1 /* 2 * (C) Copyright 2011 3 * Marvell Semiconductor <www.marvell.com> 4 * Written-by: Lei Wen <leiwen@marvell.com> 5 * 6 * SPDX-License-Identifier: GPL-2.0+ 7 */ 8 9 /* 10 * This file should be included in board config header file. 11 * 12 * It supports common definitions for MVEBU platforms 13 */ 14 15 #ifndef _MVEBU_CONFIG_H 16 #define _MVEBU_CONFIG_H 17 18 #include <asm/arch/soc.h> 19 20 #if defined(CONFIG_ARMADA_XP) 21 #define MV88F78X60 /* for the DDR training bin_hdr code */ 22 #endif 23 24 #define CONFIG_SYS_CACHELINE_SIZE 32 25 26 /* 27 * By default kwbimage.cfg from board specific folder is used 28 * If for some board, different configuration file need to be used, 29 * CONFIG_SYS_KWD_CONFIG should be defined in board specific header file 30 */ 31 #ifndef CONFIG_SYS_KWD_CONFIG 32 #define CONFIG_SYS_KWD_CONFIG $(CONFIG_BOARDDIR)/kwbimage.cfg 33 #endif /* CONFIG_SYS_KWD_CONFIG */ 34 35 /* Add target to build it automatically upon "make" */ 36 #ifdef CONFIG_SPL 37 #define CONFIG_BUILD_TARGET "u-boot-spl.kwb" 38 #endif 39 40 /* end of 16M scrubbed by training in bootrom */ 41 #define CONFIG_SYS_INIT_SP_ADDR 0x00FF0000 42 #define CONFIG_NR_DRAM_BANKS_MAX 2 43 44 #define MV_UART_CONSOLE_BASE MVEBU_UART0_BASE 45 46 /* 47 * SPI Flash configuration 48 */ 49 #ifdef CONFIG_CMD_SF 50 #define CONFIG_HARD_SPI 1 51 #define CONFIG_KIRKWOOD_SPI 1 52 #ifndef CONFIG_ENV_SPI_BUS 53 # define CONFIG_ENV_SPI_BUS 0 54 #endif 55 #ifndef CONFIG_ENV_SPI_CS 56 # define CONFIG_ENV_SPI_CS 0 57 #endif 58 #ifndef CONFIG_ENV_SPI_MAX_HZ 59 # define CONFIG_ENV_SPI_MAX_HZ 50000000 60 #endif 61 #endif 62 63 /* 64 * Ethernet Driver configuration 65 */ 66 #ifdef CONFIG_CMD_NET 67 #define CONFIG_CMD_MII 68 #define CONFIG_MII /* expose smi ove miiphy interface */ 69 #define CONFIG_MVNETA /* Enable Marvell Gbe Controller Driver */ 70 #define CONFIG_PHYLIB 71 #define CONFIG_ENV_OVERWRITE /* ethaddr can be reprogrammed */ 72 #define CONFIG_PHY_GIGE /* GbE speed/duplex detect */ 73 #endif /* CONFIG_CMD_NET */ 74 75 /* 76 * I2C related stuff 77 */ 78 #ifdef CONFIG_CMD_I2C 79 #ifndef CONFIG_SYS_I2C_SOFT 80 #define CONFIG_I2C_MVTWSI 81 #endif 82 #define CONFIG_SYS_I2C_SLAVE 0x0 83 #define CONFIG_SYS_I2C_SPEED 100000 84 #endif 85 86 /* Common SPL configuration */ 87 #ifndef CONFIG_SPL_LDSCRIPT 88 #define CONFIG_SPL_LDSCRIPT "arch/arm/mach-mvebu/u-boot-spl.lds" 89 #endif 90 91 #endif /* __MVEBU_CONFIG_H */ 92