1// SPDX-License-Identifier: GPL-2.0-only 2/* 3 * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com/ 4 */ 5#include "omap5.dtsi" 6#include <dt-bindings/interrupt-controller/irq.h> 7#include <dt-bindings/interrupt-controller/arm-gic.h> 8 9/ { 10 aliases { 11 display0 = &hdmi0; 12 }; 13 14 chosen { 15 stdout-path = &uart3; 16 }; 17 18 vmain: fixedregulator-vmain { 19 compatible = "regulator-fixed"; 20 regulator-name = "vmain"; 21 regulator-min-microvolt = <5000000>; 22 regulator-max-microvolt = <5000000>; 23 }; 24 25 vsys_cobra: fixedregulator-vsys_cobra { 26 compatible = "regulator-fixed"; 27 regulator-name = "vsys_cobra"; 28 vin-supply = <&vmain>; 29 regulator-min-microvolt = <5000000>; 30 regulator-max-microvolt = <5000000>; 31 }; 32 33 vdds_1v8_main: fixedregulator-vdds_1v8_main { 34 compatible = "regulator-fixed"; 35 regulator-name = "vdds_1v8_main"; 36 vin-supply = <&smps7_reg>; 37 regulator-min-microvolt = <1800000>; 38 regulator-max-microvolt = <1800000>; 39 }; 40 41 vmmcsd_fixed: fixedregulator-mmcsd { 42 compatible = "regulator-fixed"; 43 regulator-name = "vmmcsd_fixed"; 44 regulator-min-microvolt = <3000000>; 45 regulator-max-microvolt = <3000000>; 46 }; 47 48 mmc3_pwrseq: sdhci0_pwrseq { 49 compatible = "mmc-pwrseq-simple"; 50 clocks = <&clk32kgaudio>; 51 clock-names = "ext_clock"; 52 }; 53 54 vmmcsdio_fixed: fixedregulator-mmcsdio { 55 compatible = "regulator-fixed"; 56 regulator-name = "vmmcsdio_fixed"; 57 regulator-min-microvolt = <1800000>; 58 regulator-max-microvolt = <1800000>; 59 gpio = <&gpio5 12 GPIO_ACTIVE_HIGH>; /* gpio140 WLAN_EN */ 60 enable-active-high; 61 startup-delay-us = <70000>; 62 pinctrl-names = "default"; 63 pinctrl-0 = <&wlan_pins>; 64 }; 65 66 /* HS USB Host PHY on PORT 2 */ 67 hsusb2_phy: hsusb2_phy { 68 compatible = "usb-nop-xceiv"; 69 reset-gpios = <&gpio3 16 GPIO_ACTIVE_LOW>; /* gpio3_80 HUB_NRESET */ 70 clocks = <&auxclk1_ck>; 71 clock-names = "main_clk"; 72 clock-frequency = <19200000>; 73 #phy-cells = <0>; 74 }; 75 76 /* HS USB Host PHY on PORT 3 */ 77 hsusb3_phy: hsusb3_phy { 78 compatible = "usb-nop-xceiv"; 79 reset-gpios = <&gpio3 15 GPIO_ACTIVE_LOW>; /* gpio3_79 ETH_NRESET */ 80 #phy-cells = <0>; 81 }; 82 83 tpd12s015: encoder { 84 compatible = "ti,tpd12s015"; 85 86 pinctrl-names = "default"; 87 pinctrl-0 = <&tpd12s015_pins>; 88 89 /* gpios defined in the board specific dts */ 90 91 ports { 92 #address-cells = <1>; 93 #size-cells = <0>; 94 95 port@0 { 96 reg = <0>; 97 98 tpd12s015_in: endpoint { 99 remote-endpoint = <&hdmi_out>; 100 }; 101 }; 102 103 port@1 { 104 reg = <1>; 105 106 tpd12s015_out: endpoint { 107 remote-endpoint = <&hdmi_connector_in>; 108 }; 109 }; 110 }; 111 }; 112 113 hdmi0: connector { 114 compatible = "hdmi-connector"; 115 label = "hdmi"; 116 117 type = "b"; 118 119 port { 120 hdmi_connector_in: endpoint { 121 remote-endpoint = <&tpd12s015_out>; 122 }; 123 }; 124 }; 125 126 sound: sound { 127 compatible = "ti,abe-twl6040"; 128 ti,model = "omap5-uevm"; 129 130 ti,jack-detection; 131 ti,mclk-freq = <19200000>; 132 133 ti,mcpdm = <&mcpdm>; 134 135 ti,twl6040 = <&twl6040>; 136 137 /* Audio routing */ 138 ti,audio-routing = 139 "Headset Stereophone", "HSOL", 140 "Headset Stereophone", "HSOR", 141 "Line Out", "AUXL", 142 "Line Out", "AUXR", 143 "HSMIC", "Headset Mic", 144 "Headset Mic", "Headset Mic Bias", 145 "AFML", "Line In", 146 "AFMR", "Line In"; 147 }; 148}; 149 150&gpio8 { 151 /* TI trees use GPIO instead of msecure, see also muxing */ 152 p234 { 153 gpio-hog; 154 gpios = <10 GPIO_ACTIVE_HIGH>; 155 output-high; 156 line-name = "gpio8_234/msecure"; 157 }; 158}; 159 160&omap5_pmx_core { 161 pinctrl-names = "default"; 162 pinctrl-0 = < 163 &usbhost_pins 164 &led_gpio_pins 165 >; 166 167 twl6040_pins: pinmux_twl6040_pins { 168 pinctrl-single,pins = < 169 OMAP5_IOPAD(0x1be, PIN_OUTPUT | MUX_MODE6) /* mcspi1_somi.gpio5_141 */ 170 >; 171 }; 172 173 mcpdm_pins: pinmux_mcpdm_pins { 174 pinctrl-single,pins = < 175 OMAP5_IOPAD(0x182, PIN_INPUT_PULLDOWN | MUX_MODE0) /* abe_clks.abe_clks */ 176 OMAP5_IOPAD(0x19c, PIN_INPUT_PULLDOWN | MUX_MODE0) /* abemcpdm_ul_data.abemcpdm_ul_data */ 177 OMAP5_IOPAD(0x19e, PIN_INPUT_PULLDOWN | MUX_MODE0) /* abemcpdm_dl_data.abemcpdm_dl_data */ 178 OMAP5_IOPAD(0x1a0, PIN_INPUT_PULLUP | MUX_MODE0) /* abemcpdm_frame.abemcpdm_frame */ 179 OMAP5_IOPAD(0x1a2, PIN_INPUT_PULLDOWN | MUX_MODE0) /* abemcpdm_lb_clk.abemcpdm_lb_clk */ 180 >; 181 }; 182 183 mcbsp1_pins: pinmux_mcbsp1_pins { 184 pinctrl-single,pins = < 185 OMAP5_IOPAD(0x18c, PIN_INPUT | MUX_MODE1) /* abedmic_clk2.abemcbsp1_fsx */ 186 OMAP5_IOPAD(0x18e, PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* abedmic_clk3.abemcbsp1_dx */ 187 OMAP5_IOPAD(0x190, PIN_INPUT | MUX_MODE1) /* abeslimbus1_clock.abemcbsp1_clkx */ 188 OMAP5_IOPAD(0x192, PIN_INPUT_PULLDOWN | MUX_MODE1) /* abeslimbus1_data.abemcbsp1_dr */ 189 >; 190 }; 191 192 mcbsp2_pins: pinmux_mcbsp2_pins { 193 pinctrl-single,pins = < 194 OMAP5_IOPAD(0x194, PIN_INPUT_PULLDOWN | MUX_MODE0) /* abemcbsp2_dr.abemcbsp2_dr */ 195 OMAP5_IOPAD(0x196, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* abemcbsp2_dx.abemcbsp2_dx */ 196 OMAP5_IOPAD(0x198, PIN_INPUT | MUX_MODE0) /* abemcbsp2_fsx.abemcbsp2_fsx */ 197 OMAP5_IOPAD(0x19a, PIN_INPUT | MUX_MODE0) /* abemcbsp2_clkx.abemcbsp2_clkx */ 198 >; 199 }; 200 201 i2c1_pins: pinmux_i2c1_pins { 202 pinctrl-single,pins = < 203 OMAP5_IOPAD(0x1f2, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_scl */ 204 OMAP5_IOPAD(0x1f4, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_sda */ 205 >; 206 }; 207 208 mcspi2_pins: pinmux_mcspi2_pins { 209 pinctrl-single,pins = < 210 OMAP5_IOPAD(0x0fc, PIN_INPUT | MUX_MODE0) /* mcspi2_clk */ 211 OMAP5_IOPAD(0x0fe, PIN_INPUT | MUX_MODE0) /* mcspi2_simo */ 212 OMAP5_IOPAD(0x100, PIN_INPUT_PULLUP | MUX_MODE0) /* mcspi2_somi */ 213 OMAP5_IOPAD(0x102, PIN_OUTPUT | MUX_MODE0) /* mcspi2_cs0 */ 214 >; 215 }; 216 217 mcspi3_pins: pinmux_mcspi3_pins { 218 pinctrl-single,pins = < 219 OMAP5_IOPAD(0x0b8, PIN_INPUT | MUX_MODE1) /* mcspi3_somi */ 220 OMAP5_IOPAD(0x0ba, PIN_INPUT | MUX_MODE1) /* mcspi3_cs0 */ 221 OMAP5_IOPAD(0x0bc, PIN_INPUT | MUX_MODE1) /* mcspi3_simo */ 222 OMAP5_IOPAD(0x0be, PIN_INPUT | MUX_MODE1) /* mcspi3_clk */ 223 >; 224 }; 225 226 mmc3_pins: pinmux_mmc3_pins { 227 pinctrl-single,pins = < 228 OMAP5_IOPAD(0x01a4, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_clk */ 229 OMAP5_IOPAD(0x01a6, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_cmd */ 230 OMAP5_IOPAD(0x01a8, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_data0 */ 231 OMAP5_IOPAD(0x01aa, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_data1 */ 232 OMAP5_IOPAD(0x01ac, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_data2 */ 233 OMAP5_IOPAD(0x01ae, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_data3 */ 234 >; 235 }; 236 237 wlan_pins: pinmux_wlan_pins { 238 pinctrl-single,pins = < 239 OMAP5_IOPAD(0x1bc, PIN_OUTPUT | MUX_MODE6) /* mcspi1_clk.gpio5_140 */ 240 >; 241 }; 242 243 /* TI trees use GPIO mode; msecure mode does not work reliably? */ 244 palmas_msecure_pins: palmas_msecure_pins { 245 pinctrl-single,pins = < 246 OMAP5_IOPAD(0x180, PIN_OUTPUT | MUX_MODE6) /* gpio8_234 */ 247 >; 248 }; 249 250 usbhost_pins: pinmux_usbhost_pins { 251 pinctrl-single,pins = < 252 OMAP5_IOPAD(0x0c4, PIN_INPUT | MUX_MODE0) /* usbb2_hsic_strobe */ 253 OMAP5_IOPAD(0x0c6, PIN_INPUT | MUX_MODE0) /* usbb2_hsic_data */ 254 255 OMAP5_IOPAD(0x1de, PIN_INPUT | MUX_MODE0) /* usbb3_hsic_strobe */ 256 OMAP5_IOPAD(0x1e0, PIN_INPUT | MUX_MODE0) /* usbb3_hsic_data */ 257 258 OMAP5_IOPAD(0x0b0, PIN_OUTPUT | MUX_MODE6) /* gpio3_80 HUB_NRESET */ 259 OMAP5_IOPAD(0x0ae, PIN_OUTPUT | MUX_MODE6) /* gpio3_79 ETH_NRESET */ 260 >; 261 }; 262 263 led_gpio_pins: pinmux_led_gpio_pins { 264 pinctrl-single,pins = < 265 OMAP5_IOPAD(0x1d6, PIN_OUTPUT | MUX_MODE6) /* uart3_cts_rctx.gpio5_153 */ 266 >; 267 }; 268 269 uart1_pins: pinmux_uart1_pins { 270 pinctrl-single,pins = < 271 OMAP5_IOPAD(0x0a0, PIN_OUTPUT | MUX_MODE0) /* uart1_tx.uart1_cts */ 272 OMAP5_IOPAD(0x0a2, PIN_INPUT_PULLUP | MUX_MODE0) /* uart1_tx.uart1_cts */ 273 OMAP5_IOPAD(0x0a4, PIN_INPUT_PULLUP | MUX_MODE0) /* uart1_rx.uart1_rts */ 274 OMAP5_IOPAD(0x0a6, PIN_OUTPUT | MUX_MODE0) /* uart1_rx.uart1_rts */ 275 >; 276 }; 277 278 uart3_pins: pinmux_uart3_pins { 279 pinctrl-single,pins = < 280 OMAP5_IOPAD(0x1da, PIN_OUTPUT | MUX_MODE0) /* uart3_rts_irsd.uart3_tx_irtx */ 281 OMAP5_IOPAD(0x1dc, PIN_INPUT_PULLUP | MUX_MODE0) /* uart3_rx_irrx.uart3_usbb3_hsic */ 282 >; 283 }; 284 285 uart5_pins: pinmux_uart5_pins { 286 pinctrl-single,pins = < 287 OMAP5_IOPAD(0x1b0, PIN_INPUT_PULLUP | MUX_MODE0) /* uart5_rx.uart5_rx */ 288 OMAP5_IOPAD(0x1b2, PIN_OUTPUT | MUX_MODE0) /* uart5_tx.uart5_tx */ 289 OMAP5_IOPAD(0x1b4, PIN_INPUT_PULLUP | MUX_MODE0) /* uart5_cts.uart5_rts */ 290 OMAP5_IOPAD(0x1b6, PIN_OUTPUT | MUX_MODE0) /* uart5_cts.uart5_rts */ 291 >; 292 }; 293 294 dss_hdmi_pins: pinmux_dss_hdmi_pins { 295 pinctrl-single,pins = < 296 OMAP5_IOPAD(0x13c, PIN_INPUT | MUX_MODE0) /* hdmi_cec.hdmi_cec */ 297 OMAP5_IOPAD(0x140, PIN_INPUT | MUX_MODE0) /* hdmi_ddc_scl.hdmi_ddc_scl */ 298 OMAP5_IOPAD(0x142, PIN_INPUT | MUX_MODE0) /* hdmi_ddc_sda.hdmi_ddc_sda */ 299 >; 300 }; 301 302 tpd12s015_pins: pinmux_tpd12s015_pins { 303 pinctrl-single,pins = < 304 OMAP5_IOPAD(0x13e, PIN_INPUT_PULLDOWN | MUX_MODE6) /* hdmi_hpd.gpio7_193 */ 305 >; 306 }; 307}; 308 309&omap5_pmx_wkup { 310 pinctrl-names = "default"; 311 pinctrl-0 = < 312 &usbhost_wkup_pins 313 >; 314 315 palmas_sys_nirq_pins: pinmux_palmas_sys_nirq_pins { 316 pinctrl-single,pins = < 317 /* sys_nirq1 is pulled down as the SoC is inverting it for GIC */ 318 OMAP5_IOPAD(0x068, PIN_INPUT_PULLUP | MUX_MODE0) 319 >; 320 }; 321 322 usbhost_wkup_pins: pinmux_usbhost_wkup_pins { 323 pinctrl-single,pins = < 324 OMAP5_IOPAD(0x05a, PIN_OUTPUT | MUX_MODE0) /* fref_clk1_out, USB hub clk */ 325 >; 326 }; 327 328 wlcore_irq_pin: pinmux_wlcore_irq_pin { 329 pinctrl-single,pins = < 330 OMAP5_IOPAD(0x40, PIN_INPUT | MUX_MODE6) /* llia_wakereqin.gpio1_wk14 */ 331 >; 332 }; 333}; 334 335&mmc1 { 336 vmmc-supply = <&ldo9_reg>; 337 bus-width = <4>; 338}; 339 340&mmc2 { 341 vmmc-supply = <&vmmcsd_fixed>; 342 bus-width = <8>; 343 ti,non-removable; 344}; 345 346&mmc3 { 347 vmmc-supply = <&vmmcsdio_fixed>; 348 mmc-pwrseq = <&mmc3_pwrseq>; 349 bus-width = <4>; 350 non-removable; 351 cap-power-off-card; 352 pinctrl-names = "default"; 353 pinctrl-0 = <&mmc3_pins>; 354 interrupts-extended = <&wakeupgen GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH 355 &omap5_pmx_core 0x16a>; 356 357 #address-cells = <1>; 358 #size-cells = <0>; 359 wlcore: wlcore@2 { 360 compatible = "ti,wl1271"; 361 reg = <2>; 362 pinctrl-names = "default"; 363 pinctrl-0 = <&wlcore_irq_pin>; 364 interrupt-parent = <&gpio1>; 365 interrupts = <14 IRQ_TYPE_LEVEL_HIGH>; /* gpio 14 */ 366 ref-clock-frequency = <26000000>; 367 }; 368}; 369 370&mmc4 { 371 status = "disabled"; 372}; 373 374&mmc5 { 375 status = "disabled"; 376}; 377 378&i2c1 { 379 pinctrl-names = "default"; 380 pinctrl-0 = <&i2c1_pins>; 381 382 clock-frequency = <400000>; 383 384 palmas: palmas@48 { 385 compatible = "ti,palmas"; 386 /* sys_nirq/ext_sys_irq pins get inverted at mpuss wakeupgen */ 387 interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_LOW>; 388 reg = <0x48>; 389 interrupt-controller; 390 #interrupt-cells = <2>; 391 ti,system-power-controller; 392 ti,mux-pad1 = <0xa1>; 393 ti,mux-pad2 = <0x1b>; 394 pinctrl-names = "default"; 395 pinctrl-0 = <&palmas_sys_nirq_pins &palmas_msecure_pins>; 396 397 palmas_gpio: gpio { 398 compatible = "ti,palmas-gpio"; 399 gpio-controller; 400 #gpio-cells = <2>; 401 }; 402 403 extcon_usb3: palmas_usb { 404 compatible = "ti,palmas-usb-vid"; 405 ti,enable-vbus-detection; 406 ti,enable-id-detection; 407 ti,wakeup; 408 id-gpios = <&palmas_gpio 0 GPIO_ACTIVE_HIGH>; 409 }; 410 411 clk32kgaudio: palmas_clk32k@1 { 412 compatible = "ti,palmas-clk32kgaudio"; 413 #clock-cells = <0>; 414 }; 415 416 rtc { 417 compatible = "ti,palmas-rtc"; 418 interrupt-parent = <&palmas>; 419 interrupts = <8 IRQ_TYPE_NONE>; 420 ti,backup-battery-chargeable; 421 ti,backup-battery-charge-high-current; 422 }; 423 424 gpadc: gpadc { 425 compatible = "ti,palmas-gpadc"; 426 interrupts = <18 0 427 16 0 428 17 0>; 429 #io-channel-cells = <1>; 430 ti,channel0-current-microamp = <5>; 431 ti,channel3-current-microamp = <10>; 432 }; 433 434 palmas_pmic { 435 compatible = "ti,palmas-pmic"; 436 interrupt-parent = <&palmas>; 437 interrupts = <14 IRQ_TYPE_NONE>; 438 interrupt-names = "short-irq"; 439 440 ti,ldo6-vibrator; 441 442 smps123-in-supply = <&vsys_cobra>; 443 smps45-in-supply = <&vsys_cobra>; 444 smps6-in-supply = <&vsys_cobra>; 445 smps7-in-supply = <&vsys_cobra>; 446 smps8-in-supply = <&vsys_cobra>; 447 smps9-in-supply = <&vsys_cobra>; 448 smps10_out2-in-supply = <&vsys_cobra>; 449 smps10_out1-in-supply = <&vsys_cobra>; 450 ldo1-in-supply = <&vsys_cobra>; 451 ldo2-in-supply = <&vsys_cobra>; 452 ldo3-in-supply = <&vdds_1v8_main>; 453 ldo4-in-supply = <&vdds_1v8_main>; 454 ldo5-in-supply = <&vsys_cobra>; 455 ldo6-in-supply = <&vdds_1v8_main>; 456 ldo7-in-supply = <&vsys_cobra>; 457 ldo8-in-supply = <&vsys_cobra>; 458 ldo9-in-supply = <&vmmcsd_fixed>; 459 ldoln-in-supply = <&vsys_cobra>; 460 ldousb-in-supply = <&vsys_cobra>; 461 462 regulators { 463 smps123_reg: smps123 { 464 /* VDD_OPP_MPU */ 465 regulator-name = "smps123"; 466 regulator-min-microvolt = < 600000>; 467 regulator-max-microvolt = <1500000>; 468 regulator-always-on; 469 regulator-boot-on; 470 }; 471 472 smps45_reg: smps45 { 473 /* VDD_OPP_MM */ 474 regulator-name = "smps45"; 475 regulator-min-microvolt = < 600000>; 476 regulator-max-microvolt = <1310000>; 477 regulator-always-on; 478 regulator-boot-on; 479 }; 480 481 smps6_reg: smps6 { 482 /* VDD_DDR3 - over VDD_SMPS6 */ 483 regulator-name = "smps6"; 484 regulator-min-microvolt = <1350000>; 485 regulator-max-microvolt = <1350000>; 486 regulator-always-on; 487 regulator-boot-on; 488 }; 489 490 smps7_reg: smps7 { 491 /* VDDS_1v8_OMAP over VDDS_1v8_MAIN */ 492 regulator-name = "smps7"; 493 regulator-min-microvolt = <1800000>; 494 regulator-max-microvolt = <1800000>; 495 regulator-always-on; 496 regulator-boot-on; 497 }; 498 499 smps8_reg: smps8 { 500 /* VDD_OPP_CORE */ 501 regulator-name = "smps8"; 502 regulator-min-microvolt = < 600000>; 503 regulator-max-microvolt = <1310000>; 504 regulator-always-on; 505 regulator-boot-on; 506 }; 507 508 smps9_reg: smps9 { 509 /* VDDA_2v1_AUD over VDD_2v1 */ 510 regulator-name = "smps9"; 511 regulator-min-microvolt = <2100000>; 512 regulator-max-microvolt = <2100000>; 513 ti,smps-range = <0x80>; 514 }; 515 516 smps10_out2_reg: smps10_out2 { 517 /* VBUS_5V_OTG */ 518 regulator-name = "smps10_out2"; 519 regulator-min-microvolt = <5000000>; 520 regulator-max-microvolt = <5000000>; 521 regulator-always-on; 522 regulator-boot-on; 523 }; 524 525 smps10_out1_reg: smps10_out1 { 526 /* VBUS_5V_OTG */ 527 regulator-name = "smps10_out1"; 528 regulator-min-microvolt = <5000000>; 529 regulator-max-microvolt = <5000000>; 530 }; 531 532 ldo1_reg: ldo1 { 533 /* VDDAPHY_CAM: vdda_csiport */ 534 regulator-name = "ldo1"; 535 regulator-min-microvolt = <1800000>; 536 regulator-max-microvolt = <1800000>; 537 }; 538 539 ldo2_reg: ldo2 { 540 /* VCC_2V8_DISP: Does not go anywhere */ 541 regulator-name = "ldo2"; 542 regulator-min-microvolt = <2800000>; 543 regulator-max-microvolt = <2800000>; 544 /* Unused */ 545 status = "disabled"; 546 }; 547 548 ldo3_reg: ldo3 { 549 /* VDDAPHY_MDM: vdda_lli */ 550 regulator-name = "ldo3"; 551 regulator-min-microvolt = <1500000>; 552 regulator-max-microvolt = <1500000>; 553 regulator-boot-on; 554 /* Only if Modem is used */ 555 status = "disabled"; 556 }; 557 558 ldo4_reg: ldo4 { 559 /* VDDAPHY_DISP: vdda_dsiport/hdmi */ 560 regulator-name = "ldo4"; 561 regulator-min-microvolt = <1800000>; 562 regulator-max-microvolt = <1800000>; 563 }; 564 565 ldo5_reg: ldo5 { 566 /* VDDA_1V8_PHY: usb/sata/hdmi.. */ 567 regulator-name = "ldo5"; 568 regulator-min-microvolt = <1800000>; 569 regulator-max-microvolt = <1800000>; 570 regulator-always-on; 571 regulator-boot-on; 572 }; 573 574 ldo6_reg: ldo6 { 575 /* VDDS_1V2_WKUP: hsic/ldo_emu_wkup */ 576 regulator-name = "ldo6"; 577 regulator-min-microvolt = <1200000>; 578 regulator-max-microvolt = <1200000>; 579 regulator-always-on; 580 regulator-boot-on; 581 }; 582 583 ldo7_reg: ldo7 { 584 /* VDD_VPP: vpp1 */ 585 regulator-name = "ldo7"; 586 regulator-min-microvolt = <2000000>; 587 regulator-max-microvolt = <2000000>; 588 /* Only for efuse reprograming! */ 589 status = "disabled"; 590 }; 591 592 ldo8_reg: ldo8 { 593 /* VDD_3v0: Does not go anywhere */ 594 regulator-name = "ldo8"; 595 regulator-min-microvolt = <3000000>; 596 regulator-max-microvolt = <3000000>; 597 regulator-boot-on; 598 /* Unused */ 599 status = "disabled"; 600 }; 601 602 ldo9_reg: ldo9 { 603 /* VCC_DV_SDIO: vdds_sdcard */ 604 regulator-name = "ldo9"; 605 regulator-min-microvolt = <1800000>; 606 regulator-max-microvolt = <3000000>; 607 regulator-boot-on; 608 }; 609 610 ldoln_reg: ldoln { 611 /* VDDA_1v8_REF: vdds_osc/mm_l4per.. */ 612 regulator-name = "ldoln"; 613 regulator-min-microvolt = <1800000>; 614 regulator-max-microvolt = <1800000>; 615 regulator-always-on; 616 regulator-boot-on; 617 }; 618 619 ldousb_reg: ldousb { 620 /* VDDA_3V_USB: VDDA_USBHS33 */ 621 regulator-name = "ldousb"; 622 regulator-min-microvolt = <3250000>; 623 regulator-max-microvolt = <3250000>; 624 regulator-always-on; 625 regulator-boot-on; 626 }; 627 628 regen3_reg: regen3 { 629 /* REGEN3 controls LDO9 supply to card */ 630 regulator-name = "regen3"; 631 regulator-always-on; 632 regulator-boot-on; 633 }; 634 }; 635 }; 636 637 palmas_power_button: palmas_power_button { 638 compatible = "ti,palmas-pwrbutton"; 639 interrupt-parent = <&palmas>; 640 interrupts = <1 IRQ_TYPE_EDGE_FALLING>; 641 wakeup-source; 642 }; 643 }; 644 645 twl6040: twl@4b { 646 compatible = "ti,twl6040"; 647 #clock-cells = <0>; 648 reg = <0x4b>; 649 650 pinctrl-names = "default"; 651 pinctrl-0 = <&twl6040_pins>; 652 653 /* sys_nirq/ext_sys_irq pins get inverted at mpuss wakeupgen */ 654 interrupts = <GIC_SPI 119 IRQ_TYPE_LEVEL_LOW>; 655 656 /* audpwron gpio defined in the board specific dts */ 657 658 vio-supply = <&smps7_reg>; 659 v2v1-supply = <&smps9_reg>; 660 enable-active-high; 661 662 clocks = <&clk32kgaudio>, <&fref_xtal_ck>; 663 clock-names = "clk32k", "mclk"; 664 }; 665}; 666 667&mcpdm_module { 668 /* Module on the SoC needs external clock from the PMIC */ 669 pinctrl-names = "default"; 670 pinctrl-0 = <&mcpdm_pins>; 671 status = "okay"; 672}; 673 674&mcpdm { 675 clocks = <&twl6040>; 676 clock-names = "pdmclk"; 677}; 678 679&mcbsp1 { 680 pinctrl-names = "default"; 681 pinctrl-0 = <&mcbsp1_pins>; 682 status = "okay"; 683}; 684 685&mcbsp2 { 686 pinctrl-names = "default"; 687 pinctrl-0 = <&mcbsp2_pins>; 688 status = "okay"; 689}; 690 691&usbhshost { 692 port2-mode = "ehci-hsic"; 693 port3-mode = "ehci-hsic"; 694}; 695 696&usbhsehci { 697 phys = <0 &hsusb2_phy &hsusb3_phy>; 698}; 699 700&usb3 { 701 extcon = <&extcon_usb3>; 702 vbus-supply = <&smps10_out1_reg>; 703}; 704 705&dwc3 { 706 extcon = <&extcon_usb3>; 707 dr_mode = "otg"; 708}; 709 710&mcspi1 { 711 712}; 713 714&mcspi2 { 715 pinctrl-names = "default"; 716 pinctrl-0 = <&mcspi2_pins>; 717}; 718 719&mcspi3 { 720 pinctrl-names = "default"; 721 pinctrl-0 = <&mcspi3_pins>; 722}; 723 724&uart1 { 725 pinctrl-names = "default"; 726 pinctrl-0 = <&uart1_pins>; 727}; 728 729&uart3 { 730 pinctrl-names = "default"; 731 pinctrl-0 = <&uart3_pins>; 732 interrupts-extended = <&wakeupgen GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>, 733 <&omap5_pmx_core 0x19c>; 734}; 735 736&uart5 { 737 pinctrl-names = "default"; 738 pinctrl-0 = <&uart5_pins>; 739}; 740 741&cpu0 { 742 cpu0-supply = <&smps123_reg>; 743}; 744 745&dss { 746 status = "ok"; 747}; 748 749&hdmi { 750 status = "ok"; 751 752 /* vdda-supply populated in board specific dts file */ 753 754 pinctrl-names = "default"; 755 pinctrl-0 = <&dss_hdmi_pins>; 756 757 port { 758 hdmi_out: endpoint { 759 remote-endpoint = <&tpd12s015_in>; 760 }; 761 }; 762}; 763