1-- ***************************************************************** 2-- OLD-CISCO-SYS-MIB.my: Cisco System MIB file 3-- 4-- July 1994, Jeffrey T. Johnson 5-- 6-- Copyright (c) 1994-1996 by cisco Systems, Inc. 7-- All rights reserved. 8-- 9-- ***************************************************************** 10-- 11-- Prior to 10.2, Cisco's lsystem mib group contained a curious 12-- assortment of mib objects. For 10.2, in order to allow similar 13-- objects to be compiled separately with the mib compiler, the 14-- lsystem group was separated into an envmon group (lenv), a cpu 15-- group (lcpu), a memory group (lmem), and a system group (lsystem). 16-- In order to preserve the OBJECT IDENTIFIERS from release 10.1 to 17-- 10.2, however, all four groups are still based at { local 1 }. 18-- This is fine from the mib compiler point-of-view, but causes 19-- problems for some test tools which don't like the fact that 20-- lsystem, lenv, lmem, and lcpu all have the same OBJECT IDENTIFIER. 21-- In order to work around this problem, this file exists which 22-- is a combination of the four 10.2 "system" mibs, with everything 23-- falling under the lsystem group (as it did in 10.1). 24-- 25-- This mib should only be used as a replacement for the four separate 26-- system mibs (OLD-CISCO-CPU.my, OLD-CISCO-ENVMON-MIB.my, 27-- OLD-CISCO-MEMORY-MIB.my, OLD-CISCO-SYSTEM-MIB.my) in test tool 28-- environments. The aforementioned mibs should always be used in 29-- code generation 30 31 OLD-CISCO-SYS-MIB DEFINITIONS ::= BEGIN 32 33 IMPORTS 34 IpAddress 35 FROM RFC1155-SMI 36 OBJECT-TYPE 37 FROM RFC-1212 38 DisplayString 39 FROM RFC1213-MIB 40 local 41 FROM CISCO-SMI; 42 43 lsystem OBJECT IDENTIFIER ::= { local 1 } 44 45 -- Local Variable Section 46 47 -- This section describes the local variables within the cisco 48 -- product line. Groups may or may not be present depending 49 -- on the software options present in the managed device. 50 51 52 -- Local System Group 53 54 -- This group is present in all products. 55 56 romId OBJECT-TYPE 57 SYNTAX DisplayString 58 ACCESS read-only 59 STATUS mandatory 60 DESCRIPTION 61 "This variable contains a printable octet 62 string which contains the System Bootstrap 63 description and version identification." 64 ::= { lsystem 1 } 65 66 whyReload OBJECT-TYPE 67 SYNTAX DisplayString 68 ACCESS read-only 69 STATUS mandatory 70 DESCRIPTION 71 "This variable contains a printable octet 72 string which contains the reason why the 73 system was last restarted." 74 ::= { lsystem 2 } 75 76 hostName OBJECT-TYPE 77 SYNTAX DisplayString 78 ACCESS read-only 79 STATUS mandatory 80 DESCRIPTION 81 "This variable represents the name of the 82 host in printable ascii characters." 83 ::= { lsystem 3 } 84 85 domainName OBJECT-TYPE 86 SYNTAX DisplayString 87 ACCESS read-only 88 STATUS mandatory 89 DESCRIPTION 90 "This variable is the domain portion of the 91 domain name of the host." 92 ::= { lsystem 4 } 93 94 authAddr OBJECT-TYPE 95 SYNTAX IpAddress 96 ACCESS read-only 97 STATUS mandatory 98 DESCRIPTION 99 "This variable contains the last SNMP 100 authorization failure IP address." 101 ::= { lsystem 5 } 102 103 bootHost OBJECT-TYPE 104 SYNTAX IpAddress 105 ACCESS read-only 106 STATUS mandatory 107 DESCRIPTION 108 "Contains the IP address of the host that 109 supplied the currently running software." 110 ::= { lsystem 6 } 111 112 ping OBJECT-TYPE 113 SYNTAX INTEGER 114 ACCESS read-write 115 STATUS obsolete 116 DESCRIPTION 117 "The ping mib object is obsolete as of IOS 10.2 118 It has been superseded by the Cisco Ping MIB" 119 ::= { lsystem 7 } 120 121 freeMem OBJECT-TYPE 122 SYNTAX INTEGER 123 ACCESS read-only 124 STATUS obsolete 125 DESCRIPTION 126 "The freeMem mib object is obsolete as of IOS 11.1 127 It has been replaced with the cisco memory pool mib" 128 ::= { lsystem 8 } 129 130 bufferElFree OBJECT-TYPE 131 SYNTAX INTEGER 132 ACCESS read-only 133 STATUS mandatory 134 DESCRIPTION 135 "Contains the number of free buffer 136 elements." 137 ::= { lsystem 9 } 138 139 bufferElMax OBJECT-TYPE 140 SYNTAX INTEGER 141 ACCESS read-only 142 STATUS mandatory 143 DESCRIPTION 144 "Contains the maximum number of buffer 145 elements." 146 ::= { lsystem 10 } 147 148 bufferElHit OBJECT-TYPE 149 SYNTAX INTEGER 150 ACCESS read-only 151 STATUS mandatory 152 DESCRIPTION 153 "Contains the number of buffer element hits." 154 ::= { lsystem 11 } 155 156 bufferElMiss OBJECT-TYPE 157 SYNTAX INTEGER 158 ACCESS read-only 159 STATUS mandatory 160 DESCRIPTION 161 "Contains the number of buffer element 162 misses." 163 ::= { lsystem 12 } 164 165 bufferElCreate OBJECT-TYPE 166 SYNTAX INTEGER 167 ACCESS read-only 168 STATUS mandatory 169 DESCRIPTION 170 "Contains the number of buffer element 171 creates." 172 ::= { lsystem 13 } 173 174 bufferSmSize OBJECT-TYPE 175 SYNTAX INTEGER 176 ACCESS read-only 177 STATUS mandatory 178 DESCRIPTION 179 "Contains the size of small buffers." 180 ::= { lsystem 14 } 181 182 bufferSmTotal OBJECT-TYPE 183 SYNTAX INTEGER 184 ACCESS read-only 185 STATUS mandatory 186 DESCRIPTION 187 "Contains the total number of small buffers." 188 ::= { lsystem 15 } 189 190 bufferSmFree OBJECT-TYPE 191 SYNTAX INTEGER 192 ACCESS read-only 193 STATUS mandatory 194 DESCRIPTION 195 "Contains the number of free small buffers." 196 ::= { lsystem 16 } 197 198 bufferSmMax OBJECT-TYPE 199 SYNTAX INTEGER 200 ACCESS read-only 201 STATUS mandatory 202 DESCRIPTION 203 "Contains the maximum number of small 204 buffers." 205 ::= { lsystem 17 } 206 207 bufferSmHit OBJECT-TYPE 208 SYNTAX INTEGER 209 ACCESS read-only 210 STATUS mandatory 211 DESCRIPTION 212 "Contains the number of small buffer hits." 213 ::= { lsystem 18 } 214 215 bufferSmMiss OBJECT-TYPE 216 SYNTAX INTEGER 217 ACCESS read-only 218 STATUS mandatory 219 DESCRIPTION 220 "Contains the number of small buffer misses." 221 ::= { lsystem 19 } 222 223 bufferSmTrim OBJECT-TYPE 224 SYNTAX INTEGER 225 ACCESS read-only 226 STATUS mandatory 227 DESCRIPTION 228 "Contains the number of small buffer trims." 229 ::= { lsystem 20 } 230 231 bufferSmCreate OBJECT-TYPE 232 SYNTAX INTEGER 233 ACCESS read-only 234 STATUS mandatory 235 DESCRIPTION 236 "Contains the number of small buffer 237 creates." 238 ::= { lsystem 21 } 239 240 bufferMdSize OBJECT-TYPE 241 SYNTAX INTEGER 242 ACCESS read-only 243 STATUS mandatory 244 DESCRIPTION 245 "Contains the size of medium buffers." 246 ::= { lsystem 22 } 247 248 bufferMdTotal OBJECT-TYPE 249 SYNTAX INTEGER 250 ACCESS read-only 251 STATUS mandatory 252 DESCRIPTION 253 "Contains the total number of medium 254 buffers." 255 ::= { lsystem 23 } 256 257 bufferMdFree OBJECT-TYPE 258 SYNTAX INTEGER 259 ACCESS read-only 260 STATUS mandatory 261 DESCRIPTION 262 "Contains the number of free medium buffers." 263 ::= { lsystem 24 } 264 265 bufferMdMax OBJECT-TYPE 266 SYNTAX INTEGER 267 ACCESS read-only 268 STATUS mandatory 269 DESCRIPTION 270 "Contains the maximum number of medium 271 buffers." 272 ::= { lsystem 25 } 273 274 bufferMdHit OBJECT-TYPE 275 SYNTAX INTEGER 276 ACCESS read-only 277 STATUS mandatory 278 DESCRIPTION 279 "Contains the number of medium buffer hits." 280 ::= { lsystem 26 } 281 282 bufferMdMiss OBJECT-TYPE 283 SYNTAX INTEGER 284 ACCESS read-only 285 STATUS mandatory 286 DESCRIPTION 287 "Contains the number of medium buffer 288 misses." 289 ::= { lsystem 27 } 290 291 bufferMdTrim OBJECT-TYPE 292 SYNTAX INTEGER 293 ACCESS read-only 294 STATUS mandatory 295 DESCRIPTION 296 "Contains the number of medium buffer trims." 297 ::= { lsystem 28 } 298 299 bufferMdCreate OBJECT-TYPE 300 SYNTAX INTEGER 301 ACCESS read-only 302 STATUS mandatory 303 DESCRIPTION 304 "Contains the number of medium buffer 305 creates." 306 ::= { lsystem 29 } 307 308 bufferBgSize OBJECT-TYPE 309 SYNTAX INTEGER 310 ACCESS read-only 311 STATUS mandatory 312 DESCRIPTION 313 "Contains the size of big buffers." 314 ::= { lsystem 30 } 315 316 bufferBgTotal OBJECT-TYPE 317 SYNTAX INTEGER 318 ACCESS read-only 319 STATUS mandatory 320 DESCRIPTION 321 "Contains the total number of big buffers." 322 ::= { lsystem 31 } 323 324 bufferBgFree OBJECT-TYPE 325 SYNTAX INTEGER 326 ACCESS read-only 327 STATUS mandatory 328 DESCRIPTION 329 "Contains the number of free big buffers." 330 ::= { lsystem 32 } 331 332 bufferBgMax OBJECT-TYPE 333 SYNTAX INTEGER 334 ACCESS read-only 335 STATUS mandatory 336 DESCRIPTION 337 "Contains the maximum number of big buffers." 338 ::= { lsystem 33 } 339 340 bufferBgHit OBJECT-TYPE 341 SYNTAX INTEGER 342 ACCESS read-only 343 STATUS mandatory 344 DESCRIPTION 345 "Contains the number of big buffer hits." 346 ::= { lsystem 34 } 347 348 bufferBgMiss OBJECT-TYPE 349 SYNTAX INTEGER 350 ACCESS read-only 351 STATUS mandatory 352 DESCRIPTION 353 "Contains the number of big buffer misses." 354 ::= { lsystem 35 } 355 356 bufferBgTrim OBJECT-TYPE 357 SYNTAX INTEGER 358 ACCESS read-only 359 STATUS mandatory 360 DESCRIPTION 361 "Contains the number of big buffer trims." 362 ::= { lsystem 36 } 363 364 bufferBgCreate OBJECT-TYPE 365 SYNTAX INTEGER 366 ACCESS read-only 367 STATUS mandatory 368 DESCRIPTION 369 "Contains the number of big buffer creates." 370 ::= { lsystem 37 } 371 372 bufferLgSize OBJECT-TYPE 373 SYNTAX INTEGER 374 ACCESS read-only 375 STATUS mandatory 376 DESCRIPTION 377 "Contains the size of large buffers." 378 ::= { lsystem 38 } 379 380 bufferLgTotal OBJECT-TYPE 381 SYNTAX INTEGER 382 ACCESS read-only 383 STATUS mandatory 384 DESCRIPTION 385 "Contains the total number of large buffers." 386 ::= { lsystem 39 } 387 388 bufferLgFree OBJECT-TYPE 389 SYNTAX INTEGER 390 ACCESS read-only 391 STATUS mandatory 392 DESCRIPTION 393 "Contains the number of free large buffers." 394 ::= { lsystem 40 } 395 396 bufferLgMax OBJECT-TYPE 397 SYNTAX INTEGER 398 ACCESS read-only 399 STATUS mandatory 400 DESCRIPTION 401 "Contains the maximum number of large 402 buffers." 403 ::= { lsystem 41 } 404 405 bufferLgHit OBJECT-TYPE 406 SYNTAX INTEGER 407 ACCESS read-only 408 STATUS mandatory 409 DESCRIPTION 410 "Contains the number of large buffer hits." 411 ::= { lsystem 42 } 412 413 bufferLgMiss OBJECT-TYPE 414 SYNTAX INTEGER 415 ACCESS read-only 416 STATUS mandatory 417 DESCRIPTION 418 "Contains the number of large buffer misses." 419 ::= { lsystem 43 } 420 421 bufferLgTrim OBJECT-TYPE 422 SYNTAX INTEGER 423 ACCESS read-only 424 STATUS mandatory 425 DESCRIPTION 426 "Contains the number of large buffer trims." 427 ::= { lsystem 44 } 428 429 bufferLgCreate OBJECT-TYPE 430 SYNTAX INTEGER 431 ACCESS read-only 432 STATUS mandatory 433 DESCRIPTION 434 "Contains the number of large buffer 435 creates." 436 ::= { lsystem 45 } 437 438 bufferFail OBJECT-TYPE 439 SYNTAX INTEGER 440 ACCESS read-only 441 STATUS mandatory 442 DESCRIPTION 443 "Count of the number of buffer allocation 444 failures." 445 ::= { lsystem 46 } 446 447 bufferNoMem OBJECT-TYPE 448 SYNTAX INTEGER 449 ACCESS read-only 450 STATUS mandatory 451 DESCRIPTION 452 "Count of the number of buffer create 453 failures due to no free memory." 454 ::= { lsystem 47 } 455 456 netConfigAddr OBJECT-TYPE 457 SYNTAX IpAddress 458 ACCESS read-only 459 STATUS mandatory 460 DESCRIPTION 461 "Holds the address of the host that supplied 462 the network-confg file." 463 ::= { lsystem 48 } 464 465 netConfigName OBJECT-TYPE 466 SYNTAX DisplayString 467 ACCESS read-only 468 STATUS mandatory 469 DESCRIPTION 470 "Holds the name of the network configuration 471 file." 472 ::= { lsystem 49 } 473 474 netConfigSet OBJECT-TYPE 475 SYNTAX DisplayString 476 ACCESS write-only 477 STATUS mandatory 478 DESCRIPTION 479 "Cause the loading of a new network-confg 480 file using TFTP." 481 ::= { lsystem 50 } 482 483 hostConfigAddr OBJECT-TYPE 484 SYNTAX IpAddress 485 ACCESS read-only 486 STATUS obsolete 487 DESCRIPTION 488 "Contains the address of the host that 489 provided the host-config file." 490 ::= { lsystem 51 } 491 492 hostConfigName OBJECT-TYPE 493 SYNTAX DisplayString 494 ACCESS read-only 495 STATUS obsolete 496 DESCRIPTION 497 "Contains the name of the last configured 498 host-confg file." 499 ::= { lsystem 52 } 500 501 hostConfigSet OBJECT-TYPE 502 SYNTAX DisplayString 503 ACCESS write-only 504 STATUS obsolete 505 DESCRIPTION 506 "Cause the loading of a new host-confg file 507 using TFTP." 508 ::= { lsystem 53 } 509 510 writeMem OBJECT-TYPE 511 SYNTAX INTEGER 512 ACCESS write-only 513 STATUS mandatory 514 DESCRIPTION 515 "Write configuration into non-volatile memory 516 / erase config memory if 0." 517 ::= { lsystem 54 } 518 519 writeNet OBJECT-TYPE 520 SYNTAX DisplayString 521 ACCESS write-only 522 STATUS mandatory 523 DESCRIPTION 524 "Write configuration to host using TFTP." 525 ::= { lsystem 55 } 526 527 busyPer OBJECT-TYPE 528 SYNTAX INTEGER 529 ACCESS read-only 530 STATUS mandatory 531 DESCRIPTION 532 "CPU busy percentage in the last 5 second 533 period. Not the last 5 realtime seconds but 534 the last 5 second period in the scheduler." 535 ::= { lsystem 56 } 536 537 avgBusy1 OBJECT-TYPE 538 SYNTAX INTEGER 539 ACCESS read-only 540 STATUS mandatory 541 DESCRIPTION 542 "1 minute exponentially-decayed moving 543 average of the CPU busy percentage." 544 ::= { lsystem 57 } 545 546 avgBusy5 OBJECT-TYPE 547 SYNTAX INTEGER 548 ACCESS read-only 549 STATUS mandatory 550 DESCRIPTION 551 "5 minute exponentially-decayed moving 552 average of the CPU busy percentage." 553 ::= { lsystem 58 } 554 555 idleCount OBJECT-TYPE 556 SYNTAX INTEGER 557 ACCESS read-write 558 STATUS mandatory 559 DESCRIPTION 560 "cisco internal variable. not to be used" 561 ::= { lsystem 59 } 562 563 idleWired OBJECT-TYPE 564 SYNTAX INTEGER 565 ACCESS read-write 566 STATUS mandatory 567 DESCRIPTION 568 "cisco internal variable. not to be used" 569 ::= { lsystem 60 } 570 571 ciscoContactInfo OBJECT-TYPE 572 SYNTAX DisplayString 573 ACCESS read-only 574 STATUS mandatory 575 DESCRIPTION 576 "cisco's name and address" 577 ::= { lsystem 61 } 578 579 bufferHgSize OBJECT-TYPE 580 SYNTAX INTEGER 581 ACCESS read-only 582 STATUS mandatory 583 DESCRIPTION 584 "Contains the size of huge buffers." 585 ::= { lsystem 62 } 586 587 bufferHgTotal OBJECT-TYPE 588 SYNTAX INTEGER 589 ACCESS read-only 590 STATUS mandatory 591 DESCRIPTION 592 "Contains the total number of huge buffers." 593 ::= { lsystem 63 } 594 595 bufferHgFree OBJECT-TYPE 596 SYNTAX INTEGER 597 ACCESS read-only 598 STATUS mandatory 599 DESCRIPTION 600 "Contains the number of free huge buffers." 601 ::= { lsystem 64 } 602 603 bufferHgMax OBJECT-TYPE 604 SYNTAX INTEGER 605 ACCESS read-only 606 STATUS mandatory 607 DESCRIPTION 608 "Contains the maximum number of huge 609 buffers." 610 ::= { lsystem 65 } 611 612 bufferHgHit OBJECT-TYPE 613 SYNTAX INTEGER 614 ACCESS read-only 615 STATUS mandatory 616 DESCRIPTION 617 "Contains the number of huge buffer hits." 618 ::= { lsystem 66 } 619 620 bufferHgMiss OBJECT-TYPE 621 SYNTAX INTEGER 622 ACCESS read-only 623 STATUS mandatory 624 DESCRIPTION 625 "Contains the number of huge buffer misses." 626 ::= { lsystem 67 } 627 628 bufferHgTrim OBJECT-TYPE 629 SYNTAX INTEGER 630 ACCESS read-only 631 STATUS mandatory 632 DESCRIPTION 633 "Contains the number of huge buffer trims." 634 ::= { lsystem 68 } 635 636 bufferHgCreate OBJECT-TYPE 637 SYNTAX INTEGER 638 ACCESS read-only 639 STATUS mandatory 640 DESCRIPTION 641 "Contains the number of huge buffer creates." 642 ::= { lsystem 69 } 643 644 netConfigProto OBJECT-TYPE 645 SYNTAX INTEGER 646 ACCESS read-only 647 STATUS mandatory 648 DESCRIPTION 649 "Holds the protocol that supplied the 650 network-confg file." 651 ::= { lsystem 70 } 652 653 hostConfigProto OBJECT-TYPE 654 SYNTAX INTEGER 655 ACCESS read-only 656 STATUS mandatory 657 DESCRIPTION 658 "Holds the protocol that supplied the host- 659 confg file." 660 ::= { lsystem 71 } 661 662 sysConfigAddr OBJECT-TYPE 663 SYNTAX IpAddress 664 ACCESS read-only 665 STATUS mandatory 666 DESCRIPTION 667 "Holds the address of the host that supplied 668 the system boot image." 669 ::= { lsystem 72 } 670 671 sysConfigName OBJECT-TYPE 672 SYNTAX DisplayString 673 ACCESS read-only 674 STATUS mandatory 675 DESCRIPTION 676 "Holds the name of the system boot image." 677 ::= { lsystem 73 } 678 679 sysConfigProto OBJECT-TYPE 680 SYNTAX INTEGER 681 ACCESS read-only 682 STATUS mandatory 683 DESCRIPTION 684 "Holds the protocol that supplied the system 685 boot image." 686 ::= { lsystem 74 } 687 688 sysClearARP OBJECT-TYPE 689 SYNTAX INTEGER 690 ACCESS write-only 691 STATUS mandatory 692 DESCRIPTION 693 "Perform a clearing of the entire ARP cache 694 and invalidation of route caches." 695 ::= { lsystem 75 } 696 697 sysClearInt OBJECT-TYPE 698 SYNTAX INTEGER 699 ACCESS write-only 700 STATUS mandatory 701 DESCRIPTION 702 "Clear interface given IfIndex as value." 703 ::= { lsystem 76 } 704 705 envPresent OBJECT-TYPE 706 SYNTAX INTEGER 707 ACCESS read-only 708 STATUS mandatory 709 DESCRIPTION 710 "Is there an environmental monitor card in 711 this box?, 0 - No, 1-AGS card present, wrong 712 firmware, 2-AGS CARD present, firmware ok, 713 3-7000 support" 714 ::= { lsystem 77 } 715 716 envTestPt1Descr OBJECT-TYPE 717 SYNTAX DisplayString 718 ACCESS read-only 719 STATUS mandatory 720 DESCRIPTION 721 "Description of the test point 1. Typically 722 ambient air or the temperature of air 723 entering the router" 724 ::= { lsystem 78 } 725 726 envTestPt1Measure OBJECT-TYPE 727 SYNTAX INTEGER 728 ACCESS read-only 729 STATUS mandatory 730 DESCRIPTION 731 "Current value of test point 1. Typically a 732 temperature in centigrade." 733 ::= { lsystem 79 } 734 735 envTestPt2Descr OBJECT-TYPE 736 SYNTAX DisplayString 737 ACCESS read-only 738 STATUS mandatory 739 DESCRIPTION 740 "Description of the test point 2. Typically 741 airflow or the temperature of air leaving the 742 router" 743 ::= { lsystem 80 } 744 745 envTestPt2Measure OBJECT-TYPE 746 SYNTAX INTEGER 747 ACCESS read-only 748 STATUS mandatory 749 DESCRIPTION 750 "Current value of test point 2. Typically a 751 temperature in centigrade." 752 ::= { lsystem 81 } 753 754 envTestPt3Descr OBJECT-TYPE 755 SYNTAX DisplayString 756 ACCESS read-only 757 STATUS mandatory 758 DESCRIPTION 759 "Description of the test point 3. Typically 760 +5 volt" 761 ::= { lsystem 82 } 762 763 envTestPt3Measure OBJECT-TYPE 764 SYNTAX INTEGER 765 ACCESS read-only 766 STATUS mandatory 767 DESCRIPTION 768 "Current value of test point 3. Typically the 769 value in millivolts of the +5v supply" 770 ::= { lsystem 83 } 771 772 envTestPt4Descr OBJECT-TYPE 773 SYNTAX DisplayString 774 ACCESS read-only 775 STATUS mandatory 776 DESCRIPTION 777 "Description of the test point 4. Typically 778 +12 volt" 779 ::= { lsystem 84 } 780 781 envTestPt4Measure OBJECT-TYPE 782 SYNTAX INTEGER 783 ACCESS read-only 784 STATUS mandatory 785 DESCRIPTION 786 "Current value of test point 4. Typically the 787 value in millivolts of the +12v supply" 788 ::= { lsystem 85 } 789 790 envTestPt5Descr OBJECT-TYPE 791 SYNTAX DisplayString 792 ACCESS read-only 793 STATUS mandatory 794 DESCRIPTION 795 "Description of the test point 5. Typically 796 -12 volt" 797 ::= { lsystem 86 } 798 799 envTestPt5Measure OBJECT-TYPE 800 SYNTAX INTEGER 801 ACCESS read-only 802 STATUS mandatory 803 DESCRIPTION 804 "Current value of test point 5. Typically the 805 value in millivolts of the -12v supply" 806 ::= { lsystem 87 } 807 808 envTestPt6Descr OBJECT-TYPE 809 SYNTAX DisplayString 810 ACCESS read-only 811 STATUS mandatory 812 DESCRIPTION 813 "Description of the test point 6. Typically 814 -5 volt" 815 ::= { lsystem 88 } 816 817 envTestPt6Measure OBJECT-TYPE 818 SYNTAX INTEGER 819 ACCESS read-only 820 STATUS mandatory 821 DESCRIPTION 822 "Current value of test point 6. Typically the 823 value in millivolts of the -5v supply" 824 ::= { lsystem 89 } 825 826 envTestPt1MarginVal OBJECT-TYPE 827 SYNTAX INTEGER 828 ACCESS read-only 829 STATUS mandatory 830 DESCRIPTION 831 "Value at which the router will shutdown. 832 Typically the ambient air temperature that 833 will shut the router down. (e.g. 43)" 834 ::= { lsystem 90 } 835 836 envTestPt2MarginVal OBJECT-TYPE 837 SYNTAX INTEGER 838 ACCESS read-only 839 STATUS mandatory 840 DESCRIPTION 841 "Value at which the router will shutdown. 842 Typically the airflow air temperature that 843 will shut the router down. (e.g. 58)" 844 ::= { lsystem 91 } 845 846 envTestPt3MarginPercent OBJECT-TYPE 847 SYNTAX INTEGER 848 ACCESS read-only 849 STATUS mandatory 850 DESCRIPTION 851 "+/- Percentage that will shut the router 852 down, (e.g. 10%) typically +5 volt" 853 ::= { lsystem 92 } 854 855 envTestPt4MarginPercent OBJECT-TYPE 856 SYNTAX INTEGER 857 ACCESS read-only 858 STATUS mandatory 859 DESCRIPTION 860 "+/- Percentage that will shut the router 861 down, (e.g. 15%) typically +12 volt" 862 ::= { lsystem 93 } 863 864 envTestPt5MarginPercent OBJECT-TYPE 865 SYNTAX INTEGER 866 ACCESS read-only 867 STATUS mandatory 868 DESCRIPTION 869 "+/- Percentage that will shut the router 870 down, (e.g. 15%) typically -12 volt" 871 ::= { lsystem 94 } 872 873 envTestPt6MarginPercent OBJECT-TYPE 874 SYNTAX INTEGER 875 ACCESS read-only 876 STATUS mandatory 877 DESCRIPTION 878 "+/- Percentage that will shut the router 879 down, (e.g. 10%) typically -5 volt" 880 ::= { lsystem 95 } 881 882 envTestPt1last OBJECT-TYPE 883 SYNTAX INTEGER 884 ACCESS read-only 885 STATUS mandatory 886 DESCRIPTION 887 "Value of TestPt1 when last shutdown 888 occurred." 889 ::= { lsystem 96 } 890 891 envTestPt2last OBJECT-TYPE 892 SYNTAX INTEGER 893 ACCESS read-only 894 STATUS mandatory 895 DESCRIPTION 896 "Value of TestPt2 when last shutdown 897 occurred." 898 ::= { lsystem 97 } 899 900 envTestPt3last OBJECT-TYPE 901 SYNTAX INTEGER 902 ACCESS read-only 903 STATUS mandatory 904 DESCRIPTION 905 "Value of TestPt3 when last shutdown 906 occurred." 907 ::= { lsystem 98 } 908 909 envTestPt4last OBJECT-TYPE 910 SYNTAX INTEGER 911 ACCESS read-only 912 STATUS mandatory 913 DESCRIPTION 914 "Value of TestPt4 when last shutdown 915 occurred." 916 ::= { lsystem 99 } 917 918 envTestPt5last OBJECT-TYPE 919 SYNTAX INTEGER 920 ACCESS read-only 921 STATUS mandatory 922 DESCRIPTION 923 "Value of TestPt5 when last shutdown 924 occurred." 925 ::= { lsystem 100 } 926 927 envTestPt6last OBJECT-TYPE 928 SYNTAX INTEGER 929 ACCESS read-only 930 STATUS mandatory 931 DESCRIPTION 932 "Value of TestPt6 when last shutdown 933 occurred." 934 ::= { lsystem 101 } 935 936 envTestPt1warn OBJECT-TYPE 937 SYNTAX INTEGER { 938 warning(1), 939 noWarning(2) 940 } 941 ACCESS read-only 942 STATUS mandatory 943 DESCRIPTION 944 "Is this test point at a warning level?" 945 ::= { lsystem 102 } 946 947 envTestPt2warn OBJECT-TYPE 948 SYNTAX INTEGER { 949 warning(1), 950 noWarning(2) 951 } 952 ACCESS read-only 953 STATUS mandatory 954 DESCRIPTION 955 "Is this test point at a warning level?" 956 ::= { lsystem 103 } 957 958 envTestPt3warn OBJECT-TYPE 959 SYNTAX INTEGER { 960 warning(1), 961 noWarning(2) 962 } 963 ACCESS read-only 964 STATUS mandatory 965 DESCRIPTION 966 "Is this test point at a warning level?" 967 ::= { lsystem 104 } 968 969 envTestPt4warn OBJECT-TYPE 970 SYNTAX INTEGER { 971 warning(1), 972 noWarning(2) 973 } 974 ACCESS read-only 975 STATUS mandatory 976 DESCRIPTION 977 "Is this test point at a warning level?" 978 ::= { lsystem 105 } 979 980 envTestPt5warn OBJECT-TYPE 981 SYNTAX INTEGER { 982 warning(1), 983 noWarning(2) 984 } 985 ACCESS read-only 986 STATUS mandatory 987 DESCRIPTION 988 "Is this test point at a warning level?" 989 ::= { lsystem 106 } 990 991 envTestPt6warn OBJECT-TYPE 992 SYNTAX INTEGER { 993 warning(1), 994 noWarning(2) 995 } 996 ACCESS read-only 997 STATUS mandatory 998 DESCRIPTION 999 "Is this test point at a warning level?" 1000 ::= { lsystem 107 } 1001 1002 envFirmVersion OBJECT-TYPE 1003 SYNTAX DisplayString 1004 ACCESS read-only 1005 STATUS mandatory 1006 DESCRIPTION 1007 "Description of Environmental Card firmware" 1008 ::= { lsystem 108 } 1009 1010 envTechnicianID OBJECT-TYPE 1011 SYNTAX DisplayString 1012 ACCESS read-only 1013 STATUS mandatory 1014 DESCRIPTION 1015 "Technician ID" 1016 ::= { lsystem 109 } 1017 1018 envType OBJECT-TYPE 1019 SYNTAX DisplayString 1020 ACCESS read-only 1021 STATUS mandatory 1022 DESCRIPTION 1023 "The type of environmental card" 1024 ::= { lsystem 110 } 1025 1026 envBurnDate OBJECT-TYPE 1027 SYNTAX DisplayString 1028 ACCESS read-only 1029 STATUS mandatory 1030 DESCRIPTION 1031 "The calibration / burn in date" 1032 ::= { lsystem 111 } 1033 1034 envSerialNumber OBJECT-TYPE 1035 SYNTAX DisplayString 1036 ACCESS read-only 1037 STATUS mandatory 1038 DESCRIPTION 1039 "Serial Number of environmental monitor card" 1040 ::= { lsystem 112 } 1041 1042 1043 END 1044