntry 3 } 203 204 atmSvcVpCrossConnectHighIfIndex OBJECT-TYPE 205 SYNTAX InterfaceIndex 206 MAX-ACCESS not-accessible 207 STATUS current 208 DESCRIPTION 209 "The value of this object is equal to the 210 ifIndex value of the ATM interface port for 211 this SVC VP cross-connect. The term high 212 implies that this ATM interface has the 213 numerically higher ifIndex value than the 214 other ATM interface identified in the same 215 atmSvcVpCrossConnectEntry." 216 ::= { atmSvcVpCrossConnectEntry 4 } 217 218 atmSvcVpCrossConnectHighVpi OBJECT-TYPE 219 SYNTAX AtmVpIdentifier 220 MAX-ACCESS not-accessible 221 STATUS current 222 223 224 225 DESCRIPTION 226 "The value of this object is equal to the VPI 227 value associated with the SVPC cross-connect 228 at the ATM interface that is identified by 229 atmSvcVpCrossConnectHighIfIndex. The VPI value 230 cannot exceed the number supported by the 231 atmInterfaceCurrentMaxSvpcVpi at the high ATM interface 232 port." 233 ::= { atmSvcVpCrossConnectEntry 5 } 234 235 atmSvcVpCrossConnectCreationTime OBJECT-TYPE 236 SYNTAX TimeStamp 237 MAX-ACCESS read-only 238 STATUS current 239 DESCRIPTION 240 "The value of the sysUpTime object 241 at the time this bi-directional SVPC 242 cross-connect was created. If the current 243 state was entered prior to the last 244 re-initialization of the agent, then this 245 object contains a zero value." 246 ::= { atmSvcVpCrossConnectEntry 6 } 247 248 atmSvcVpCrossConnectRowStatus OBJECT-TYPE 249 SYNTAX RowStatus 250 MAX-ACCESS read-write 251 STATUS current 252 DESCRIPTION 253 "This object is used to delete rows in the 254 atmSvcVpCrossConnectTable." 255 ::= { atmSvcVpCrossConnectEntry 7 } 256 257 -- 2. ATM VCL SVC Cross-Connect Table 258 259 atmSvcVcCrossConnectTable OBJECT-TYPE 260 SYNTAX SEQUENCE OF AtmSvcVcCrossConnectEntry 261 MAX-ACCESS not-accessible 262 STATUS current 263 DESCRIPTION 264 "The ATM SVCC Cross-Connect table. A 265 bi-directional VC cross-connect between two 266 switched VCLs is modeled as one entry in 267 this table. A Soft PVCC cross-connect, 268 between a soft permanent VCL and a switched 269 VCL, is also modeled as one entry in this 270 table." 271 ::= { atm2MIBObjects 2 } 272 273 274 275 276 atmSvcVcCrossConnectEntry OBJECT-TYPE 277 SYNTAX AtmSvcVcCrossConnectEntry 278 MAX-ACCESS not-accessible 279 STATUS current 280 DESCRIPTION 281 "An entry in the ATM SVCC Cross-Connect table. 282 This entry is used to model a bi-directional ATM 283 VC cross-connect between two VCLs." 284 INDEX { atmSvcVcCrossConnectIndex, 285 atmSvcVcCrossConnectLowIfIndex, 286 atmSvcVcCrossConnectLowVpi, 287 atmSvcVcCrossConnectLowVci, 288 atmSvcVcCrossConnectHighIfIndex, 289 atmSvcVcCrossConnectHighVpi, 290 atmSvcVcCrossConnectHighVci } 291 ::= { atmSvcVcCrossConnectTable 1 } 292 293 AtmSvcVcCrossConnectEntry ::= SEQUENCE { 294 atmSvcVcCrossConnectIndex INTEGER, 295 atmSvcVcCrossConnectLowIfIndex InterfaceIndex, 296 atmSvcVcCrossConnectLowVpi AtmVpIdentifier, 297 atmSvcVcCrossConnectLowVci AtmVcIdentifier, 298 atmSvcVcCrossConnectHighIfIndex InterfaceIndex, 299 atmSvcVcCrossConnectHighVpi AtmVpIdentifier, 300 atmSvcVcCrossConnectHighVci AtmVcIdentifier, 301 atmSvcVcCrossConnectCreationTime TimeStamp, 302 atmSvcVcCrossConnectRowStatus RowStatus 303 } 304 305 atmSvcVcCrossConnectIndex OBJECT-TYPE 306 SYNTAX INTEGER (1..2147483647) 307 MAX-ACCESS not-accessible 308 STATUS current 309 DESCRIPTION 310 "A unique value to identify this SVCC cross-connect. 311 For each VP associated with this cross-connect, the 312 agent reports this cross-connect index value in the 313 atmVclCrossConnectIdentifier attribute of the 314 corresponding atmVplTable entries." 315 ::= { atmSvcVcCrossConnectEntry 1 } 316 317 atmSvcVcCrossConnectLowIfIndex OBJECT-TYPE 318 SYNTAX InterfaceIndex 319 MAX-ACCESS not-accessible 320 STATUS current 321 DESCRIPTION 322 "The value of this object is equal to the 323 ifIndex value of the ATM interface port for this 324 325 326 327 SVCC cross-connect. The term low implies that 328 this ATM interface has the numerically lower 329 ifIndex value than the other ATM interface 330 identified in the same atmSvcVcCrossConnectEntry." 331 ::= { atmSvcVcCrossConnectEntry 2 } 332 333 atmSvcVcCrossConnectLowVpi OBJECT-TYPE 334 SYNTAX AtmVpIdentifier 335 MAX-ACCESS not-accessible 336 STATUS current 337 DESCRIPTION 338 "The value of this object is equal to the VPI 339 value associated with the SVCC cross-connect 340 at the ATM interface that is identified by 341 atmSvcVcCrossConnectLowIfIndex. The VPI value 342 cannot exceed the number supported by the 343 atmInterfaceCurrentMaxSvccVpi at the low ATM interface 344 port." 345 ::= { atmSvcVcCrossConnectEntry 3 } 346 347 atmSvcVcCrossConnectLowVci OBJECT-TYPE 348 SYNTAX AtmVcIdentifier 349 MAX-ACCESS not-accessible 350 STATUS current 351 DESCRIPTION 352 "The value of this object is equal to the VCI 353 value associated with the SVCC cross-connect 354 at the ATM interface that is identified by 355 atmSvcVcCrossConnectLowIfIndex. The VCI value 356 cannot exceed the number supported by the 357 atmInterfaceCurrentMaxSvccVci at the low ATM interface 358 port." 359 ::= { atmSvcVcCrossConnectEntry 4 } 360 361 atmSvcVcCrossConnectHighIfIndex OBJECT-TYPE 362 SYNTAX InterfaceIndex 363 MAX-ACCESS not-accessible 364 STATUS current 365 DESCRIPTION 366 "The value of this object is equal to the 367 ifIndex value for the ATM interface port for 368 this SVCC cross-connect. The term high implies 369 that this ATM interface has the numerically 370 higher ifIndex value than the other ATM interface 371 identified in the same atmSvcVcCrossConnectEntry." 372 ::= { atmSvcVcCrossConnectEntry 5 } 373 374 atmSvcVcCrossConnectHighVpi OBJECT-TYPE 375 376 377 378 SYNTAX AtmVpIdentifier 379 MAX-ACCESS not-accessible 380 STATUS current 381 DESCRIPTION 382 "The value of this object is equal to the VPI 383 value associated with the SVCC cross-connect 384 at the ATM interface that is identified by 385 atmSvcVcCrossConnectHighIfIndex. The VPI value 386 cannot exceed the number supported by the 387 atmInterfaceCurrentMaxSvccVpi at the high ATM interface 388 port." 389 ::= { atmSvcVcCrossConnectEntry 6 } 390 391 atmSvcVcCrossConnectHighVci OBJECT-TYPE 392 SYNTAX AtmVcIdentifier 393 MAX-ACCESS not-accessible 394 STATUS current 395 DESCRIPTION 396 "The value of this object is equal to the VCI 397 value associated with the SVCC cross-connect 398 at the ATM interface that is identified by 399 atmSvcVcCrossConnectHighIfIndex. The VCI value 400 cannot exceed the number supported by the 401 atmInterfaceMaxVciBits at the high ATM interface 402 port." 403 ::= { atmSvcVcCrossConnectEntry 7 } 404 405 atmSvcVcCrossConnectCreationTime OBJECT-TYPE 406 SYNTAX TimeStamp 407 MAX-ACCESS read-only 408 STATUS current 409 DESCRIPTION 410 "The value of the sysUpTime object 411 at the time this bi-directional SVCC 412 cross-connect was created. If the current 413 state was entered prior to the last 414 re-initialization of the agent, then this 415 object contains a zero value." 416 ::= { atmSvcVcCrossConnectEntry 8 } 417 418 atmSvcVcCrossConnectRowStatus OBJECT-TYPE 419 SYNTAX RowStatus 420 MAX-ACCESS read-write 421 STATUS current 422 DESCRIPTION 423 "This object is used to delete rows in the 424 atmSvcVcCrossConnectTable." 425 ::= { atmSvcVcCrossConnectEntry 9 } 426 427 428 429 -- 3. ATM Interface Signalling Statistics Table -- 430 431 atmSigStatTable OBJECT-TYPE 432 SYNTAX SEQUENCE OF AtmSigStatEntry 433 MAX-ACCESS not-accessible 434 STATUS current 435 DESCRIPTION 436 "This table contains ATM interface signalling 437 statistics, one entry per ATM signalling 438 interface." 439 ::= { atm2MIBObjects 3 } 440 441 atmSigStatEntry OBJECT-TYPE 442 SYNTAX AtmSigStatEntry 443 MAX-ACCESS not-accessible 444 STATUS current 445 DESCRIPTION 446 "This list contains signalling statistics variables." 447 INDEX { ifIndex } 448 ::= { atmSigStatTable 1} 449 450 AtmSigStatEntry ::= SEQUENCE { 451 atmSigSSCOPConEvents Counter32, 452 atmSigSSCOPErrdPdus Counter32, 453 atmSigDetectSetupAttempts Counter32, 454 atmSigEmitSetupAttempts Counter32, 455 atmSigDetectUnavailRoutes Counter32, 456 atmSigEmitUnavailRoutes Counter32, 457 atmSigDetectUnavailResrcs Counter32, 458 atmSigEmitUnavailResrcs Counter32, 459 atmSigDetectCldPtyEvents Counter32, 460 atmSigEmitCldPtyEvents Counter32, 461 atmSigDetectMsgErrors Counter32, 462 atmSigEmitMsgErrors Counter32, 463 atmSigDetectClgPtyEvents Counter32, 464 atmSigEmitClgPtyEvents Counter32, 465 atmSigDetectTimerExpireds Counter32, 466 atmSigEmitTimerExpireds Counter32, 467 atmSigDetectRestarts Counter32, 468 atmSigEmitRestarts Counter32, 469 atmSigInEstabls Counter32, 470 atmSigOutEstabls Counter32 471 } 472 473 atmSigSSCOPConEvents OBJECT-TYPE 474 SYNTAX Counter32 475 MAX-ACCESS read-only 476 STATUS current 477 478 479 480 DESCRIPTION 481 "SSCOP Connection Events Counter. This counter counts 482 the sum of the following errors: 483 484 1) SSCOP Connection Disconnect Counter 485 486 The abnormal occurrence of this event is 487 characterized by the expiry of Timer_NO_RESPONSE. 488 (This event is communicated to the layer management 489 with MAA-ERROR code P. See ITU-T Q.2110.) 490 491 2) SSCOP Connection Initiation Failure 492 493 This condition indicates the inability to establish 494 an SSCOP connection. This event occurs whenever the 495 number of expiries of the connection control timer 496 (Timer_CC) equals or exceeds the MaxCC, or upon 497 receipt of a connection reject message BGREJ PDU. 498 (This event is communicated to layer management with 499 MAA-ERROR code O. See ITU-T Q.2110.) 500 501 3) SSCOP Connection Re-Establ/Resynch 502 503 This event occurs upon receipt of a BGN PDU or 504 RS PDU." 505 REFERENCE 506 "ITU-T Recommendation Q.2110, Broadband 507 Integrated Services Digital Network 508 (B-ISDN) - ATM Adaptation Layer - Service 509 Specific Connection Oriented Protocol (SSCOP) 510 Specification, July 1994." 511 ::= { atmSigStatEntry 1} 512 513 atmSigSSCOPErrdPdus OBJECT-TYPE 514 SYNTAX Counter32 515 MAX-ACCESS read-only 516 STATUS current 517 DESCRIPTION 518 "SSCOP Errored PDUs Counter. This counter counts the 519 sum of the following errors: 520 521 1) Invalid PDUs. 522 These are defined in SSCOP and consist of PDUs 523 with an incorrect length (MAA-ERROR code U), an 524 undefined PDU type code, or that are not 32-bit 525 aligned. 526 527 2) PDUs that result in MAA-ERROR codes and are 528 529 530 531 discarded. 532 533 See MAA-ERROR codes A-D, F-M, and Q-T defined in 534 ITU-T Q.2110." 535 REFERENCE 536 "ITU-T Recommendation Q.2110, Broadband 537 Integrated Services Digital Network 538 (B-ISDN) - ATM Adaptation Layer - Service 539 Specific Connection Oriented Protocol (SSCOP) 540 Specification, July 1994." 541 ::= { atmSigStatEntry 2 } 542 543 atmSigDetectSetupAttempts OBJECT-TYPE 544 SYNTAX Counter32 545 MAX-ACCESS read-only 546 STATUS current 547 DESCRIPTION 548 "Call Setup Attempts Counter. This counter counts 549 the number of call setup attempts (both successful 550 and unsuccessful) detected on this interface." 551 ::= { atmSigStatEntry 3 } 552 553 atmSigEmitSetupAttempts OBJECT-TYPE 554 SYNTAX Counter32 555 MAX-ACCESS read-only 556 STATUS current 557 DESCRIPTION 558 "Call Setup Attempts Counter. This counter counts 559 the number of call setup attempts (both successful 560 and unsuccessful) transmitted on this interface." 561 ::= { atmSigStatEntry 4 } 562 563 atmSigDetectUnavailRoutes OBJECT-TYPE 564 SYNTAX Counter32 565 MAX-ACCESS read-only 566 STATUS current 567 DESCRIPTION 568 "Number of Route Unavailability detected on this interface. 569 This counter is incremented when a RELEASE, RELEASE COMPLETE 570 (only when not preceded by a RELEASE message for the same 571 call), ADD PARTY REJECT, or STATUS message that 572 contains one of the following cause code values is 573 received (Note: These cause values 574 apply to both UNI3.0 and UNI3.1): 575 576 Cause Value Meaning 577 578 579 580 581 582 1 unallocated (unassigned) number 583 2 no route to specified transit network 584 3 no route to destination 585 586 NOTE: For this counter, RELEASE COMPLETE 587 messages that are a reply to a previous RELEASE 588 message and contain the same cause value, are 589 redundant (for counting purposes) and should not 590 be counted." 591 592 ::= { atmSigStatEntry 5 } 593 594 atmSigEmitUnavailRoutes OBJECT-TYPE 595 SYNTAX Counter32 596 MAX-ACCESS read-only 597 STATUS current 598 DESCRIPTION 599 "Number of Route Unavailability transmitted from this 600 interface. This counter is incremented when a RELEASE, 601 RELEASE COMPLETE (only when not preceded by a RELEASE 602 message for the same call), ADD PARTY REJECT, or 603 STATUS message that contains one of the following cause 604 code values is transmitted (Note: These cause values apply 605 to both UNI3.0 and UNI3.1): 606 607 Cause Value Meaning 608 609 1 unallocated (unassigned) number 610 2 no route to specified transit network 611 3 no route to destination 612 613 NOTE: For this counter, RELEASE COMPLETE 614 messages that are a reply to a previous RELEASE 615 message and contain the same cause value, are 616 redundant (for counting purposes) and should not 617 be counted." 618 ::= { atmSigStatEntry 6 } 619 620 atmSigDetectUnavailResrcs OBJECT-TYPE 621 SYNTAX Counter32 622 MAX-ACCESS read-only 623 STATUS current 624 DESCRIPTION 625 "Number of Resource Unavailability detected on this 626 interface. This counter is incremented when a RELEASE, 627 RELEASE COMPLETE (only when not preceded by a RELEASE 628 message for the same call), ADD PARTY REJECT, or 629 STATUS message that contains one of the following 630 631 632 633 cause code values is received (Note: These cause 634 values apply to both UNI3.0 and UNI3.1 unless 635 otherwise stated): 636 637 Cause Value Meaning 638 639 35 requested VPCI/VCI not available 640 37 user cell rate not available (UNI3.1 641 only) 642 38 network out of order 643 41 temporary failure 644 45 no VPCI/VCI available 645 47 resource unavailable, unspecified 646 49 Quality of Service unavailable 647 51 user cell rate not available (UNI3.0 648 only) 649 58 bearer capability not presently 650 available 651 63 Service or option not available, 652 unspecified 653 92 too many pending add party requests 654 655 NOTE: For this counter, RELEASE COMPLETE 656 messages that are a reply to a previous RELEASE 657 message and contain the same cause value, are 658 redundant (for counting purposes) and should not 659 be counted." 660 ::= { atmSigStatEntry 7 } 661 662 atmSigEmitUnavailResrcs OBJECT-TYPE 663 SYNTAX Counter32 664 MAX-ACCESS read-only 665 STATUS current 666 DESCRIPTION 667 "Number of Resource Unavailability transmitted from this 668 interface. This counter is incremented when a RELEASE, 669 RELEASE COMPLETE (only when not preceded by a RELEASE message 670 for the same call), ADD PARTY REJECT, or STATUS message that 671 contains one of the following cause code values is transmitted 672 (Note: These cause values apply to both UNI3.0 and UNI3.1 673 unless otherwise stated): 674 675 Cause Value Meaning 676 677 35 requested VPCI/VCI not available 678 37 user cell rate not available (UNI3.1 679 only) 680 38 network out of order 681 682 683 684 41 temporary failure 685 45 no VPCI/VCI available 686 47 resource unavailable, unspecified 687 49 Quality of Service unavailable 688 51 user cell rate not available (UNI3.0 689 only) 690 58 bearer capability not presently 691 available 692 63 Service or option not available, 693 unspecified 694 92 too many pending add party requests 695 696 NOTE: For this counter, RELEASE COMPLETE messages that are a 697 reply to a previous RELEASE message and contain the same cause 698 value, are redundant (for counting purposes) and should not be 699 counted." 700 701 ::= { atmSigStatEntry 8 } 702 703 atmSigDetectCldPtyEvents OBJECT-TYPE 704 SYNTAX Counter32 705 MAX-ACCESS read-only 706 STATUS current 707 DESCRIPTION 708 "Number of Called Party Responsible For Unsuccessful Call 709 detected on this interface. This counter is incremented when a 710 RELEASE, RELEASE COMPLETE (only when not preceded by a RELEASE 711 message for the same call), ADD PARTY REJECT, or STATUS message 712 that contains one of the following cause code values is 713 received (Note: These cause values apply to both UNI3.0 and 714 UNI3.1): 715 716 Cause Value Meaning 717 718 17 user busy 719 18 no user responding 720 21 call rejected 721 22 number changed 722 23 user rejects all calls with calling 723 line identification restriction (CLIR) 724 27 destination out of order 725 31 normal, unspecified 726 88 incompatible destination 727 728 729 NOTE: For this counter, RELEASE COMPLETE messages that are a 730 reply to a previous RELEASE message and contain the same cause 731 value, are redundant (for counting purposes) and should not be 732 733 734 735 counted. 736 737 Note: Cause Value #30 'response to STATUS ENQUIRY' was not 738 included in this memo since it did not apply to a hard 739 failure." 740 741 ::= { atmSigStatEntry 9 } 742 743 atmSigEmitCldPtyEvents OBJECT-TYPE 744 SYNTAX Counter32 745 MAX-ACCESS read-only 746 STATUS current 747 DESCRIPTION 748 749 "Number of Called Party Responsible For Unsuccessful Call 750 transmitted from this interface. This counter is incremented 751 when a RELEASE, RELEASE COMPLETE (only when not preceded by a 752 RELEASE message for the same call), ADD PARTY REJECT, or STATUS 753 message that contains one of the following cause code values is 754 transmitted (Note: These cause values apply to both UNI3.0 and 755 UNI3.1): 756 757 Cause Value Meaning 758 759 17 user busy 760 18 no user responding 761 21 call rejected 762 22 number changed 763 23 user rejects all calls with calling 764 line identification restriction (CLIR) 765 27 destination out of order 766 31 normal, unspecified 767 88 incompatible destination 768 769 NOTE: For this counter, RELEASE COMPLETE messages that are a 770 reply to a previous RELEASE message and contain the same cause 771 value, are redundant (for counting purposes) and should not be 772 counted. 773 774 Note: Cause Value #30 'response to STATUS ENQUIRY' was not 775 included in this memo since it did not apply to a hard failure." 776 777 ::= { atmSigStatEntry 10 } 778 779atmSigDetectMsgErrors OBJECT-TYPE 780 SYNTAX Counter32 781 MAX-ACCESS read-only 782 STATUS current 783 784 785 786 DESCRIPTION 787 "Number of Incorrect Messages detected on this interface. The 788 Incorrect Messages Counter reflects any sort of incorrect 789 information in a message. This includes: 790 791 - RELEASE, RELEASE COMPLETE, ADD PARTY REJECT, 792 and STATUS messages transmitted, that contain any of 793 the Cause values listed below. 794 795 - Ignored messages. These messages are dropped 796 because the message was so damaged that it could 797 not be further processed. A list of dropped 798 messages is compiled below: 799 800 1. Message with invalid protocol discriminator 801 802 2. Message with errors in the call reference I.E. 803 - Bits 5-8 of the first octet not equal to 804 '0000' 805 - Bits 1-4 of the first octet indicating a 806 length other than 3 octets 807 - RELEASE COMPLETE message received with a 808 call reference that does not relate to a 809 call active or in progress 810 - SETUP message received with call reference 811 flag incorrectly set to 1 812 - SETUP message received with a call 813 reference for a call that is already 814 active or in progress. 815 816 3. Message too short 817 818 The following cause values are monitored by this counter (Note: 819 These cause values apply to both UNI3.0 and UNI3.1 unless 820 otherwise stated): 821 822 Cause Value Meaning 823 824 10 VPCI/VCI unacceptable (UNI3.0 only) 825 36 VPCI/VCI assignment failure (UNI3.1 only) 826 81 invalid call reference value 827 82 identified channel does not exist 828 89 invalid endpoint reference 829 96 mandatory information element is missing 830 97 message type non-existent or not 831 implemented 832 99 information element non-existent or not 833 implemented 834 835 836 837 100 invalid information element contents 838 101 message not compatible with call state 839 104 incorrect message length 840 111 protocol error, unspecified 841 842 NOTE: For this counter, RELEASE COMPLETE messages that are 843 a reply to a previous RELEASE message and contain the same 844 cause value, are redundant (for counting purposes) and 845 should not be counted." 846 847 ::= { atmSigStatEntry 11 } 848 849atmSigEmitMsgErrors OBJECT-TYPE 850 SYNTAX Counter32 851 MAX-ACCESS read-only 852 STATUS current 853 DESCRIPTION 854 "Number of Incorrect Messages transmitted on this interface. 855 The Incorrect Messages Counter reflects any sort of incorrect 856 information in a message. This includes: 857 858 - RELEASE, RELEASE COMPLETE, ADD PARTY REJECT, 859 and STATUS messages transmitted or 860 received, that contain any of the Cause values 861 listed below. 862 863 - Ignored messages. These messages are dropped 864 because the message was so damaged that it could 865 not be further processed. A list of dropped 866 messages is compiled below: 867 868 1. Message with invalid protocol discriminator 869 870 2. Message with errors in the call reference I.E. 871 - Bits 5-8 of the first octet not equal to 872 '0000' 873 - Bits 1-4 of the first octet indicating a 874 length other than 3 octets 875 - RELEASE COMPLETE message received with a 876 call reference that does not relate to a 877 call active or in progress 878 - SETUP message received with call reference 879 flag incorrectly set to 1 880 - SETUP message received with a call 881 reference for a call that is already 882 active or in progress. 883 884 3. Message too short 885 886 887 888 The following cause values are monitored by this counter 889 (Note: These cause values apply to both UNI3.0 and UNI3.1 890 unless otherwise stated): 891 892 Cause Value Meaning 893 894 10 VPCI/VCI unacceptable (UNI3.0 only) 895 36 VPCI/VCI assignment failure (UNI3.1 only) 896 81 invalid call reference value 897 82 identified channel does not exist 898 89 invalid endpoint reference 899 96 mandatory information element is missing 900 97 message type non-existent or not 901 implemented 902 99 information element non-existent or not 903 implemented 904 100 invalid information element contents 905 101 message not compatible with call state 906 104 incorrect message length 907 111 protocol error, unspecified 908 909 NOTE: For this counter, RELEASE COMPLETE messages that are 910 a reply to a previous RELEASE message and contain the same 911 cause value, are redundant (for counting purposes) and 912 should not be counted." 913 914 ::= { atmSigStatEntry 12 } 915 916atmSigDetectClgPtyEvents OBJECT-TYPE 917 SYNTAX Counter32 918 MAX-ACCESS read-only 919 STATUS current 920 DESCRIPTION 921 "Number of Calling Party Events detected on this interface. 922 This counter monitors error events that occur due to the 923 originating user doing something wrong. This counter is 924 incremented when a RELEASE, RELEASE COMPLETE (only when not 925 preceded by a RELEASE message for the same call), ADD PARTY 926 REJECT, or STATUS message that contains one of the following 927 cause code values is received (Note: These cause values 928 apply to both UNI3.0 and UNI3.1): 929 930 Cause Value Meaning 931 932 28 invalid number format (address incomplete) 933 43 access information discarded 934 57 bearer capability not authorized 935 65 bearer capability not implemented 936 937 938 939 73 unsupported combination of traffic 940 parameters 941 78 AAL parameters cannot be supported (UNI3.1 942 only) 943 91 invalid transit network selection 944 93 AAL parameters cannot be supported (UNI3.0 945 only) 946 947 NOTE: For this counter, RELEASE COMPLETE messages that 948 are a reply to a previous RELEASE message and contain 949 the same cause value, are redundant (for counting purposes) 950 and should not be counted." 951 952 ::= { atmSigStatEntry 13 } 953 954atmSigEmitClgPtyEvents OBJECT-TYPE 955 SYNTAX Counter32 956 MAX-ACCESS read-only 957 STATUS current 958 DESCRIPTION 959 "Number of Calling Party Events transmitted from this interface. 960 This counter monitors error events that occur due to the 961 originating user doing something wrong. This counter is 962 incremented when a RELEASE, RELEASE COMPLETE (only when not 963 preceded by a RELEASE message for the same call), ADD PARTY 964 REJECT, or STATUS message that contains one of the following 965 cause code values is transmitted (Note: These cause values 966 apply to both UNI3.0 and UNI3.1): 967 968 Cause Value Meaning 969 970 28 invalid number format (address incomplete) 971 43 access information discarded 972 57 bearer capability not authorized 973 65 bearer capability not implemented 974 73 unsupported combination of traffic 975 parameters 976 78 AAL parameters cannot be supported (UNI3.1 977 only) 978 91 invalid transit network selection 979 93 AAL parameters cannot be supported (UNI3.0 980 only) 981 982 NOTE: For this counter, RELEASE COMPLETE messages that are 983 a reply to a previous RELEASE message and contain the same 984 cause value, are redundant (for counting purposes) and 985 should not be counted." 986 987 988 989 990 ::= { atmSigStatEntry 14 } 991 992atmSigDetectTimerExpireds OBJECT-TYPE 993 SYNTAX Counter32 994 MAX-ACCESS read-only 995 STATUS current 996 DESCRIPTION 997 "Number of Timer Expiries detected on this interface. The Timer 998 Expiries Counter provides a count of network timer expiries, and 999 to some extent, host or switch timer expiries. The conditions 1000 for incrementing this counter are: 1001 1002 - Expiry of any network timer 1003 1004 - Receipt of a RELEASE or RELEASE COMPLETE 1005 message with Cause #102, 'recovery on 1006 timer expiry'. 1007 1008 NOTE: For this counter, RELEASE COMPLETE messages that are 1009 a reply to a previous RELEASE message and contain the same 1010 cause value, are redundant (for counting purposes) and 1011 should not be counted." 1012 1013 ::= { atmSigStatEntry 15 } 1014 1015atmSigEmitTimerExpireds OBJECT-TYPE 1016 SYNTAX Counter32 1017 MAX-ACCESS read-only 1018 STATUS current 1019 DESCRIPTION 1020 "Number of Timer Expiries transmitted from this interface. 1021 The Timer Expiries Counter provides a count of network timer 1022 expiries, and to some extent, host or switch timer expiries. 1023 The conditions for incrementing this counter are: 1024 1025 - Expiry of any network timer 1026 1027 - Receipt of a RELEASE or RELEASE COMPLETE 1028 message with Cause #102, 'recovery on 1029 timer expiry'. 1030 1031 NOTE: For this counter, RELEASE COMPLETE messages that are a 1032 reply to a previous RELEASE message and contain the same cause 1033 value, are redundant (for counting purposes) and should not be 1034 counted." 1035 1036 ::= { atmSigStatEntry 16 } 1037 1038 1039 1040 1041atmSigDetectRestarts OBJECT-TYPE 1042 SYNTAX Counter32 1043 MAX-ACCESS read-only 1044 STATUS current 1045 DESCRIPTION 1046 "Number of Restart Activity errors detected on this interface. 1047 The Restart Activity Counter provides a count of host, switch, 1048 or network restart activity. This counter is incremented when 1049 receiving a RESTART message." 1050 1051 ::= { atmSigStatEntry 17 } 1052 1053atmSigEmitRestarts OBJECT-TYPE 1054 SYNTAX Counter32 1055 MAX-ACCESS read-only 1056 STATUS current 1057 DESCRIPTION 1058 "Number of Restart Activity errors transmitted from this 1059 interface. The Restart Activity Counter provides a count of 1060 host, switch, or network restart activity. This counter is 1061 incremented when transmitting a RESTART message." 1062 1063 ::= { atmSigStatEntry 18 } 1064 1065atmSigInEstabls OBJECT-TYPE 1066 SYNTAX Counter32 1067 MAX-ACCESS read-only 1068 STATUS current 1069 DESCRIPTION 1070 "Number of SVCs established at this signalling entity for 1071 incoming connections." 1072 ::= { atmSigStatEntry 19 } 1073 1074atmSigOutEstabls OBJECT-TYPE 1075 SYNTAX Counter32 1076 MAX-ACCESS read-only 1077 STATUS current 1078 DESCRIPTION 1079 "Number of SVCs established at this signalling entity for 1080 outgoing connections." 1081 ::= { atmSigStatEntry 20 } 1082 1083 -- 4. ATM Interface Signalling Support Table 1084 -- 1085 -- This table provides information to support 1086 -- the signalling process which is used to establish 1087 -- ATM Switched Virtual Connections (SVCs). 1088 1089 1090 1091 1092atmSigSupportTable OBJECT-TYPE 1093 SYNTAX SEQUENCE OF AtmSigSupportEntry 1094 MAX-ACCESS not-accessible 1095 STATUS current 1096 DESCRIPTION 1097 "This table contains ATM local interface configuration 1098 parameters, one entry per ATM signalling interface." 1099 ::= { atm2MIBObjects 4 } 1100 1101atmSigSupportEntry OBJECT-TYPE 1102 SYNTAX AtmSigSupportEntry 1103 MAX-ACCESS not-accessible 1104 STATUS current 1105 DESCRIPTION 1106 "This list contains signalling configuration parameters 1107 and state variables." 1108 INDEX { ifIndex } 1109 ::= { atmSigSupportTable 1} 1110 1111AtmSigSupportEntry ::= SEQUENCE { 1112 atmSigSupportClgPtyNumDel INTEGER, 1113 atmSigSupportClgPtySubAddr INTEGER, 1114 atmSigSupportCldPtySubAddr INTEGER, 1115 atmSigSupportHiLyrInfo INTEGER, 1116 atmSigSupportLoLyrInfo INTEGER, 1117 atmSigSupportBlliRepeatInd INTEGER, 1118 atmSigSupportAALInfo INTEGER, 1119 atmSigSupportPrefCarrier OCTET STRING 1120} 1121 1122atmSigSupportClgPtyNumDel OBJECT-TYPE 1123 SYNTAX INTEGER { enabled(1), disabled(2) } 1124 MAX-ACCESS read-write 1125 STATUS current 1126 DESCRIPTION 1127 "This object indicates whether the Calling Party Number 1128 Information Element is transferred to the called party 1129 address. The value of this object can be: 1130 1131 - enabled(1) This Information Element is transferred 1132 to the called party 1133 1134 - disabled(2) This Information Element is NOT 1135 transferred to the called party." 1136 1137 ::= { atmSigSupportEntry 1 } 1138 1139atmSigSupportClgPtySubAddr OBJECT-TYPE 1140 1141 1142 1143 SYNTAX INTEGER { enabled(1), disabled(2) } 1144 MAX-ACCESS read-write 1145 STATUS current 1146 DESCRIPTION 1147 "This object indicates whether to accept and transfer the Calling 1148 Party Subaddress Information Element from the calling party to 1149 the called party. Calling party subaddress information shall 1150 only be transferred to the called party if calling party number 1151 delivery is enabled (i.e., atmSigSupportClgPtyNumDel = 1152 'enabled(1)'. The value of this object can be: 1153 1154 - enabled(1) This Information Element is transferred 1155 to the called party 1156 1157 - disabled(2) This Information Element is NOT 1158 transferred to the called party." 1159 1160 ::= { atmSigSupportEntry 2 } 1161 1162atmSigSupportCldPtySubAddr OBJECT-TYPE 1163 SYNTAX INTEGER { enabled(1), disabled(2) } 1164 MAX-ACCESS read-write 1165 STATUS current 1166 DESCRIPTION 1167 "This object indicates whether to accept, transfer, and deliver 1168 the Called Party Subaddress Information Element from the calling 1169 party to the called party. The value of this object can be: 1170 1171 - enabled(1) This Information Element is transferred 1172 to the called party 1173 1174 - disabled(2) This Information Element is NOT 1175 transferred to the called party." 1176 1177 ::= { atmSigSupportEntry 3 } 1178 1179atmSigSupportHiLyrInfo OBJECT-TYPE 1180 SYNTAX INTEGER { enabled(1), disabled(2) } 1181 MAX-ACCESS read-write 1182 STATUS current 1183 DESCRIPTION 1184 "This object indicates whether to accept, transfer, and deliver 1185 the Broadband High Layer Information Element from the calling 1186 party to the called party. The value of this object can be: 1187 1188 - enabled(1) This Information Element is transferred 1189 to the called party 1190 1191 1192 1193 1194 - disabled(2) This Information Element is NOT 1195 transferred to the called party." 1196 1197 ::= { atmSigSupportEntry 4 } 1198 1199atmSigSupportLoLyrInfo OBJECT-TYPE 1200 SYNTAX INTEGER { enabled(1), disabled(2) } 1201 MAX-ACCESS read-write 1202 STATUS current 1203 DESCRIPTION 1204 "This object indicates whether to accept, transfer, and deliver 1205 the Broadband Low Layer Information Element from the calling 1206 party to the called party. The value of this object can be: 1207 1208 - enabled(1) This Information Element is transferred 1209 to the called party 1210 1211 - disabled(2) This Information Element is NOT 1212 transferred to the called party." 1213 1214 ::= { atmSigSupportEntry 5 } 1215 1216atmSigSupportBlliRepeatInd OBJECT-TYPE 1217 SYNTAX INTEGER { enabled(1), disabled(2) } 1218 MAX-ACCESS read-write 1219 STATUS current 1220 DESCRIPTION 1221 "This object indicates whether to accept, transfer, and deliver 1222 the Broadband Repeat Indicator with two or three instances of 1223 the Broadband Low Layer Information Element for low layer 1224 information selection from the calling party to the called 1225 party. This object's value should always be disabled(2) if 1226 the value of atmSigSupportLolyrInfo is disabled(2). 1227 1228 The value of this object can be: 1229 1230 - enabled(1) This Information Element is transferred 1231 to the called party 1232 1233 - disabled(2) This Information Element is NOT 1234 transferred to the called party." 1235 ::= { atmSigSupportEntry 6 } 1236 1237atmSigSupportAALInfo OBJECT-TYPE 1238 SYNTAX INTEGER { enabled(1), disabled(2) } 1239 MAX-ACCESS read-write 1240 STATUS current 1241 DESCRIPTION 1242 1243 1244 1245 "This object indicates whether to accept, transfer, and deliver 1246 the ATM Adaptation Layer Parameters Information Element from the 1247 calling party to the called party. The value of this object can 1248 be: 1249 1250 - enabled(1) This Information Element is transferred 1251 to the called party 1252 1253 - disabled(2) This Information Element is NOT 1254 transferred to the called party." 1255 1256 ::= { atmSigSupportEntry 7 } 1257 1258atmSigSupportPrefCarrier OBJECT-TYPE 1259 SYNTAX OCTET STRING (SIZE(0|4)) 1260 MAX-ACCESS read-write 1261 STATUS current 1262 DESCRIPTION 1263 "This parameter identifies the carrier to which intercarrier 1264 calls originated from this interface are routed when transit 1265 network selection information is not provided by the calling 1266 party. If a Carrier Identification Code (CIC) is used the 1267 parameter shall contain the CIC. For three-digit CICs, the first 1268 octet shall be '0' and the CIC is contained in the three 1269 following octets. If the preferred carrier feature is not 1270 supported the value is a zero-length string." 1271 1272 ::= { atmSigSupportEntry 8 } 1273 1274 -- 5. ATM Signalling Descriptor Parameter Table 1275 1276 atmSigDescrParamTable OBJECT-TYPE 1277 SYNTAX SEQUENCE OF AtmSigDescrParamEntry 1278 MAX-ACCESS not-accessible 1279 STATUS current 1280 DESCRIPTION 1281 "A table contains signalling capabilities of VCLs except the 1282 Traffic Descriptor. Traffic descriptors are described in 1283 the atmTrafficDescrParamTable." 1284 1285 REFERENCE 1286 "ATM User-Network Interface Specification, Version 3.1 (UNI 1287 3.1), September 1994, Section 5.4.5 Variable Length 1288 Information Elements." 1289 1290 ::= { atm2MIBObjects 5 } 1291 1292 atmSigDescrParamEntry OBJECT-TYPE 1293 1294 1295 1296 SYNTAX AtmSigDescrParamEntry 1297 MAX-ACCESS not-accessible 1298 STATUS current 1299 DESCRIPTION 1300 "Each entry in this table represents a 1301 set of signalling capabilities that can 1302 be applied to a VCL. There is no requirement 1303 for unique entries, except that the index must 1304 be unique." 1305 INDEX { atmSigDescrParamIndex } 1306 ::= { atmSigDescrParamTable 1 } 1307 1308 AtmSigDescrParamEntry ::= 1309 SEQUENCE { 1310 atmSigDescrParamIndex 1311 AtmSigDescrParamIndex, 1312 atmSigDescrParamAalType INTEGER, 1313 atmSigDescrParamAalSscsType INTEGER, 1314 atmSigDescrParamBhliType INTEGER, 1315 1316 1317 atmSigDescrParamBhliInfo OCTET STRING, 1318 atmSigDescrParamBbcConnConf INTEGER, 1319 atmSigDescrParamBlliLayer2 INTEGER, 1320 atmSigDescrParamBlliLayer3 INTEGER, 1321 atmSigDescrParamBlliPktSize INTEGER, 1322 atmSigDescrParamBlliSnapId INTEGER, 1323 atmSigDescrParamBlliOuiPid OCTET STRING, 1324 atmSigDescrParamRowStatus RowStatus 1325 } 1326 1327 atmSigDescrParamIndex OBJECT-TYPE 1328 SYNTAX AtmSigDescrParamIndex 1329 MAX-ACCESS not-accessible 1330 STATUS current 1331 DESCRIPTION 1332 "The value of this object is used by the 1333 atmVclGenSigDescrIndex object in the atmVclGenTable to 1334 identify a row in this table." 1335 1336 ::= { atmSigDescrParamEntry 1 } 1337 1338 atmSigDescrParamAalType OBJECT-TYPE 1339 SYNTAX INTEGER { 1340 other(1), -- not defined 1341 aal1(2), -- AAL type 1 1342 aal34(3), -- AAL type 3/4 1343 aal5(4), -- AAL type 5 1344 1345 1346 1347 userDefined(5), -- User-Defined AAL 1348 aal2(6) -- AAL type 2 1349 } 1350 MAX-ACCESS read-create 1351 STATUS current 1352 DESCRIPTION 1353 "The AAL type. The value of this object is set to other(1) 1354 when not defined." 1355 1356 DEFVAL { other } 1357 ::= { atmSigDescrParamEntry 2 } 1358 1359 atmSigDescrParamAalSscsType OBJECT-TYPE 1360 SYNTAX INTEGER { 1361 other(1), -- other, or not used 1362 assured(2), -- Data SSCS based on SSCOP 1363 -- assured operation 1364 nonassured(3), -- Data SSCS based on SSCOP 1365 -- non-assured operation 1366 frameRelay(4), -- frame relay SSCS 1367 null(5) -- null 1368 1369 } 1370 MAX-ACCESS read-create 1371 STATUS current 1372 DESCRIPTION 1373 "The SSCS type used by this entry." 1374 1375 DEFVAL { other } 1376 ::= { atmSigDescrParamEntry 3 } 1377 1378 atmSigDescrParamBhliType OBJECT-TYPE 1379 SYNTAX INTEGER { 1380 other(1), -- not defined 1381 iso(2), -- ISO 1382 user(3), -- User specific 1383 hiProfile(4), -- Higher layer profile 1384 -- this enum applicable to 1385 -- UNI 3.0 only 1386 vendorSpecific(5) -- Vender specific 1387 -- application identifier 1388 } 1389 MAX-ACCESS read-create 1390 STATUS current 1391 DESCRIPTION 1392 "The Broadband high layer type." 1393 1394 DEFVAL { other } 1395 1396 1397 1398 ::= { atmSigDescrParamEntry 4 } 1399 1400 atmSigDescrParamBhliInfo OBJECT-TYPE 1401 SYNTAX OCTET STRING (SIZE(0..8)) 1402 MAX-ACCESS read-create 1403 STATUS current 1404 DESCRIPTION 1405 "The Broadband high layer information. When 1406 atmSigDescrParamBhliType is set to iso(2), the value of this 1407 object is a zero length string. When 1408 atmSigDescrParamBhliType is set to user(3), the value of 1409 this object is an octet string with length ranging from 0 to 1410 8. When atmSigDescrParamBhliType is set to hiProfile(4), 1411 the value of this object is a length of 4 octet string 1412 containing user to user profile identifier. When 1413 atmSigDescrParamBhliType is set to vendorSpecific(5), the 1414 value of this object is a length of 7 octet string, where 1415 the most significant 3 octets consist of a globally- 1416 administered OUI, and the least significant 4 octets are the 1417 vender administered application OUI." 1418 1419 DEFVAL { ''H } 1420 1421 ::= { atmSigDescrParamEntry 5 } 1422 1423 atmSigDescrParamBbcConnConf OBJECT-TYPE 1424 SYNTAX INTEGER { 1425 ptp(1), -- point-to-point 1426 ptmp(2) -- point-to-multipoint 1427 } 1428 MAX-ACCESS read-create 1429 STATUS current 1430 DESCRIPTION 1431 "The Broadband bearer capability user plane connection 1432 configuration parameter." 1433 DEFVAL { ptp } 1434 ::= { atmSigDescrParamEntry 6 } 1435 1436 atmSigDescrParamBlliLayer2 OBJECT-TYPE 1437 SYNTAX INTEGER { 1438 other(1), -- not specified 1439 iso1745(2), -- Basic mode ISO 1745 1440 q921(3), -- CCITT Recommendation Q.921 1441 x25linklayer(4), -- CCITT Recommendation X.25 1442 -- Link Layer 1443 x25multilink(5), -- CCITT Recommendation X.25 1444 -- Multilink 1445 lapb(6), -- Extended LAPB; for half 1446 1447 1448 1449 -- duplex operation 1450 hdlcArm(7), -- HDLC ARM (ISO 4335) 1451 hdlcNrm(8), -- HDLC NRM (ISO 4335) 1452 hdlcAbm(9), -- HDLC ABM (ISO 4335) 1453 iso88022(10), -- LAN logical link control 1454 -- (ISO 8802/2) 1455 x75slp(11), -- CCITT Recommendation X.75, 1456 -- single link 1457 -- procedure (SLP) 1458 q922(12), -- CCITT Recommendation Q.922 1459 userDef(13), -- User specified 1460 iso7776(14) -- ISO 7776 DTE-DTE operation 1461 } 1462 MAX-ACCESS read-create 1463 STATUS current 1464 DESCRIPTION 1465 "The Broadband low layer information, protocol type of layer 1466 2. The value of this object is other(1) if layer 2 protocol 1467 is not used." 1468 1469 DEFVAL { other } 1470 ::= { atmSigDescrParamEntry 7 } 1471 1472 atmSigDescrParamBlliLayer3 OBJECT-TYPE 1473 SYNTAX INTEGER { 1474 other(1), -- not specified 1475 x25pkt(2), -- CCITT Recommendation X.25 1476 -- packet layer 1477 isoiec8208(3), -- ISO/IEC 8208 (X.25 packet 1478 -- level protocol for data 1479 -- terminal equipment) 1480 x223iso8878(4), -- X.223/ISO 8878 1481 isoiec8473(5), -- ISO/IEC 8473 OSI 1482 -- connectionless 1483 -- mode protocol 1484 t70(6), -- CCITT Recommendation T.70 1485 -- minimum 1486 -- network layer 1487 tr9577(7), -- ISO/IEC TR 9577 Protocol 1488 -- Identification in the 1489 -- network layer 1490 userDef(8) -- user specified 1491 1492 } 1493 MAX-ACCESS read-create 1494 STATUS current 1495 DESCRIPTION 1496 "The Broadband low layer information, protocol type of layer 1497 1498 1499 1500 3. The value of this object is other(1) if layer 3 protocol 1501 is not used." 1502 1503 DEFVAL { other } 1504 ::= { atmSigDescrParamEntry 8 } 1505 1506 atmSigDescrParamBlliPktSize OBJECT-TYPE 1507 SYNTAX INTEGER { 1508 other(1), -- not used 1509 s16(2), -- 16 octets 1510 s32(3), -- 32 octets 1511 s64(4), -- 64 octets 1512 s128(5), -- 128 octets 1513 s256(6), -- 256 octets 1514 s512(7), -- 512 octets 1515 s1024(8), -- 1028 octets 1516 s2048(9), -- 2048 octets 1517 s4096(10) -- 4096 octets 1518 } 1519 MAX-ACCESS read-create 1520 STATUS current 1521 DESCRIPTION 1522 "The default packet size defined in B-LLI." 1523 1524 DEFVAL { other } 1525 ::= { atmSigDescrParamEntry 9 } 1526 1527 atmSigDescrParamBlliSnapId OBJECT-TYPE 1528 SYNTAX INTEGER { 1529 other(1), -- not used 1530 true(2), -- SNAP ID is 1 1531 false(3) -- SNAP ID is 0 1532 } 1533 MAX-ACCESS read-create 1534 STATUS current 1535 DESCRIPTION 1536 "The SNAP ID used for Broadband low layer protocol layer 3. 1537 The value of this object is other(1) if 1538 atmSigDescrParamBlliLayer3 is set to other(1)." 1539 1540 DEFVAL { other } 1541 ::= { atmSigDescrParamEntry 10 } 1542 1543 atmSigDescrParamBlliOuiPid OBJECT-TYPE 1544 SYNTAX OCTET STRING (SIZE(0|5)) 1545 MAX-ACCESS read-create 1546 STATUS current 1547 DESCRIPTION 1548 1549 1550 1551 "The OUI/PID encoding for Broadband low layer protocol layer 1552 3. The value of this object is a zero length string if 1553 atmSigDescrParamBlliLayer3 is set to other(1). When used, 1554 it is always 5 octets with the most significant octet as the 1555 OUI Octet 1 and the least significant octet as the PID Octet 1556 2." 1557 1558 DEFVAL { ''H } 1559 ::= { atmSigDescrParamEntry 11 } 1560 1561 atmSigDescrParamRowStatus OBJECT-TYPE 1562 SYNTAX RowStatus 1563 MAX-ACCESS read-create 1564 STATUS current 1565 DESCRIPTION 1566 "This object is used to create and delete rows in the 1567 atmSigDescrParamTable." 1568 1569 ::= { atmSigDescrParamEntry 12 } 1570 1571 -- 6. ATM Interface Registered Address Table -- 1572 1573atmIfRegisteredAddrTable OBJECT-TYPE 1574 SYNTAX SEQUENCE OF AtmIfRegisteredAddrEntry 1575 MAX-ACCESS not-accessible 1576 STATUS current 1577 DESCRIPTION 1578 "This table contains a list of ATM addresses that can be used for 1579 calls to and from a given interface by a switch or service. The 1580 ATM addresses are either registered by the endsystem via ILMI or 1581 statically configured. This table does not expose PNNI 1582 reachability information. ILMI registered addresses cannot be 1583 deleted using this table. This table only applies to switches 1584 and network services." 1585 ::= { atm2MIBObjects 6 } 1586 1587atmIfRegisteredAddrEntry OBJECT-TYPE 1588 SYNTAX AtmIfRegisteredAddrEntry 1589 MAX-ACCESS not-accessible 1590 STATUS current 1591 DESCRIPTION 1592 "An entry in the ATM Interface Registered Address table." 1593 1594 INDEX { ifIndex, atmIfRegAddrAddress } 1595 ::= { atmIfRegisteredAddrTable 1} 1596 1597AtmIfRegisteredAddrEntry ::= SEQUENCE { 1598 atmIfRegAddrAddress AtmAddr, 1599 1600 1601 1602 atmIfRegAddrAddressSource INTEGER, 1603 atmIfRegAddrOrgScope INTEGER, 1604 atmIfRegAddrRowStatus RowStatus 1605 } 1606 1607atmIfRegAddrAddress OBJECT-TYPE 1608 SYNTAX AtmAddr 1609 MAX-ACCESS not-accessible 1610 STATUS current 1611 DESCRIPTION 1612 "An address registered for a given switch or service interface." 1613 1614 ::= { atmIfRegisteredAddrEntry 1} 1615 1616atmIfRegAddrAddressSource OBJECT-TYPE 1617 SYNTAX INTEGER { 1618 other(1), 1619 static(2), 1620 dynamic(3) 1621 } 1622 MAX-ACCESS read-only 1623 STATUS current 1624 DESCRIPTION 1625 "The type of address source for a given ATM Address. The value 1626 dynamic(3) is indicated when ILMI is used." 1627 ::= { atmIfRegisteredAddrEntry 2} 1628 1629atmIfRegAddrOrgScope OBJECT-TYPE 1630 SYNTAX INTEGER { 1631 localNetwork(1), 1632 localNetworkPlusOne(2), 1633 localNetworkPlusTwo(3), 1634 siteMinusOne(4), 1635 intraSite(5), 1636 sitePlusOne(6), 1637 organizationMinusOne(7), 1638 intraOrganization(8), 1639 organizationPlusOne(9), 1640 communityMinusOne(10), 1641 intraCommunity(11), 1642 communityPlusOne(12), 1643 regional(13), 1644 interRegional(14), 1645 global(15) 1646 } 1647 MAX-ACCESS read-create 1648 STATUS current 1649 DESCRIPTION 1650 1651 1652 1653 "This object indicates the organizational scope for 1654 the referenced address. The information of the 1655 referenced address shall not be distributed outside 1656 the indicated scope. Refer to Annex 5.3 of ATM 1657 Forum UNI Signalling 4.0 for guidelines regarding 1658 the use of organizational scopes. 1659 1660 This value cannot be configured for ILMI-registered 1661 addresses. 1662 1663 The default values for organizational scope are 1664 localNetwork(1) for ATM group addresses, and 1665 global(15) for individual addresses." 1666 ::= { atmIfRegisteredAddrEntry 3} 1667 1668atmIfRegAddrRowStatus OBJECT-TYPE 1669 SYNTAX RowStatus 1670 MAX-ACCESS read-create 1671 STATUS current 1672 DESCRIPTION 1673 "This object is used to create and delete rows in the 1674 atmIfRegisteredAddrTable. Rows created dynamically (e.g., ILMI- 1675 registered addresses) cannot be deleted using this object." 1676 1677 ::= { atmIfRegisteredAddrEntry 4} 1678 1679 -- 7. ATM VPI/VCI to Address Mapping Table 1680 1681 atmVclAddrTable OBJECT-TYPE 1682 SYNTAX SEQUENCE OF AtmVclAddrEntry 1683 MAX-ACCESS not-accessible 1684 STATUS current 1685 DESCRIPTION 1686 "This table provides a mapping between the atmVclTable and 1687 the ATM called party/calling party address. This table can 1688 be used to retrieve the calling party and called party ATM 1689 address pair for a given VCL. Note that there can be more 1690 than one pair of calling party and called party ATM 1691 addresses for a VCL in a point to multi-point call." 1692 ::= { atm2MIBObjects 7 } 1693 1694 atmVclAddrEntry OBJECT-TYPE 1695 SYNTAX AtmVclAddrEntry 1696 MAX-ACCESS not-accessible 1697 STATUS current 1698 DESCRIPTION 1699 "Each entry in this table represents a binding between a VCL 1700 and an ATM address associated with this call. This ATM 1701 1702 1703 1704 address can be either the called party address or the 1705 calling party address. There can be more than one pair of 1706 calling/called party ATM addresses associated with the VCL 1707 entry for point to multi-point calls. Objects 1708 atmVclAddrType, and atmVclAddrRowStatus are 1709 required during row creation." 1710 INDEX { ifIndex, atmVclVpi, atmVclVci, 1711 atmVclAddrAddr } 1712 ::= { atmVclAddrTable 1 } 1713 1714 AtmVclAddrEntry ::= 1715 SEQUENCE { 1716 atmVclAddrAddr AtmAddr, 1717 atmVclAddrType INTEGER, 1718 atmVclAddrRowStatus RowStatus 1719 } 1720 1721 atmVclAddrAddr OBJECT-TYPE 1722 SYNTAX AtmAddr 1723 MAX-ACCESS not-accessible 1724 STATUS current 1725 DESCRIPTION 1726 "An ATM address on one end of the VCL. For SVCs, the agent 1727 supplies the value of this object at creation time. For PVC 1728 VCL, the manager can supply the value of this object during 1729 or after the PVC VCL creation." 1730 ::= { atmVclAddrEntry 1 } 1731 1732 atmVclAddrType OBJECT-TYPE 1733 SYNTAX INTEGER { 1734 callingParty(1), 1735 calledParty(2) 1736 } 1737 MAX-ACCESS read-create 1738 STATUS current 1739 DESCRIPTION 1740 "The type of ATM Address represented by the object 1741 atmVclAddrAddr. Choices are either the calling party ATM 1742 address or the called party ATM address." 1743 ::= { atmVclAddrEntry 2 } 1744 1745 atmVclAddrRowStatus OBJECT-TYPE 1746 SYNTAX RowStatus 1747 MAX-ACCESS read-create 1748 STATUS current 1749 DESCRIPTION 1750 "This object is used to create or destroy an 1751 entry from this table. Note that the manager entity 1752 1753 1754 1755 can only destroy the PVC VCLs." 1756 ::= { atmVclAddrEntry 3 } 1757 1758 -- 8. ATM Address to VPI/VCI Mapping Table 1759 -- 1760 -- This table provides an alternative way to access 1761 -- a row in the atmVclAddrTable by using 1762 -- an ATM address as an index, instead of 1763 -- the ifIndex 1764 1765 atmAddrVclTable OBJECT-TYPE 1766 SYNTAX SEQUENCE OF AtmAddrVclEntry 1767 MAX-ACCESS not-accessible 1768 STATUS current 1769 DESCRIPTION 1770 "This table provides an alternative way to retrieve the 1771 atmVclTable. This table can be used to retrieve the 1772 indexing to the atmVclTable by an ATM address." 1773 1774 ::= { atm2MIBObjects 8 } 1775 1776 atmAddrVclEntry OBJECT-TYPE 1777 SYNTAX AtmAddrVclEntry 1778 MAX-ACCESS not-accessible 1779 STATUS current 1780 DESCRIPTION 1781 "Each entry in this table represents an entry in the 1782 atmVclTable of the ATM-MIB by its ATM address. The ATM 1783 address is either the calling or called party ATM address 1784 of the call. Entries in this table are read only. 1785 They show up when entries are created in the 1786 atmVclAddrTable." 1787 REFERENCE 1788 "Tesink, K., Editor, Definitions of Managed Objects 1789 for ATM Management, RFC 2515, Bell Communications 1790 Research, February, 1999." 1791 INDEX { atmVclAddrAddr, atmAddrVclAtmIfIndex, 1792 atmAddrVclVpi, atmAddrVclVci } 1793 ::= { atmAddrVclTable 1 } 1794 1795 AtmAddrVclEntry ::= 1796 SEQUENCE { 1797 atmAddrVclAtmIfIndex InterfaceIndex, 1798 atmAddrVclVpi AtmVpIdentifier, 1799 atmAddrVclVci AtmVcIdentifier, 1800 atmAddrVclAddrType INTEGER 1801 } 1802 1803 1804 1805 1806 atmAddrVclAtmIfIndex OBJECT-TYPE 1807 SYNTAX InterfaceIndex 1808 MAX-ACCESS not-accessible 1809 STATUS current 1810 DESCRIPTION 1811 "The interface index of the ATM interface to which this 1812 VCL pertains. This object combined with the 1813 atmAddrVclVpi and atmAddrVclVci objects serves as an 1814 index to the atmVclTable." 1815 ::= { atmAddrVclEntry 1 } 1816 1817 atmAddrVclVpi OBJECT-TYPE 1818 SYNTAX AtmVpIdentifier 1819 MAX-ACCESS not-accessible 1820 STATUS current 1821 DESCRIPTION 1822 "The VPI value of the VCL. This object combined with the 1823 atmAddrVclAtmIfIndex and atmAddrVclVci objects serves as 1824 an index to the atmVclTable." 1825 ::= { atmAddrVclEntry 2 } 1826 1827 atmAddrVclVci OBJECT-TYPE 1828 SYNTAX AtmVcIdentifier 1829 MAX-ACCESS not-accessible 1830 STATUS current 1831 DESCRIPTION 1832 "The VCI value of the VCL. This object combined with the 1833 atmAddrVclAtmIfIndex and atmAddrVclVpi objects serves as 1834 an index to the atmVclTable." 1835 ::= { atmAddrVclEntry 3 } 1836 1837 atmAddrVclAddrType OBJECT-TYPE 1838 SYNTAX INTEGER { 1839 callingParty(1), 1840 calledParty(2) } 1841 MAX-ACCESS read-only 1842 STATUS current 1843 DESCRIPTION 1844 "The type of ATM Address represented by the object 1845 atmVclAddrAddr. Choices are either calling party address 1846 or called party address." 1847 ::= { atmAddrVclEntry 4 } 1848 1849 -- 9. ATM VPL Statistics Table 1850 1851 atmVplStatTable OBJECT-TYPE 1852 SYNTAX SEQUENCE OF AtmVplStatEntry 1853 MAX-ACCESS not-accessible 1854 1855 1856 1857 STATUS current 1858 DESCRIPTION 1859 "This table contains all statistics counters per VPL. It is 1860 used to monitor the usage of the VPL in terms of incoming 1861 cells and outgoing cells." 1862 ::= { atm2MIBObjects 9 } 1863 1864 atmVplStatEntry OBJECT-TYPE 1865 SYNTAX AtmVplStatEntry 1866 MAX-ACCESS not-accessible 1867 STATUS current 1868 DESCRIPTION 1869 "Each entry in this table represents a VPL." 1870 INDEX { ifIndex, atmVplVpi } 1871 ::= { atmVplStatTable 1 } 1872 1873 AtmVplStatEntry ::= 1874 SEQUENCE { 1875 atmVplStatTotalCellIns Counter32, 1876 atmVplStatClp0CellIns Counter32, 1877 atmVplStatTotalDiscards Counter32, 1878 atmVplStatClp0Discards Counter32, 1879 atmVplStatTotalCellOuts Counter32, 1880 atmVplStatClp0CellOuts Counter32, 1881 atmVplStatClp0Tagged Counter32 1882 } 1883 1884 atmVplStatTotalCellIns OBJECT-TYPE 1885 SYNTAX Counter32 1886 MAX-ACCESS read-only 1887 STATUS current 1888 DESCRIPTION 1889 "The total number of valid ATM cells received by this VPL 1890 including both CLP=0 and CLP=1 cells. The cells are 1891 counted prior to the application of the traffic policing." 1892 ::= { atmVplStatEntry 1 } 1893 1894 atmVplStatClp0CellIns OBJECT-TYPE 1895 SYNTAX Counter32 1896 MAX-ACCESS read-only 1897 STATUS current 1898 DESCRIPTION 1899 "The number of valid ATM cells received by this VPL with 1900 CLP=0. The cells are counted prior to the application of 1901 the traffic policing." 1902 ::= { atmVplStatEntry 2 } 1903 1904 atmVplStatTotalDiscards OBJECT-TYPE 1905 1906 1907 1908 SYNTAX Counter32 1909 MAX-ACCESS read-only 1910 STATUS current 1911 DESCRIPTION 1912 "The total number of valid ATM cells discarded by the 1913 traffic policing entity. This includes cells originally 1914 received with CLP=0 and CLP=1." 1915 ::= { atmVplStatEntry 3 } 1916 1917 atmVplStatClp0Discards OBJECT-TYPE 1918 SYNTAX Counter32 1919 MAX-ACCESS read-only 1920 STATUS current 1921 DESCRIPTION 1922 "The total number of valid ATM cells received with CLP=0 and 1923 discarded by the traffic policing entity." 1924 ::= { atmVplStatEntry 4 } 1925 1926 atmVplStatTotalCellOuts OBJECT-TYPE 1927 SYNTAX Counter32 1928 MAX-ACCESS read-only 1929 STATUS current 1930 DESCRIPTION 1931 "The total number of valid ATM cells transmitted by this 1932 VPL. This includes both CLP=0 and CLP=1 cells." 1933 ::= { atmVplStatEntry 5 } 1934 1935 atmVplStatClp0CellOuts OBJECT-TYPE 1936 SYNTAX Counter32 1937 MAX-ACCESS read-only 1938 STATUS current 1939 DESCRIPTION 1940 "The total number of valid ATM cells transmitted with CLP=0 1941 by this VPL." 1942 ::= { atmVplStatEntry 6 } 1943 1944 atmVplStatClp0Tagged OBJECT-TYPE 1945 SYNTAX Counter32 1946 MAX-ACCESS read-only 1947 STATUS current 1948 DESCRIPTION 1949 "The total number of valid ATM cells tagged by the traffic 1950 policing entity from CLP=0 to CLP=1." 1951 ::= { atmVplStatEntry 7 } 1952 1953 -- 10. ATM Logical Port Configuration Table 1954 1955 atmVplLogicalPortTable OBJECT-TYPE 1956 1957 1958 1959 SYNTAX SEQUENCE OF AtmVplLogicalPortEntry 1960 MAX-ACCESS not-accessible 1961 STATUS current 1962 DESCRIPTION 1963 "Indicates whether the VPL is an ATM Logical Port interface 1964 (ifType=80)." 1965 ::= { atm2MIBObjects 10 } 1966 1967 atmVplLogicalPortEntry OBJECT-TYPE 1968 SYNTAX AtmVplLogicalPortEntry 1969 MAX-ACCESS not-accessible 1970 STATUS current 1971 DESCRIPTION 1972 "An entry with information about the ATM Logical Port 1973 interface." 1974 AUGMENTS { atmVplEntry } 1975 ::= { atmVplLogicalPortTable 1 } 1976 1977 AtmVplLogicalPortEntry ::= 1978 SEQUENCE { 1979 atmVplLogicalPortDef INTEGER, 1980 atmVplLogicalPortIndex InterfaceIndexOrZero 1981 } 1982 1983 atmVplLogicalPortDef OBJECT-TYPE 1984 SYNTAX INTEGER { 1985 notLogicalIf(1), 1986 isLogicalIf(2) 1987 } 1988 MAX-ACCESS read-create 1989 STATUS current 1990 DESCRIPTION 1991 "Indicates whether the VPC at this VPL interface is an ATM 1992 Logical Port interface." 1993 DEFVAL { notLogicalIf } 1994 ::= { atmVplLogicalPortEntry 1 } 1995 1996 atmVplLogicalPortIndex OBJECT-TYPE 1997 SYNTAX InterfaceIndexOrZero 1998 MAX-ACCESS read-only 1999 STATUS current 2000 DESCRIPTION 2001 "The ifTable index of the ATM logical port interface 2002 associated with this VPL. The distinguished value of zero 2003 indicates that the agent has not (yet) assigned such an 2004 ifTable Index. The zero value must be assigned by the agent 2005 if the value of atmVplLogicalPortDef is set to notLogicalIf, 2006 or if the VPL row is not active." 2007 2008 2009 2010 ::= { atmVplLogicalPortEntry 2 } 2011 2012 -- 11. ATM VCL Statistics Table 2013 2014 atmVclStatTable OBJECT-TYPE 2015 SYNTAX SEQUENCE OF AtmVclStatEntry 2016 MAX-ACCESS not-accessible 2017 STATUS current 2018 DESCRIPTION 2019 "This table contains all statistics counters per VCL. It is 2020 used to monitor the usage of the VCL in terms of incoming 2021 cells and outgoing cells." 2022 ::= { atm2MIBObjects 11 } 2023 2024 atmVclStatEntry OBJECT-TYPE 2025 SYNTAX AtmVclStatEntry 2026 MAX-ACCESS not-accessible 2027 STATUS current 2028 DESCRIPTION 2029 "Each entry in this table represents a VCL." 2030 INDEX { ifIndex, atmVclVpi, atmVclVci } 2031 ::= { atmVclStatTable 1 } 2032 2033 AtmVclStatEntry ::= 2034 SEQUENCE { 2035 atmVclStatTotalCellIns Counter32, 2036 atmVclStatClp0CellIns Counter32, 2037 atmVclStatTotalDiscards Counter32, 2038 atmVclStatClp0Discards Counter32, 2039 atmVclStatTotalCellOuts Counter32, 2040 atmVclStatClp0CellOuts Counter32, 2041 atmVclStatClp0Tagged Counter32 2042 } 2043 2044 atmVclStatTotalCellIns OBJECT-TYPE 2045 SYNTAX Counter32 2046 MAX-ACCESS read-only 2047 STATUS current 2048 DESCRIPTION 2049 "The total number of valid ATM cells received by this VCL 2050 including both CLP=0 and CLP=1 cells. The cells are counted 2051 prior to the application of the traffic policing." 2052 ::= { atmVclStatEntry 1 } 2053 2054 atmVclStatClp0CellIns OBJECT-TYPE 2055 SYNTAX Counter32 2056 MAX-ACCESS read-only 2057 STATUS current 2058 2059 2060 2061 DESCRIPTION 2062 "The number of valid ATM cells received by this VCL with 2063 CLP=0. The cells are counted prior to the application of 2064 the traffic policing." 2065 ::= { atmVclStatEntry 2 } 2066 2067 atmVclStatTotalDiscards OBJECT-TYPE 2068 SYNTAX Counter32 2069 MAX-ACCESS read-only 2070 STATUS current 2071 DESCRIPTION 2072 "The total number of valid ATM cells discarded by the 2073 traffic policing entity. This includes cells originally 2074 received with CLP=0 and CLP=1." 2075 ::= { atmVclStatEntry 3 } 2076 2077 atmVclStatClp0Discards OBJECT-TYPE 2078 SYNTAX Counter32 2079 MAX-ACCESS read-only 2080 STATUS current 2081 DESCRIPTION 2082 "The total number of valid ATM cells received with CLP=0 2083 and discarded by the traffic policing entity." 2084 ::= { atmVclStatEntry 4 } 2085 2086 atmVclStatTotalCellOuts OBJECT-TYPE 2087 SYNTAX Counter32 2088 MAX-ACCESS read-only 2089 STATUS current 2090 DESCRIPTION 2091 "The total number of valid ATM cells transmitted by this 2092 VCL. This includes both CLP=0 and CLP=1 cells." 2093 ::= { atmVclStatEntry 5 } 2094 2095 atmVclStatClp0CellOuts OBJECT-TYPE 2096 SYNTAX Counter32 2097 MAX-ACCESS read-only 2098 STATUS current 2099 DESCRIPTION 2100 "The total number of valid ATM cells transmitted with CLP=0 2101 by this VCL." 2102 ::= { atmVclStatEntry 6 } 2103 2104 atmVclStatClp0Tagged OBJECT-TYPE 2105 SYNTAX Counter32 2106 MAX-ACCESS read-only 2107 STATUS current 2108 DESCRIPTION 2109 2110 2111 2112 "The total number of valid ATM cells tagged by the traffic 2113 policing entity from CLP=0 to CLP=1." 2114 ::= { atmVclStatEntry 7 } 2115 2116 -- 12. ATM AAL5 per-VCC Statistics Table 2117 2118 atmAal5VclStatTable OBJECT-TYPE 2119 SYNTAX SEQUENCE OF AtmAal5VclStatEntry 2120 MAX-ACCESS not-accessible 2121 STATUS current 2122 DESCRIPTION 2123 "This table provides a collection of objects providing AAL5 2124 configuration and performance statistics of a VCL." 2125 ::= { atm2MIBObjects 12 } 2126 2127 atmAal5VclStatEntry OBJECT-TYPE 2128 SYNTAX AtmAal5VclStatEntry 2129 MAX-ACCESS not-accessible 2130 STATUS current 2131 DESCRIPTION 2132 "Each entry in this table represents an AAL5 VCL, and 2133 is indexed by ifIndex values of AAL5 interfaces and 2134 the associated VPI/VCI values." 2135 INDEX { ifIndex, atmVclVpi, atmVclVci } 2136 ::= { atmAal5VclStatTable 1 } 2137 2138 AtmAal5VclStatEntry ::= 2139 SEQUENCE { 2140 atmAal5VclInPkts Counter32, 2141 atmAal5VclOutPkts Counter32, 2142 atmAal5VclInOctets Counter32, 2143 atmAal5VclOutOctets Counter32 2144 } 2145 2146 atmAal5VclInPkts OBJECT-TYPE 2147 SYNTAX Counter32 2148 MAX-ACCESS read-only 2149 STATUS current 2150 DESCRIPTION 2151 "The number of AAL5 CPCS PDUs received on the AAL5 VCC at 2152 the interface identified by the ifIndex." 2153 ::= { atmAal5VclStatEntry 1 } 2154 2155 atmAal5VclOutPkts OBJECT-TYPE 2156 SYNTAX Counter32 2157 MAX-ACCESS read-only 2158 STATUS current 2159 DESCRIPTION 2160 2161 2162 2163 "The number of AAL5 CPCS PDUs transmitted on the AAL5 VCC 2164 at the interface identified by the ifIndex." 2165 ::= { atmAal5VclStatEntry 2 } 2166 2167 atmAal5VclInOctets OBJECT-TYPE 2168 SYNTAX Counter32 2169 MAX-ACCESS read-only 2170 STATUS current 2171 DESCRIPTION 2172 "The number of octets contained in AAL5 CPCS PDUs received 2173 on the AAL5 VCC at the interface identified by the ifIndex." 2174 ::= { atmAal5VclStatEntry 3 } 2175 2176 atmAal5VclOutOctets OBJECT-TYPE 2177 SYNTAX Counter32 2178 MAX-ACCESS read-only 2179 STATUS current 2180 DESCRIPTION 2181 "The number of octets contained in AAL5 CPCS PDUs 2182 transmitted on the AAL5 VCC at the interface identified by 2183 the ifIndex." 2184 ::= { atmAal5VclStatEntry 4 } 2185 2186 -- 13. ATM VC General Information Table 2187 2188 atmVclGenTable OBJECT-TYPE 2189 SYNTAX SEQUENCE OF AtmVclGenEntry 2190 MAX-ACCESS not-accessible 2191 STATUS current 2192 DESCRIPTION 2193 "General Information for each VC." 2194 ::= { atm2MIBObjects 13 } 2195 2196 atmVclGenEntry OBJECT-TYPE 2197 SYNTAX AtmVclGenEntry 2198 MAX-ACCESS not-accessible 2199 STATUS current 2200 DESCRIPTION 2201 "An entry with general information about the ATM VC." 2202 2203 AUGMENTS { atmVclEntry } 2204 ::= { atmVclGenTable 1 } 2205 2206 AtmVclGenEntry ::= 2207 SEQUENCE { 2208 atmVclGenSigDescrIndex AtmSigDescrParamIndex 2209 } 2210 2211 2212 2213 2214 atmVclGenSigDescrIndex OBJECT-TYPE 2215 SYNTAX AtmSigDescrParamIndex 2216 MAX-ACCESS read-create 2217 STATUS current 2218 DESCRIPTION 2219 "The value of this object identifies the row in the ATM 2220 Signalling Descriptor Parameter Table which applies to this 2221 VCL." 2222 ::= { atmVclGenEntry 1 } 2223 2224 -- 14. ATM Interface Configuration Extension Table 2225 2226atmInterfaceExtTable OBJECT-TYPE 2227 SYNTAX SEQUENCE OF AtmInterfaceExtEntry 2228 MAX-ACCESS not-accessible 2229 STATUS current 2230 DESCRIPTION 2231 "This table contains ATM interface configuration and monitoring 2232 information not defined in the atmInterfaceConfTable from the 2233 ATM-MIB. This includes the type of connection setup procedures, 2234 ILMI information, and information on the VPI/VCI range." 2235 REFERENCE 2236 "Tesink, K., Editor, Definitions of Managed Objects 2237 for ATM Management, RFC 2515, Bell Communications 2238 Research, February, 1999." 2239 ::= { atm2MIBObjects 14 } 2240 2241atmInterfaceExtEntry OBJECT-TYPE 2242 SYNTAX AtmInterfaceExtEntry 2243 MAX-ACCESS not-accessible 2244 STATUS current 2245 DESCRIPTION 2246 "An entry extends the atmInterfaceConfEntry defined in the ATM- 2247 MIB. Each entry corresponds to an ATM interface." 2248 REFERENCE 2249 "Tesink, K., Editor, Definitions of Managed Objects 2250 for ATM Management, RFC 2515, Bell Communications 2251 Research, February, 1999." 2252 AUGMENTS { atmInterfaceConfEntry } 2253 ::= { atmInterfaceExtTable 1 } 2254 2255AtmInterfaceExtEntry ::= SEQUENCE { 2256 atmIntfConfigType AtmInterfaceType, 2257 atmIntfActualType AtmInterfaceType, 2258 atmIntfConfigSide INTEGER, 2259 atmIntfActualSide INTEGER, 2260 atmIntfIlmiAdminStatus BITS, 2261 atmIntfIlmiOperStatus BITS, 2262 2263 2264 2265 atmIntfIlmiFsmState INTEGER, 2266 atmIntfIlmiEstablishConPollIntvl Integer32, 2267 atmIntfIlmiCheckConPollIntvl Integer32, 2268 atmIntfIlmiConPollInactFactor Integer32, 2269 atmIntfIlmiPublicPrivateIndctr INTEGER, 2270 atmInterfaceConfMaxSvpcVpi INTEGER, 2271 atmInterfaceCurrentMaxSvpcVpi INTEGER, 2272 atmInterfaceConfMaxSvccVpi INTEGER, 2273 atmInterfaceCurrentMaxSvccVpi INTEGER, 2274 atmInterfaceConfMinSvccVci INTEGER, 2275 atmInterfaceCurrentMinSvccVci INTEGER, 2276 atmIntfSigVccRxTrafficDescrIndex 2277 AtmTrafficDescrParamIndex, 2278 atmIntfSigVccTxTrafficDescrIndex 2279 AtmTrafficDescrParamIndex, 2280 atmIntfPvcFailures Counter32, 2281 atmIntfCurrentlyFailingPVpls Gauge32, 2282 atmIntfCurrentlyFailingPVcls Gauge32, 2283 atmIntfPvcFailuresTrapEnable TruthValue, 2284 atmIntfPvcNotificationInterval INTEGER, 2285 atmIntfLeafSetupFailures Counter32, 2286 atmIntfLeafSetupRequests Counter32 } 2287 2288atmIntfConfigType OBJECT-TYPE 2289 SYNTAX AtmInterfaceType 2290 MAX-ACCESS read-write 2291 STATUS current 2292 DESCRIPTION 2293 "The type of connection setup procedures configured for the ATM 2294 interface. Setting this variable to a value of 'other' is not 2295 allowed." 2296 DEFVAL { autoConfig } 2297 ::= { atmInterfaceExtEntry 1 } 2298 2299atmIntfActualType OBJECT-TYPE 2300 SYNTAX AtmInterfaceType 2301 MAX-ACCESS read-only 2302 STATUS current 2303 DESCRIPTION 2304 "The type of connection setup procedures currently being used on 2305 the interface. This may reflect a manually configured value for 2306 the interface type, or may be determined by other means such as 2307 auto-configuration. A value of `autoConfig' indicates that 2308 auto-configuration was requested but has not yet been completed." 2309 ::= { atmInterfaceExtEntry 2 } 2310 2311atmIntfConfigSide OBJECT-TYPE 2312 SYNTAX INTEGER { 2313 2314 2315 2316 other(1), 2317 user(2), 2318 network(3) } 2319 MAX-ACCESS read-write 2320 STATUS current 2321 DESCRIPTION 2322 "The configured role of the managed entity as one side of the ATM 2323 interface. This value does not apply when the object 2324 atmIntfConfigType is set to `autoConfig', `atmfPnni1Dot0', or 2325 `atmfBici2Dot0'." 2326 ::= { atmInterfaceExtEntry 3 } 2327 2328atmIntfActualSide OBJECT-TYPE 2329 SYNTAX INTEGER { 2330 other(1), 2331 user(2), 2332 network(3), 2333 symmetric(4) } 2334 MAX-ACCESS read-only 2335 STATUS current 2336 DESCRIPTION 2337 "The current role used by the managed entity to represent one 2338 side of the ATM interface." 2339 ::= { atmInterfaceExtEntry 4 } 2340 2341atmIntfIlmiAdminStatus OBJECT-TYPE 2342 SYNTAX BITS { ilmi(0), 2343 ilmiAddressRegistration(1), 2344 ilmiConnectivity(2), 2345 ilmiPvcPvpMgmt(3), 2346 ilmiSigVccParamNegotiation(4) } 2347 MAX-ACCESS read-write 2348 STATUS current 2349 DESCRIPTION 2350 "Indicates which components of ILMI are administratively enabled 2351 on this interface. If the 'ilmi' bit is not set, then no ILMI 2352 components are operational. ILMI components other than auto- 2353 configuration that are not represented in the value have their 2354 administrative status determined according to the 'ilmi' bit. 2355 The ILMI auto-configuration component is enabled/disabled by the 2356 atmIntfConfigType object." 2357 ::= { atmInterfaceExtEntry 5 } 2358 2359atmIntfIlmiOperStatus OBJECT-TYPE 2360 SYNTAX BITS { ilmi(0), 2361 ilmiAddressRegistration(1), 2362 ilmiConnectivity(2), 2363 ilmiPvcPvpMgmt(3), 2364 2365 2366 2367 ilmiSigVccParamNegotiation(4) } 2368 MAX-ACCESS read-only 2369 STATUS current 2370 DESCRIPTION 2371 "Indicates which components of ILMI are operational on this 2372 interface." 2373 ::= { atmInterfaceExtEntry 6 } 2374 2375atmIntfIlmiFsmState OBJECT-TYPE 2376 SYNTAX INTEGER { stopped(1), 2377 linkFailing(2), 2378 establishing(3), 2379 configuring(4), 2380 retrievingNetworkPrefixes(5), 2381 registeringNetworkPrefixes(6), 2382 retrievingAddresses(7), 2383 registeringAddresses(8), 2384 verifying(9) } 2385 MAX-ACCESS read-only 2386 STATUS current 2387 DESCRIPTION 2388 "Indicates the state of the ILMI Finite State Machine associated 2389 with this interface." 2390 2391 REFERENCE 2392 "ATM Forum, Integrated Local Management Interface 2393 (ILMI) Specification, Version 4.0, af-ilmi-0065.000, 2394 September 1996, Appendix 1" 2395 ::= { atmInterfaceExtEntry 7 } 2396 2397atmIntfIlmiEstablishConPollIntvl OBJECT-TYPE 2398 SYNTAX Integer32 (1..65535) 2399 UNITS "seconds" 2400 MAX-ACCESS read-write 2401 STATUS current 2402 DESCRIPTION 2403 "The amount of time S between successive transmissions of ILMI 2404 messages on this interface for the purpose of detecting 2405 establishment of ILMI connectivity." 2406 REFERENCE 2407 "ATM Forum, Integrated Local Management Interface 2408 (ILMI) Specification, Version 4.0, af-ilmi-0065.000, 2409 September 1996, Section 8.3.1" 2410 DEFVAL { 1 } 2411 ::= { atmInterfaceExtEntry 8 } 2412 2413atmIntfIlmiCheckConPollIntvl OBJECT-TYPE 2414 SYNTAX Integer32 (0..65535) 2415 2416 2417 2418 UNITS "seconds" 2419 MAX-ACCESS read-write 2420 STATUS current 2421 DESCRIPTION 2422 "The amount of time T between successive transmissions of ILMI 2423 messages on this interface for the purpose of detecting loss of 2424 ILMI connectivity. The distinguished value zero disables ILMI 2425 connectivity procedures on this interface." 2426 REFERENCE 2427 "ATM Forum, Integrated Local Management Interface 2428 (ILMI) Specification, Version 4.0, af-ilmi-0065.000, 2429 September 1996, Section 8.3.1" 2430 DEFVAL { 5 } 2431 ::= { atmInterfaceExtEntry 9 } 2432 2433atmIntfIlmiConPollInactFactor OBJECT-TYPE 2434 SYNTAX Integer32 (0..65535) 2435 MAX-ACCESS read-write 2436 STATUS current 2437 DESCRIPTION 2438 "The number K of consecutive polls on this interface for which no 2439 ILMI response message is received before ILMI connectivity is 2440 declared lost." 2441 REFERENCE 2442 "ATM Forum, Integrated Local Management Interface 2443 (ILMI) Specification, Version 4.0, af-ilmi-0065.000, 2444 September 1996, Section 8.3.1" 2445 DEFVAL { 4 } 2446 ::= { atmInterfaceExtEntry 10 } 2447 2448atmIntfIlmiPublicPrivateIndctr OBJECT-TYPE 2449 SYNTAX INTEGER { 2450 other(1), 2451 public(2), 2452 private(3) 2453 } 2454 MAX-ACCESS read-write 2455 STATUS current 2456 DESCRIPTION 2457 "Specifies whether this end of the interface is advertised in 2458 ILMI as a device of the `public' or `private' type." 2459 DEFVAL { private } 2460 ::= { atmInterfaceExtEntry 11 } 2461 2462atmInterfaceConfMaxSvpcVpi OBJECT-TYPE 2463 SYNTAX INTEGER (0..4095) 2464 MAX-ACCESS read-write 2465 STATUS current 2466 2467 2468 2469 DESCRIPTION 2470 "The maximum VPI that the signalling stack on the ATM interface 2471 is configured to support for allocation to switched virtual path 2472 connections." 2473 ::= { atmInterfaceExtEntry 12 } 2474 2475atmInterfaceCurrentMaxSvpcVpi OBJECT-TYPE 2476 SYNTAX INTEGER (0..4095) 2477 MAX-ACCESS read-only 2478 STATUS current 2479 DESCRIPTION 2480 "The maximum VPI that the signalling stack on the ATM interface 2481 may currently allocate to switched virtual path connections. 2482 This value is the minimum of atmInterfaceConfMaxSvpcVpi, and the 2483 atmInterfaceMaxSvpcVpi of the interface's UNI/NNI peer. 2484 2485 If the interface does not negotiate with its peer to determine 2486 the maximum VPI that can be allocated to SVPCs on the interface, 2487 then the value of this object must equal 2488 atmInterfaceConfMaxSvpcVpi. " 2489 ::= { atmInterfaceExtEntry 13 } 2490 2491atmInterfaceConfMaxSvccVpi OBJECT-TYPE 2492 SYNTAX INTEGER (0..4095) 2493 MAX-ACCESS read-write 2494 STATUS current 2495 DESCRIPTION 2496 "The maximum VPI that the signalling stack on the ATM interface 2497 is configured to support for allocation to switched virtual 2498 channel connections." 2499 ::= { atmInterfaceExtEntry 14 } 2500 2501atmInterfaceCurrentMaxSvccVpi OBJECT-TYPE 2502 SYNTAX INTEGER (0..4095) 2503 MAX-ACCESS read-only 2504 STATUS current 2505 DESCRIPTION 2506 "The maximum VPI that the signalling stack on the ATM interface 2507 may currently allocate to switched virtual channel connections. 2508 This value is the minimum of atmInterfaceConfMaxSvccVpi, and the 2509 atmInterfaceConfMaxSvccVpi of the interface's UNI/NNI peer. 2510 2511 If the interface does not negotiate with its peer to determine 2512 the maximum VPI that can be allocated to SVCCs on the interface, 2513 then the value of this object must equal 2514 atmInterfaceConfMaxSvccVpi." 2515 ::= { atmInterfaceExtEntry 15 } 2516 2517 2518 2519 2520atmInterfaceConfMinSvccVci OBJECT-TYPE 2521 SYNTAX INTEGER (0..65535) 2522 MAX-ACCESS read-write 2523 STATUS current 2524 DESCRIPTION 2525 "The minimum VCI that the signalling stack on the ATM interface 2526 is configured to support for allocation to switched virtual 2527 channel connections." 2528 ::= { atmInterfaceExtEntry 16 } 2529 2530atmInterfaceCurrentMinSvccVci OBJECT-TYPE 2531 SYNTAX INTEGER (0..65535) 2532 MAX-ACCESS read-only 2533 STATUS current 2534 DESCRIPTION 2535 "The minimum VCI that the signalling stack on the ATM interface 2536 may currently allocate to switched virtual channel connections. 2537 This value is the maximum of atmInterfaceConfMinSvccVci, and the 2538 atmInterfaceConfMinSvccVci of the interface's UNI/NNI peer. 2539 If the interface does not negotiate with its peer to determine 2540 the minimum VCI that can be allocated to SVCCs on the interface, 2541 then the value of this object must equal 2542 atmInterfaceConfMinSvccVci." 2543 ::= { atmInterfaceExtEntry 17 } 2544 2545atmIntfSigVccRxTrafficDescrIndex OBJECT-TYPE 2546 SYNTAX AtmTrafficDescrParamIndex 2547 MAX-ACCESS read-write 2548 STATUS current 2549 DESCRIPTION 2550 "This object identifies the row in the atmTrafficDescrParamTable 2551 used during ILMI auto-configuration to specify the advertised 2552 signalling VCC traffic parameters for the receive direction. 2553 The traffic descriptor resulting from ILMI auto-configuration of 2554 the signalling VCC is indicated in the atmVclTable." 2555 ::= { atmInterfaceExtEntry 18 } 2556 2557atmIntfSigVccTxTrafficDescrIndex OBJECT-TYPE 2558 SYNTAX AtmTrafficDescrParamIndex 2559 MAX-ACCESS read-write 2560 STATUS current 2561 DESCRIPTION 2562 "This object identifies the row in the atmTrafficDescrParamTable 2563 used during ILMI auto-configuration to specify the advertised 2564 signalling VCC traffic parameters for the transmit direction. 2565 The traffic descriptor resulting from ILMI auto-configuration of 2566 the signalling VCC is indicated in the atmVclTable." 2567 ::= { atmInterfaceExtEntry 19 } 2568 2569 2570 2571atmIntfPvcFailures OBJECT-TYPE 2572 SYNTAX Counter32 2573 MAX-ACCESS read-only 2574 STATUS current 2575 DESCRIPTION 2576 "The number of times the operational status of a PVPL or PVCL on 2577 this interface has gone down." 2578 ::= { atmInterfaceExtEntry 20 } 2579 2580atmIntfCurrentlyFailingPVpls OBJECT-TYPE 2581 SYNTAX Gauge32 2582 MAX-ACCESS read-only 2583 STATUS current 2584 DESCRIPTION 2585 "The current number of VPLs on this interface for which there is 2586 an active row in the atmVplTable having an atmVplConnKind value 2587 of `pvc' and an atmVplOperStatus with a value other than `up'." 2588 ::= { atmInterfaceExtEntry 21 } 2589 2590atmIntfCurrentlyFailingPVcls OBJECT-TYPE 2591 SYNTAX Gauge32 2592 MAX-ACCESS read-only 2593 STATUS current 2594 DESCRIPTION 2595 "The current number of VCLs on this interface for which there is 2596 an active row in the atmVclTable having an atmVclConnKind value 2597 of `pvc' and an atmVclOperStatus with a value other than `up'." 2598 ::= { atmInterfaceExtEntry 22 } 2599 2600atmIntfPvcFailuresTrapEnable OBJECT-TYPE 2601 SYNTAX TruthValue 2602 MAX-ACCESS read-write 2603 STATUS current 2604 DESCRIPTION 2605 "Allows the generation of traps in response to PVCL or PVPL 2606 failures on this interface." 2607 DEFVAL { false } 2608 ::= { atmInterfaceExtEntry 23 } 2609 2610atmIntfPvcNotificationInterval OBJECT-TYPE 2611 SYNTAX INTEGER (1..3600) 2612 UNITS "seconds" 2613 MAX-ACCESS read-write 2614 STATUS current 2615 DESCRIPTION 2616 "The minimum interval between the sending of 2617 atmIntfPvcFailuresTrap notifications for this interface." 2618 DEFVAL { 30 } 2619 2620 2621 2622 ::= { atmInterfaceExtEntry 24 } 2623 2624atmIntfLeafSetupFailures OBJECT-TYPE 2625 SYNTAX Counter32 2626 MAX-ACCESS read-only 2627 STATUS current 2628 DESCRIPTION 2629 "Number of setup failures. For root, this is the number of 2630 rejected setup requests and for leaf, this is the number of setup 2631 failure received." 2632 ::= { atmInterfaceExtEntry 25 } 2633 2634atmIntfLeafSetupRequests OBJECT-TYPE 2635 SYNTAX Counter32 2636 MAX-ACCESS read-only 2637 STATUS current 2638 DESCRIPTION 2639 "Number of setup requests. For root, this includes both incoming 2640 setup request and root intiated setup requests." 2641 ::= { atmInterfaceExtEntry 26 } 2642 2643 -- 15. ATM ILMI Service Registry Table 2644 2645atmIlmiSrvcRegTable OBJECT-TYPE 2646 SYNTAX SEQUENCE OF AtmIlmiSrvcRegEntry 2647 MAX-ACCESS not-accessible 2648 STATUS current 2649 DESCRIPTION 2650 "This table contains a list of all the ATM network services known 2651 by this device. 2652 2653 The characteristics of these services are made available through 2654 the ILMI, using the ILMI general-purpose service registry MIB. 2655 These services may be made available to all ATM interfaces 2656 (atmIlmiSrvcRegIndex = 0) or to some specific ATM interfaces only 2657 (atmIlmiSrvcRegIndex = ATM interface index)." 2658 ::= { atm2MIBObjects 15 } 2659 2660atmIlmiSrvcRegEntry OBJECT-TYPE 2661 SYNTAX AtmIlmiSrvcRegEntry 2662 MAX-ACCESS not-accessible 2663 STATUS current 2664 DESCRIPTION 2665 "Information about a single service provider that is available to 2666 the user-side of an adjacent device through the ILMI. 2667 2668 Implementors need to be aware that if the size of the 2669 atmIlmiSrvcRegServiceID exceeds 112 sub-identifiers then OIDs of 2670 2671 2672 2673 column instances in this table will have more than 128 sub- 2674 identifiers and cannot be accessed using SNMPv1, SNMPv2, or 2675 SNMPv3." 2676 2677 INDEX { atmIlmiSrvcRegIndex, 2678 atmIlmiSrvcRegServiceID, 2679 atmIlmiSrvcRegAddressIndex } 2680 ::= { atmIlmiSrvcRegTable 1 } 2681 2682AtmIlmiSrvcRegEntry ::= SEQUENCE { 2683 atmIlmiSrvcRegIndex InterfaceIndexOrZero, 2684 atmIlmiSrvcRegServiceID OBJECT IDENTIFIER, 2685 atmIlmiSrvcRegAddressIndex INTEGER, 2686 atmIlmiSrvcRegATMAddress AtmAddr, 2687 atmIlmiSrvcRegParm1 OCTET STRING, 2688 atmIlmiSrvcRegRowStatus RowStatus 2689 } 2690 2691atmIlmiSrvcRegIndex OBJECT-TYPE 2692 SYNTAX InterfaceIndexOrZero 2693 MAX-ACCESS not-accessible 2694 STATUS current 2695 DESCRIPTION 2696 "The ATM interface where the service defined in this entry can be 2697 made available to an ATM device attached to this interface. 2698 2699 The value of 0 has a special meaning: when an ATM service is 2700 defined in an entry whose atmIlmiSrvcRegIndex is zero, the ATM 2701 service is available to ATM devices connected to any ATM 2702 interface. (default value(s)). 2703 2704 When the user-side of an adjacent device queries the content of 2705 the ILMI service registry MIB (using the ILMI protocol), the 2706 local network-side responds with the ATM services defined in 2707 atmIlmiSrvcRegTable entries, provided that these entries are 2708 indexed by: 2709 2710 - the corresponding ifIndex value (atmIlmiSrvcRegIndex 2711 equal to the ifIndex of the interface to which the 2712 adjacent device is connected) - zero (atmIlmiSrvcRegIndex=0)." 2713 ::= { atmIlmiSrvcRegEntry 1 } 2714 2715atmIlmiSrvcRegServiceID OBJECT-TYPE 2716 SYNTAX OBJECT IDENTIFIER 2717 MAX-ACCESS not-accessible 2718 STATUS current 2719 DESCRIPTION 2720 "This is the service identifier which uniquely identifies the 2721 2722 2723 2724 type of service at the address provided in the table. The object 2725 identifiers for the LAN Emulation Configuration Server (LECS) and 2726 the ATM Name Server (ANS) are defined in the ATM Forum ILMI 2727 Service Registry MIB. The object identifiers for the ATMARP 2728 Server, the Multicast Address Resolution Server (MARS), and the 2729 NHRP Server (NHS) are defined in RFC 2601, RFC 2602, and RFC 2730 2603, respectively." 2731 ::= { atmIlmiSrvcRegEntry 2 } 2732 2733atmIlmiSrvcRegAddressIndex OBJECT-TYPE 2734 SYNTAX INTEGER (1..2147483647) 2735 MAX-ACCESS not-accessible 2736 STATUS current 2737 DESCRIPTION 2738 "An arbitrary integer to differentiate multiple rows containing 2739 different ATM addresses for the same service on the same 2740 interface. This number need NOT be the same as the corresponding 2741 ILMI atmfSrvcRegAddressIndex MIB object." 2742 ::= { atmIlmiSrvcRegEntry 3 } 2743 2744atmIlmiSrvcRegATMAddress OBJECT-TYPE 2745 SYNTAX AtmAddr 2746 MAX-ACCESS read-create 2747 STATUS current 2748 DESCRIPTION 2749 "This is the full address of the service. The user-side of the 2750 adjacent device may use this address to establish a connection 2751 with the service." 2752 ::= { atmIlmiSrvcRegEntry 4 } 2753 2754atmIlmiSrvcRegParm1 OBJECT-TYPE 2755 SYNTAX OCTET STRING (SIZE(1..255)) 2756 MAX-ACCESS read-create 2757 STATUS current 2758 DESCRIPTION 2759 "An octet string used according to the value of 2760 atmIlmiSrvcRegServiceID." 2761 ::= { atmIlmiSrvcRegEntry 5 } 2762 2763atmIlmiSrvcRegRowStatus OBJECT-TYPE 2764 SYNTAX RowStatus 2765 MAX-ACCESS read-create 2766 STATUS current 2767 DESCRIPTION 2768 "This object is used to create or destroy an entry from this 2769 table." 2770 ::= { atmIlmiSrvcRegEntry 6 } 2771 2772 2773 2774 2775 -- 16. ILMI Network Prefix Table 2776 2777atmIlmiNetworkPrefixTable OBJECT-TYPE 2778 SYNTAX SEQUENCE OF AtmIlmiNetworkPrefixEntry 2779 MAX-ACCESS not-accessible 2780 STATUS current 2781 DESCRIPTION 2782 "A table specifying per-interface network prefix(es) supplied by 2783 the network side of the UNI during ILMI address registration. 2784 When no network prefixes are specified for a particular 2785 interface, one or more network prefixes based on the switch 2786 address(es) may be used for ILMI address registration." 2787 ::= { atm2MIBObjects 16 } 2788 2789atmIlmiNetworkPrefixEntry OBJECT-TYPE 2790 SYNTAX AtmIlmiNetworkPrefixEntry 2791 MAX-ACCESS not-accessible 2792 STATUS current 2793 DESCRIPTION 2794 "Information about a single network prefix supplied by the 2795 network side of the UNI during ILMI address registration. Note 2796 that the index variable atmIlmiNetPrefixPrefix is a variable- 2797 length string, and as such the rule for variable-length strings 2798 in section 7.7 of RFC 2578 applies." 2799 INDEX { ifIndex, 2800 atmIlmiNetPrefixPrefix } 2801 ::= { atmIlmiNetworkPrefixTable 1 } 2802 2803AtmIlmiNetworkPrefixEntry ::= 2804 SEQUENCE { 2805 atmIlmiNetPrefixPrefix AtmIlmiNetworkPrefix, 2806 atmIlmiNetPrefixRowStatus RowStatus 2807 } 2808 2809atmIlmiNetPrefixPrefix OBJECT-TYPE 2810 SYNTAX AtmIlmiNetworkPrefix 2811 MAX-ACCESS not-accessible 2812 STATUS current 2813 DESCRIPTION 2814 "The network prefix specified for use in ILMI address 2815 registration." 2816 ::= { atmIlmiNetworkPrefixEntry 1 } 2817 2818atmIlmiNetPrefixRowStatus OBJECT-TYPE 2819 SYNTAX RowStatus 2820 MAX-ACCESS read-create 2821 STATUS current 2822 DESCRIPTION 2823 2824 2825 2826 "Used to create, delete, activate and de-activate network 2827 prefixes used in ILMI address registration." 2828 2829 ::= { atmIlmiNetworkPrefixEntry 2 } 2830 2831 -- 17. ATM Switch Address Table 2832 2833atmSwitchAddressTable OBJECT-TYPE 2834 SYNTAX SEQUENCE OF AtmSwitchAddressEntry 2835 MAX-ACCESS not-accessible 2836 STATUS current 2837 DESCRIPTION 2838 "This table contains one or more ATM endsystem addresses on a 2839 per-switch basis. These addresses are used to identify the 2840 switch. When no ILMI network prefixes are configured for certain 2841 interfaces, network prefixes based on the switch address(es) may 2842 be used for ILMI address registration." 2843 ::= { atm2MIBObjects 17 } 2844 2845atmSwitchAddressEntry OBJECT-TYPE 2846 SYNTAX AtmSwitchAddressEntry 2847 MAX-ACCESS not-accessible 2848 STATUS current 2849 DESCRIPTION 2850 "An entry in the ATM Switch Address table." 2851 INDEX { atmSwitchAddressIndex } 2852 ::= { atmSwitchAddressTable 1 } 2853 2854AtmSwitchAddressEntry ::= 2855 SEQUENCE { 2856 atmSwitchAddressIndex Integer32, 2857 atmSwitchAddressAddress OCTET STRING, 2858 atmSwitchAddressRowStatus RowStatus 2859 } 2860 2861atmSwitchAddressIndex OBJECT-TYPE 2862 SYNTAX Integer32 (1..65535) 2863 MAX-ACCESS not-accessible 2864 STATUS current 2865 DESCRIPTION 2866 "An arbitrary index used to enumerate the ATM endsystem addresses 2867 for this switch." 2868 ::= { atmSwitchAddressEntry 1 } 2869 2870atmSwitchAddressAddress OBJECT-TYPE 2871 SYNTAX OCTET STRING (SIZE(13|20)) 2872 MAX-ACCESS read-create 2873 STATUS current 2874 2875 2876 2877 DESCRIPTION 2878 "An ATM endsystem address or address prefix used to identify this 2879 switch. When no ESI or SEL field is specified, the switch may 2880 generate the ESI and SEL fields automatically to obtain a 2881 complete 20-byte ATM endsystem address." 2882 ::= { atmSwitchAddressEntry 2 } 2883 2884atmSwitchAddressRowStatus OBJECT-TYPE 2885 SYNTAX RowStatus 2886 MAX-ACCESS read-create 2887 STATUS current 2888 DESCRIPTION 2889 "Used to create, delete, activate, and de-activate addresses used 2890 to identify this switch." 2891 ::= { atmSwitchAddressEntry 3 } 2892 2893 -- 18. ATM VP Cross-Connect Extension Table 2894 2895atmVpCrossConnectXTable OBJECT-TYPE 2896 SYNTAX SEQUENCE OF AtmVpCrossConnectXEntry 2897 MAX-ACCESS not-accessible 2898 STATUS current 2899 DESCRIPTION 2900 "This table contains one row per VP Cross-Connect represented in 2901 the atmVpCrossConnectTable." 2902 ::= { atm2MIBObjects 18 } 2903 2904atmVpCrossConnectXEntry OBJECT-TYPE 2905 SYNTAX AtmVpCrossConnectXEntry 2906 MAX-ACCESS not-accessible 2907 STATUS current 2908 DESCRIPTION 2909 "Information about a particular ATM VP Cross-Connect. 2910 Each entry provides an two objects that name the Cross-Connect. 2911 One is assigned by the Service User and the other by the Service 2912 Provider." 2913 AUGMENTS { atmVpCrossConnectEntry } 2914 ::= { atmVpCrossConnectXTable 1 } 2915 2916AtmVpCrossConnectXEntry ::= SEQUENCE { 2917 atmVpCrossConnectUserName SnmpAdminString, 2918 atmVpCrossConnectProviderName SnmpAdminString 2919} 2920 2921atmVpCrossConnectUserName OBJECT-TYPE 2922 SYNTAX SnmpAdminString (SIZE(0..255)) 2923 MAX-ACCESS read-create 2924 STATUS current 2925 2926 2927 2928 DESCRIPTION 2929 "This is a service user assigned textual representation of a VPC 2930 PVC." 2931 ::= { atmVpCrossConnectXEntry 1 } 2932 2933atmVpCrossConnectProviderName OBJECT-TYPE 2934 SYNTAX SnmpAdminString (SIZE(0..255)) 2935 MAX-ACCESS read-only 2936 STATUS current 2937 DESCRIPTION 2938 "This is a system supplied textual representation of VPC PVC. It 2939 is assigned by the service provider." 2940 ::= { atmVpCrossConnectXEntry 2 } 2941 2942 -- 19. ATM VC Cross-Connect Extension Table 2943 2944atmVcCrossConnectXTable OBJECT-TYPE 2945 SYNTAX SEQUENCE OF AtmVcCrossConnectXEntry 2946 MAX-ACCESS not-accessible 2947 STATUS current 2948 DESCRIPTION 2949 "This table contains one row per VC Cross-Connect represented in 2950 the atmVcCrossConnectTable." 2951 ::= { atm2MIBObjects 19 } 2952 2953atmVcCrossConnectXEntry OBJECT-TYPE 2954 SYNTAX AtmVcCrossConnectXEntry 2955 MAX-ACCESS not-accessible 2956 STATUS current 2957 DESCRIPTION 2958 "Information about a particular ATM VC Cross-Connect. 2959 Each entry provides an two objects that name the Cross-Connect. 2960 One is assigned by the Service User and the other by the Service 2961 Provider." 2962 AUGMENTS { atmVcCrossConnectEntry } 2963 ::= { atmVcCrossConnectXTable 1 } 2964 2965AtmVcCrossConnectXEntry ::= SEQUENCE { 2966 atmVcCrossConnectUserName SnmpAdminString, 2967 atmVcCrossConnectProviderName SnmpAdminString 2968} 2969 2970atmVcCrossConnectUserName OBJECT-TYPE 2971 SYNTAX SnmpAdminString (SIZE(0..255)) 2972 MAX-ACCESS read-create 2973 STATUS current 2974 DESCRIPTION 2975 "This is a service user assigned textual representation of a VCC 2976 2977 2978 2979 PVC." 2980 ::= { atmVcCrossConnectXEntry 1 } 2981 2982atmVcCrossConnectProviderName OBJECT-TYPE 2983 SYNTAX SnmpAdminString (SIZE(0..255)) 2984 MAX-ACCESS read-only 2985 STATUS current 2986 DESCRIPTION 2987 "This is a system supplied textual representation of VCC PVC. It 2988 is assigned by the service provider." 2989 ::= { atmVcCrossConnectXEntry 2 } 2990 2991 2992 -- 20. Currently Failing PVPL Table 2993 2994atmCurrentlyFailingPVplTable OBJECT-TYPE 2995 SYNTAX SEQUENCE OF AtmCurrentlyFailingPVplEntry 2996 MAX-ACCESS not-accessible 2997 STATUS current 2998 DESCRIPTION 2999 "A table indicating all VPLs for which there is an active row in 3000 the atmVplTable having an atmVplConnKind value of `pvc' and an 3001 atmVplOperStatus with a value other than `up'." 3002 ::= { atm2MIBObjects 20 } 3003 3004atmCurrentlyFailingPVplEntry OBJECT-TYPE 3005 SYNTAX AtmCurrentlyFailingPVplEntry 3006 MAX-ACCESS not-accessible 3007 STATUS current 3008 DESCRIPTION 3009 "Each entry in this table represents a VPL for which the 3010 atmVplRowStatus is `active', the atmVplConnKind is `pvc', and the 3011 atmVplOperStatus is other than `up'." 3012 INDEX { ifIndex, atmVplVpi } 3013 ::= { atmCurrentlyFailingPVplTable 1 } 3014 3015AtmCurrentlyFailingPVplEntry ::= 3016 SEQUENCE { 3017 atmCurrentlyFailingPVplTimeStamp TimeStamp 3018 } 3019 3020atmCurrentlyFailingPVplTimeStamp OBJECT-TYPE 3021 SYNTAX TimeStamp 3022 MAX-ACCESS read-only 3023 STATUS current 3024 DESCRIPTION 3025 "The time at which this PVPL began to fail." 3026 ::= { atmCurrentlyFailingPVplEntry 1 } 3027 3028 3029 3030 -- 21. Currently Failing PVCL Table 3031 3032atmCurrentlyFailingPVclTable OBJECT-TYPE 3033 SYNTAX SEQUENCE OF AtmCurrentlyFailingPVclEntry 3034 MAX-ACCESS not-accessible 3035 STATUS current 3036 DESCRIPTION 3037 "A table indicating all VCLs for which there is an active row in 3038 the atmVclTable having an atmVclConnKind value of `pvc' and an 3039 atmVclOperStatus with a value other than `up'." 3040 ::= { atm2MIBObjects 21 } 3041 3042atmCurrentlyFailingPVclEntry OBJECT-TYPE 3043 SYNTAX AtmCurrentlyFailingPVclEntry 3044 MAX-ACCESS not-accessible 3045 STATUS current 3046 DESCRIPTION 3047 "Each entry in this table represents a VCL for which the 3048 atmVclRowStatus is `active', the atmVclConnKind is `pvc', and the 3049 atmVclOperStatus is other than `up'." 3050 INDEX { ifIndex, atmVclVpi, atmVclVci } 3051 ::= { atmCurrentlyFailingPVclTable 1 } 3052 3053AtmCurrentlyFailingPVclEntry ::= 3054 SEQUENCE { 3055 atmCurrentlyFailingPVclTimeStamp TimeStamp 3056 } 3057 3058atmCurrentlyFailingPVclTimeStamp OBJECT-TYPE 3059 SYNTAX TimeStamp 3060 MAX-ACCESS read-only 3061 STATUS current 3062 DESCRIPTION 3063 "The time at which this PVCL began to fail." 3064 ::= { atmCurrentlyFailingPVclEntry 1 } 3065 3066 -- ATM PVC Traps 3067 3068 atmPvcTraps OBJECT IDENTIFIER ::= { atm2MIBTraps 1 } 3069 3070 atmPvcTrapsPrefix OBJECT IDENTIFIER ::= { atmPvcTraps 0 } 3071 3072 atmIntfPvcFailuresTrap NOTIFICATION-TYPE 3073 OBJECTS { ifIndex, atmIntfPvcFailures, 3074 atmIntfCurrentlyFailingPVpls, 3075 atmIntfCurrentlyFailingPVcls } 3076 STATUS current 3077 DESCRIPTION 3078 3079 3080 3081 "A notification indicating that one or more PVPLs or PVCLs on 3082 this interface has failed since the last atmPvcFailuresTrap was 3083 sent. If this trap has not been sent for the last 3084 atmIntfPvcNotificationInterval, then it will be sent on the next 3085 increment of atmIntfPvcFailures." 3086 ::= { atmPvcTrapsPrefix 1 } 3087 3088 -- Conformance Information 3089 3090atm2MIBConformance OBJECT IDENTIFIER ::= {atm2MIB 3} 3091 3092atm2MIBGroups OBJECT IDENTIFIER ::= {atm2MIBConformance 1} 3093 3094atm2MIBCompliances OBJECT IDENTIFIER ::= {atm2MIBConformance 2} 3095 3096 -- Compliance Statements 3097 3098atm2MIBCompliance MODULE-COMPLIANCE 3099 STATUS current 3100 DESCRIPTION 3101 "The compliance statement for SNMP entities which represent ATM 3102 interfaces. The compliance statements are used to determine 3103 if a particular group or object applies to hosts, 3104 networks/switches, or both. The Common group is defined as 3105 applicable to all three." 3106 3107 MODULE -- this module 3108 MANDATORY-GROUPS { atmCommonGroup } 3109 3110 -- Objects in the ATM Switch/Service/Host Group 3111 3112 GROUP atmCommonStatsGroup 3113 DESCRIPTION 3114 "This group is mandatory for systems that are supporting 3115 per-VPC or per-VCC counters." 3116 3117 OBJECT atmVplLogicalPortDef 3118 MIN-ACCESS read-only 3119 DESCRIPTION 3120 "This object is mandatory for systems support ATM Logical 3121 Port interfaces." 3122 3123 OBJECT atmIntfSigVccRxTrafficDescrIndex 3124 DESCRIPTION 3125 "This object is mandatory for systems that support negotiation 3126 of signalling VCC traffic parameters through ILMI." 3127 3128 OBJECT atmIntfSigVccTxTrafficDescrIndex 3129 3130 3131 3132 DESCRIPTION 3133 "This object is mandatory for systems that support negotiation 3134 of signalling VCC traffic parameters through ILMI." 3135 3136 OBJECT atmCurrentlyFailingPVplTimeStamp 3137 DESCRIPTION 3138 "This object is optional." 3139 3140 OBJECT atmCurrentlyFailingPVclTimeStamp 3141 DESCRIPTION 3142 "This object is optional." 3143 3144 OBJECT atmIntfLeafSetupFailures 3145 DESCRIPTION 3146 "This object is optional." 3147 3148 OBJECT atmIntfLeafSetupRequests 3149 DESCRIPTION 3150 "This object is optional." 3151 3152 -- Objects in the ATM Switch/Service Group 3153 3154 GROUP atmSwitchServcGroup 3155 DESCRIPTION 3156 "This group is mandatory for a Switch/Service that implements 3157 ATM interfaces." 3158 3159 OBJECT atmIfRegAddrRowStatus 3160 MIN-ACCESS read-only 3161 DESCRIPTION 3162 "Write access is not required, and only one of the six 3163 enumerated values for the RowStatus textual convention need 3164 be supported, specifically: active(1)." 3165 3166 OBJECT atmSvcVpCrossConnectRowStatus 3167 MIN-ACCESS read-only 3168 DESCRIPTION 3169 "Write access is not required, and only one of the six 3170 enumerated values for the RowStatus textual convention need 3171 be supported, specifically: active(1)" 3172 3173 OBJECT atmSvcVcCrossConnectRowStatus 3174 MIN-ACCESS read-only 3175 DESCRIPTION 3176 "Write access is not required, and only one of the six 3177 enumerated values for the RowStatus textual convention need 3178 be supported, specifically: active(1)" 3179 3180 3181 3182 3183 -- Objects in the ATM Switch/Service Signalling Group 3184 3185 GROUP atmSwitchServcSigGroup 3186 DESCRIPTION 3187 "This group's write access is not required." 3188 3189 -- Objects in the ATM Switch/Service Notifications Group 3190 3191 GROUP atmSwitchServcNotifGroup 3192 DESCRIPTION 3193 "This group is optional for systems implementing support for 3194 an ATM Switch or an ATM Network Service." 3195 3196 -- Objects in the ATM Switch Group 3197 3198 GROUP atmSwitchGroup 3199 DESCRIPTION 3200 "This group is optional for a switch that implements ATM 3201 interfaces." 3202 3203 -- Objects in the ATM Service Group 3204 3205 GROUP atmServcGroup 3206 DESCRIPTION 3207 "This group is mandatory for systems implementing support for 3208 an ATM Network Service." 3209 3210 -- Objects in the ATM Host Group 3211 3212 GROUP atmHostGroup 3213 DESCRIPTION 3214 "This group is mandatory for a Host that implements ATM 3215 interfaces." 3216 3217 OBJECT atmVclAddrType 3218 MIN-ACCESS read-only 3219 DESCRIPTION 3220 "Write access is not required." 3221 3222 OBJECT atmVclAddrRowStatus 3223 MIN-ACCESS read-only 3224 DESCRIPTION 3225 "Write access is not required, and only one of the six 3226 enumerated values for the RowStatus textual convention need 3227 be supported, specifically: active(1)." 3228 3229 -- ATM Host Sig Descriptor Parameter Group 3230 3231 3232 3233 3234 GROUP atmHostSigDescrGroup 3235 DESCRIPTION 3236 "This group is mandatory for a Host that implements ATM 3237 interfaces. Write access is not required for this group." 3238 3239 ::= { atm2MIBCompliances 1 } 3240 3241 -- ********************************************** 3242 3243 -- Units of Conformance 3244 -- Mandatory for ATM hosts and switch/service providers 3245 3246atmCommonGroup OBJECT-GROUP 3247 3248OBJECTS { 3249 atmSigSSCOPConEvents, 3250 atmSigSSCOPErrdPdus, 3251 atmSigDetectSetupAttempts, 3252 atmSigEmitSetupAttempts, 3253 atmSigDetectUnavailRoutes, 3254 atmSigEmitUnavailRoutes, 3255 atmSigDetectUnavailResrcs, 3256 atmSigEmitUnavailResrcs, 3257 atmSigDetectCldPtyEvents, 3258 atmSigEmitCldPtyEvents, 3259 atmSigDetectMsgErrors, 3260 atmSigEmitMsgErrors, 3261 atmSigDetectClgPtyEvents, 3262 atmSigEmitClgPtyEvents, 3263 atmSigDetectTimerExpireds, 3264 atmSigEmitTimerExpireds, 3265 atmSigDetectRestarts, 3266 atmSigEmitRestarts, 3267 atmSigInEstabls, 3268 atmSigOutEstabls, 3269 atmVplLogicalPortDef, 3270 atmVplLogicalPortIndex, 3271 atmInterfaceConfMaxSvpcVpi, 3272 atmInterfaceCurrentMaxSvpcVpi, 3273 atmInterfaceConfMaxSvccVpi, 3274 atmInterfaceCurrentMaxSvccVpi, 3275 atmInterfaceConfMinSvccVci, 3276 atmInterfaceCurrentMinSvccVci, 3277 atmIntfSigVccRxTrafficDescrIndex, 3278 atmIntfSigVccTxTrafficDescrIndex, 3279 atmIntfPvcFailures, 3280 atmIntfCurrentlyFailingPVpls, 3281 atmIntfCurrentlyFailingPVcls, 3282 3283 3284 3285 atmIntfPvcNotificationInterval, 3286 atmIntfPvcFailuresTrapEnable, 3287 atmIntfLeafSetupFailures, 3288 atmIntfLeafSetupRequests, 3289 atmIntfConfigType, 3290 atmIntfActualType, 3291 atmIntfConfigSide, 3292 atmIntfActualSide, 3293 atmIntfIlmiAdminStatus, 3294 atmIntfIlmiOperStatus, 3295 atmIntfIlmiFsmState, 3296 atmIntfIlmiEstablishConPollIntvl, 3297 atmIntfIlmiCheckConPollIntvl, 3298 atmIntfIlmiConPollInactFactor, 3299 atmIntfIlmiPublicPrivateIndctr, 3300 atmCurrentlyFailingPVplTimeStamp, 3301 atmCurrentlyFailingPVclTimeStamp 3302} 3303 3304 STATUS current 3305 DESCRIPTION 3306 "A collection of objects providing information 3307 for a Switch/Service/Host that implements 3308 ATM interfaces." 3309 ::= { atm2MIBGroups 1 } 3310 3311atmCommonStatsGroup OBJECT-GROUP 3312 3313OBJECTS { 3314 atmVclStatTotalCellIns, 3315 atmVclStatClp0CellIns, 3316 atmVclStatTotalDiscards, 3317 atmVclStatClp0Discards, 3318 atmVclStatTotalCellOuts, 3319 atmVclStatClp0CellOuts, 3320 atmVclStatClp0Tagged, 3321 atmVplStatTotalCellIns, 3322 atmVplStatClp0CellIns, 3323 atmVplStatTotalDiscards, 3324 atmVplStatClp0Discards, 3325 atmVplStatTotalCellOuts, 3326 atmVplStatClp0CellOuts, 3327 atmVplStatClp0Tagged 3328} 3329 3330 STATUS current 3331 DESCRIPTION 3332 "A collection of objects providing information 3333 3334 3335 3336 for a Switch/Service/Host that implements 3337 ATM VCL and VPL Statistics" 3338 ::= { atm2MIBGroups 2 } 3339 3340 atmSwitchServcGroup OBJECT-GROUP 3341 3342 OBJECTS { 3343 atmIlmiSrvcRegATMAddress, 3344 atmIlmiSrvcRegParm1, 3345 atmIlmiSrvcRegRowStatus, 3346 atmIlmiNetPrefixRowStatus, 3347 atmSvcVpCrossConnectCreationTime, 3348 atmSvcVpCrossConnectRowStatus, 3349 atmSvcVcCrossConnectCreationTime, 3350 atmSvcVcCrossConnectRowStatus, 3351 atmIfRegAddrAddressSource, 3352 atmIfRegAddrOrgScope, 3353 atmIfRegAddrRowStatus} 3354 STATUS current 3355 DESCRIPTION 3356 "A collection of objects providing information 3357 for a Switch/Service that implements ATM interfaces." 3358 ::= { atm2MIBGroups 3 } 3359 3360 atmSwitchServcSigGroup OBJECT-GROUP 3361 3362 OBJECTS { 3363 atmSigSupportClgPtyNumDel, 3364 atmSigSupportClgPtySubAddr, 3365 atmSigSupportCldPtySubAddr, 3366 atmSigSupportHiLyrInfo, 3367 atmSigSupportLoLyrInfo, 3368 atmSigSupportBlliRepeatInd, 3369 atmSigSupportAALInfo, 3370 atmSigSupportPrefCarrier} 3371 STATUS current 3372 DESCRIPTION 3373 "A collection of objects providing information 3374 for a Switch/Service that implements ATM signalling." 3375 ::= { atm2MIBGroups 4 } 3376 3377 atmSwitchServcNotifGroup NOTIFICATION-GROUP 3378 3379 NOTIFICATIONS { atmIntfPvcFailuresTrap } 3380 STATUS current 3381 DESCRIPTION 3382 "A collection of notifications providing information 3383 for a Switch/Service that implements ATM interfaces." 3384 3385 3386 3387 ::= { atm2MIBGroups 5 } 3388 3389 atmSwitchGroup OBJECT-GROUP 3390 OBJECTS { 3391 atmSwitchAddressAddress, 3392 atmSwitchAddressRowStatus } 3393 STATUS current 3394 DESCRIPTION 3395 "A collection of objects providing information 3396 for an ATM switch." 3397 ::= { atm2MIBGroups 6 } 3398 3399 atmServcGroup OBJECT-GROUP 3400 3401 OBJECTS { 3402 atmVpCrossConnectUserName, 3403 atmVpCrossConnectProviderName, 3404 atmVcCrossConnectUserName, 3405 atmVcCrossConnectProviderName } 3406 STATUS current 3407 DESCRIPTION 3408 "A collection of objects providing information 3409 for an ATM Network Service." 3410 ::= { atm2MIBGroups 7 } 3411 3412 atmHostGroup OBJECT-GROUP 3413 3414 OBJECTS { 3415 atmAal5VclInPkts, 3416 atmAal5VclOutPkts, 3417 atmAal5VclInOctets, 3418 atmAal5VclOutOctets, 3419 atmVclAddrType, 3420 atmVclAddrRowStatus, 3421 atmAddrVclAddrType, 3422 atmVclGenSigDescrIndex} 3423 STATUS current 3424 DESCRIPTION 3425 "A collection of objects providing information 3426 for a Host that implements ATM interfaces." 3427 ::= { atm2MIBGroups 8 } 3428 3429 atmHostSigDescrGroup OBJECT-GROUP 3430 3431 OBJECTS { 3432 atmSigDescrParamAalType, 3433 atmSigDescrParamAalSscsType, 3434 atmSigDescrParamBhliType, 3435 3436 3437 3438 atmSigDescrParamBhliInfo, 3439 atmSigDescrParamBbcConnConf, 3440 atmSigDescrParamBlliLayer2, 3441 atmSigDescrParamBlliLayer3, 3442 atmSigDescrParamBlliPktSize, 3443 atmSigDescrParamBlliSnapId, 3444 atmSigDescrParamBlliOuiPid, 3445 atmSigDescrParamRowStatus} 3446 STATUS current 3447 DESCRIPTION 3448 "A collection of objects providing information 3449 for a Host that implements ATM interfaces." 3450 ::= { atm2MIBGroups 9 } 3451 3452END 3453